Fact-checked by Grok 2 weeks ago

Fender Hot Rod DeVille

The Fender Hot Rod DeVille is a renowned line of all-tube guitar combo amplifiers manufactured by Fender Musical Instruments Corporation, celebrated for delivering versatile, high-headroom tones suitable for both stage and studio use. Introduced in 1996 as part of Fender's Hot Rod series, it builds on the earlier Blues DeVille models from the 1990s, offering a 60-watt output powered by two 6L6 tubes, three 12AX7 preamp tubes, and configurations such as dual 12-inch Celestion A-Type speakers in the flagship 212 model, providing classic Fender cleans with enhanced overdrive and reverb.^[1]^[2]^[3] The Hot Rod DeVille series emerged in the mid-1990s amid a shift in guitar amplification toward simpler, more reliable tube designs, evolving from Fender's 1993 Blues series—which included the 60-watt Blues DeVille—to incorporate a "Drive" channel for boosted gain while retaining the brand's signature sparkling clean tones.^[1]^[2] Over the years, the amplifier has seen iterative updates across generations: the original model featured a pine cabinet and spring reverb; the Series II added more gain staging; the Series III in 2010 introduced improved speaker options like Celestion G12P-80s in some variants; and the current Series IV, launched in 2018, refined the preamp for tighter overdriven note definition, enhanced bass response, increased clean headroom, and an updated rear panel with a series effects loop for easier integration of pedals and processors.^[4]^[5]^[2] Key to its enduring popularity among gigging musicians is the three-channel operation—Normal for pristine cleans, Drive for moderate crunch, and More Drive for higher-gain leads—controlled via front-panel volume, treble, mid, bass, reverb, and presence knobs, with a rear bias adjustment for tube customization.^[3]^[6] The 212 IV model, weighing 55.25 pounds (25.06 kg) in a lightweight pine cabinet, measures 21 × 24.25 × 10.75 inches (53.34 × 61.59 × 27.3 cm) and includes XLR direct output for PA integration, making it a staple for blues, rock, and country players seeking Fender's warm, dynamic response without excessive complexity.^[6]^[3] Priced around $1,260 for the IV edition, it remains one of Fender's best-selling amplifiers due to its balance of power, portability, and tonal flexibility.^[3]^[7]

History

Introduction and Development

The Fender Hot Rod DeVille was introduced in 1996 as a higher-gain evolution of the earlier Blues DeVille amplifier, part of Fender's effort to modernize its tube amp lineup.^[8] Developed within the broader Hot Rod series, it targeted guitarists shifting from the complex, high-gain rack systems popular in the 1980s to more straightforward combo amplifiers that retained analog warmth and reliability.^[9]^[1] Initial production occurred in the United States, emphasizing a fusion of Fender's signature clean tones with improved overdrive circuits for greater versatility across genres.^[10] The design prioritized a 60-watt output suitable for live gigging, multi-channel operation for seamless switching between clean and driven sounds, and pricing that made high-quality tube amplification more accessible than costly vintage reissues.^[1]^[8] As a sister model to the Hot Rod Deluxe, the DeVille incorporated larger transformers to provide additional headroom while maintaining a compact combo form.^[11]

Evolution of Versions

The Fender Hot Rod DeVille Series II, introduced in the late 1990s, featured Fender Special Design speakers manufactured by Eminence for both the 212 and 410 configurations, providing a balanced tone suitable for stage use.^[12] The amp's cabinet was covered in basic black tolex, contributing to its durable, roadworthy build.^[12] An initial effects loop was included, allowing integration of external pedals while maintaining the amp's core tube-driven sound.^[12] In 2010, the Series III brought refinements for improved performance, adopting Celestion G12-P80 speakers in the 212 model to deliver a tighter low-end response and enhanced clarity.^[13] The control panel was updated to a black, non-reflective finish for better visibility during live settings.^[13] This series also incorporated enhanced modern distortion voicing in the drive channels for more versatile overdrive tones, along with minor tweaks to the spring reverb circuit for subtle improvements in sustain and decay.^[14] The Series IV, launched in the 2010s and continuing into the present, focused on further tonal and ergonomic enhancements. The preamp was modified to provide improved overdriven note definition, allowing for greater articulation in high-gain scenarios.^[3] The spring reverb circuit was refined for smoother operation and more natural ambiance.^[3] Celestion A-Type speakers were standard in the 212 model, offering enhanced midrange punch and overall responsiveness.^[3] Cabinets shifted to lighter pine construction, reducing weight without compromising resonance or bass response.^[6] Across all series, the amp maintained a consistent 60-watt output for reliable power in live and studio environments.^[3] Production of the Hot Rod DeVille initially occurred in the USA at Fender's Corona, California facility, but shifted to Mexico around 2002 for greater cost efficiency, with no significant decline in build quality or component standards.^[7] In later series, particularly IV, the 410 model was discontinued, with Fender prioritizing the 212 variant as the primary offering due to its balance of portability and power.^[12]

Design and Features

Circuitry and Components

The Fender Hot Rod DeVille employs a tube complement consisting of three 12AX7 preamp tubes dedicated to the gain stages and two 6L6 power tubes configured in a Class AB push-pull output for delivering 60 watts of power.^[15] This setup provides the amp's characteristic clean headroom and overdriven tones, with the preamp tubes handling multiple gain stages across its three channels. The power tubes operate in fixed bias mode, allowing for adjustments to optimize performance and tube life.^[16] The circuit design is a modified version of the Blues DeVille architecture, featuring increased preamp gain specifically for the drive channels to enhance overdriven note definition and sustain.^[8] Key elements include a cathodyne phase inverter—essentially a cathode-follower configuration using a single triode—for balanced drive to the power tubes, which contributes to the amp's responsive dynamics and even-order harmonic content.^[16] This design draws from classic Fender circuits while incorporating modern refinements for greater versatility in both clean and high-gain applications. In terms of build materials, the Series IV models utilize finger-joined pine cabinets for a lightweight yet resonant enclosure that enhances portability without compromising acoustic projection.^[3] These are covered in black tolex for durability and a classic aesthetic, paired with lightly aged silver grille cloth that evokes vintage Fender styling.^[6] Essential components include a spring reverb tank with long decay characteristics for lush, dripping ambiance, a series effects loop introduced in Series III and refined in IV for seamless integration of time-based pedals post-preamp, and an external speaker jack enabling parallel connection to additional cabinets.^[17]^[18]^[3] The power supply draws 180 watts from standard AC mains, supporting robust operation with higher plate voltages—approximately 475 volts on the DeVille compared to 430 volts on the Hot Rod Deluxe—for expanded headroom and cleaner output at gig volumes.^[19] This elevated voltage, facilitated by larger transformers, allows the DeVille to maintain clarity under heavy drive while reducing early breakup relative to its lower-powered sibling.^[20]

Controls and Channels

The Fender Hot Rod DeVille amplifier features three distinct channels that provide tonal versatility from pristine cleans to high-gain overdrive. The Normal channel delivers a clean tone suitable for articulate rhythm playing or as a foundation for effects pedals, accessed via the front-panel Volume control and an optional Bright switch for enhanced high-frequency response.^[18] The Drive channel introduces moderate overdrive with adjustable gain, offering bluesy crunch or edge-of-breakup tones when the Channel Select button is engaged.^[18] The More Drive mode builds on the Drive channel by increasing gain and sustain for higher compression and lead tones, activated via a dedicated push-button switch that illuminates to indicate engagement.^[18] A shared three-band EQ section—comprising Bass, Middle, and Treble controls—shapes the overall tone across all channels, allowing users to sculpt frequencies before the signal reaches the power section for consistent voicing.^[18] The Master Volume knob governs the overall output level, particularly influencing the Drive and More Drive channels, while channel-specific volume adjustments include the dedicated Volume knob for the Normal channel and the Drive knob, which sets the gain staging for the overdrive channels.^[18] Additionally, the Normal channel benefits from two input jacks: Input 1 for standard guitar sensitivity and Input 2, which provides a -6 dB attenuation for a cleaner boost when using high-output pickups.^[18] Further enhancing usability, the Reverb knob adjusts the level of the amplifier's spring reverb tank, applicable to both channels for added ambiance, with the IV series featuring a smoother reverb circuit for more natural decay.^[18] The Presence control fine-tunes ultra-high frequencies in the power section, providing subtle brightness adjustments post-preamp to refine the amp's top-end sparkle without affecting the core EQ.^[18] For live performance flexibility, a rear-panel 1/4-inch jack accepts a two-button footswitch (model 050419 or equivalent), enabling remote toggling between the Normal and Drive channels as well as activation of More Drive mode, which overrides the front-panel switches when connected.^[18] This setup allows seamless transitions during sets without manual intervention.^[18]

Models and Variants

212 Model

The Fender Hot Rod DeVille 212 Model features an open-back cabinet made from lightweight pine for portability and resonance, with dimensions of approximately 21 inches in height, 24.25 inches in width, and 10.75 inches in depth, weighing around 55 pounds.^[3]^[15] This design provides a wide sound dispersion typical of Fender combos, balancing projection and ease of transport for gigging musicians.^[21] The speaker configuration in the 212 Model has evolved across series to refine its performance. In Series II, it used dual 12-inch Eminence Fender Special Design speakers, offering a versatile response suited to the amp's hot-rodded circuitry.^[22] Series III incorporated Celestion G12P-80 speakers, which emphasize midrange punch for greater definition in overdriven tones.^[23] The current Series IV employs dual Celestion A-Type 12-inch speakers, enhancing overall clarity, bass extension, and smooth highs while maintaining compatibility with the 60-watt output.^[3] This model's tonal profile delivers a balanced full-range sound, with the dual 12-inch speakers providing strong low-end response and ample headroom ideal for larger venues. It produces brighter, more articulate tones than the 410 variant, thanks to the larger speakers' efficiency in handling highs and mids. As the primary configuration since the series' inception, the 212 Model remains in ongoing production with the IV version, serving as a staple for professional and amateur players alike.^[3]

410 Model

The Fender Hot Rod DeVille 410 is a 60-watt tube combo amplifier featuring an open-back cabinet for wide sound dispersion and balanced projection. Measuring approximately 23.5 inches in height, 23.5 inches in width, and 10.75 inches in depth, it weighs around 50 pounds, making it more compact yet heavier than many comparable models due to its robust construction with textured black vinyl covering and a Blackface-style black-and-silver grille cloth.^[25]^[26] Equipped with four 10-inch Eminence speakers featuring a Fender Special Design, each rated at 30 watts and 8 ohms, the 410 configuration delivers a balanced load suitable for switchable 4- or 8-ohm outputs. These speakers remained consistent across both Series II and III versions, providing reliable performance without updates in later iterations. The amp shares the three-channel preamp design common to the Hot Rod DeVille line, offering normal, drive, and more drive modes for versatile gain staging.^[27]^[28] The tonal profile of the 410 emphasizes punchy midrange frequencies and tight bass response, drawing inspiration from classic Fender amplifiers like the Super Reverb and '59 Bassman, which also utilized 4x10 configurations. This setup excels in rock and blues applications, where the four smaller speakers produce focused projection with reduced low-end boom compared to larger configurations, allowing for articulate cleans and responsive overdrive tones at gigging volumes.^[4]^[26] Introduced as part of the Hot Rod series in the mid-1990s, the 410 variant was produced exclusively in Series II (roughly 2000–2010) and Series III (2010–2016), after which it was discontinued in favor of emphasizing the 212 model. No Series IV version of the 410 was ever manufactured, limiting its availability to these earlier production runs.^[28]^[4]

Technical Specifications

Power and Tubes

The Fender Hot Rod DeVille amplifier produces 60 watts into 4 Ω or 2 Ω loads at 5% THD, providing sufficient headroom for live performances and studio applications.^[18] This power rating is achieved through a push-pull configuration in the output stage, ensuring clean tone delivery at moderate volumes and dynamic overdrive when pushed harder.^[3] The power section employs two 6L6 vacuum tubes as the primary power amplifiers, selected for their robust construction and ability to handle high voltages while delivering the characteristic warm, punchy Fender sound.^[3] These tubes operate in a fixed bias arrangement, where the bias voltage can be adjusted internally to optimize performance and tube longevity across different sets of replacements.^[6] In later models, an accessible variable bias control simplifies this process for technicians, allowing precise cathode-to-grid voltage settings without major modifications.^[29] Preamp amplification is handled by three 12AX7 dual-triode tubes, which provide gain staging for the normal, drive, and more drive channels, contributing to the amp's versatile tonal palette from pristine cleans to saturated leads.^[3] The power supply incorporates a solid-state rectifier, which offers reliable voltage regulation and sag-free response compared to traditional tube rectifiers, enhancing overall stability during extended use.^[3]^[30] Electrically, the Hot Rod DeVille is designed for standard North American mains power, operating at 120V AC and drawing approximately 180 watts at full output to support its tube complement without excessive strain on household circuits.^[31] This configuration balances efficiency with the demands of vacuum tube operation, making it suitable for gigging musicians.^[6]

Speaker Configurations

The Fender Hot Rod DeVille 212 model features two 12-inch speakers wired in parallel, presenting a total internal impedance of 4 ohms to the amplifier's output stage.^[3] This configuration allows the 60-watt amplifier to deliver its rated power efficiently, with the option to connect an external 8-ohm cabinet via the extension speaker jack, which parallels with the internal load to approximately 2.67 ohms—within the amp's supported range of 2 or 4 ohms total impedance.^[3]^[32] In contrast, the 410 model, available in Series III, employs four 10-inch speakers, each rated at 8 ohms, wired in a series-parallel arrangement to achieve an 8-ohm internal load.^[25] This setup supports the amplifier's 4 or 8 ohm output capabilities, enabling connection of an additional 8-ohm external cabinet that parallels the internal speakers for a total load of 4 ohms, enhancing system volume and dispersion without exceeding safe operational limits. The 410 configuration was discontinued after Series III.^[25]^[33]^[34] Note that output impedance support varies by series and model: 2 or 4 Ω for Series IV 212, and 4 or 8 Ω for Series III 410. The amplifier's design ensures safe operation with a minimum total load of 2 ohms when using extensions, preventing tube stress or overheating by matching the output transformer's specifications.^[33] The external speaker jack facilitates daisy-chaining compatible cabinets, allowing musicians to expand the system while maintaining impedance balance.^[31] Across models, factory speakers have been upgraded in later series to options like Celestion A-Type 12-inch drivers in the Series IV 212, and Eminence 10-inch in the Series III 410, with sensitivities around 98 dB SPL, which improves overall efficiency and perceived loudness from the 60-watt output by converting more electrical power to acoustic energy.^[35]^[25] These upgrades enhance performance in live settings by providing higher headroom before distortion, though actual output depends on the matched impedance.^[29]

Reception and Use

Critical Reception

The Fender Hot Rod DeVille has been widely praised by audio experts as a reliable workhorse for gigging musicians, offering versatile tones ranging from pristine clean Fender sparkle to bluesy overdrive suitable for live performances. Reviewers highlight its ample headroom and clear articulation, making it an excellent platform for pedals and a staple for working players across genres like blues and classic rock. In a 2018 review of the DeVille IV, MusicRadar commended its rich, clear tones blending 1960s Blackface and 1950s Tweed characteristics, noting the reworked spring reverb provides a smoother, warmer sound with improved note definition and sustain on the drive channel.^[2] Similarly, Guitar.com's 2018 assessment emphasized the amp's tight, punchy response and smooth overdrive, describing it as covering clean, crunch, and solo needs without additional effects, while praising the thick, ambient-friendly reverb.^[36] Criticisms of the Hot Rod DeVille, particularly in earlier models, often center on its high-gain performance and physical build. The drive channel in pre-IV versions has been noted for producing a somewhat ragged or grainy distortion at higher volumes, limiting its appeal for modern high-gain applications. Additionally, the amp's substantial weight—due to its solid pine cabinet and tube-driven design—has been called cumbersome for frequent transport compared to lighter solid-state alternatives. A 2015 MusicRadar review of the DeVille ML 212 acknowledged its strengths as a pedal platform but pointed out its limitations relative to the standard model, along with its heft and higher cost at the time.^[37] The series has earned consistent recognition in professional rankings for its reliability and value, often appearing in "best tube amps" lists under $1,000 street price. Premier Guitar awarded the 2015 DeVille ML 212 a 4.5 out of 5 rating for its vintage-inspired headroom and session-friendly design.^[38] In comparisons to the Hot Rod Deluxe, the DeVille is frequently favored for live settings due to its greater power output (60 watts versus 40 watts) and enhanced low-end punch from dual speakers, providing superior stage volume without sacrificing tonal clarity. Guitar.com's 2018 review leaned toward the DeVille for its bigger, brighter sound and better pedal compatibility in gig environments.^[36]

Notable Users

The Fender Hot Rod DeVille has garnered a dedicated following among prominent guitarists for its robust tone and stage-ready performance, spanning blues, rock, and alternative genres. Blues and rock artist Joe Bonamassa incorporated a Hot Rod DeVille into his recording setup, praising its vintage vibe and dynamic response that "exploded into the mic" during sessions for his album Breakthrough.^[39] In the alternative and indie scene, The Strokes' guitarist Albert Hammond Jr. relied on the 212 model as a core part of his rig for live stage volume and early band recordings, using it on tours supporting albums like Angles and at events including Lollapalooza 2017; several of his personal units were later auctioned for charity.^[40] Session guitarist and solo artist Michael Landau, known for his work with artists like James Taylor and Pink Floyd, influenced the development of the signature Hot Rod DeVille ML 212 edition, which features modifications like a clean boost and variable bias for enhanced headroom and overdrive suited to professional live and studio applications.^[41] Blues guitarist Robben Ford has used the Hot Rod DeVille live, noting its ability to deliver exceptional tone in performance settings.^[42] The amp's three-channel flexibility, combined with its effects loop, has solidified its legacy as a go-to choice for studio recording and continuous use on live tours since the 2000s, powering performances across diverse genres for gigging musicians worldwide.^[1]

References

[1]
From Stage to Studio: The Fender Hot Rod IV Series
Both the Hot Rod DeVille 212 IV and Hot Rod Deluxe IV include a modified overdrive tonality with better note definition.
[2]
Fender Hot Rod DeVille IV review - MusicRadar
Rating 4.0 · Review by Nick GuppyJun 12, 2018 · Aimed at working players at all levels, the price is still affordable and makes the new amp very competitive.
[3]
Hot Rod DeVille™ 212 IV - Fender
Features · 60 watts; Normal, Drive, and More Drive channels · Dual Celestion 12" A-Type speakers · Modified preamp circuitry for increased overdriven note ...Missing: history | Show results with:history
[4]
Fender Announces New Hot Rod III Series Amps - Premier Guitar
Sep 9, 2010 · The Hot Rod DeVille 410 III is a 60-watt combo with a classic 4x10” speaker configuration borrowed from the legendary Super Reverb and '59 ...
[5]
fender® upgrades best-selling tube amps with hot rod series iv ...
Jan 25, 2018 · Both the Hot Rod Deluxe IV and Hot Rod DeVille IV include a modified overdrive tonality with better note definition. Improved bass response ...
[6]
Fender Hot Rod Deville 212 IV 2x12-inch 60-watt Tube Combo Amp
In stock Rating 5.0 (13) Tech Specs · Type: Tube · Number of Channels: 3 · Output Power: 60W · Speaker Size: 2 x 12" Celestion A-Type speakers · Preamp Tubes: 3 x 12AX7 · Power Tubes: 2 x 6L6 ...
[7]
A (brief) history of the Fender Hot Rod Deluxe | 21Hz Backline
Sep 26, 2017 · The Fender Hot Rod Deluxe (HRD condensed) has become Fenders most sold amp since it has been introduced in 1995.
[8]
Taming A Fender Hot Rod Deville - Premier Guitar
Since it's the most readily available, you might first try installing a 12AT7 in the V2 position. This will reduce the gain in the last two stages of the amp ...
[9]
Fender Upgrades Hot Rod Series IV amplifier line
Jan 24, 2018 · Fender Hot Rod amplifier line Today, Fender is officially launching the new, refreshed Hot Rod Series IV, which was first introduced in 1996 ...
[10]
Fender Hot Rod DeVille 3-Channel 60-Watt 4x10" Guitar Combo 1996
In stock Rating 5.0 (4) Estimated Value for Fender Hot Rod DeVille 3-Channel 60-Watt 4x10" Guitar Combo 1996 - 2001 on Reverb
[11]
Hot Rod Deville VS Deluxe circuit not III | Telecaster Guitar Forum
Apr 20, 2013 · The only difference between these 2 boards the higher voltage transformer on the Deville to bump it up the 20 extra watts.Hot Rod Deville vs. Hot Rod Deluxe | Telecaster Guitar ForumHot Rod Deville conversion | Telecaster Guitar ForumMore results from www.tdpri.com
[12]
Fender Hot Rod DeVille Amplifiers | Musician's Friend
4.8 225 · Free delivery · 45-day returnsFender Hot Rod DeVille 212/410 60W (Discontinued) ... Four 10-inch speakers deliver big, bright tone. Don't let the vintage look of the Hot Rod Deville fool you, ...
[13]
Fender Hot Rod DeVille 212 III Guitar Amp - zZounds.com
Rating 5.0 (9) · Free deliveryPlug in and rock out. The Fender Hot Rod DeVille 212 III features a pair of Celestion G12P-80 speakers and a modified tone circuit for better tone than ever.
[14]
Fender Hot Rod Deluxe III 40W 1x12 Tube Guitar Combo Amp Black
1–3 day delivery Free in-store returnsSpecs · Amplifier Type: Tube · Output Power: 40W · Speaker: 1-12" Celestion G12P-80, 8 ohm Speaker · Output Impedance: 4 or 8 ohms · Preamp Tubes: 3 x 12AX7 · Power ...
[15]
Fender Hot Rod DeVille 212 IV 60W 2x12 Tube Guitar Combo Amp ...
The updated aesthetics include a lightweight pine cabinet, improved control panel texture and graphics, ivory pointer knobs, steel-reinforced strap handle and ...Missing: 1996 | Show results with:1996
[16]
The task that nobody asked the breakdown of the hot rod deluxe circuit
Jan 1, 2019 · This topography was introduced in a Fender amp with the 5F6A AND 5F8 Amps. The Fender Pro Sonic brought this topography back into the Fender amp ...
[17]
4EB3C1B, Universal, Stainless Steel, Guitar Amp Reverb Tank
Compatible amps include Fender® Hot Rod Deville, Hot Rod Deluxe, Blues Deluxe (reissue only), Blues Deville (reissue only). Replaces Fender® Part Number ...
[18]
[PDF] HOT ROD DEVILLE™ IV and HOT ROD DELUXE™ IV
PRESENCE:Adjusts tone at a point in the signal path after the preamp circuitry to provide unique ultra high- frequency tone shaping. O. PREAMP OUT/POWER AMP IN: ...
[19]
Fender hot rod deluxe ..180 watts? - My Les Paul Forum
Aug 29, 2017 · Hot Rod DeVille is 60 watts. Two 6L6's would literally melt if you pumped enough voltage into them to get 100wrms, much less 180. HRD and HRDV ...
[20]
Is there a big tonal difference between Fender Hot Rod Deluxe, and ...
Mar 30, 2023 · The big difference is the Deville has larger transformers and higher plate voltages throughout the amp. All in all, the amps sound very much ...Missing: power supply 180 watt
[21]
What's the Difference Between Open-Back and Closed-Back Amp ...
The back is closed, meaning that the sound is more directional because it issues only from the front of the enclosure. A closed-back cabinet lets you aim more ...Missing: Hot Rod DeVille 212
[22]
Speaker Decisions for a Hot Rod DeVille 2x12 - Harmony Central
Feb 4, 2009 · I love how this amp sounds, though I wonder if I would benefit from changing out the stock Eminence designed speakers. I have always been ...<|separator|>
[23]
Fender Hot Rod Deville III 212 - YouTube
Dec 31, 2010 · Buy Now: https://goo.gl/5XTuDb This is the Fender Hot Rod Deville III 212, another revamped amp from the Fender Hot Rod Series.
[24]
Fender Hot Rod Deville 212 IV 2x12-inch 60-watt Tube Combo Amp
In stock Rating 5.0 (13) The clean tone is punchy and clear with a bit of natural tube compression. The classic spring reverb adds nice depth and sounds great. The drive channel is good ...
[25]
Fender Hot Rod DeVille 410 III 60W 4x10 Tube Guitar Combo Amp ...
1–3 day delivery Free in-store returnsThe Fender Hot Rod DeVille 410 III is a 60-Watt guitar amp combo with classic 4 x 10 speaker configuration borrowed from the legendary Super Reverb and '59 ...Missing: dimensions | Show results with:dimensions
[26]
Fender Hot Rod DeVille 410 Guitar Combo Amplifier (60 Watts, 4x10 ...
Rating 5.0 (114) · Free deliveryFender's Hot Rod DeVille 410 sends 60 scorching watts straight into a quartet of 10 in. Fender Special Design Eminence speakers, courtesy of 2 x 6L6 Groove Tube ...
[27]
Fender Hot Rod Deville 410 | Sweetwater
Output: 60 watts into 4 or 8 ohms (Switchable) Speakers: 4-10" Special Design Emminence 8 ohm, 30 watt Speakers Channels: Three Selectable Channels (Normal ...
[28]
Fender Hot Rod DeVille 410 III 60-watt 4x10" Tube Combo Amp
Sorry, the Fender Hot Rod DeVille 410 III 60-watt 4x10" Tube Combo Amp is no longer available. We've left this page up for reference only.
[29]
https://mojotone.com/blogs/fender-field-guide/fender-hot-rod-deville
[30]
[PDF] Fender Hot Rod Deville Manual at AmericanMusical.com
The Hot Rod Deville has three channels, a "More Drive" function, 60W RMS, and a unique input for guitars with active pickups.Missing: history | Show results with:history
[31]
[PDF] Hot Rods Deville 050393-C.qxd - fmicassets.com
Your new Hot Rod™ DeVille/DeVille 212 delivers world–class Fender® tone and world–standard Fender® quality. • 60 watts output into 4Ω or 8Ω (2Ω or 4Ω, DeVille ...
[32]
[PDF] Hot Rods III_079607a.indd - fmicassets.com
The Hot Rod DeVille III is a 60-Watt combo with the classic 2 x 12 speaker configuration borrowed from the legendary Twin Reverb® amp, the bottom end headroom ...
[33]
Celestion A-Type - 12-inch 50W Guitar Speaker
Sensitivity. Nominal diameter. 305mm / 12in. Power rating. 50W. Rated impedance. 8Ω or 16Ω. Sensitivity. 98dB. Chassis type. Pressed steel. Magnet type. Ceramic.Missing: dB | Show results with:dB
[34]
Celestion V-Type - 12 inch 70W Guitar Speaker
Sensitivity. Nominal diameter. 305mm / 12in. Power rating. 70W. Rated impedance. 8Ω or 16Ω. Sensitivity. 98dB. Chassis type. Pressed steel. Magnet type. Ceramic.
[35]
Albert Hammond Jr is selling his Strokes-played Fender DeVille ...
Nov 13, 2018 · Eight amps are set go up for sale on Reverb, including several Fender Hot Rod DeVille combos. “These amps have been played on early Strokes ...