Curtiss P-1 Hawk
The Curtiss P-1 Hawk was an American single-engine biplane fighter aircraft developed in the mid-1920s by the Curtiss Aeroplane and Motor Company as the first in a long family of taper-winged pursuit planes for the United States Army Air Corps (USAAC).[1] It featured an open cockpit, a water-cooled Curtiss D-12 V-12 inline engine producing 435 horsepower, and armament consisting of two synchronized .30-caliber machine guns firing through the propeller arc.[2] With a top speed of approximately 154-163 mph at sea level, a service ceiling of around 20,500-22,500 feet, and a range of 300-600 miles depending on the variant, the P-1 represented a significant advancement in U.S. fighter design during the interwar period, emphasizing speed, climb rate, and maneuverability over World War I-era biplanes.[2][1] The P-1's development stemmed from the earlier PW-8 prototype, which itself evolved from Curtiss racing aircraft of the early 1920s, with the USAAC ordering three PW-8s in April 1923 and the first P-1 variant following in March 1925.[1] Deliveries of the initial 15 P-1 aircraft began in August 1925, replacing the PW-8 in frontline service with units such as the 27th and 94th Pursuit Squadrons at Selfridge Field, Michigan.[2] The design incorporated a sesquiplane configuration with unequal wing spans—the upper wing at 31 feet 6 inches and the lower at 26 feet—along with a fixed tailskid landing gear, and it underwent progressive refinements for improved performance and reliability.[1][3] Several variants were produced to meet evolving USAAC needs, including the P-1A (25 built in 1925-1926 with a longer fuselage and D-12C engine), P-1B (25 ordered in 1926 featuring larger wheels and landing flares), and P-1C (33 delivered by April 1929 with wheel brakes for better ground handling).[2] A smaller batch of five P-2s was intended for the more powerful V-1400 engine but, due to engine delays, were completed with the D-12 and redesignated as P-1s, while later conversions like the P-1D, E, and F transformed advanced trainers back into single-seat fighters.[1] In total, over 90 P-1 family aircraft entered USAAC service, participating in key exercises such as the 1927 Air Corps maneuvers, the 1930 Spokane winter relocation (where 18 P-1s were involved, with 16 returning operational), and 1931 air operations involving 58 aircraft.[2][1] The P-1 Hawks served primarily with USAAC pursuit squadrons like the 17th, 27th, and 94th until their withdrawal from frontline duties after 1931, though some remained in training roles until 1935.[1] Limited exports included four to Bolivia, one P-1A to Japan, and 16 to Chile (eight each of P-1A and P-1B models), underscoring the type's influence on early international aviation.[2] Notably, a PW-8 variant achieved the first dawn-to-dusk transcontinental flight across the U.S. on June 23, 1924, piloted by Lt. Russell Maughan, highlighting the platform's potential for long-range operations.[2]Design and Development
Origins in PW-8
The Curtiss PW-8 pursuit aircraft originated from the successful Curtiss R-6 racer, which secured first and second places in the 1922 Pulitzer Trophy Race, prompting the U.S. Army Air Service to adapt its high-speed biplane design for military use. In early 1923, the XPW-8 prototype achieved its first flight on January 1, marking the beginning of this evolution toward a dedicated fighter. This development reflected the Air Service's push for advanced pursuit aircraft capable of superior speed and maneuverability, building on the R-6's lightweight frame and powerful engine. Key design features of the PW-8 included an all-metal biplane structure with a welded steel tube fuselage and fabric covering, tapered wings for improved aerodynamics, an open cockpit for the single-seat configuration, and power from a 410 hp Curtiss D-12 water-cooled V-12 engine. These elements established a robust yet agile platform, with the biplane layout providing stability for high-speed pursuits while the tapered wings reduced drag. The aircraft's armament introduced synchronized .30-caliber machine guns firing through the propeller arc, enhancing offensive capabilities without compromising the pilot's forward vision. In September 1923, the U.S. Army Air Service ordered production of 25 PW-8 aircraft, which were delivered starting in June 1924 and entered service that year, primarily assigned to the 17th Pursuit Squadron at Kelly Field, Texas. These fighters played a pivotal role in shaping early pursuit doctrine, emphasizing interception and escort missions, while their versatility was demonstrated through the addition of bomb racks for light ground attack duties. This foundational PW-8 design directly informed the subsequent P-1 Hawk as a refined production model with enhanced reliability.P-1 Production Series
The production series of the Curtiss P-1 Hawk commenced with the first flight of its prototype, the XPW-8B, on August 17, 1925, coinciding with the U.S. Army Air Service's introduction of the "P" designation for pursuit aircraft to standardize nomenclature for fighter types. This biplane fighter, developed from the earlier PW-8, featured mixed construction with a steel tube fuselage and wooden wings with fabric covering. A total of 98 P-1 aircraft were manufactured across the primary variants, serving as the backbone of U.S. Army pursuit squadrons through the late 1920s. The initial P-1 model included 15 examples built in 1925–1926, powered by the 435-hp Curtiss D-12 (V-1150-1) inline engine. The P-1A variant followed with 25 aircraft delivered in 1926, incorporating the 425-hp D-12A engine and a slightly lengthened fuselage for improved stability. Subsequent upgrades appeared in the P-1B, with 25 units produced and delivered starting in October 1926 using the D-12B engine, and the P-1C, comprising 33 aircraft delivered starting in April 1929 equipped with the 422-hp D-12C engine, which offered refined fuel injection for better performance at altitude. Five P-1s were completed with 500 hp Curtiss V-1400 engines as P-2 but redesignated P-1A due to engine issues. These inline-engine iterations emphasized reliability and ease of maintenance for standard service. Design refinements across the series focused on operational practicality, including an improved tunnel radiator integrated into the upper wing center section to replace earlier surface-mounted designs prone to icing and drag. Landing gear was strengthened with larger wheels on the P-1B and the addition of wheel brakes on the P-1C for enhanced ground handling on varied airfields. Standard armament consisted of two synchronized .30-caliber forward-firing machine guns mounted above the engine cowling, providing effective firepower for air-to-air engagements. The P-1 series formed the baseline for the broader Hawk family, with a total of 202 aircraft produced overall in pursuit configurations that equipped U.S. Army Air Corps units until the P-6 superseded them around 1930. Manufacturing occurred at Curtiss's primary facilities in Buffalo, New York, where the company's expertise in V-12 engine integration streamlined assembly for military contracts. This production run established the Hawk as a versatile platform, influencing later experimental variants such as the P-3.Experimental Pursuit Variants
The Curtiss P-3 represented an early experimental effort to adapt the P-1 Hawk airframe for radial engine power, with development beginning in 1927 and five aircraft constructed. These featured the Pratt & Whitney R-1340-3 Wasp nine-cylinder radial engine rated at 410 hp, marking a shift from the liquid-cooled inline engines of the standard series to evaluate air-cooled radial performance in pursuit roles. The prototype XP-3A achieved its first flight in July 1927, demonstrating notable improvements in climb rate to approximately 1,800 ft/min compared to the P-1, which aided in assessing radial engine viability for Army pursuits. Serial numbers for the P-3A evaluation models ranged from 27-316 to 27-320, with one example (the first P-3A) dedicated to Army testing and later contributing to NACA cowling refinements for radial installations. Building on radial experiments, the P-5 Superhawk pursued high-altitude capabilities through turbo-supercharging, with development initiated in 1928 and five aircraft produced, including prototypes designated XP-5 and XP-5A. Powered by the turbocharged Curtiss D-12F (V-1150-4) inline engine, which delivered up to 575 hp at altitude despite a sea-level rating of 435 hp, the P-5 achieved a top speed of 186 mph during testing, highlighting potential for elevated pursuit operations. However, the complex turbocharger system—mounted externally and adding significant weight—led to reliability concerns and operational accidents, resulting in rejection for production despite its advanced performance envelope. Serial numbers for the P-5 series spanned 28-395 to 28-399, with the aircraft focused on high-altitude evaluation rather than immediate service adoption. Both the P-3A and P-5 variants incorporated early NACA cowling designs to optimize airflow around their respective engine types, with the P-3A's radial setup particularly influencing subsequent low-drag enclosures tested at Langley. These experiments informed the evolution of later Hawk iterations, such as the P-6 series, by validating radial and supercharged configurations, though persistent reliability issues with the innovations prevented widespread production integration.Trainer Adaptations
The Curtiss P-1 Hawk airframes were adapted into advanced trainers during the late 1920s to support U.S. Army Air Corps (USAAC) pilot training programs, deriving directly from the P-1 structure but modified for dual-seat instruction. In October 1926, the USAAC placed an order for 40 AT-4 trainers, each powered by a 180 hp Wright-Hispano E engine, intended for advanced pursuit training with an emphasis on aerobatic maneuvers. However, only five AT-4s were completed, with the remaining 35 airframes instead converted to single-seat P-1D fighters equipped with 425 hp Curtiss D-12 engines. Of the AT-4 conversions, 35 were redesignated as P-1D fighters, extending the airframes' service life in frontline units. The AT-4 featured design modifications including an enlarged cockpit to seat an instructor alongside the student pilot, dual controls for two-person operation, and reduced armament consisting of a single machine gun forward, prioritizing training over combat readiness. These aircraft served briefly in USAAC advanced training roles at fields such as Kelly Field, Texas, before their rapid reversion to pursuit configuration. Between 1927 and 1928, Curtiss produced 36 examples of the related AT-5 series (five AT-5 and 31 AT-5A variants), also fitted with 220 hp Wright J-5 radial engines and incorporating dual controls for two-seat aerobatic and pursuit training. Like the AT-4, these emphasized instructional capabilities with a modified cockpit layout and minimal armament. The AT-5s were employed at USAAC training installations, including March Field, California, to develop advanced piloting skills before their conversion back to single-seat fighters restored full pursuit performance by 1932. Ultimately, five AT-5s became P-1E models, while 31 AT-5As were redesignated P-1F, thereby prolonging the overall utility of the Hawk trainer adaptations.Operational History
U.S. Army Air Corps Service
The Curtiss P-1 Hawk entered service with the U.S. Army Air Corps in 1925, marking the first aircraft to receive the new "P" (Pursuit) designation under the service's simplified naming system. The initial batch of fifteen P-1 aircraft was delivered to the 1st Pursuit Group at Selfridge Field, Michigan, primarily equipping the 27th and 94th Pursuit Squadrons, with later deliveries to the 95th and 17th. These early models, powered by Curtiss D-12 inline engines, underwent initial testing and familiarization flights at Selfridge before wider deployment. By late 1925, additional P-1 variants had joined squadrons at Kelly Field, Texas, and Rockwell Field, California, supporting the Air Corps' post-World War I expansion of tactical pursuit capabilities.[2][1] A notable precursor operation highlighting the Hawk lineage occurred in 1924, when U.S. Army Lt. Russell L. Maughan completed the first dawn-to-dusk transcontinental flight in a Curtiss PW-8, the direct predecessor to the P-1, covering 2,670 miles from Roosevelt Field, New York, to Crissy Field, San Francisco, in 20 hours and 48 minutes. The P-1 itself saw active use in Army maneuvers from 1926 to 1927, including large-scale exercises in Texas that tested pursuit tactics against simulated aerial threats. These operations emphasized the aircraft's role in rapid interception and reconnaissance, with squadrons demonstrating coordinated formation flying and mock engagements during joint Army-Air Corps drills. The type also participated in the 1930 Spokane winter relocation, where 18 P-1s were involved and 16 returned operational, and 1931 air operations involving 58 aircraft.[2][1] In service, the P-1 was armed with two synchronized .30-caliber machine guns mounted above the engine for forward firing, supplemented by provisions for a 100-pound bomb load on underwing racks for ground support roles. Tactics focused on air superiority exercises, where pilots practiced diving attacks and escort missions, though the biplane's open cockpit and fabric construction limited endurance in prolonged patrols. The aircraft proved reliable in training scenarios, contributing to the development of pursuit squadron doctrines amid the Air Corps' limited budget constraints of the era. Over 93 P-1 Hawks were procured by the Air Corps between 1925 and 1929, serving across multiple units including the 1st Pursuit Group in Michigan and Texas, the 95th Pursuit Squadron in California. These deployments spanned domestic bases and territorial outposts, with approximately 93 aircraft serving in pursuit roles across various units by the late 1920s. The P-1's frontline service began to wane by 1930 as it was progressively replaced by the more powerful Curtiss P-6 Hawk series, with many P-1s converted to advanced trainers (AT-4/AT-5) for continued use. The last operational flights in frontline and training roles occurred by 1935, after which surviving airframes were retired or scrapped as the Air Corps shifted to monoplane fighters.[2][1]International Deployments
The Curtiss P-1 Hawk achieved modest export success, with a total of 21 aircraft delivered to foreign operators as the Hawk I variant, typically equipped with the 425-horsepower Curtiss D-12 inline engine.[4] These sales focused on South American nations seeking modern biplane fighters for emerging air forces, though operational roles were generally limited to training, evaluation, and basic interception duties rather than extensive combat.[2] Bolivia acquired four P-1 Hawks in 1927 to bolster its aviation capabilities, primarily for pilot training ahead of regional tensions that escalated into the Chaco War (1932–1935).[5] The aircraft served in this role through the early 1930s, providing foundational experience for Bolivian aviators before the introduction of more advanced Hawk II models for active wartime operations.[6] Chile emerged as the primary export customer, purchasing eight P-1A Hawks in 1926 and eight P-1B variants in 1927 for frontline pursuit duties within the Chilean Air Force.[2] These aircraft formed the backbone of Chile's early fighter squadrons, performing interception and patrol missions until their retirement in the late 1930s amid attrition from accidents and the arrival of newer designs.[7] In 1927, a single P-1A was supplied to Japan for evaluation purposes, where it underwent testing but was not selected for production or widespread adoption.[8] Overall, international P-1 deployments highlighted the type's role as an interim solution for nascent air arms in South America, with minimal direct combat involvement compared to its U.S. service.[4]Variants and Operators
Pursuit and Prototype Models
The Curtiss P-1 Hawk pursuit series originated from the earlier PW-8 program, representing the U.S. Army Air Service's first dedicated pursuit aircraft under the new "P" designation scheme. The baseline PW-8, developed as a pursuit fighter, featured a biplane configuration with a Curtiss D-12 inline engine and served as the foundation for subsequent refinements in aerodynamics, radiator design, and structural improvements. Three prototypes, designated XPW-8, were ordered in April 1923 and delivered between May 1923 and September 1924, incorporating initial experiments with surface radiators that were prone to leaks. These led to modifications like the XPW-8B with tapered wings and a tunnel radiator for better performance. Production of the PW-8 followed with 25 aircraft delivered starting in June 1924, maintaining the core biplane design with the 435-hp D-12 engine but addressing early cooling issues through a core-type radiator.[2] The P-1 entered production in 1925 as the first standardized pursuit variant, with 10 aircraft built featuring tapered upper wings for reduced drag, an aerodynamically balanced rudder, and the 435-hp Curtiss V-1150-1 (D-12C) engine. This model marked a shift to mixed construction with a welded steel fuselage and wooden wings, improving durability over the PW-8. The initial order for 15 aircraft was split, with the remaining 5 completed as P-2 variants. The P-1A followed in 1926, with a total of 26 aircraft (23 new builds and 3 conversions from P-2s), extending the fuselage by 3 inches for better pilot visibility and upgrading the fuel system while retaining the D-12C engine. The P-1B, produced in 1927 with 25 units, introduced a rounded radiator housing, larger wheels, and provisions for night-landing flares, powered by the 435-hp V-1150-3 (D-12D) variant. By 1928-1929, the P-1C variant reached 33 aircraft, adding wheel brakes and hydraulic shock absorbers on the final two, all equipped with the 435-hp V-1150-5 (D-12E) engine for enhanced ground handling.[2][1] Parallel development included the P-2, a 1925 variant with 5 built, initially fitted with a 500-hp Curtiss V-1400 engine for increased power but redesignated from planned P-1s due to the larger powerplant; however, the V-1400 proved unreliable, leading to 3 conversions back to P-1A standard with D-12 engines. The XP-21 prototype, built in 1927 from a modified P-1A, explored further refinements such as radial engine integration (410-hp Pratt & Whitney R-1340-1) and served as a developmental stepping stone for later Hawk iterations, though only one was produced before redesignation.[2] Later pursuit models arose from conversions of trainer variants to restore fighter capabilities amid budget constraints. In 1930, 35 AT-4 advanced trainers were re-engined with the 435-hp D-12D and armed with .30-caliber machine guns to create the P-1D, effectively returning them to pursuit configuration with minimal structural changes. The P-1E followed in 1931, converting 5 AT-5 trainers similarly with D-12D powerplants and armament. Around 1930-1932, all 31 AT-5A trainers underwent the same process to form the P-1F, incorporating a longer fuselage akin to the P-1A for improved stability and re-engined with 435-hp D-12D engines along with full pursuit capabilities. These efforts extended the versatility of the Hawk design in U.S. Army service, with approximately 93 production pursuit aircraft in the P-1 to P-1C variants, plus conversions from trainer models.[2][1]| Variant | Quantity | Year | Engine | Key Differences |
|---|---|---|---|---|
| XPW-8/PW-8 | 3 prototypes + 25 production | 1923–1924 | Curtiss D-12 (435 hp) | Baseline biplane; prototypes tested radiator types; production fixed cooling issues with core radiator. |
| P-1 | 10 | 1925 | Curtiss V-1150-1 (D-12C, 435 hp) | Tapered wings, balanced rudder; mixed construction fuselage. |
| P-1A | 26 (23 new + 3 conversions) | 1926 | Curtiss D-12C (435 hp) | Extended fuselage, improved fuel system. |
| P-1B | 25 | 1927 | Curtiss V-1150-3 (D-12D, 435 hp) | Rounded radiator, larger wheels, night flares. |
| P-1C | 33 | 1928–1929 | Curtiss V-1150-5 (D-12E, 435 hp) | Wheel brakes, hydraulic shocks on last units. |
| P-2 | 5 (3 later to P-1A) | 1925 | Curtiss V-1400 (500 hp, initial) | Enlarged engine for power testing; unreliable, most reverted to D-12. |
| XP-21 | 1 | 1927 | Pratt & Whitney R-1340-1 (410 hp, experimental) | Radial engine testbed; developmental for advanced Hawks. |
| P-1D | 35 (from AT-4 conversions) | 1930 | Curtiss D-12D (435 hp) | Trainer conversion with armament restoration. |
| P-1E | 5 (from AT-5 conversions) | 1931 | Curtiss D-12D (435 hp) | Similar trainer-to-pursuit conversion. |
| P-1F | 31 (from AT-5A conversions) | 1930–1932 | Curtiss D-12D (435 hp) | Extended fuselage from trainer base, fighter reconfiguration. |
Trainer and Export Models
The trainer variants of the Curtiss P-1 Hawk were two-seat adaptations designed for advanced flight instruction in the U.S. Army Air Corps, featuring dual controls and reduced armament to prioritize pilot training over combat roles. These models utilized the core biplane structure of the P-1 series, with modifications for tandem seating and compatibility with lower-powered engines suitable for student pilots.[2] The XAT-4 served as the prototype for these trainers, converted from an existing P-1A airframe (serial 26-296) and delivered in July 1926 with an 180 hp Wright-Hispano E inline engine. It demonstrated the feasibility of the two-seat configuration for pursuit training, achieving a top speed of approximately 130 mph.[2] Production of the AT-4 followed in October 1926, with 40 aircraft ordered (serials 27-88 to 27-97 and 27-213 to 27-242), retaining the 180 hp Wright-Hispano E and offering a maximum speed of 133 mph at sea level. These were equipped with synchronized .30-caliber machine guns but emphasized instructional use; 35 examples were later re-engined with 435 hp Curtiss D-12D powerplants and converted to single-seat P-1D fighters by the early 1930s. The remaining five AT-4 airframes (serials 27-238 to 27-242) were completed instead as AT-5 trainers in 1927, fitted with a 220 hp Wright J-5 radial engine for better reliability and rough-field performance, attaining 125 mph. These AT-5s were subsequently redesignated P-1E after similar conversions to D-12D engines and fighter armament.[2][1] An enhanced version, the AT-5A, introduced a lengthened fuselage for improved stability and visibility, with 31 built starting in July 1927 (serials 28-42 to 28-72). Powered initially by the 220 hp Wright J-5, these advanced trainers supported more complex aerobatic and formation training; all 31 were converted to P-1F fighters around 1930-1932, receiving 435 hp Curtiss D-12D engines along with full pursuit capabilities.[2][1] Export models of the P-1 Hawk, marketed internationally as the Hawk I, adapted the design for foreign air services with variations in engine and equipment to suit local requirements, often retaining the single-seat fighter layout but with export-specific modifications like tropicalized components. Chile was the primary customer, acquiring eight P-1A Hawk I aircraft in 1926 equipped with 410 hp Curtiss D-12 inline engines, followed by eight P-1B Hawk I in 1927 with uprated 425 hp D-12 variants for enhanced climb rates up to 1,500 feet per minute.[2][9] Bolivia received four P-1 Hawk I exports in 1928, configured similarly to the P-1A with Hispano-Suiza or Curtiss D-12 engines to bolster its nascent air force capabilities. A single P-1 Hawk I was supplied to Japan in 1927 for evaluation by the Imperial Japanese Army Air Service, featuring the standard 410 hp D-12 engine and used to assess biplane fighter tactics. These exports highlighted the P-1's versatility, totaling 21 aircraft delivered abroad and demonstrating Curtiss's early success in global markets. Primary operators included the U.S. Army Air Corps pursuit squadrons (such as the 17th, 27th, and 94th) and the air forces of Chile, Bolivia, and Japan.[2][1]Preservation and Specifications
Surviving Examples
The sole confirmed surviving example of a Curtiss P-1 Hawk is a P-1 with manufacturer's construction number 60, on static display at the National Naval Aviation Museum in Pensacola, Florida.[10] Constructed in 1925, this aircraft originally served in the U.S. Army Air Corps inventory during the late 1920s, performing pursuit duties before being retired from active service around 1930 and entering storage.[10] Following its military career, it transitioned to civilian ownership, first with W. L. Hodson and later with Roy Reagan in Chico, California, under civil registration N6969 (cancelled in 1999).[10] The airframe underwent restoration to represent a U.S. Navy F6C-1 Hawk (a carrier-capable variant derived from the P-1 series), specifically marked as Bureau Number A6969, which had been lost in a crash landing on December 17, 1929.[10] Acquired by the National Naval Aviation Museum in 1986, it has remained a non-airworthy static exhibit in this configuration ever since, highlighting early interwar naval aviation.[10] No other complete P-1 Hawks are known to exist today, and there are no airworthy examples of the type. Some museums, such as the National Museum of the United States Air Force, preserve components or related artifacts from the Hawk family, but no additional full airframes from the P-1 production series have been verified as surviving.[10]Technical Data for P-1C
The Curtiss P-1C Hawk featured a crew of one pilot and measured 23 ft 0 in (7.01 m) in length, with a wingspan of 31 ft 6 in (9.60 m), height of 8 ft 9 in (2.67 m), and wing area of 252 sq ft (23.4 m²).[2] Its empty weight was 2,136 lb (969 kg) and gross weight was 2,973 lb (1,349 kg).[2] The aircraft was powered by a single Curtiss V-1150-5 (D-12E) V-12 inline liquid-cooled engine producing 435 hp (324 kW).[2] Performance included a maximum speed of 154 mph (248 km/h) at sea level, cruise speed of 124 mph (200 km/h), range of 328 mi (528 km), service ceiling of 20,800 ft (6,300 m), and initial rate of climb of 1,460 ft/min (7.4 m/s).[2] These figures yielded a wing loading of 11.8 lb/sq ft (57.6 kg/m²) and power-to-weight ratio of 0.146 hp/lb (2.40 kW/kg).[2] Armament consisted of two synchronized .30-caliber machine guns, along with provisions for carrying up to 50 lb (23 kg) of bombs (two 25 lb bombs) on underwing racks.[2]| Specification | Value |
|---|---|
| Crew | 1 |
| Length | 23 ft 0 in (7.01 m) |
| Wingspan | 31 ft 6 in (9.60 m) |
| Height | 8 ft 9 in (2.67 m) |
| Wing area | 252 sq ft (23.4 m²) |
| Empty weight | 2,136 lb (969 kg) |
| Gross weight | 2,973 lb (1,349 kg) |
| Powerplant | 1 × Curtiss V-1150-5 (D-12E) V-12 inline, 435 hp (324 kW) |
| Maximum speed | 154 mph (248 km/h) at sea level |
| Cruise speed | 124 mph (200 km/h) |
| Range | 328 mi (528 km) |
| Service ceiling | 20,800 ft (6,300 m) |
| Rate of climb | 1,460 ft/min (7.4 m/s) |
| Wing loading | 11.8 lb/sq ft (57.6 kg/m²) |
| Power/mass | 0.146 hp/lb (2.40 kW/kg) |
| Armament | 2 × .30-cal machine guns; provisions for 50 lb (two 25 lb) bombs |