Standard temperature and pressure
Standard temperature and pressure (often abbreviated as STP) is a reference set of conditions used in physical sciences, particularly chemistry and engineering, to standardize measurements of gas properties and volumes for comparability across experiments and datasets. Defined by the International Union of Pure and Applied Chemistry (IUPAC), STP specifies a temperature of exactly 0 °C (273.15 K) and an absolute pressure of 100 kPa (equivalent to 1 bar or 105 Pa).[1] This convention facilitates calculations involving ideal gases, such as determining the molar volume—the volume occupied by one mole of an ideal gas under these conditions, which is approximately 22.711 L/mol according to the IUPAC definition.[2] Prior to 1982, STP was defined using a temperature of 0 °C and a pressure of 1 atm (101.325 kPa), yielding a molar volume of 22.414 L/mol; the update aligned the standard with the International System of Units (SI) by adopting the more precise bar as the pressure unit.[2] Although the pre-1982 definition persists in some older literature and educational contexts, the IUPAC standard is now the internationally recognized benchmark for reporting gas volumes and thermodynamic data.[1] Variations exist for other reference conditions, such as normal temperature and pressure (NTP) at 20 °C (293.15 K) and 101.325 kPa, or standard ambient temperature and pressure (SATP) at 25 °C (298.15 K) and 100 kPa, which are used in specific applications like ambient environmental testing or biological systems.[3] The U.S. National Institute of Standards and Technology (NIST) often employs 20 °C and 101.325 kPa for practical standards in thermophysical property measurements, reflecting real-world calibration needs.[4] These standards ensure consistency in fields ranging from gas law derivations to industrial process design, underscoring STP's role as a foundational concept in scientific standardization.[5]Definitions
Historical Uses
Before 1918, reference conditions for temperature in metric systems were commonly defined as 15 °C (288.15 K) in European metrology and engineering for calibrating length and volume standards to minimize thermal expansion errors in measurements. Standard pressure was often 101.325 kPa (1 atm or 760 mmHg).[6] In the Imperial system prior to 1918, the corresponding standard was 60 °F (15.56 °C) and 1 atm, widely adopted in the United States for documenting gas volumes, such as in the natural gas industry where volumes were reported as standard cubic feet under these conditions.[7] In chemistry, standard temperature and pressure came to be defined as 0 °C (273.15 K) and 1 atm (101.325 kPa) to align with the reproducible freezing point of water, facilitating precise thermometry in gas law experiments and molar volume determinations. This emphasized conceptual consistency in thermodynamic calculations over ambient convenience.[8] The pressure unit of 1 atm, equivalent to 760 torr (mmHg), remained prevalent in vacuum science and gas pressure measurements through the mid-20th century due to the historical reliance on mercury barometers for standardization.[9] These evolutions culminated in the 1982 IUPAC update to 1 bar, marking a transition from atmosphere-based to SI-aligned pressure standards.[10]Current IUPAC STP
The current International Union of Pure and Applied Chemistry (IUPAC) definition of standard temperature and pressure (STP), adopted in 1982, establishes a temperature of 273.15 K (0 °C) and a pressure of 100 kPa, equivalent to 1 bar or exactly $10^5 Pa.[1] This definition reflects a deliberate shift from the pre-1982 standard, which used a pressure of 101.325 kPa (1 atm), to better align with the International System of Units (SI) and facilitate precise calculations in physical chemistry.[10] STP under this definition serves as a reference condition primarily in chemistry for standardizing the reporting of gas volumes and concentrations, particularly in applications involving the ideal gas law, expressed as PV = nRT, where the molar volume V_m of an ideal gas is given by V_m = RT/P.[10] The adoption of 100 kPa simplifies thermodynamic computations by using a round SI-derived value, avoiding the fractional aspects of the former atmospheric pressure standard.[1] This STP specification is detailed in the IUPAC Green Book (Quantities, Units and Symbols in Physical Chemistry, 3rd edition, 2007), which reaffirms the 1982 parameters for reference states in gaseous systems, and remains unchanged in subsequent IUPAC publications as of 2025.[10]Other Standards
International Standard Atmosphere
The International Standard Atmosphere (ISA) defines the atmospheric conditions at mean sea level as a temperature of 15 °C (288.15 K) and a pressure of 101.325 kPa (1013.25 hPa or 1 atm).[11][12] This model provides a hypothetical, static representation of the Earth's atmosphere, assuming dry air and no variability due to weather or location.[13] The ISA was established by the International Civil Aviation Organization (ICAO) in 1954 through Document 7488, building on the 1924 standards set by the International Commission for Aerial Navigation (ICAN).[14][15] These foundational agreements aimed to unify atmospheric references amid post-World War I discrepancies in national models. Subsequent extensions, such as the 1964 ICAO update to 32 km altitude, refined the model while preserving its core sea-level parameters.[12] The primary purpose of the ISA is to standardize aircraft performance calculations, altimetry, and atmospheric modeling in aviation and meteorology, enabling consistent predictions under varying real-world conditions.[11][13] It assumes hydrostatic equilibrium—where atmospheric pressure balances gravitational forces—and ideal gas behavior for air, facilitating reliable engineering designs and flight planning.[16] Unlike the IUPAC standard temperature and pressure, which uses 0 °C for chemical applications, the ISA's 15 °C reflects average global sea-level conditions more relevant to aeronautical use.[17] In the troposphere, the ISA specifies a vertical temperature profile with a constant lapse rate of -6.5 °C/km from sea level up to 11 km altitude, after which temperature stabilizes at -56.5 °C until the tropopause.[13][18] This linear decrease models the typical cooling with elevation in the lower atmosphere. Pressure variation with altitude follows the hydrostatic equation integrated over the temperature profile: P = P_0 \left( \frac{T}{T_0} \right)^{-\frac{g}{\lambda R}}, where P_0 and T_0 are sea-level values, g is gravitational acceleration, \lambda is the lapse rate, and R is the gas constant for air; this form arises from combining the ideal gas law with hydrostatic balance.[19][20]Standard Ambient Temperature and Pressure
Standard Ambient Temperature and Pressure (SATP) refers to the conditions of 298.15 K (25 °C) and 100 kPa (1 bar), as recommended by the International Union of Pure and Applied Chemistry (IUPAC) for reporting thermodynamic properties in physical chemistry.[10] This standard was introduced in the late 20th century, specifically through IUPAC recommendations dating to 1982, to ensure uniformity in data presentation under conditions approximating typical room temperature experiments.[10] It aligns with the SI-unit framework adopted for STP, promoting consistency across scientific measurements while reflecting practical ambient environments. SATP finds primary application in the tabulation of key thermodynamic quantities, including standard enthalpies of formation, Gibbs free energies of reaction, and equilibrium constants, as detailed in chemistry textbooks and reference compilations.[10] These conditions facilitate the comparison of experimental results by standardizing the reference state for substances in gaseous, liquid, or solution phases, emphasizing conceptual reliability over variations in local laboratory setups. Earlier definitions of SATP in some pre-2000s literature employed a pressure of 101.325 kPa (1 atm), but the IUPAC Green Book (3rd edition, 2007) explicitly standardized it to 100 kPa to harmonize with modern pressure units and eliminate discrepancies from the legacy atmospheric standard.[10] Unlike STP, which also uses 100 kPa but specifies 273.15 K (0 °C) for normalizing gas volumes, SATP's elevated temperature better suits thermodynamic evaluations at ambient conditions.[1]Applications
Laboratory Conditions
In laboratory settings, standard conditions for temperature and pressure typically range from 20 °C to 25 °C and 100 kPa to 101.325 kPa, varying by organization and application to ensure consistency in experimental reproducibility. The National Institute of Standards and Technology (NIST) often employs 20 °C and 1 atm (101.325 kPa) for measurements involving gas properties and calibrations, aligning with practical room temperatures for precision work.[3] These conditions facilitate controlled environments without strictly adhering to theoretical ideals like those in STP definitions. Regional variations reflect local standards and SI unit preferences. In the European Union and under International Organization for Standardization (ISO) guidelines, laboratories commonly use 23 °C and 101.325 kPa for conditioning and testing materials, as specified in standards for environmental control. In Australia, particularly in New South Wales educational and industrial contexts, 25 °C and 100 kPa are adopted as standard laboratory conditions to simplify calculations with metric units.[21] These laboratory conditions serve practical purposes such as instrument calibration, fluid density determinations, and simulated environmental testing, where deviations from ideal gas assumptions are acceptable to match real-world scenarios. For instance, the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) specifies 20 °C and 101.325 kPa for HVAC system evaluations in its 2023 guidelines, ensuring reliable performance assessments under typical indoor air densities.[22] Similarly, the U.S. Environmental Protection Agency (EPA) uses 25 °C and 101.3 kPa for ambient air quality monitoring, standardizing pollutant concentration reporting to account for volume corrections at these reference points.[23] This approach prioritizes operational accuracy over universal thermodynamic constants, briefly aligning with broader ambient standards like SATP for certain thermodynamic validations.Molar Volume of Gases
The molar volume V_m of an ideal gas, defined as the volume occupied by one mole of gas, is given by the ideal gas law as V_m = \frac{RT}{P}, where R = 8.314\,462\,618 J/mol·K is the molar gas constant, T is the absolute temperature in kelvin, and P is the pressure in pascals.[24][25] Under current IUPAC STP conditions of 0 °C (273.15 K) and 100 kPa, the molar volume is 22.711 dm³/mol (or 22.711 L/mol).[2] At the historical STP of 0 °C and 101.325 kPa, it is 22.414 dm³/mol (22.414 L/mol).[26] For SATP at 25 °C (298.15 K) and 100 kPa, the molar volume is 24.789 dm³/mol.[27] Under ISA conditions of 15 °C (288.15 K) and 101.325 kPa, it is approximately 23.644 dm³/mol.[24] The difference between the historical and current IUPAC STP molar volumes arises solely from the pressure variation, yielding a conversion factor of approximately 1.01325 (i.e., volumes at 100 kPa are 1.01325 times those at 101.325 kPa for the same temperature).[26] These values assume ideal gas behavior and are essential for converting measured gas volumes to standard conditions in chemical analyses and experiments, enabling consistent comparisons across datasets despite varying laboratory environments.[25]| Standard | Temperature (°C) | Pressure (kPa) | Molar Volume (dm³/mol) |
|---|---|---|---|
| IUPAC STP | 0 | 100 | 22.711 |
| Historical STP | 0 | 101.325 | 22.414 |
| SATP | 25 | 100 | 24.789 |
| ISA | 15 | 101.325 | 23.644 |