Fact-checked by Grok 2 weeks ago

Lithium disilicate

Lithium disilicate is a glass-ceramic material primarily composed of lithium oxide (Li₂O) and silicon dioxide (SiO₂), with the chemical formula Li₂Si₂O₅, featuring interlocking needle-like crystals embedded in a residual glass matrix.^[1] This microstructure provides exceptional mechanical properties, including a flexural strength of 360–400 MPa and fracture toughness of 2.0–3.5 MPa·m¹/², making it suitable for high-load dental restorations.^[1] Its high translucency and color-matching capabilities closely mimic natural tooth enamel, enhancing aesthetic outcomes in clinical applications.^[1] Introduced in dentistry in the late 1990s as a pressed ceramic (e.g., IPS Empress 2), it has evolved into CAD/CAM-compatible forms like IPS e.max, enabling precise fabrication through processes such as hot pressing or milling followed by crystallization at approximately 840–850°C.^[2] The material's biocompatibility and wear resistance further support its use in monolithic crowns, veneers, inlays, onlays, and fixed partial dentures, with clinical survival rates exceeding 95% over 3–10 years.^[2] Advantages include minimal plaque accumulation and reduced risk of chipping compared to earlier ceramics, though successful bonding requires surface etching with hydrofluoric acid and silane application.^[2] While predominantly employed in restorative dentistry, lithium disilicate's durability has led to emerging applications in bioremediation materials and display technologies due to its optical and structural integrity.^[3] Limitations involve potential fabrication challenges, such as viscosity control during processing, which can affect homogeneity.^[1]

Introduction

Definition and composition

Lithium disilicate is a glass-ceramic material primarily composed of lithium silicate crystals embedded in a glassy matrix, classified as a lithium silicate-based glass-ceramic widely used in dental applications due to its biocompatibility and machinability.^[4] The primary crystalline phase is lithium disilicate, with the chemical formula \ce{Li2Si2O5}.^[5] Its molar mass is 150.05 g/mol.^[6] Typical compositions of lithium disilicate glass-ceramics consist of 57–80 wt% \ce{SiO2} as the main network former, 11–19 wt% \ce{Li2O} to facilitate crystallization, 0–13 wt% \ce{K2O} as a flux, and 1–7 wt% \ce{P2O5} as a nucleating agent.^[7] Minor additives, such as 0–7 wt% \ce{Al2O3} for enhancing mechanical properties, \ce{ZrO2} for nucleation and strengthening, and \ce{CeO2} for nucleation and coloring, are included to tailor the material's performance.^[8]

Historical development

Research on lithium silicates for glass-ceramics began in the 1950s, when Donald Stookey at Corning Glass Works discovered the process of controlled nucleation and crystallization, leading to the identification of lithium disilicate (Li₂Si₂O₅) as a key phase capable of imparting high strength to glass-ceramic materials.^[9]^[10] During the 1950s and 1970s, extensive studies focused on the lithium silicate system, particularly the stoichiometric Li₂O-2SiO₂ composition, to develop materials with enhanced mechanical properties for industrial applications.^[11] In the 1970s, researchers George Beall and Lina M. Echeverria advanced this work by exploring lithium disilicate glass-ceramics with improved microstructures, laying the groundwork for specialized uses.^[12]^[13] The adaptation of lithium disilicate for dental applications gained momentum in the 1990s, driven by Ivoclar Vivadent's efforts to create high-strength, aesthetically superior alternatives to existing ceramics. This culminated in the launch of IPS Empress 2 in 1998, the first commercial lithium disilicate glass-ceramic for indirect dental restorations.^[14]^[15] Ivoclar Vivadent further refined the material, introducing the IPS e.max system in 2005, which expanded options for pressable and machinable forms.^[16]^[17] A key milestone in the 2000s was the development of CAD/CAM-compatible blocks, such as IPS e.max CAD launched in 2006, enabling efficient chairside fabrication of restorations.^[18]^[19] This evolution was propelled by the demand for all-ceramic restorations over traditional metal-ceramics, primarily to achieve better aesthetics and biocompatibility while maintaining durability.^[20]^[21] Clinical studies have validated its performance, reporting 5-year survival rates of 97.8% for single crowns and 78.1% for partial fixed dental prostheses, and 10-year rates of 96.7% for crowns and 70.9% for partial fixed dental prostheses.^[22] These outcomes underscore lithium disilicate's role in shifting dental practice toward metal-free solutions that prioritize natural appearance.^[4]

Structure and microstructure

Crystal structure

Lithium disilicate adopts an orthorhombic crystal system with space group Ccc2.^[23] The unit cell has approximate parameters a = 5.79 Å, b = 14.61 Å, c = 4.77 Å.^[23] In this structure, the atomic arrangement features [SiO₄] tetrahedra sharing corners to form chains, with Li⁺ ions coordinated tetrahedrally by oxygen atoms, resulting in a layered configuration of silicate sheets separated by lithium layers.^[23] Lithium disilicate exhibits polymorphism, with a high-temperature β-Li₂Si₂O₅ phase (orthorhombic) and a low-temperature α-Li₂Si₂O₅ phase (monoclinic); the β form is the thermodynamically stable phase observed in glass-ceramics used for practical applications.^[24]

Glass-ceramic formation

The formation of lithium disilicate glass-ceramics involves a controlled crystallization process that transforms the amorphous base glass into a composite material with embedded crystals, primarily through a two-stage heat treatment. In the initial nucleation stage, the glass is heated to temperatures between 450°C and 550°C, where metastable lithium metasilicate (Li₂SiO₃) seeds form as precursors to the target phase.^[25] This stage typically lasts 1–8 hours to generate a high density of nucleation sites, ensuring uniform crystal distribution throughout the material.^[26] Nucleating agents play a critical role in this stage by promoting heterogeneous nucleation and controlling crystal size and distribution. Common additives such as phosphorus pentoxide (P₂O₅) or zirconia (ZrO₂) are incorporated into the glass composition at concentrations of 1-12 wt%, forming secondary phases like lithium phosphate (Li₃PO₄) or zirconate compounds that serve as sites for Li₂SiO₃ precipitation.^[27] P₂O₅, in particular, is widely used in dental formulations, contributing 5-15 vol% of the final microstructure as Li₃PO₄ while enhancing the nucleation rate by up to two orders of magnitude.^[14] These agents lower the energy barrier for crystal formation, preventing uncontrolled devitrification and allowing precise tailoring of the microstructure.^[28] Following nucleation, the second stage involves heating to 800-850°C (for dental-grade materials), where the Li₂SiO₃ seeds dissolve and recrystallize into the stable lithium disilicate (Li₂Si₂O₅) phase through a solid-state reaction.^[25] This growth phase, often held for 1-2 hours, results in the development of a fine-grained microstructure characterized by randomly oriented, interlocking needle-like or plate-like crystals with lengths of 0.5-2 μm.^[29] The elongated morphology arises from anisotropic crystal growth kinetics, where the crystals interlock to form a reinforced network within the residual glass matrix, contributing to the material's overall integrity.^[30] In dental-grade lithium disilicate glass-ceramics, the crystalline phase typically achieves a volume fraction of approximately 70 vol%, with the lithium disilicate crystals dominating the structure alongside minor nucleating agent-derived phases.^[14] This high crystallinity is optimized during the heat treatment to balance phase purity and microstructural homogeneity, ensuring reproducible performance in applications.^[30]

Properties

Mechanical properties

Lithium disilicate glass-ceramics exhibit a biaxial flexural strength typically ranging from 360 to 530 MPa (depending on specific product and processing, per ISO 6872), enabling their use in load-bearing dental applications.^[31] This strength arises from the high volume fraction of interlocking lithium disilicate crystals within the glassy matrix, which distributes stress effectively under flexural loads.^[1] The fracture toughness (K_IC) of lithium disilicate is reported as 3.3 ± 0.14 MPa·m^{1/2}, attributed to mechanisms such as crack deflection and bridging facilitated by the needle-like, interlocking crystal morphology.^[32] These microstructural features promote energy dissipation during crack propagation, enhancing resistance to brittle failure compared to traditional glass-ceramics. Young's modulus for lithium disilicate falls in the range of 90-100 GPa, reflecting its stiff yet somewhat flexible nature relative to dentin, which aids in mimicking natural tooth biomechanics.^[33] Vickers hardness is approximately 5.3–6.0 GPa, contributing to wear resistance.^[32] The Weibull modulus, ranging from 10 to 15, indicates a relatively reliable strength distribution with low variability in failure probability, underscoring consistent performance across specimens.^[34] Under cyclic loading, lithium disilicate demonstrates good fatigue resistance, maintaining structural integrity over extended periods and supporting its suitability for posterior restorations subjected to masticatory forces.^[35] This durability is linked to the material's ability to resist subcritical crack growth, as evidenced in simulated chewing simulations.

Physical, optical, and chemical properties

Lithium disilicate glass-ceramics have a density ranging from 2.5 to 2.6 g/cm³, which supports their lightweight yet robust nature in dental applications. This density arises from the fine-grained crystalline structure embedded within a glassy matrix, contributing to overall material efficiency without compromising volume stability.^[36]^[37] The coefficient of thermal expansion for lithium disilicate is typically 10 to 12 × 10⁻⁶ K⁻¹, making it highly compatible with the thermal expansion coefficients of dental alloys (around 10–14 × 10⁻⁶ K⁻¹) and natural tooth structures (approximately 11 × 10⁻⁶ K⁻¹). This compatibility minimizes internal stresses during thermal cycling in the oral environment, such as from hot or cold foods. The interlocking microstructure formed during glass-ceramic processing further enhances thermal shock resistance.^[38] Optically, lithium disilicate offers excellent translucency, with transmittance values of 25–35% at 550 nm for clinically relevant thicknesses (e.g., 1–2 mm), allowing natural light diffusion similar to dentin and enamel. Its refractive index of approximately 1.55 closely matches that of human enamel (1.62), reducing light scattering at interfaces and enhancing lifelike aesthetics. To achieve precise shade matching with the Vita classical shade guide, metal oxides such as iron, titanium, and cerium are incorporated as colorants during synthesis, enabling a range of A1–D4 shades with minimal opacity variation.^[39]^[40] Chemically, lithium disilicate demonstrates high stability, with solubility in oral fluids below 10 μg/cm², well under ISO 6872 standards for dental ceramics (<100 μg/cm²).^[41] It resists degradation in acidic environments (pH 2–10), including exposure to citric acid from beverages or gastric reflux, due to the stable Si–O–Li network that limits ion leaching.^[25] This durability ensures long-term integrity in the oral cavity without significant surface erosion or color alteration. In terms of bioactivity, lithium disilicate promotes osseointegration through surface apatite formation when immersed in simulated body fluid (SBF), where calcium and phosphate ions from the solution deposit as hydroxyapatite layers within 7–14 days. This process, driven by the release of silicon and lithium ions that nucleate apatite crystallization, supports bone apposition around implants or restorations.^[42]

Production methods

Synthesis of base glass

The synthesis of the base glass for lithium disilicate begins with the selection of high-purity raw materials, primarily quartz (SiO₂) as the silica source, lithium carbonate (Li₂CO₃) to provide Li₂O, potassium carbonate (K₂CO₃) for K₂O, phosphorus pentoxide (P₂O₅) as a nucleating agent, and additives such as alumina (Al₂O₃) to modify viscosity and stability.^[43]^[44] These reagents, typically of analytical grade with purity exceeding 99%, are weighed according to the target molar composition—commonly around 65-70 mol% SiO₂, 25-30 mol% Li₂O, 2-3 mol% K₂O, 2-3 mol% P₂O₅, and 0.5-3 mol% Al₂O₃—and ball-milled or mechanically mixed for several hours to ensure uniformity.^[45] The homogeneous batch is loaded into crucibles, often platinum or high-alumina types to withstand high temperatures and avoid contamination, and melted in an electric furnace at 1350-1500°C for 1-4 hours.^[46]^[44] This duration allows for complete dissolution and fining of the melt, resulting in a clear, bubble-free viscous liquid with the desired amorphous structure.^[45] Stirring may be employed periodically to enhance homogeneity, particularly in larger batches.^[47] Upon completion of melting, the molten glass is rapidly quenched to preserve its amorphous state and prevent unintended crystallization. Common methods include pouring the melt into distilled water to form frit or into a preheated metal mold (e.g., at 450-500°C), followed by controlled annealing at 450-500°C for 1-2 hours to relieve internal stresses, and slow cooling to room temperature.^[44]^[45] This quenching step yields solid ingots or frit that can be further ground into powder for downstream applications, maintaining the glass's transparency and homogeneity.^[48] Composition tuning is essential to tailor the base glass for specific uses, such as increasing P₂O₅ content (typically 2-3.5 mol%) in dental-grade formulations to promote effective nucleation sites during later processing. Compositions are often slightly non-stoichiometric (deviating from the ideal Li₂Si₂O₅ ratio) to enhance nucleation and final properties.^[49] While industrial variants may incorporate alternative modifiers like ZrO₂ or B₂O₃ for enhanced thermal stability or cost efficiency, these adjustments ensure the glass precursor aligns with performance requirements without altering the core Li₂O-SiO₂ matrix.^[50]^[44]

Processing techniques

Lithium disilicate glass-ceramics are primarily fabricated into finished products through techniques that transform pre-formed ingots or blocks into precise shapes, often tailored for high-strength applications such as dental frameworks. These methods leverage controlled heat treatments to achieve the desired crystallization while maintaining structural integrity.^[51] One established processing technique is lost-wax investment casting, also known as hot pressing, where lithium disilicate ingots—derived from base glass—are melted and injected into molds. The ingots are heated to the pressing temperature of approximately 900–950°C to achieve a viscous state suitable for pressing, allowing the material to fill intricate mold cavities created via the lost-wax method for complex frameworks.^[52] This process typically involves investment burnout followed by pressing to finalize the shape, resulting in restorations with uniform density and minimal porosity.^[53] A widely adopted modern approach is CAD/CAM milling, which enables digital design and subtractive fabrication from partially crystallized blocks. These blocks undergo initial nucleation at around 500°C to form lithium metasilicate seeds, making them machinable in a "soft" state; milling then produces the desired geometry, followed by a crystallization firing at 840°C for 10–20 minutes to convert the structure to lithium disilicate (Li₂Si₂O₅) and densify the material.^[54] This method offers high precision and repeatability, with firing cycles optimized to achieve flexural strengths exceeding 400 MPa.^[38] Emerging techniques include additive manufacturing, such as stereolithography-based 3D printing of lithium disilicate glass slurries or lithography-based ceramic manufacturing (LCM). In these processes, a photosensitive slurry is layer-by-layer printed to form green bodies, which are then debound and post-sintered at temperatures up to 900–1000°C to fully crystallize the Li₂Si₂O₅ phase, enabling complex geometries with resolutions down to 25 μm.^[55] These methods show promise for customized production, though they require optimization to match the mechanical properties of traditional techniques.^[56] Post-processing finishing is essential for achieving optimal aesthetics and performance. Surfaces are polished using diamond burs and pastes to attain roughness values of 0.1–1 μm Ra, reducing bacterial adhesion and enhancing durability without compromising strength.^[57] Aesthetic customization involves staining and a final low-temperature firing (around 750–800°C) to fuse colors and glazes.^[58] Quality control in lithium disilicate processing relies on techniques like X-ray diffraction (XRD) to confirm the crystalline phase composition, ensuring the Li₂Si₂O₅ content exceeds 70% for reliable mechanical properties.^[59] This verification step detects deviations in crystallization, such as residual glass phases, which could affect clinical performance.^[60]

Applications

Dental restorations

Lithium disilicate is widely indicated for various dental restorations, including single crowns, veneers with thicknesses ranging from 0.3 to 1 mm, inlays and onlays, bridges up to three units (with the second premolar as the terminal abutment), and implant-supported crowns.^[31]^[61] These applications leverage its suitability for both tooth- and implant-supported prosthetics, particularly in anterior and posterior regions where aesthetic demands are high.^[61] Key advantages in dentistry include its superior aesthetic matching to natural teeth due to high translucency and shade versatility, allowance for minimally invasive tooth preparation, and excellent bondability with resin cements facilitated by its silica content.^[61] Its flexural strength supports reliable performance in load-bearing areas without requiring extensive tooth reduction.^[31] The fabrication workflow typically begins with intraoral digital scanning to capture the preparation, followed by computer-aided design (CAD) of the restoration, milling from pre-crystallized blocks using CAD/CAM systems, crystallization firing at 840-850°C for about 10 minutes to achieve the final microstructure, and adhesive cementation after surface treatment with 5% hydrofluoric acid etching for 20 seconds and silane application.^[61]^[31] Clinical outcomes demonstrate high reliability, with survival rates of 94-98% at five years for crowns and veneers, and low fracture incidence of 1-2% in monolithic forms over extended follow-up periods up to eight years.^[61]^[62] These rates reflect robust performance in both anterior and posterior applications, with minimal complications such as chipping or debonding when properly bonded.^[62] Lithium disilicate exhibits excellent biocompatibility, showing no cytotoxicity toward fibroblasts and promoting favorable soft tissue responses with low plaque retention compared to titanium.^[63]^[61] It supports epithelial cell and fibroblast proliferation without inflammation and contributes to periodontal health by facilitating healthy gingival adaptation around restorations.^[63]^[64]

Industrial and other uses

Lithium disilicate glass-ceramics serve as non-conductive seals and enamels in metallurgy, particularly for bonding with nickel-based superalloys and stainless steels in high-temperature environments up to 1050°C, forming hermetic seals through interfacial redox reactions that match thermal expansion coefficients.^[65] These applications leverage the material's high electrical resistivity and ability to create strong bonds (up to 14,000 psi) without deleterious reactions at the interface.^[65]^[66] In electronics, lithium disilicate acts as an insulator for sealing to metal substrates, supporting thermal management in components like hard disk drives due to its thermal expansion of approximately 105 × 10⁻⁷ K⁻¹ and chemical stability in harsh environments.^[49] It is also employed in bioremediation filters, where its biocompatibility and resistance to degradation enable effective pollutant capture without leaching harmful substances.^[3] Emerging applications include smart terminal display windows, utilizing the material's optical transparency and mechanical strength for durable, high-clarity interfaces in consumer electronics.^[3] Beyond dentistry, bioactive variants with rod-shaped crystals (aspect ratio 4:1) are explored for coatings on medical implants, promoting bone tissue engineering through enhanced regeneration properties.^[49] Key advantages encompass high thermal shock resistance from its tough microstructure, enabling survival in fluctuating temperatures, and excellent compatibility with metal substrates for reliable adhesion in seals.^[49] However, industrial adoption remains less widespread than dental uses due to elevated production costs and the need for specialized precision manufacturing.

References

[1]
Lithium Disilicate - an overview | ScienceDirect Topics
Because lithium disilicate glass-ceramics are similar in appearance to natural teeth and their flexural strength is in the range of 360–400 MPa, they can be ...
[2]
Overview of Lithium Disilicate as a restorative material in dentistry
### Summary of Lithium Disilicate from the Article
[3]
Research Progress and Applications of High-performance Lithium ...
Dec 1, 2024 · Lithium disilicate glass-ceramics (LDGCs) are widely used in fields, such as bioremediation materials and smart terminal display windows.
[4]
Dental ceramics: An update - PMC - NIH
The crystalline phase that forms is a lithium disilicate (Li2Si2O5) and makes up about 70% of the volume of the glass ceramic. Lithium disilicate has an unusual ...<|control11|><|separator|>
[5]
Lithium disilicate | Li2O5Si2 | CID 101943115 - PubChem
Lithium disilicate ; Molecular Weight. 150.1 g/mol. Computed by PubChem 2.2 (PubChem release 2025.04.14) ; Component Compounds. CID 3028194 (Lithium) · CID 61566 ...
[6]
Li2Si2O5 (Lithium disilicate) molar mass
Calculate molar mass of each element: multiply the atomic mass of each element by the number of atoms of that element in the compound. Add them together: ...
[7]
Assessment of Radiation absorption parameters of lithium disilicate ...
Jan 23, 2025 · LD glass ceramics typically contain silica (57–80 weight%), lithium oxide (11–19 weight%), potassium oxide (0–13 weight%), phosphorous ...
[8]
[PDF] Lithium silicate-based glass ceramics in dentistry: a narrative review.
May 2, 2024 · ant, and supplemental oxides (e.g., Al2O3, K2O, ZrO2, ZnO, MgO and CeO2) are added as secondary nucleating agents, fluxes or fining agents ...
[9]
Dr. S. Donald (Don) Stookey (1915–2014): Pioneering Researcher ...
Aug 23, 2016 · He discovered that actual glass-forming silicate compounds such as barium disilicate and lithium metasilicate could be nucleated, albeit in ...<|separator|>
[10]
Lithium Silicate-Based Glass Ceramics in Dentistry: A Narrative ...
May 2, 2024 · Contemporary dental ceramic materials, a review: Chemical composition, physical and mechanical properties, indications for use. Open Access ...2. Microstructure · 7.1. Intaglio Surface... · 7.1. 2. Chemical Surface...
[11]
[PDF] Controlling Internal Crystallization of Li2Si2O5 Glass-Ceramics ...
May 8, 2025 · The lithium silicate system has been studied intensively since its discovery by D. Stookey. The stoichiometric Li2O-2SiO2 glass system (33.33 ...
[12]
Microstructural development during heat treatment of a commercially ...
Mar 1, 2019 · Lithium disilicate glass-ceramic was first introduced to dentistry by Beall & Echeverria [1], and commercialized by Ivoclar Vivadent in 1998 ...
[13]
Crystallization Process and Some Properties of Li2O–SiO2 Glass ...
Nov 24, 2008 · Echeverria, “New Lithium Disilicate Glass–Ceramics,” Bol. Soc. Esp. Ceram. Vid., 5, 183–8 (1992). Google Scholar. 12 G. H. Beall, “Glass ...<|separator|>
[14]
A Critical Review of Dental Lithia-Based Glass–Ceramics - PMC - NIH
IPS Empress 2, launched in 1998 by Ivoclar Vivadent, was the first commercial lithia-based silicate glass–ceramic (Schweiger et al. 1999). It was succeeded by ...
[15]
Overview of Lithium Disilicate as a restorative material in dentistry
Lithium disilicate was first introduced to the dental field as an indirect restorative material in 1998. It was marketed under the name IPS Empress 2, ...
[16]
IPS e.max celebrates its 20th anniversary and continues to lead the ...
Mar 24, 2025 · The IPS e. max family was introduced in 2005 with a range of different products, including the two high-strength lithium disilicate glass- ...
[17]
History | About Us | Ivoclar USA
The IPS e.max lithium disilicate glass-ceramic was introduced in 2005. Within a very short time, this material established itself as the benchmark for all ...
[18]
and Fully Crystallized Chairside CAD/CAM Lithium Disilicate Ceramics
Lithium disilicate was introduced for CAD-CAM systems in the mid-2000s as pre-crystallized ceramic blocks, being marketed as IPS e.max CAD by Ivoclar ...
[19]
Chairside CAD/CAM Materials: Current Trends of Clinical Uses - PMC
Nov 12, 2021 · IPS e.max CAD (Ivoclar Vivadent) was introduced in 2006 as a lithium disilicate with a bending resistance over 350 MPa and significantly greater ...
[20]
All-ceramic materials in dentistry
Recent trends show a shift from metal-ceramics to metal-free restorations in the dental field. ... Lithium disilicate glass ceramics. The second generation ...Heat-Pressed Ceramics · Lithium Disilicate Glass... · Zirconia Ceramics
[21]
[PDF] An Overview of the Current Survival Status and Clinical ...
2,3 The main reason to use all ceramics instead of metal-ceramics is based on the former's more favorable esthetics.4 Various ceramic materials have been ...<|control11|><|separator|>
[22]
Clinical outcomes of lithium disilicate single crowns and partial fixed ...
... 5-year cumulative survival rate was 78.1%. The cumulative survival rate over a 10-year period, primarily owing to data from 1 study, was 96.7% for single ...
[23]
Structural properties and mechanical stability of monoclinic lithium ...
Jun 9, 2017 · Monoclinic Li2Si2O5 has lattice parameters of a = 5.82 Å, b = 14.66 Å and c = 4.79 Å, resulting in a unit cell volume of 408.69 Å3, as ...
[24]
Crystal Growth and Nucleation in Glasses in the Lithium Silicate ...
Investigating crystal growth and nucleation in lithium silicate glasses. Study on phase separation and homogenization of glasses. Determining nucleation and ...
[25]
Characterisation and Properties of Lithium Disilicate Glass Ceramics ...
Aug 7, 2013 · This work proposes four different glass formulas derived from the SiO2-Li2O-K2O-Al2O3 system to investigate the effect of glass composition ...
[26]
The mechanism of deceleration of nucleation and crystal growth by ...
May 6, 2016 · The addition of small amounts of niobium or tantalum oxide to lithium disilicate glass provokes a drastic decrease of the steady-state ...
[27]
Disclosing crystal nucleation mechanism in lithium disilicate glass ...
Oct 20, 2020 · Structure of the LS and LS2 crystals along different orientations and unit cell parameters. ... crystal structure with a unit cell (P1 symmetry) ...
[28]
Crystallization toughening of a model glass-ceramic - ScienceDirect
These commercial glass-ceramics typically contain a 50–80% volume fraction of 1–10 μm lithium disilicate crystals embedded in a residual glass matrix. The ...
[29]
https://www.sciencedirect.com/science/article/abs/pii/S0272884220337391
[30]
Fracture toughness and hardness evaluation of three pressable all ...
This study evaluates the fracture toughness and hardness of three pressable all-ceramic materials: IPS-Empress, Empress 2 and an experimental ceramic material.
[31]
The influence of core-build up materials on biaxial flexural strength ...
Dec 3, 2024 · The aim of this study was to investigate the effect of using different core build-up materials on biaxial flexural strength (BFS) of multilayered strength- ...
[32]
Durability and Weibull Characteristics of Lithium Disilicate Crowns ...
Oct 15, 2014 · The aim of this study was to evaluate the durability of lithium disilicate crowns bonded on abutments prepared with two types of finish ...
[33]
Lithium Disilicate Restorations Fatigue Testing Parameters - PubMed
Purpose: To review laboratory studies that investigated fatigue resistance of lithium disilicate ... Keywords: Cyclic loading; chewing simulator; laboratory ...
[34]
Comparative Invitro Testing of the Tensile Bond Strength Under ...
Aug 5, 2024 · Density (g/cm2), 2.5, 2.4 ; Crystal system, Lithium disilicate crystals measure 3-6 µm in length, Lithium disilicate crystals measure 1.5 × 0.5 ...
[35]
Lithium Disilicate - Yucera
2.3-2.6g/cm3. Density. YUCERA Lithium Disilicate. The perfect combination of aesthetics and performance. 400 MPa. Strength. 550 HV Hardness. 2.3-2.6 g/cm3
[36]
Translucency and Strength of Lithium Disilicate for Computer-Aided ...
... thermal expansion (CTEs) between the LD phase and the glass matrix, which are 10.1–10.8 × 10−6/K and 12.2–12.8 × 10−6/K, respectively [26,27,28]. Higher ...
[37]
Modulation of Lithium Disilicate Translucency through Heat Treatment
Apr 21, 2021 · The aim of this study was to present a control method for modulating the translucency of lithium disilicate ceramics through thermal refinement.
[38]
https://pmc.ncbi.nlm.nih.gov/articles/PMC10820003/
[39]
Phase Formation, Mechanical Strength, and Bioactive Properties of ...
Nov 22, 2022 · Lithium disilicate glass–ceramics can be improved by adding K2O and Al2O3, increasing their mechanical properties by up to 201 MPa [14,15]. The ...
[40]
[PDF] Preparation of Lithium Disilicate Glass- Ceramics as Dental Bridge ...
powders were used as raw materials. The glass composi- tions were melted in high-alumina crucibles in an electric furnace, at 1350 °C for 1 h. The obtained ...
[41]
https://ivodent.hu/__docs/772_379d2f11a072ee3ad1c4da7e8d7df04a.pdf
[42]
Lithium disilicate-containing glass-ceramics some of which are self ...
Echeverria under the title COLORED, TEXTURED GLASS-CERAMIC ARTICLES describes the production of glass-ceramic articles exhibiting a variegated color, surface ...
[43]
Complex shapes of lithium disilicate glass-ceramics developed by ...
Jan 25, 2024 · The mixture was melted on a platinum crucible at 1500 °C for 2 h, poured on a brass plate, and immediately annealed at 450 °C, followed by slow ...Missing: synthesis | Show results with:synthesis
[44]
Porous Lithium Disilicate Glass–Ceramics Prepared by Cold ... - MDPI
Jan 12, 2024 · The obtained mixtures were melted in silica crucible at 1600 °C for 4 h in air, then immediately quenched in deionized water to prepare glass ...
[45]
Effects of P 2 O 5 and heat treatment on crystallization and ...
In this study, a new lithium disilicate glass ceramic system was prepared by the conventional fusion method as a dental material (Li2O–SiO2–K2O–ZnO–CaO–P2O5).Missing: industrial | Show results with:industrial
[46]
The Science Behind Lithium Disilicate: A Metal-Free Alternative
Mar 1, 2009 · Lithium disilicate is a highly aesthetic, high-strength material that can be conventionally cemented or adhesively bonded.
[47]
[PDF] Lithium Disilicate: The Future Of All-Ceramic Dentistry
IPS e.max lithium disilicate has a needle-like crystal structure that offers excellent strength and durability as well as outstanding optical properties ...
[48]
Effect of Heat-Pressing Temperature and Holding Time on the ...
May 18, 2015 · ... lithium disilicate glass ceramic. An experimental lithium . ... Chemical solubility and flexural strength of zirconia-based ceramics. Int ...
[49]
The science and application of IPS e.Max dental ceramic
The new ceramic formulation was released in 2005 under the brand of IPS™ e.Max Press [5]. Ultimately the introduction of the e.Max line would lead to the ...
[50]
Stereolithography-based additive manufacturing of lithium disilicate ...
Lithium disilicate glass ceramic can be reproducibly printed, debinded and sintered. · Stereolithography provides highest resolution of 25 μm and accuracy of 50 ...
[51]
Manufacturing and characterization of a 3D printed lithium disilicate ...
The objective of this study was to manufacture and to evaluate the physico-mechanical properties of the Lithium disilicate (Li 2 O 5 Si 2 ) ceramic structures
[52]
Surface Roughness of Milled Lithium Disilicate With and ... - PubMed
Surface roughness depends on the specific finishing system and ceramic combination used. There was a significant difference in finishing treatments.
[53]
Versus Post-Crystallization Polish of Two High-Strength Silicate ...
Mar 26, 2024 · For lithium disilicate (LDS), the timing of the post-milling procedures did not significantly affect surface roughness values (p = 0.129). In ...
[54]
Improved performances of lithium disilicate glass-ceramics by seed ...
Jan 22, 2021 · lithium-disilicate glass ceramics for monolithic restorations. ... Effect of alumina on the strength, fracture toughness, and crystal structure of ...<|control11|><|separator|>
[55]
Microstructure and Mechanical Properties of Li2Si2O5 Whisker ...
Feb 20, 2022 · Lithium disilicate (Li2Si2O5) glass-ceramics are an ideal material for dental restoration; however, their intrinsic brittleness and low defect ...
[56]
IPS e.max CAD | Lithium disilicate block for CAD/CAM | Ivoclar USA
3-unit bridges up to the second premolar as the terminal abutment; Implant-supported hybrid single-tooth restorations (hybrid abutments, hybdrid abutment ...
[57]
Current status on lithium disilicate and zirconia: a narrative review
Jul 4, 2019 · Clinical survival of chair-side generated monolithic lithium disilicate crowns:10-year results. ... 2019;12:6. https://doi.org/10.3390 ...
[58]
Fracture rate of 188695 lithium disilicate and zirconia ceramic ...
Lithium disilicate monolithic single crowns had a fracture rate of 0.96%, which was significantly lower than that of layered single crowns at 1.26% (P<. 05).
[59]
Biocompatibility of Lithium Disilicate and Zirconium Oxide Ceramics ...
Jul 19, 2021 · The results indicate that the two tested high-strength ceramics and surface properties are biologically suitable for transmucosal implant components.
[60]
[PDF] Comparison of periodontal response between subgingivally placed ...
Feb 8, 2023 · ABSTRACT. The goal of the present study was to critically compare the impact of lithium disilicate and zirconium dioxide.
[61]
Interfacial bonding oxides for glass-ceramic-to-metal seals
Lithium silicate-based glass-ceramics with high coefficients of thermal expansion, designed to form matched hermetic seals in 304L stainless steel housing, show ...
[62]
[PDF] Sealing Glasses
Apr 16, 2015 · Deleterious reactions can occur at the glass-stainless steel interface- Example: 304 stainless steel/lithium silicate GC. Cr x-ray map.Missing: enamels | Show results with:enamels
[63]
Fundamentals and advances in production and application of non ...
This paper aims at briefly describe the main achievements regarding the fundamental research, production and applications of lithium disilicate based glass- ...
[64]
Dental Lithium Disilicate Market - Market Share, Industry Analysis ...
Jun 19, 2023 · Limitations associated with dental lithium disilicate are expected to hamper the market's growth. Emax crowns are high in price. For ...
[65]
Dental Lithium Disilicate Market Size & Share Trends, 2033
Additionally, advanced milling machines and furnaces tailored for lithium disilicate firing cycles can cost upwards of USD 50,000, limiting their adoption to ...