.38 Special
The .38 Special, formally known as the .38 Smith & Wesson Special, is a rimmed, straight-walled, centerfire revolver cartridge developed in the United States in 1898.[1] It features a bullet diameter of 0.357 to 0.358 inches, a case length of 1.155 inches, a rim diameter of 0.440 inches, and uses a small pistol primer.[1][2] Standard loads operate at a maximum average pressure of 17,000 psi, while +P variants increase this to 20,000 psi for enhanced performance in modern firearms.[1][3] Introduced by Smith & Wesson in 1899 specifically for their new K-frame "Military & Police" revolver, the .38 Special was created as a direct improvement over the .38 Long Colt, which had proven inadequate in stopping power during conflicts like the Spanish-American War.[4] The original loading consisted of a 158-grain lead round-nose bullet propelled by 21.5 grains of black powder at around 775 feet per second, penetrating eight and a half 7/8-inch pine boards—25% more than its predecessor.[4] This design emphasized reliability and controllability in double-action revolvers, making it suitable for both military and civilian applications from the outset.[4] The cartridge quickly gained traction in law enforcement and military circles; by the early 1900s, the U.S. Army and Navy each ordered 1,000 Smith & Wesson revolvers chambered for it, solidifying its role as a standard service round.[4] Throughout the 20th century, it became a staple for American police departments, self-defense, and target shooting due to its manageable recoil and versatility with bullet weights ranging from 110 grains (jacketed, up to 1,000 fps) to 158 grains (lead, around 800 fps).[4][3] Notable evolutions include the 1930s ".38/44 High Velocity" loads reaching 1,100 fps in heavy-frame revolvers, the 1950s adoption of 130-grain full metal jacket rounds by the U.S. Air Force, and the 1970s introduction of the 158-grain +P semi-wadcutter hollow-point "FBI Load" for superior expansion and stopping power.[4] Today, the .38 Special remains one of the most produced and widely used handgun cartridges, favored for concealed carry, training, and reloading due to its compatibility with .357 Magnum revolvers and low-pressure options for older firearms.[3]Design and Specifications
Physical Dimensions
The .38 Special cartridge features a bullet diameter of 0.357 inches (9.07 mm), which accommodates lead or jacketed projectiles designed for reliable expansion and penetration in revolver chambers.[5] The case length measures 1.155 inches (29.34 mm), providing sufficient powder capacity for standard loads while maintaining compatibility with revolver cylinders. Overall cartridge length is limited to a maximum of 1.55 inches (39.37 mm) to ensure proper feeding and chambering without excessive protrusion.[6] The rim diameter stands at 0.440 inches (11.18 mm), with a corresponding base diameter of 0.379 inches (9.63 mm), characteristic of its rimmed design that facilitates headspacing in revolvers by allowing the extractor to engage the rim securely.[1] This configuration supports straightforward ejection and reloading in double-action mechanisms. The cartridge's straight-walled case profile, with minimal taper from base to mouth, promotes consistent alignment and reliable feeding in revolver cylinders, reducing the risk of malfunctions during rapid fire.[7] Standard pressure limits are established by the Sporting Arms and Ammunition Manufacturers' Institute (SAAMI) at 17,000 psi for conventional loads, ensuring safe operation in firearms rated for the cartridge.[5] The Commission Internationale Permanente (CIP) specifies a maximum average pressure of 1,500 bar (approximately 21,756 psi), with dimensional tolerances aligned to international manufacturing standards for interoperability.[6] These specifications evolved from the earlier .38 Long Colt by extending the case length for improved ballistic performance while retaining core dimensional compatibility.[8]Components and Construction
The .38 Special cartridge is constructed with a rimmed, straight-walled case made from brass, typically a 70/30 copper-zinc alloy that provides durability and resistance to corrosion while allowing for repeated resizing in reloading.[9] The case is formed through a drawing process starting from a flat brass disk or cup, which is progressively extruded and drawn into the final cylindrical shape with an integrated rim for headspacing in revolvers.[9] Primers used in .38 Special ammunition are predominantly boxer-style small pistol primers, featuring a single central flash hole and an integrated anvil for reliable ignition, though some surplus or imported variants may employ Berdan primers with multiple flash holes and an anvil formed in the case itself.[10] The primer is seated into a shallow pocket at the base of the brass case to ensure a secure fit and consistent firing pin strike. Originally loaded with black powder upon its introduction, the .38 Special transitioned to smokeless powder in the early 1900s as propellant technology advanced, with modern factory and handloaded ammunition utilizing fast-burning smokeless powders such as Alliant Unique or Bullseye to achieve efficient combustion within the cartridge's modest case capacity.[11][12] Bullets for the .38 Special vary in construction to suit different purposes, commonly ranging from 110 to 158 grains in weight and including options like soft lead round-nose for general use, full-metal-jacketed for training, or hollow-point designs for expansion in defensive applications.[12] Target loads often employ wadcutter bullets with a flat meplat for clean, precise scoring on paper, while semi-wadcutter profiles—featuring a flat nose with a shoulder for secure crimping—are favored in defensive or carry loads to balance penetration and accuracy.[12] The assembly process involves inserting the primer into the case base, followed by charging the case with the measured powder charge, then seating the bullet into the case mouth and applying a crimp—typically a taper or roll crimp—to secure the bullet and seal the assembly against pressure escape during firing.[13] This construction ensures reliable containment of the low-pressure load, typically around 17,000 psi. Due to its similar case dimensions, the .38 Special is compatible with chambers designed for the more powerful .357 Magnum.[14]History
Development and Introduction
The .38 Special cartridge was developed in 1898 by engineers at Smith & Wesson as an extension of the .38 Long Colt, featuring a longer case to accommodate additional propellant for enhanced performance.[15] This design addressed the limitations of the .38 Long Colt, which had demonstrated insufficient stopping power during the Philippine-American War, where U.S. forces encountered determined resistance that highlighted the need for greater velocity and penetration in military sidearms.[16] The cartridge's initial configuration utilized black powder, propelling a 158-grain lead round-nose bullet at velocities ranging from 800 to 900 feet per second, providing improved ballistic characteristics over its predecessor.[4] Smith & Wesson introduced the .38 Special alongside their new Hand Ejector revolver, known as the Military & Police model, a solid-frame, swing-out cylinder design on the K-frame that allowed for rapid reloading via the side-swinging cylinder and simultaneous manual extraction using the ejector star, marking a significant advancement in revolver engineering for the era.[15] By the early 1900s, the cartridge transitioned to smokeless powder loadings, which further refined its performance without altering the fundamental case dimensions established in 1898.[4]Adoption in Military and Law Enforcement
The U.S. military's adoption of the .38 Special cartridge began in the early 20th century as a supplement to existing .38 Long Colt revolvers, with the Navy ordering 1,000 Smith & Wesson Military & Police models chambered for .38 Special in 1900, followed by a similar Army order in 1901.[15] Although the cartridge did not become the primary military sidearm—superseded by the .45 ACP in the 1911 pistol—it was issued in revolvers for various roles, including during World War I for rear-echelon and training units.[4] In World War II, production surged to meet demand, with the Smith & Wesson Victory Model revolver, chambered in .38 Special, manufactured under contract for the U.S. Navy and Marine Corps to arm aircrew and shipboard personnel, totaling over 350,000 units.[17] The Colt Commando, a simplified .38 Special revolver, was also produced in large numbers starting in 1942 for military and allied forces, emphasizing rapid wartime output.[18] Remington Arms developed specialized steel-jacketed .38 Special ammunition in 1943 specifically for naval contracts, addressing shortages in traditional jacketed rounds.[19] The cartridge continued in limited military use through the Korean War and Vietnam, such as for embassy security details and military police.[20] In law enforcement, the .38 Special rapidly became the standard cartridge in the United States during the 1920s, replacing weaker .38 S&W loads due to its improved power and reliability in double-action revolvers like the Smith & Wesson Model 10 and Colt Official Police.[21] The New York City Police Department (NYPD) formalized its adoption in May 1926, issuing it alongside approved revolvers and marking a shift toward standardized, higher-velocity ammunition for urban policing.[22] The Federal Bureau of Investigation (FBI) similarly equipped agents with .38 Special revolvers from the 1930s onward, favoring models like the Colt Official Police for their balance of concealability and stopping power.[23] Usage peaked through the mid-20th century, with the cartridge serving as the backbone of American police arsenals into the 1990s, as departments valued its manageable recoil and proven track record in close-quarters encounters.[24] A pivotal development occurred in 1972 when the FBI adopted the 158-grain +P lead semi-wadcutter hollow-point load—known as the "FBI Load"—for its enhanced expansion and penetration in short-barreled revolvers, influencing other agencies like those in Chicago and Dallas.[25] This followed evaluations of terminal ballistics and was further underscored by the 1986 FBI Miami shootout, where the load's performance highlighted limitations of .38 Special revolvers against determined assailants armed with rifles, prompting refinements in training and ammunition.[26] By the 1980s, the U.S. military began phasing out .38 Special revolvers in favor of the 9mm Beretta M9 pistol, adopted in 1985 to standardize with NATO allies and increase magazine capacity.[27] Law enforcement followed suit in the 1990s, transitioning to semi-automatic pistols like the Glock 19 in 9mm for higher round counts and faster reloads, though some departments retained .38 Special backups into the early 2000s.[28]Ballistics and Performance
Standard Ballistic Characteristics
The standard .38 Special cartridge adheres to SAAMI maximum average pressure limits of 17,000 psi (CUP), which ensures safe operation in older revolvers designed for black powder-era loads.[29] This conservative pressure standard prioritizes reliability and reduced wear on firearms while delivering consistent performance for target shooting and defensive use. Typical muzzle velocities for factory-loaded 158-grain bullets fired from a 4-inch barrel range from 755 to 800 fps, generating muzzle energies of 200 to 225 ft-lbs.[30] Lighter 125-grain loads achieve velocities around 775 fps, yielding approximately 167 ft-lbs of energy, emphasizing the cartridge's balance of controllability and penetration over raw power.[30] These velocities are from a 4-inch barrel; shorter barrels (e.g., 2-inch) reduce velocity by 100-150 fps, lowering energy accordingly.[31] The .38 Special exhibits mild recoil, with free recoil energy measuring 2 to 3 ft-lbs in a standard 2.25-pound revolver, facilitating rapid follow-up shots.[32] Its trajectory remains relatively flat for handgun standards, supporting practical engagement distances up to 25 yards.| Bullet Weight (gr) | Type | Muzzle Velocity (fps, 4" barrel) | Muzzle Energy (ft-lbs) | Manufacturer Example |
|---|---|---|---|---|
| 125 | JSP | 775 | 167 | Winchester |
| 158 | LRN | 755 | 200 | Winchester |
| 158 | CLL | 800 | 225 | Remington |
Enhanced Loads and Terminal Effects
Enhanced loads for the .38 Special cartridge, particularly +P variants, operate at higher pressures to achieve improved velocity and energy compared to standard-pressure ammunition. The Sporting Arms and Ammunition Manufacturers' Institute (SAAMI) approves .38 Special +P loads up to a maximum average pressure (MAP) of 20,000 psi, an increase from the 17,000 psi limit for standard loads.[34] For example, a typical 125-grain jacketed hollow-point (+P) bullet achieves muzzle velocities around 1,000–1,050 feet per second, delivering approximately 300–310 foot-pounds of muzzle energy from a 4-inch barrel.[35] Unofficial +P+ loads exceed SAAMI specifications, often reaching pressures up to 22,000 psi or higher, but they lack standardization and pose risks of firearm damage, accelerated wear, or catastrophic failure in revolvers not explicitly rated for such pressures.[36] These enhanced loads enhance terminal ballistics primarily through better bullet expansion and controlled penetration. Hollow-point designs in +P configurations typically expand to diameters of 0.5–0.7 inches upon impact with soft tissue simulants, while achieving 12–18 inches of penetration in 10% ballistic gelatin, aligning with FBI protocol standards for optimal wound channel creation without excessive overpenetration.[31] In contrast, standard-pressure loads, such as 158-grain lead round nose bullets, often fail to expand reliably, leading to deeper penetration beyond 20 inches and increased overpenetration risks in defensive scenarios.[31] Wound ballistics for .38 Special enhanced loads emphasize permanent cavity formation over temporary effects, as their subsonic velocities (generally below 1,125 feet per second) limit hydrostatic shock—the rapid pressure wave that can disrupt tissue beyond the bullet path.[37] This makes them particularly effective against unarmored human threats, where expansion creates a larger wound diameter and energy transfer focuses on vital organ disruption, though they produce less remote wounding than high-velocity rifle rounds.[31] Ballistic gel tests from the 1980s through the 2000s, including evaluations of the FBI's adopted 158-grain +P lead semi-wadcutter hollow-point load, demonstrated superior performance over standard variants. These tests showed consistent expansion to 0.6–0.75 inches with 14–16 inches of penetration, outperforming non-expanding standard loads by creating wider, more incapacitating wound channels in gelatin calibrated to human tissue density.[25]Applications and Usage
Compatible Firearms
The .38 Special cartridge, with its rimmed case design, is primarily compatible with double-action revolvers, which facilitate reliable extraction and headspacing via the cartridge rim. Iconic examples include the Smith & Wesson Model 10, originally introduced in 1899 as the .38 Hand Ejector Military & Police, a medium-frame six-shot revolver that became the standard for law enforcement and civilian use due to its robust K-frame construction and fixed sights. Over 6 million Model 10s have been produced since its inception, underscoring its enduring popularity and continuous manufacturing. Similarly, the Colt Official Police, a medium-frame double-action revolver with a six-round cylinder, served as a staple police sidearm from the early 20th century, offering positive lockup and smooth action tailored to the .38 Special's dimensions. The Ruger SP101, introduced in the 1980s, represents another classic with its stainless steel frame, five-shot capacity in .38 Special +P, and cushioned grip for recoil management, emphasizing durability in a compact package. Modern firearms chambered for .38 Special continue to prioritize revolver designs for concealed carry and versatility. The Smith & Wesson 642 Airweight, a lightweight J-frame model with an aluminum alloy frame and five-round cylinder, weighs just 14.6 ounces unloaded, making it ideal for everyday carry while handling standard .38 Special loads effectively. Taurus offers the Model 856, a six-shot small-frame revolver with a steel frame and options for 2- to 3-inch barrels, providing enhanced capacity over traditional five-shot snubbies without sacrificing concealability. For longer-range applications, the Henry Big Boy lever-action carbine, chambered in .357 Magnum/.38 Special, accommodates the cartridge in its six-round tubular magazine, delivering rifle-like accuracy with handgun ammunition. Current manufacturers like Charter Arms produce the Undercover, a five-shot double-action-only revolver with a 2-inch barrel and lightweight aluminum frame, maintaining the cartridge's legacy in compact, affordable platforms. The .38 Special can be safely fired in .357 Magnum revolvers, as the longer chambers of the latter accommodate the shorter .38 case without excessive headspace, allowing users to select milder loads for practice or recoil-sensitive shooting. However, the cartridge is not typically compatible with semi-automatic pistols, which are designed for rimless ammunition; adaptations like moon clips are required only for loading rimless variants into revolvers, not for standard .38 Special use in semi-autos, where few models exist due to extraction challenges.Practical Uses and Modern Relevance
The .38 Special remains a popular choice for concealed carry and self-defense among civilians due to its manageable recoil and reliability in compact revolvers, making it suitable for everyday carry in urban environments.[38] Its lower recoil compared to higher-pressure cartridges like 9mm allows for quicker follow-up shots and better control, particularly in snub-nose designs favored by beginners transitioning to personal protection firearms.[39] Modern +P loads, such as jacketed hollow points, enhance stopping power while minimizing overpenetration risks in densely populated areas, aligning with 2020s defensive training emphases on urban safety.[38][40] In recreational applications, the cartridge excels for small game hunting and varmint control at ranges up to 50 yards, where its accuracy from longer-barreled revolvers provides ethical takedowns on targets like squirrels or rabbits without excessive tissue damage.[41] For target shooting and plinking, the .38 Special's low cost and mild report make it ideal for casual range sessions, while its compatibility with revolver divisions in competitions like IPSC supports precision shooting in minor power factor categories.[42] Reloaders continue to favor the .38 Special for its versatility in crafting custom loads tailored to specific needs, from light training rounds to enhanced defensive options, sustaining its popularity among enthusiasts in the 2020s.[43] The cartridge's low-pressure design appeals to new shooters for introductory training, offering a forgiving platform that builds confidence with reduced flinch and easier mastery of fundamentals before advancing to more potent calibers.[44] This accessibility has contributed to its ongoing relevance in civilian self-defense courses, where data from ballistic testing highlights its balanced performance in close-quarters scenarios. Globally, the .38 Special persists in law enforcement contexts in revolver-preferring nations like Brazil, where it serves as a reliable backup option amid preferences for simple, jam-resistant firearms.[45]Variants and Comparisons
Derived Variants
The .38 Special cartridge has seen several derived variants developed to enhance performance, adapt to specific uses, or meet modern regulatory needs, while maintaining compatibility with standard chamber dimensions. In the 1970s, ammunition manufacturers responded to demands for increased velocity from law enforcement by introducing higher-pressure loadings. The +P variant, standardized by SAAMI in 1974 at a maximum average pressure of 20,000 psi (compared to 17,000 psi for standard loads), allows for greater powder charges to achieve higher muzzle velocities without altering the cartridge case.[36] Winchester played a key role in this development, releasing early +P loads such as the 158-grain lead semi-wadcutter hollow point (LSWCHP) in collaboration with the St. Louis Police Department around 1973, which later influenced the FBI's adoption of similar ammunition.[4] These +P loads provide ballistic enhancements like velocities up to 200 fps greater than standard-pressure equivalents, improving expansion and penetration in defensive scenarios.[36] Building on +P, the +P+ variant emerged as a non-standardized, higher-pressure option exceeding SAAMI specifications, typically around 23,500 CUP, initially restricted to law enforcement use. Winchester introduced its +P+ loading in 1974, such as the 110-grain jacketed hollow point Treasury Load, to deliver even greater velocities for specialized applications.[36] Modern boutique manufacturers like Buffalo Bore continue this lineage with +P+ equivalents, exemplified by their 125-grain jacketed hollow point achieving approximately 1,100 fps from a 2-inch barrel, optimized for short-barreled revolvers while remaining safe in +P-rated firearms.[46] These variants require firearms marked for +P or stronger construction to handle the elevated pressures safely. For precision shooting, wadcutter and match loads represent another key derivation, prioritizing accuracy and reduced recoil over power. The 148-grain lead wadcutter bullet, seated deeply in the case for a flat trajectory, became standard for target practice in the mid-20th century, often loaded to subsonic velocities around 700-800 fps to minimize noise and barrel wear in indoor ranges.[15] These loads, such as Federal's Gold Medal series with match-grade primers and consistent powder charges, were favored in competitions using revolvers like the Smith & Wesson Model 52, producing clean, scorable holes in paper targets.[47] Early black powder loads constitute an obsolete variant from the cartridge's origins, reflecting its 1898 introduction before widespread smokeless powder adoption. The initial factory loading used 21 grains of black powder behind a 158-grain lead round-nose bullet, achieving about 775 fps, but these were phased out by 1900 as smokeless equivalents proved superior in cleanliness and performance.[15] Today, black powder reproductions are niche, primarily for historical reenactments, though they underscore the cartridge's evolution from black powder roots. In the 2020s, manufacturing updates have focused on environmental compliance, leading to lead-free and frangible variants for training and range use. Federal's American Eagle Indoor Range Training load, featuring a 100-grain copper-plated lead-free bullet and non-lead primer, complies with regulations reducing airborne lead exposure in indoor facilities, maintaining similar ballistics to traditional loads at 960 fps.[48] Frangible bullets, often copper-based, disintegrate on impact with steel backstops to minimize ricochet risks, as seen in Buffalo Bore's +P lead-free offerings for short-barrel applications, addressing both safety and ecological concerns in modern shooting environments.[49]Comparisons to Other Cartridges
The .38 Special cartridge offers lower recoil and magazine capacity compared to the 9mm Luger, making it more suitable for shooters sensitive to kick or those using compact revolvers, though the 9mm delivers higher typical muzzle energy around 350 ft-lbs versus the .38 Special's maximum of approximately 300 ft-lbs with +P loads.[50][24] The .38 Special's ammunition is generally cheaper for practice, averaging $0.45–$0.75 per round in 2025, but its availability is more limited in semi-automatic platforms due to the cartridge's rimmed design optimized for revolvers.[51] In comparison to the .357 Magnum, the .38 Special serves as a milder alternative with roughly half the chamber pressure—17,000 psi standard versus 35,000 psi—resulting in significantly reduced recoil and wear on firearms.[52] Ammunition is interchangeable in revolvers chambered for .357 Magnum, allowing .38 Special rounds to be fired safely, but the reverse is not true: .357 Magnum rounds cannot be used in .38 Special-only guns due to the longer case length (1.290 inches versus 1.155 inches) and excessive pressure, which could cause catastrophic failure.[53] The .38 Special exhibits superior ballistics to the .380 ACP, with greater penetration depth in ballistic gel tests—often exceeding 12 inches compared to the .380 ACP's marginal performance—and higher overall energy delivery, though at the cost of increased recoil.[54][51] The following table summarizes representative standard loads from major manufacturers, based on 4-inch barrel testing:| Cartridge | Bullet Weight (gr) | Muzzle Velocity (fps) | Muzzle Energy (ft-lbs) | Avg. Practice Price per Round (2025) |
|---|---|---|---|---|
| .38 Special | 158 | 755 | 200 | $0.45–$0.75 |
| .380 ACP | 95 | 955 | 188 | $0.40–$0.70 |