Fact-checked by Grok 2 weeks ago

Bandgap voltage reference

A bandgap voltage reference is an electronic circuit designed to produce a fixed, stable output voltage that remains largely independent of temperature, supply voltage, and process variations, typically around 1.25 volts, by leveraging the physics of semiconductor bandgaps in silicon to compensate for thermal effects through the summation of complementary temperature-dependent voltage components.^[1] This reference voltage is fundamental in analog and mixed-signal integrated circuits, serving as a precise benchmark for applications requiring high accuracy, such as analog-to-digital converters (ADCs), digital-to-analog converters (DACs), power management systems, and precision measurement equipment.^[2] The core principle of operation relies on balancing the negative temperature coefficient (CTAT) of the base-emitter voltage (V_BE) of a bipolar junction transistor, which decreases by approximately 2 mV/°C, with the positive temperature coefficient (PTAT) of the difference in base-emitter voltages (ΔV_BE) between two transistors biased at different current densities.^[1] This ΔV_BE is given by (kT/q) ln(N), where k is Boltzmann's constant, T is absolute temperature, q is the electron charge, and N is the ratio of emitter areas or current densities, yielding a PTAT term of about 0.20 mV/°C for a decade ratio at room temperature.^[1] In a typical Brokaw-style bandgap cell, these components are amplified and summed via an operational amplifier and resistor network to produce V_REF = V_BE + K · ΔV_BE, where K is a scaling factor (often around 10–20) chosen to null the net temperature coefficient at approximately 300 K, resulting in an output near 1.25 V based on the extrapolated silicon bandgap voltage of 1.205 V.^[1]^[3] Bandgap references offer key advantages over alternatives like Zener diodes or buried Zener references, including simpler integration in CMOS and bipolar processes, lower power consumption (as low as 50 µA in micropower designs), reduced noise (typically 4–16 ppm RMS wideband), and scalability to higher voltages like 2.5 V or 5 V through amplification.^[2]^[1] Modern implementations achieve temperature coefficients (TCs) as low as 3 ppm/°C and initial accuracies from 0.02% to 1%, making them suitable for systems up to 12-bit resolution, though they may exhibit higher long-term drift (20–50 ppm/√kHr) compared to specialized Zener types.^[2] The concept traces its origins to the early 1960s, with David Hilbiber of Fairchild Semiconductor describing a temperature-stable voltage using diode-connected transistors in a 1964 IEEE paper, followed by Bob Widlar's refinements in 1965 and 1971 that introduced current-density-based PTAT generation and the first commercial IC (LM109).^[3] Paul Brokaw's 1974 IEEE publication established the widely adopted three-terminal bandgap cell topology, which underpins most contemporary designs, including low-dropout variants and sub-1 V extensions for advanced nodes.^[1]^[3]

Fundamentals

Definition and Purpose

A bandgap voltage reference is an electronic circuit designed to produce a fixed output voltage, typically in the range of 1.2–1.3 V, that remains nearly independent of variations in temperature, supply voltage, load current, and manufacturing process parameters.^[1] This stability arises from the circuit's ability to compensate for temperature-induced changes in semiconductor device characteristics, making it a cornerstone of precision analog design.^[2] The primary purpose of a bandgap voltage reference is to serve as a precise and stable voltage source for critical components in electronic systems, including analog-to-digital converters (ADCs), digital-to-analog converters (DACs), voltage regulators, and comparators. In these applications, it ensures accurate signal processing and conversion by providing a consistent benchmark against which other voltages are measured or generated, thereby minimizing errors in data acquisition and power management.^[1] Key performance characteristics include an initial accuracy of 0.5–1.0%, a temperature coefficient of 25–50 ppm/°C, long-term stability on the order of 20–50 ppm/√khr, and a high power supply rejection ratio (PSRR) that effectively filters supply noise. Historically, the design draws from the extrapolated silicon bandgap voltage of approximately 1.205 V at 0 K. The reference voltage is typically about 1.25 V at room temperature, enabling it to mimic this fundamental material property for enhanced thermal invariance.^[1] Compared to alternatives like zener diode references, which suffer from higher noise and poorer temperature stability, bandgap references offer superior performance in integrated circuits; buried zener references provide even better precision but require more complex fabrication.^[2]

Physical Basis

The physical basis of bandgap voltage references stems from the semiconductor bandgap energy, which represents the minimum energy required to excite electrons from the valence band to the conduction band in materials like silicon. In silicon, the bandgap energy E_g is approximately 1.17 eV at 0 K, but for voltage reference purposes, the relevant parameter is the extrapolated bandgap voltage V_g(0) at absolute zero, valued at about 1.205 V.^[4]^[5] This extrapolation accounts for the temperature-dependent narrowing of the bandgap and yields a stable reference voltage near 1.25 V at room temperature (300 K), which is temperature-independent when properly compensated.^[3] The bandgap energy directly influences the forward voltage drop across a p-n junction, V_{BE}, making it the cornerstone for generating precise, stable voltages in integrated circuits.^[6] In a p-n junction under forward bias, V_{BE} is primarily determined by the bandgap energy, as it governs the potential barrier that carriers must overcome for conduction. The temperature dependence of V_{BE} arises from the bandgap's variation with temperature and the intrinsic properties of carrier transport. A key approximation for this dependence is given by the extrapolation formula:

V_{BE}(T) = V_g(0) - \lambda T + \frac{T}{T_0} \left[ V_{BE}(T_0) - V_g(0) + \lambda T_0 \right],

where V_g(0) is the extrapolated bandgap voltage at 0 K, \lambda is the temperature coefficient of the bandgap (approximately $3 \times 10^{-4} K^{-1} for silicon), T is the absolute temperature, and T_0 is a reference temperature (often 300 K).^[7]^[3] This linear model captures the negative temperature coefficient of V_{BE} (typically -1.5 to -2 mV/K), which decreases as temperature rises due to the bandgap narrowing and increased thermal generation of carriers.^[6] The underlying mechanisms involve the Fermi level, intrinsic carrier concentration, and diffusion processes in the p-n junction. In thermal equilibrium, the Fermi level—a measure of the electrochemical potential for electrons—remains constant across the junction, aligning the energy bands between p-type and n-type regions.^[8] The intrinsic carrier concentration n_i, which quantifies thermally generated electron-hole pairs, is given by n_i \propto T^{3/2} \exp(-E_g / 2kT), where k is Boltzmann's constant; this exponential dependence on the bandgap drives the temperature sensitivity of junction currents.^[8] Under forward bias, diffusion dominates as minority carriers (electrons in p-type, holes in n-type) move down concentration gradients across the junction, injecting charge and enabling current flow proportional to \exp(qV_{BE}/kT), where q is the electron charge.^[9] These processes link the bandgap physics to the stable voltage output in references.^[10] Silicon is the predominant material for bandgap voltage references due to its well-characterized bandgap properties, low cost, and compatibility with standard CMOS and bipolar fabrication processes, enabling reliable ~1.25 V outputs.^[11] In contrast, gallium arsenide (GaAs) features a wider bandgap of about 1.42 eV at 300 K, resulting in higher extrapolated reference voltages (around 1.4-1.5 V), but its higher cost and complexity limit it to specialized high-frequency or optoelectronic applications rather than general-purpose references.^[12]^[11]

Principles of Operation

Temperature Dependencies in Semiconductors

The base-emitter voltage V_{BE} of a forward-biased bipolar junction transistor exhibits a negative temperature coefficient, typically around -2 mV/°C at room temperature under constant current density conditions, manifesting as complementary-to-absolute-temperature (CTAT) behavior. This dependence arises primarily from the temperature-induced decrease in the silicon bandgap energy, which reduces the barrier for carrier injection across the pn junction, and from reductions in carrier mobility that diminish the saturation current with increasing temperature.^[13] Bandgap narrowing, particularly in heavily doped emitter regions, further exacerbates this effect by effectively lowering the bandgap and altering the intrinsic carrier concentration.^[13] A key aspect of this temperature dependence involves differences in V_{BE} between transistors operating at different current densities, given by \Delta V_{BE} = \frac{kT}{q} \ln\left(\frac{I_1}{I_2}\right), where k is Boltzmann's constant, T is absolute temperature, q is the electron charge, and I_1, I_2 are the collector currents.^[14] This \Delta V_{BE} term is proportional to absolute temperature (PTAT), providing a positive temperature coefficient of (k/q) \ln(n) \approx 0.2 mV/°C for a typical current density ratio of n=10 in silicon devices.^[14]^[1] The overall temperature behavior of V_{BE} can be approximated as V_{BE}(T) = V_g - \frac{T}{T_r} (V_g - V_{BE}(T_r)) - \alpha T, where V_g is the extrapolated bandgap voltage at $0 K (about $1.205 V for silicon), T_r is a reference temperature, V_{BE}(T_r) is the base-emitter voltage at T_r, and \alpha is an empirical coefficient accounting for linear temperature effects such as mobility variations (typically on the order of $10^{-5} to $10^{-4} V/K).^[15] This model captures the first-order linear decline but overlooks higher-order nonlinearities. Process variations, such as fluctuations in doping levels during fabrication, significantly influence the temperature coefficient of V_{BE}, leading to spreads of up to \pm 24 mV (3\sigma) in \Delta V_{BE} that propagate to errors in the overall temperature coefficient.^[16] Higher emitter doping, for instance, intensifies bandgap narrowing and alters recombination rates, resulting in more negative temperature coefficients and increased variability across devices.^[16] Second-order effects introduce curvature in the V_{BE} versus temperature plot, stemming from nonlinear terms like the temperature dependence of the thermal voltage and logarithmic corrections in the saturation current expression, such as \eta \frac{kT}{q} \ln\left(\frac{T}{T_r}\right), where \eta is a fitting parameter (often around 3-4 for silicon).^[14] These nonlinearities cause residual temperature dependence beyond the linear approximation, typically contributing a curvature of $1-10 \muV/°C², which must be considered for precision applications.^[15]

PTAT and CTAT Components

The proportional-to-absolute-temperature (PTAT) component in a bandgap voltage reference is generated by exploiting the difference in base-emitter voltages (V_{BE}) across two bipolar junction transistors (BJTs) operated at different current densities. Specifically, if one transistor (Q1) carries a collector current I_{C1} = I and the other (Q2) carries I_{C2} = nI where n > 1, the voltage difference is \Delta V_{BE} = V_T \ln(n), with V_T = kT/q being the thermal voltage, k Boltzmann's constant, T the absolute temperature, and q the electron charge. This \Delta V_{BE} is inherently PTAT, increasing linearly with temperature, and is typically developed across a resistor to produce a PTAT current or voltage term. The complementary-to-absolute-temperature (CTAT) component arises directly from the base-emitter voltage V_{BE} of a single BJT, which exhibits a negative temperature coefficient of approximately -1.5 to -2 mV/°C at room temperature due to the temperature dependence of the bandgap energy and carrier concentrations in semiconductors. In the reference circuit, V_{BE} serves as the CTAT term, providing a voltage that decreases with increasing temperature and offsets the positive slope of the PTAT term. To achieve a temperature-independent output, the PTAT and CTAT terms are summed in a weighted manner: V_{REF} = V_{BE} + K \cdot \Delta V_{BE}, where K is a dimensionless scaling factor (often implemented as a resistor ratio R_2 / R_1). The value of K is selected to null the first-order temperature coefficient, such that dV_{REF}/dT \approx 0, given by K \approx (V_G - V_{BE}) / (\Delta V_{BE}) at a reference temperature, where V_G is the extrapolated silicon bandgap voltage at 0 K (approximately 1.205 V). This cancellation balances the negative CTAT slope against the positive PTAT slope. The resulting reference voltage stabilizes near the silicon bandgap voltage, derived as V_{REF} \approx V_G + (T / T_r) (V_{BE}(T_r) - V_G), where T_r is the reference temperature; for silicon processes, this yields V_{REF} \approx 1.25 V with residual higher-order curvature. In basic implementations, operational amplifiers are employed to ensure equal collector currents in the PTAT-generating transistors via feedback (current mirroring) and to amplify or buffer the summed voltage for output stability without loading effects. A key limitation of this first-order approach is the minimum supply voltage required, typically around 1.4 V, arising from the need to support V_{BE} (≈0.7 V) plus the saturation voltage V_{sat} (≈0.2-0.3 V) of current sources or the operational amplifier output stage.^[17]

Circuit Designs

Brokaw Cell Topology

The Brokaw cell topology, introduced in 1974, represents a foundational design for bandgap voltage references using an operational amplifier to ensure balanced currents through two bipolar junction transistors (BJTs). In the classic schematic, two BJTs, Q1 and Q2, have their collectors connected through resistors to the power supply, with the collector nodes connected to the inputs of the operational amplifier, while their bases are driven by the output of the operational amplifier. The emitters of Q1 and Q2 are interconnected through a resistor R (often denoted as R1), creating a difference in base-emitter voltages (ΔV_BE) across this resistor due to differing current densities—typically achieved by making Q2's emitter area larger than Q1's (e.g., 8:1 or 10:1 ratio). Feedback is provided by two equal resistors (often labeled R2 for symmetry) connected from the amplifier's output to the bases of Q1 and Q2, which sets the gain for the PTAT term and, through the opamp action, ensures the amplifier inputs (at the collectors) are at the same potential, forcing equal collector currents in Q1 and Q2.^[18]^[19] Operationally, the circuit generates a proportional-to-absolute-temperature (PTAT) current through resistor R, given by I_PTAT = ΔV_BE / R, where ΔV_BE arises from the logarithmic difference in current densities between Q1 and Q2. This PTAT current is mirrored and combined with the complementary-to-absolute-temperature (CTAT) component from the base-emitter voltage V_BE of Q1, producing a temperature-compensated output at the amplifier's output node. The key output voltage equation is:

V_{OUT} = 2 V_{BE} + \left( \frac{2 R_2}{R_1} \right) \Delta V_{BE}

where the resistor ratio (2 R2 / R1) is tuned such that the positive temperature coefficient of the ΔV_BE term cancels the negative coefficient of the V_BE terms, yielding a flat response near the silicon bandgap voltage of approximately 1.22 V extrapolated to 0 K, often resulting in an output around 1.25 V. The PTAT and CTAT principles ensure this compensation without requiring additional circuitry for basic operation.^[18]^[19] This topology offers several advantages, including simplicity with a low component count (typically seven transistors including mirrors), low power consumption, and good power supply rejection ratio (PSRR) due to the feedback loop. Typical temperature coefficients (tempco) achieved are less than 50 ppm/°C over wide ranges like -55°C to +125°C, with residual drifts as low as 2-4 ppm/°C using matched thin-film resistors. However, it requires a bipolar process for the BJTs, as standard CMOS lacks high-quality vertical bipolars, and includes drawbacks such as the need for startup circuitry (e.g., a transient current source like a FET) to prevent the circuit from latching into a zero-current stable state. Variations include implementations using PNP BJTs for low-voltage operation in CMOS processes with parasitic bipolars or added bipolar layers, or NPN configurations for higher performance, adapting the design to integrated circuit constraints while maintaining the core feedback structure.^[18]^[19]

Widlar and Alternative Topologies

The Widlar bandgap voltage reference, introduced by Robert Widlar in 1971, employs a current-mirror configuration with bipolar junction transistors (BJTs) and resistors placed in the emitter paths to generate both proportional-to-absolute-temperature (PTAT) and complementary-to-absolute-temperature (CTAT) components. In this topology, two BJTs (Q1 and Q2) are biased with equal collector currents via a current mirror, but Q1 includes an emitter resistor R that creates a voltage difference ΔV_BE across it, serving as the PTAT term derived from the thermal voltage V_T and the emitter area ratio n between Q2 and Q1. The CTAT component comes from the base-emitter voltage V_BE of a third transistor Q3, which sums with the amplified PTAT voltage at the output node through additional resistors R1 and R2 to produce a temperature-stable reference voltage near the silicon bandgap of 1.205 V.^[20]^[1] The output voltage for the Widlar topology is given by:

V_{REF} = V_{BE} \left(1 + \frac{2R_2}{R_1}\right) + \frac{R_2}{R} V_T \ln(n)

where V_BE is the CTAT base-emitter voltage (approximately -2 mV/°C), V_T is the thermal voltage (kT/q, approximately +0.086 mV/°C at room temperature), and the resistor ratios and ln(n) term set the PTAT slope to cancel the CTAT nonlinearity, yielding minimal temperature coefficient when optimized.^[20]^[21] Compared to the Brokaw cell, which relies on a voltage-feedback loop with an operational amplifier, the Widlar design offers advantages in low-power applications due to its current-mode operation, enabling smaller quiescent currents (often in the microamp range) and suitability for single-supply voltages as low as 2 V without requiring a high-gain amplifier. It also facilitates easier integration in CMOS processes by leveraging parasitic vertical PNP BJTs for the PTAT generation, reducing the need for specialized bipolar fabrication.^[1]^[20] Alternative topologies to the Widlar design include exponential current references that utilize logarithmic amplifiers to extract PTAT currents from transistor V_BE differences, converting them via anti-log stages to form the reference voltage, which can improve linearity in certain sensor-integrated circuits. Another variation involves resistorless designs employing switched-capacitor techniques for PTAT voltage generation, where capacitors charge to ΔV_BE during clock phases and transfer the charge to mimic resistor division, eliminating resistor-matching issues and thermal noise while enabling sub-1 V operation in deep-submicron CMOS.^[22] In comparison to the Brokaw topology, the Widlar circuit exhibits higher output impedance (typically >1 MΩ), making it more ideal as a current source reference, though it is susceptible to offset voltages from current-mirror mismatches and resistor tolerances, potentially requiring laser trimming for precision below 0.1%. Implementation challenges include ensuring accurate resistor ratios (e.g., 10:1 for optimal TC cancellation) and area scaling for ln(n), as mismatches can introduce temperature drift up to 50 ppm/°C without calibration; additionally, resistor thermal noise contributes to output ripple, often mitigated by filtering.^[1]^[21] This topology found early application in 1970s integrated circuits, such as National Semiconductor's LM109 voltage regulator and LM194 precision current source, where it provided stable referencing for op-amp biasing and regulator feedback loops in low-power analog systems.^[20]

Advanced Implementations

Low-Voltage and Sub-Bandgap References

Sub-bandgap voltage references achieve output voltages below the conventional 1.25 V silicon bandgap by adjusting the weighting factors in the summation of the complementary-to-absolute-temperature (CTAT) base-emitter voltage V_{BE} and the proportional-to-absolute-temperature (PTAT) difference \Delta V_{BE}. The reference voltage is given by V_{REF} = \alpha V_{BE} + \beta \Delta V_{BE}, where \alpha < 1 and \beta > 1 to yield V_{REF} in the range of approximately 0.5–1.0 V.^[23] This approach modifies the standard PTAT/CTAT balance to prioritize lower output while maintaining temperature stability. Several techniques enable low-voltage operation below 1.25 V to meet the demands of modern low-power integrated circuits. Current-mode summation converts the PTAT and CTAT voltages into currents, which are then combined and mirrored to generate the reference, allowing operation with reduced supply headroom.^[24] Resistive division scales down the traditional bandgap output using a resistor network, as pioneered in early sub-1 V designs, though it introduces sensitivity to resistor matching. Switched-capacitor techniques discretize the summation process to avoid continuous-time limitations, facilitating operation in deep-submicron processes with minimal static power.^[25] These methods face significant challenges in CMOS technologies, including reduced headroom for transistor stacking, which limits minimum supply voltage to around 0.9 V in 0.18 μm processes due to threshold voltage drops.^[26] Additionally, altering the PTAT/CTAT weights exacerbates nonlinear curvature in the temperature dependence, increasing the temperature coefficient compared to standard references.^[27] Representative examples include piecewise linear approximation, which segments the temperature curve for targeted compensation in sub-bandgap designs, and beta-multiplier references adapted for Internet of Things (IoT) devices, achieving quiescent currents below 1 μA while delivering stable low voltages.^[28]^[29] Post-2012 advancements have focused on nano-power implementations in advanced nodes, such as 28 nm CMOS, realizing 0.6 V outputs with temperature coefficients around 10 ppm/°C and supply voltages as low as 0.6 V for ultra-low-power applications.^[30]

Curvature Compensation and High-Precision Techniques

The nonlinear temperature dependence of the base-emitter voltage V_{BE}(T) in bipolar junction transistors introduces curvature in bandgap references, primarily arising from quadratic and higher-order terms such as T \ln T that deviate from the ideal linear complementary-to-absolute-temperature (CTAT) behavior after first-order compensation.^[31] These terms, which become prominent over wide temperature ranges, result in residual temperature coefficients (tempcos) on the order of 10-50 ppm/°C without further correction.^[32] Curvature compensation techniques address these nonlinearities through higher-order cancellation methods. Piecewise linear compensation employs resistor networks or switched segments to approximate the curvature with linear segments tailored to different temperature ranges, effectively reducing tempco to below 5 ppm/°C in CMOS implementations.^[33] Exponential CTAT generation leverages the nonlinear current gain \beta of bipolar transistors to produce a compensation current with an exponential temperature profile that counters the V_{BE} curvature, achieving sub-3 ppm/°C performance in trimmable designs.^[34] Dynamic element matching, often integrated with these approaches, randomizes mismatch errors in current mirrors to suppress low-frequency noise contributions to curvature.^[35] High-precision enhancements further minimize errors beyond curvature correction. Chopping stabilization modulates the operational amplifier in the reference circuit at a high frequency to shift 1/f noise to higher frequencies, where it can be filtered, enabling tempcos as low as 1 ppm/°C while maintaining low power.^[36] Laser trimming adjusts resistor values post-fabrication to achieve initial output accuracy below 0.1%, compensating for process variations in CTAT and PTAT ratios.^[37] Digital calibration, common in system-on-chip (SoC) integrations, uses on-chip logic to periodically adjust the reference based on embedded sensors, supporting tempcos under 2 ppm/°C across industrial ranges. These techniques enable bandgap references with tempcos below 2 ppm/°C over -40°C to +125°C. For instance, the ADR4550 achieves a maximum tempco of 2 ppm/°C through laser-trimmed curvature compensation and low-noise amplification.^[38] Similarly, the LT6657 delivers 1.5 ppm/°C drift via chopping and precise PTAT/CTAT balancing.^[39] Post-2012 evolutions have extended these methods to advanced nodes. All-MOS designs utilizing parasitic vertical PNP bipolar transistors in standard CMOS processes have realized tempcos of 0.5 ppm/°C by exploiting MOS weak-inversion characteristics for PTAT generation alongside curvature correction.^[40] In FinFET technologies at 7 nm nodes, bandgap references incorporate programmable compensation and reduced parasitics to maintain tempcos around 6 ppm/°C, supporting high-density integration in low-power SoCs.^[41]

Applications

Role in Analog Integrated Circuits

Bandgap voltage references play a critical role in analog integrated circuits by providing a stable, temperature-independent voltage source essential for precision operations. In analog-to-digital converters (ADCs) and digital-to-analog converters (DACs), they serve as the reference voltage for accurate signal conversion, ensuring consistent thresholds across varying environmental conditions. For instance, in successive approximation register (SAR) ADCs achieving 16-bit or higher resolution, the bandgap reference maintains the full-scale range with minimal drift, enabling effective number of bits (ENOB) close to the theoretical maximum by compensating for thermal variations in semiconductor parameters.^[42]^[43] In operational amplifiers (op-amps) and comparators, bandgap references establish precise bias levels and threshold voltages, contributing to temperature-stable performance in feedback loops and decision-making circuits. A representative example is the LM317 adjustable voltage regulator, where an internal bandgap reference generates a nominal 1.25 V output that remains stable over a wide temperature range, allowing the regulator to deliver adjustable outputs with low thermal coefficients.^[5] This stability is vital for maintaining gain accuracy and offset in op-amp-based analog signal chains. On-chip integration of bandgap references in mixed-signal system-on-chips (SoCs), such as those in STM32 microcontrollers, enables compact, self-contained precision without external components.^[44] Noise management is a key aspect, with flicker (1/f) noise in bandgap circuits often mitigated through capacitor-based filtering to achieve integrated noise densities below 1 μV rms in low-frequency bands (e.g., 0.1–10 Hz), preserving signal integrity in sensitive analog blocks.^[45] Practical implementations highlight these roles; the TL431 shunt reference, leveraging a bandgap core, is widely used in switch-mode power supply feedback loops within analog ICs to regulate output voltages with high precision and low temperature coefficient. Similarly, the MAX6009 provides a low-power (1 μA quiescent current) bandgap-derived 2.5 V reference suited for battery-operated analog circuits, such as portable sensor interfaces, where space and energy constraints demand minimal footprint and dissipation.^[46]^[47]

Use in Power Management and Sensors

Bandgap voltage references are integral to voltage regulators, where they provide a stable reference voltage for feedback loops to ensure output stability across wide temperature ranges. In linear regulators like the 78xx series and low-dropout (LDO) regulators, the bandgap reference maintains precise regulation by compensating for thermal variations, typically operating reliably from -40°C to 125°C.^[48] For instance, in LDO designs such as those based on curvature-compensated circuits, the reference achieves a temperature drift of 8.11 ppm/°C with input voltages from 3 V to 5 V, enabling consistent performance in power supply circuits.^[49] In battery management systems (BMS) for lithium-ion batteries, particularly in electric vehicles (EVs), bandgap references deliver temperature-compensated voltage thresholds for monitoring charge and discharge cycles, preventing overvoltage or undervoltage conditions. Devices like the Renesas ISL78600 multi-cell Li-ion battery manager employ precision bandgap references to achieve cell reading errors as low as 1.2 mV over a decade of operation, factoring in thermal stresses.^[50] High-precision implementations, such as current-mode bandgap circuits fabricated in 180 nm CMOS, offer a temperature coefficient of 2.69 ppm/°C over -40°C to 125°C, supporting accurate voltage monitoring in EV battery packs with line sensitivity of 42 ppm/V.^[51] For sensor applications, bandgap references serve as stable baselines for signal conditioning and conversion. In PTAT-based temperature sensors, the reference combines with proportional-to-absolute-temperature elements to generate accurate outputs, with series resistance compensation reducing non-linearity to 0.44 ppm/°C from 0°C to 85°C.^[52] Similarly, in readout circuits for resistive transducers like pressure sensors, bandgap-derived references ensure precise ratiometric measurements, as demonstrated in CMOS designs achieving low noise and high linearity.^[53] In automotive and industrial environments, AEC-Q100 qualified bandgap references withstand harsh conditions including vibration, electromagnetic compatibility (EMC) issues, and elevated temperatures up to 150°C. For example, the Texas Instruments LM61440-Q1 synchronous buck converter integrates a bandgap reference for regulation, qualified under AEC-Q100 Grade 1 with junction temperatures to 150°C, supporting automotive power distribution.^[54] The Infineon TLS835B2ELV linear regulator similarly uses an internal bandgap-based voltage reference, operating from -40°C to 150°C while meeting AEC-Q100 standards for reliability in vibration-prone settings.^[55] Recent evolutions in low-power bandgap references cater to wearables and Internet of Things (IoT) devices, enabling always-on sensing with quiescent currents below 1 μA. Ultralow-power CMOS designs, such as those using N+-doped PMOS transistors in 0.18 μm processes, consume about 50 nA at 1.5 V supply while maintaining a temperature coefficient of 75 ppm/°C over -40°C to 85°C, ideal for battery-constrained applications like 2020s smartwatches.^[56] These references often incorporate low-voltage techniques to operate below 1 V, further extending battery life in portable sensor nodes.^[57]

History and Development

Early Concepts and Inventions

The roots of bandgap voltage references trace back to the limitations of early semiconductor voltage references in the 1950s, when Zener diodes emerged as the primary discrete devices for providing stable voltages through reverse breakdown mechanisms. Invented based on Clarence Zener's 1934 theory of avalanche breakdown and practically realized in silicon by the late 1950s, these diodes offered breakdown voltages around 5-7 V with reasonable stability but exhibited significant temperature dependence, typically with coefficients of ±1 to ±2 mV/°C that varied by operating voltage, making them unsuitable for precision applications over wide temperature ranges.^[58]^[59] This instability spurred exploration into fundamental semiconductor physics, particularly the temperature behavior of p-n junctions as described in William Shockley's 1949 theory of p-n junctions, which derived the diode equation V = \frac{kT}{q} \ln \left( \frac{I}{I_S} \right), revealing the base-emitter voltage V_{BE} in bipolar transistors decreases by about -2 mV/°C due to the temperature-sensitive saturation current I_S. Early experimental data from Bell Laboratories, documented in 1950s transistor handbooks and reports, quantified V_{BE} variations across temperatures, highlighting its complementary-to-absolute-temperature (CTAT) characteristic relative to the silicon bandgap energy E_g \approx 1.12 eV, which increases slightly with decreasing temperature and inspired ideas for combining CTAT and proportional-to-absolute-temperature (PTAT) effects to cancel thermal drifts.^[60]^[61] In the early 1960s, as monolithic integrated circuits gained traction, Robert Widlar at Fairchild Semiconductor pioneered temperature-stable biasing circuits for operational amplifiers, notably in the μA702 released in 1964, where he employed current mirrors and resistor ratios to generate PTAT voltage differences that partially compensated V_{BE} drifts, achieving improved thermal performance over discrete Zener-based designs without yet forming a full bandgap reference.^[6] These efforts built directly on the extrapolated insights from V_{BE} measurements, setting the stage for integrated temperature-independent references. The conceptual breakthrough occurred in 1964 when David Hilbiber, also at Fairchild, proposed the first bandgap voltage reference in his ISSCC presentation, summing a PTAT term—derived from the \Delta V_{BE} between two bipolar transistors operated at different current densities—with a CTAT V_{BE} to produce an output near the extrapolated bandgap voltage of 1.22 V at 0 K, resulting in a circuit with a temperature coefficient below 10 ppm/°C. This innovation marked the shift toward fully integrated solutions, with Widlar implementing the first commercial bandgap in National Semiconductor's LM113 voltage regulator in 1971 and incorporating similar references into linear ICs like the LM10 op-amp shortly thereafter, enabling compact, on-chip precision biasing in analog systems.^[5]

Key Patents and Modern Evolutions

The foundational patent for the bandgap voltage reference was US3271660, granted in 1966 to David F. Hilbiber, which described a basic circuit combining a proportional-to-absolute-temperature (PTAT) voltage from differently biased diodes and a complementary-to-absolute-temperature (CTAT) base-emitter voltage to achieve temperature stability. A practical integrated circuit implementation followed with US3617859 in 1971, issued to Robert C. Dobkin and Robert J. Widlar, introducing a regulator with a zero-temperature-coefficient reference suitable for monolithic fabrication.^[62] Further refinement came in US4249122 (1981) by Widlar, which enhanced low-power operation through optimized current mirroring and resistor scaling for integrated circuits.^[63] Dobkin advanced precision with US4447784 (1984), incorporating nonlinear curvature compensation to minimize second-order temperature errors in the reference output.^[64] In the post-1980s era, bandgap designs evolved toward CMOS compatibility, particularly in the 1990s, enabling cost-effective integration in standard digital processes without bipolar transistors, as exemplified by National Semiconductor's developments in low-voltage references for mixed-signal ICs. The 2000s saw sub-1 V references emerge to support scaled supply voltages, with Malcovati et al. demonstrating a curvature-compensated BiCMOS bandgap operating at 1 V supply, achieving 5 ppm/°C temperature coefficient and 0.54 V output.^[65] Modern evolutions from 2012 to 2025 emphasize nano-power consumption for 5G and IoT applications, including sub-1 V designs in advanced nodes. Adaptive trimming techniques have improved accuracy, such as auto-trimming circuits achieving 9.99 ppm/°C over -40°C to 125°C with 54 µW consumption for AIoT chips.^[66] Industry milestones include Analog Devices' ADR45xx series in the 2010s, offering <1 ppm/°C temperature coefficient and ±0.02% initial accuracy for precision data acquisition.^[67] Texas Instruments' REF50xx family, updated in the 2020s for automotive use, provides 3 ppm/°C drift and AEC-Q100 qualification for harsh environments.^[68] To address high-voltage gaps in silicon-based designs, recent shifts incorporate wide-bandgap materials like SiC and GaN; a 4H-SiC voltage reference supports depletion-mode GaN circuits up to 200°C, reducing thermal limitations in power electronics.^[69]

References

[1]
[PDF] MT-087 Tutorial, Voltage References - Analog Devices
The bandgap cell reference voltage VZ appears at the base of Q1, and is the sum of VBE (Q1) and. V1, or 1.205 V, the bandgap voltage: 1. BE(Q1). Z. V. V. V. +.
[2]
AN-82: Understanding and Applying Voltage References
Today's IC reference technology is divided along two lines: bandgap references, which balance the temperature coefficient of a forward-biased diode junction ...
[3]
[PDF] The Bandgap Reference
Sep 2, 2016 · In 1965, Widlar, from the same com- pany, more explicitly showed that the base-emitter voltages of two transis- tors biased at different current ...<|control11|><|separator|>
[4]
https://hyperphysics.phy-astr.gsu.edu/hbase/Tables/Semgap.html
[5]
Bandgap Voltage References - Power Electronics News
Sep 1, 2021 · Vg0 is the extrapolated energy bandgap voltage of the semiconductor material at absolute zero (i.e. 1.205 V); q is the electron charge ...Missing: Hilbiber | Show results with:Hilbiber
[6]
Introduction to Bandgap Voltage References - Technical Articles
Jul 7, 2019 · The goal of a voltage reference is to generate a stable voltage that is ideally independent of changes in temperature and other external factors ...Missing: characteristics | Show results with:characteristics
[7]
[PDF] Device Physics - MIT
1.6 VBE Temperature Dependence. We are interested in finding the temperature dependence of VBE for constant IC [4]. Solving the diode equation for VBE. VBE =.
[8]
Intrinsic Carrier Concentration - PVEducation
A large band gap will make it more difficult for a carrier to be thermally excited across the band gap, and therefore the intrinsic carrier concentration is ...
[9]
Bias of PN Junctions - PVEducation
Carrier Injection and Forward Bias Current Flow. The increased diffusion from one side of the junction to the other causes minority carrier injection at the ...
[10]
PN Junction Theory for Semiconductor Diodes - Electronics Tutorials
This charge transfer of electrons and holes across the PN junction is known as diffusion. ... A suitable positive voltage (forward bias) applied between the two ...
[11]
Bandgap Voltage Reference Circuit Design and Usage
A bandgap reference voltage is a voltage source that outputs a voltage proportional to the bandgap of a semiconductor.Missing: characteristics | Show results with:characteristics
[12]
Gallium Arsenide vs. Silicon
Both discrete components and integrated circuits made in GaAs are faster than those made of silicon because its low-field electron mobility is larger than that ...
[13]
[PDF] A study of the temperature dependence of the DC current-voltage ...
Oct 16, 1989 · (BJT) has a negative temperature coefficient, i.e.. V. BE ... T). (3.10). The high doping causes bandgap narrowing in the emitter. J.
[14]
[PDF] LECTURE 390 – BANDGAP VOLTAGE REFERENCE
VGO = bandgap voltage of silicon (1.205V). NA = acceptor impurity concentration. Page 4. Lecture 390 – Bandgap Voltage References (12/6/01). Page 390-4. ECE ...Missing: Hilbiber | Show results with:Hilbiber
[15]
https://ieeexplore.ieee.org/document/1051368
[16]
[PDF] Predicting and Designing for the Impact of Process Variations and ...
These variations lead to errors in the reference voltage and significantly impact manufacturing cost by increasing trimming requirements and decreasing yield.
[17]
[PDF] Low Voltage, Low Power CMOS Bandgap References
The first bandgap reference was proposed by Robert Widlar in 1971 [1]. It used conventional junction isolated bipolar technology to make a stable low voltage ( ...
[18]
[PDF] A simple three-terminal IC bandgap reference - Iowa State University
bandgap voltage is described, The new two-transistor circuit uses collector current sensing to eliminate errors due to base current.
[19]
The Brokaw Cell | Bandgap References | Electronics Textbook
Four years after Widlar developed his bandgap voltage reference circuit, Paul Brokaw published a paper entitled A Simple Three-Terminal IC Bandgap Reference.
[20]
New developments in IC voltage regulators
Insufficient relevant content. The provided content (title and metadata) does not contain specific details about the silicon bandgap voltage, such as 1.205 V at 0K or extrapolation to room temperature. It only mentions "New developments in IC voltage regulators" without further elaboration.
[21]
Chapter 14: Voltage References - Analog Devices Wiki
Jun 6, 2017 · The bandgap reference technique is attractive in IC designs because of several reasons; among these are the relative simplicity, and the ...
[22]
Resistorless switched-capacitor bandgap voltage reference with low ...
A novel switched-capacitor bandgap voltage reference circuit is presented that dispenses entirely with the use of resistors. Since capacitors are used ...
[23]
[PDF] A sub 1V bandgap reference circuit
Sep 8, 2006 · The first bandgap reference was proposed by Robert Widlar in 1971 [2] as shown in Figure. 1.3 below. It used conventional junction isolated ...
[24]
Design of low-voltage bandgap reference using transimpedance ...
Aug 7, 2025 · For the low voltage bandgap reference design many approaches have been proposed; resistive divider networks [7][8][9], current summing and a ...
[25]
[PDF] low-voltage low-power analog circuit techniques
limitations of low-voltage bandgap reference circuits. Page 39. 32. 2.4 Low ... These include current-mode techniques, switched-capacitor analog filters ...
[26]
(PDF) 0.9 V, 5 nW, 9 ppm/°C Resistorless Sub-Bandgap Voltage ...
The analytical behavior of the circuit is described, and simulation results for a standard 0.18 μm CMOS process are analysed. A reference voltage of 479 mV is ...
[27]
[PDF] The Design of a Low-Voltage Bandgap Reference [The Analog Mind]
Nov 30, 2021 · Most integrated circuits incorporate bandgap references (often simply called bandgaps) to define certain dc voltages or currents that serve ...
[28]
[PDF] A 1.1 V Current-Mode and Piecewise-Linear Curvature Corrected ...
A low voltage, micro-power, curvature-corrected bandgap reference is presented that is capable of working down to input voltages of 1.1 V in a relatively ...Missing: approximation | Show results with:approximation
[29]
A novel precision CMOS current reference for IoT systems
Aug 9, 2025 · This paper presents a low-voltage and low-power CMOS precision current reference circuit, which leads to high current stability to ...
[30]
Low-power, wide supply voltage bandgap reference circuit in 28nm ...
This paper presents a CMOS reference circuit which can work properly under the near-threshold voltage of 0.6V. It is based on the temperature characteristic of ...
[31]
[PDF] Toward Fully Curvature-Corrected Bandgap Reference Circuits
Abstract—We present a novel BiCMOS-based temperature compensation technique aiming at complete correction of the curvature in the temperature response of ...
[32]
A Bandgap Reference Circuit with 2nd Order Curvature Correction
[9]. Gunawan M, Meijer G C M, Fonderie J, et al., “A curvature-corrected low-voltage bandgap voltage reference”. IEEE. J.Solid-State Circuits, vol 6, Jun ...
[33]
Piecewise linear curvature-compensated CMOS bandgap reference
A low-voltage low-power bandgap voltage reference without using passive components is presented. Using piecewise linear curvature-compensated scheme, ...
[34]
Trimmable bandgap reference circuit with exponential curvature ...
This paper proposes an improved exponential curvature-compensated bandgap reference circuit to exploit the exponential relationship between the current gain ...
[35]
Curvature-Compensated Bandgap Voltage Reference
The proposed BGR provides a stable reference voltage at 1.25 V with a low TC and strong power supply rejection (PSR).
[36]
A High-Precision Bandgap Reference with Chopper Stabilization ...
Dec 29, 2023 · The bandgap reference comprises start-up circuit, IPTAT generation circuit with chopper-operational amplifier, a bias circuit, operational ...
[37]
What is voltage trimming in bandgap references?
Mar 14, 2019 · Trimming adjusts the resistors and hence the current back to design intent. The reference gets back to the desired voltage output and temperature performance.
[38]
ADR4550 Datasheet and Product Info - Analog Devices
0.8 ppm/°C (D grade 0°C to 70°C) · 1 ppm/°C (C grade 0°C to 70°C) · 2 ppm/°C (B grade −40°C to +125°C) · 4 ppm/°C (A grade −40°C to +125°C).Missing: tempco | Show results with:tempco
[39]
[PDF] LT6657 – 1.5ppm/°C Drift, Low Noise, Buffered Reference
The LT6657 is a precision voltage reference with 1.5ppm/°C drift, 0.5ppmP-P noise, 0.1% initial accuracy, and a wide supply range up to 40V.Missing: tempco | Show results with:tempco
[40]
A 1.2 v supply 0.58 ppm/°C CMOS bandgap voltage reference
Aug 7, 2025 · A precision curvature-compensated bandgap reference (BGR) is proposed and implemented using a standard 0.18-μm CMOS process.
[41]
BJT Based Precision Voltage Reference in FinFET Technology
This work addresses the problem of realizing high-precision voltage references in deep nanoscale FinFET process technology.
[42]
[PDF] MAX11167 16-Bit, 250ksps, ±5V SAR ADC with Internal Reference ...
The MAX11167 features an internal bandgap reference circuit (VREFIO = 4.096V) that is buffered with an internal reference buffer that drives the REF pin. The ...
[43]
Fast 16-Bit 1.5 Msps/Channel Octal Simultaneous Sampling SAR ...
Jan 9, 2017 · The LTC2320-16 integrates a precision bandgap reference with low drift and guaranteed 20ppm/ºC maximum temperature coefficient into a small ...
[44]
Basics of power supply design for MCU - stm32mcu - ST wiki
In this case, VDDA is more sensitive to noise and accuracy. Some products embed an internal bandgap reference VREFBUF which can provide a steady voltage ...
[45]
A 0.82 μVrms ultralow 1/f noise bandgap reference for a MEMS ...
Apr 17, 2023 · This paper proposes an ultralow 1/f noise BGR by removing the error amplifier and applying an optimized circuit topology.
[46]
[PDF] The TL431 in the Control of Switching Power Supplies - onsemi
TL431 – Small-Signal Analysis. ❑ The TL431 is an open-collector op amp with a reference voltage. ❑ Neglecting the LED dynamic resistance, we have: LED. R.
[47]
[PDF] MAX6006–MAX6009 - 1µA SOT23 Precision Shunt Voltage Reference
The MAX6006–MAX6009 ultra-low-power shunt references are ideal for space-critical and low-power applications. They are offered in 3-pin SOT23 packages, and ...
[48]
[PDF] SECTION 2 REFERENCES AND LOW DROPOUT LINEAR ...
The nominal bandgap reference voltage of 1.225V is then the sum of Q1's VBE and V1. The AD1580 is designed to operate at currents as low as 50 µA, also handling ...
[49]
Design of LDO circuit based on curvature compensation reference ...
Jan 6, 2023 · The temperature drift coefficient of the bandgap circuit is 8.11 ppm/°C, the input voltage is 3–5 V, the output voltage is 2.8 V, and the linear ...<|separator|>
[50]
https://www.renesas.com/us/en/document/whp/optimizing-battery-accuracy-evs-and-hevs
[51]
A 2.69 ppm/°C bandgap reference with 42 ppm/V line sensitivity for ...
Apr 30, 2025 · This paper introduces a high-precision bandgap reference (BGR) designed for battery management systems (BMS), featuring an ultra-low temperature coefficient ( ...
[52]
Series Resistance Compensation in PTAT Temperature Sensors ...
Aug 6, 2025 · Proportional-to-absolute-temperature (PTAT) temperature sensors and bandgap reference circuits using diodes have been also proposed.Missing: transducers | Show results with:transducers
[53]
[PDF] A CMOS Readout Circuit for Resistive Transducers Based on ...
The digitally-constructed bandgap reference and temperature sensor achieve performance close to that of other state-of-the-art voltage references and ...
[54]
[PDF] LM61440-Q1 Automotive 3-V to 36-V, 4-A, Low EMI Synchronous ...
The LM61440-Q1 devices are AEC-Q100-qualified and have electrical characteristics ensured up to a maximum junction temperature of 150°C. www.ti.com · LM61440-Q1.
[55]
[PDF] OPTIREG™ linear TLS835B2ELV datasheet - Infineon Technologies
Dec 9, 2024 · Qualified for automotive applications. Product validation according to AEC-Q100. Description. The OPTIREG™ linear TLS835B2ELV is a linear ...
[56]
An ultralow-power CMOS bandgap voltage reference with N+ doped ...
The chip can operate with a supply voltage from 1.2 V to 1.8 V and small area of the bandgap is around 0.001 mm2. The characteristic of the proposed voltage ...Missing: mm² | Show results with:mm²
[57]
[PDF] A Low-Power CMOS Bandgap Voltage Reference for Supply ...
Aug 8, 2021 · The value of the reference voltage produced by a standard bandgap (BG) circuit, around 1.2 V, makes it not suitable for ultralow-voltage ...Missing: V_sat | Show results with:V_sat<|separator|>
[58]
Chapter 13: The Zener Diode and the TC Zener Reference
The zener diode was the first discrete semiconductor device to be used as a basic voltage reference. It was created in the late 1950s by its inventor ...Missing: instability | Show results with:instability
[59]
The ultimate zener-diode reference - EDN
Sep 30, 2004 · Using a 6.3V zener diode is common because it is the most stable zener diode over time and temperature (Reference 3). The buried-zener diode ...
[60]
Transistor Technology - Bell Telephone Laboratories - Google Books
Bibliographic information ; Publisher, Van Nostrand, 1958 ; Original from, the University of Michigan ; Digitized, Dec 18, 2006 ; Length, 1778 pages.
[61]
[PDF] TRANSISTOR MANUAL - World Radio History
In 1833, Michael Faraday, the famed English scientist, made what is perhaps the first significant contribution to semiconductor research.
[62]
US3617859A - Electrical regulator apparatus including a zero ...
An integrated circuit regulator including a temperature stable constant voltage reference wherein the negative temperature coefficient of the base-to-emitter ...Missing: 3271660 4249122 4447784
[63]
US4249122A - Temperature compensated bandgap IC voltage ...
The invention relates to an improvement in temperature compensated voltage reference circuits. U.S. Pat. No. 3,617,859 issued to Robert C. Dobkin and Robert J.Missing: 3271660 4447784
[64]
Temperature compensated bandgap voltage reference circuit
In the prior art one well known reference circuit is disclosed in U.S. Pat. No. 3,617,859 to Robert C. Dobkin and Robert J. Widlar. Here a two-terminal circuit ...Missing: Hilbiber | Show results with:Hilbiber
[65]
https://ieeexplore.ieee.org/document/933463
[66]
A 54 µW CMOS Auto-Trimming Bandgap References (ATBGR ...
Sep 1, 2023 · An auto-trimming CMOS bandgap references circuit (ATBGR) with PSRR enhancement circuit for artificial intelligence of things (AIoT) chips is presented in this ...Missing: adaptive | Show results with:adaptive
[67]
https://www.analog.com/media/en/technical-documentation/data-sheets/ADR4520_4525_4530_4533_4540_4550.pdf
[68]
https://www.ti.com/lit/ds/sbos410o/sbos410o.pdf
[69]
[PDF] A High Temperature 4H-SiC Voltage Reference for Depletion Mode ...
The proposed voltage reference adopts Widlar bandgap reference topology, and it aims to provide a negative reference voltage for Gallium Nitride (GaN) circuits ...