Fact-checked by Grok 2 weeks ago

SAE J1772

SAE J1772 is a North American standard developed by SAE International that defines the conductive charging coupler for alternating current (AC) charging of electric vehicles (EVs) and plug-in hybrid electric vehicles (PHEVs).^[1] It specifies the physical design, electrical characteristics, communication protocols, and performance requirements for the charging system to ensure safety, interoperability, and efficiency between vehicles and electric vehicle supply equipment (EVSE).^[1] The standard primarily supports Level 1 charging at 120 V AC with up to 12 A (approximately 1.4 kW) and Level 2 charging at 208–240 V AC with currents ranging from 16 A to 80 A (up to 19.2 kW), using a five-pin Type 1 connector that includes two power pins (L1 and L2/Neutral), a ground pin, a control pilot for vehicle-EVSE communication, and a proximity pilot for detecting connector insertion.^[2]^[3] The connector features a round housing approximately 43 mm in diameter, designed for single-phase electrical systems common in North America.^[4] Development of SAE J1772 originated in 1996 as an SAE Recommended Practice to establish requirements for EV conductive charging systems, driven by collaborations including General Motors and Southern California Edison.^[5] The standard gained traction in 2001 when it was adopted by the California Air Resources Board (CARB) as the required interface for zero-emission vehicle charging in California, promoting widespread industry acceptance.^[6] A major revision occurred in 2009, leading to formal adoption by the SAE Motor Vehicle Council on January 14, 2010, which incorporated input from automakers like GM, Ford, Chrysler, Toyota, and Nissan.^[7] Subsequent updates in 2012, 2017, and the latest in January 2024 have refined dimensions, corrected errors, updated references, and enhanced compatibility while maintaining backward compatibility.^[1] SAE J1772 remains a primary standard for AC charging in North America, used by nearly all non-Tesla EVs produced before 2025 and much of the public charging infrastructure, enabling seamless interoperability across manufacturers.^[3] However, as of 2025, it is being supplemented by the SAE J3400 standard (based on Tesla's NACS), adopted by several manufacturers for new electric vehicles.^[8] It forms the foundation for the Combined Charging System (CCS1), an extension that adds two DC pins below the J1772 connector for fast charging up to 350 kW, further solidifying its role in the EV ecosystem.^[2] The standard's emphasis on safety features, such as pilot signal verification to prevent faults and automatic current limiting, has supported the growth of EV adoption by ensuring reliable and secure charging.^[9]

History and Development

Origins and Initial Standardization

The development of SAE J1772 originated in 1996 as an SAE Recommended Practice to establish requirements for EV conductive charging systems. A major revision effort began with the formation of the SAE Hybrid J1772 Task Force in 2007 under SAE International, bringing together key automakers including General Motors, Ford, and Chrysler to address the growing need for standardized electric vehicle infrastructure.^[10] This collaborative effort shifted focus from earlier inductive charging approaches, which had been explored in the 1990s but deemed less efficient, toward conductive methods that enabled reliable Level 1 (120 V) and Level 2 (240 V) AC charging for plug-in electric vehicles (PEVs).^[11] The task force aimed to create a unified architecture encompassing physical connectors, electrical interfaces, and safety protocols to support widespread EV adoption amid rising environmental regulations and automaker commitments to electrification.^[10] Key milestones in the standardization process included concept finalization in early 2008, followed by extensive prototype testing throughout 2008 and 2009 to validate performance, interoperability, and safety under real-world conditions.^[12] These phases involved iterative evaluations of connector designs and signaling mechanisms, with input from utilities and equipment suppliers to ensure compatibility with existing electrical grids. Additionally, collaborations such as those with the ZigBee Alliance informed broader communication frameworks for PEV-smart grid interactions, laying groundwork for future vehicle-to-grid capabilities beyond basic charging control.^[13] The culmination of this work resulted in the first publication of SAE Recommended Practice J1772 in January 2010, which defined a single-phase AC system supporting up to 19.2 kW of power delivery for AC Level 2 charging while incorporating proximity detection and control pilot signaling for safe operation.^[10] Upon release, SAE J1772 rapidly emerged as the de facto standard for North American PEVs, with early adopters including the Nissan Leaf and Chevrolet Volt, both launched in late 2010 and equipped with the J1772 inlet for Level 1 and Level 2 charging.^[14] This swift integration by major manufacturers facilitated the rollout of compatible charging stations and accelerated consumer confidence in EV infrastructure, setting the stage for subsequent revisions while establishing conductive charging as the dominant method in the region.^[10]

Key Revisions

Earlier versions include the initial 1996 Recommended Practice and its 2001 adoption by the California Air Resources Board (CARB), which promoted early industry acceptance.^[6] The SAE J1772 standard underwent its foundational revision in January 2010 (J1772 JAN2010), establishing the baseline for conductive AC charging systems in North America. This update specified support for 120 V Level 1 charging at up to 16 A and 240 V Level 2 charging, with pilot signaling via a control pilot circuit using pulse-width modulation to communicate vehicle state, available current, and ventilation requirements between the electric vehicle supply equipment (EVSE) and the vehicle. The revision emphasized in-cable control and protection devices to ensure safe operation, drawing from earlier drafts to create a unified architecture for plug-in electric vehicles and hybrids.^[15] A major update arrived with the October 2017 revision (J1772_201710), which refined the standard, introduced formal definitions for DC charging levels (DC Level 1 and DC Level 2), enhanced fault detection protocols such as improved ground fault circuit interrupter (GFCI) integration and proximity pilot signaling for better error handling. Key technical improvements included stricter insulation requirements to prevent dielectric breakdown, refined ground fault monitoring to reduce shock hazards, and closer alignment with UL 2594 for EVSE safety testing and certification. These changes were motivated by industry feedback on the limitations of earlier versions in supporting faster charging and broader vehicle types.^[16]^[17] The revision process for SAE J1772 is managed by the SAE Hybrid and EV Standards Committee, which conducts reviews at least every five years—or more frequently as needed—incorporating input from automakers, charger manufacturers, and regulatory bodies to ensure relevance amid technological evolution. The 2017 update specifically responded to the surge in EV deployments, where higher power demands necessitated scalable charging without compromising interoperability or safety.^[16] As of November 2025, no major revisions have superseded the 2017 edition, though minor errata and clarifications have been issued periodically; for instance, a 2020 update addressed cable flexibility specifications to improve durability in real-world use, and the January 2024 revision (J1772_202401) refined terminology, corrected typographical errors, and better defined connector dimensions without altering core electrical parameters. These incremental changes maintain backward compatibility while supporting ongoing refinements.^[1]

Evolution to CCS and Beyond

The Combined Charging System (CCS) emerged in 2012 through the efforts of the Charging Interface Initiative (CharIN), a consortium founded by major automakers including Audi, BMW, Daimler, Ford, General Motors, Porsche, and Volkswagen to standardize EV charging.^[18] This system extended the existing SAE J1772 AC connector by incorporating two additional DC pins at the bottom, enabling high-power DC fast charging capabilities up to 350 kW while maintaining backward compatibility for AC charging.^[19] The design unified AC Level 1 and Level 2 charging with DC fast charging in a single port, addressing the need for versatile infrastructure as EV adoption grew.^[20] In 2013, SAE International formally adopted CCS1 as the North American variant, officially designating it as an extension of the J1772 standard under SAE J1772 Combo specifications. This integration supported ISO 15118 for vehicle-to-grid communication and smart charging protocols, allowing for automated authentication, billing, and energy management during sessions. The adoption solidified CCS1's role in enabling seamless DC fast charging across North American EVs, with power delivery up to 400 A and 1000 V, while preserving the J1772's AC functionality for residential and workplace use.^[20] The 2020s marked a pivotal shift with the rise of the North American Charging Standard (NACS), originally developed by Tesla. In June 2023, SAE announced its intent to standardize NACS as J3400, culminating in the publication of the J3400 technical information report by December 2023 and the full recommended practice by September 2024. This led to widespread production of adapters enabling J1772 and CCS-equipped vehicles to access NACS chargers, with major automakers like Ford, General Motors, Rivian, and Hyundai committing to native NACS ports on most new EV models starting in 2025.^[21] By mid-2025, NACS had become the dominant port for new EVs from these manufacturers, representing over 70% of incoming models, though J1772 persisted as the de facto AC charging standard for legacy and transitional systems.^[22] Key catalysts included the 2022 Biden administration initiative to establish unified national EV charging standards under the Bipartisan Infrastructure Law, aiming for a reliable 500,000-station network by 2030.^[23] In 2024, the National Electric Vehicle Infrastructure (NEVI) program reinforced CCS1 compatibility for federally funded projects through 2025, while issuing guidance for gradual NACS integration to support emerging vehicle fleets.^[24] Challenges persist in ensuring backward compatibility, as adapters bridge NACS and CCS systems but face supply chain constraints, with manufacturers like Ford reporting delays in adapter production due to surging demand and material shortages.^[25] These shifts prioritize NACS for its compact design and higher power handling, yet require ongoing investments in dual-standard infrastructure to avoid stranding existing J1772/CCS vehicles.^[26]

Connector and Physical Design

Type 1 Connector Specifications

The SAE J1772 Type 1 connector is a five-pin, round design standardized for conductive AC charging of electric vehicles in North America, featuring pins for L1 (line 1), L2/N (line 2 or neutral), ground (PE), control pilot (CP), and proximity pilot (PP).^[4]^[27] The connector body has a diameter of 43 mm, with the handle assembly measuring approximately 22 cm in length to facilitate ergonomic handling during connection.^[28]^[29] This compact form ensures compatibility with vehicle inlets while maintaining structural integrity under typical charging conditions. The housing is constructed from thermoplastic material rated UL 94 V-0 for flame retardancy, providing durability and resistance to environmental stressors such as heat and impact.^[30]^[31] Contacts are made of copper alloy with silver plating to enhance conductivity and prevent corrosion over repeated mating cycles.^[30]^[31] The pin configuration follows a specific layout: Pin 1 (top row, left) for L1 AC power (up to 240 V), Pin 2 (top row, right) for L2/N AC power, Pin 3 (bottom row, center) for ground, Pin 4 (bottom row, left) for PP detection, and Pin 5 (bottom row, right) for CP signaling.^[4]^[27]^[6] These assignments ensure safe power delivery and communication without cross-interference. Dimensional tolerances are tightly controlled per SAE specifications, with mating interfaces held to ±0.1 mm to guarantee reliable electrical contact and prevent misalignment during insertion.^[4] The assembly achieves an IP67 rating for ingress protection when mated, safeguarding against dust and water immersion up to 1 meter for 30 minutes.^[32]^[33] The vehicle inlet differs from the cable plug in its recessed mounting, which incorporates weatherproof seals and covers to protect against environmental exposure when not in use, enhancing longevity in outdoor installations.^[34]^[28]

Release and Locking Mechanisms

The SAE J1772 connector employs a solenoid-actuated latch in the vehicle inlet that engages upon full insertion of the connector, ensuring a secure attachment during charging. This locking mechanism is controlled by the vehicle's electronic control unit (ECU), which monitors the control pilot (CP) signal to initiate engagement once charging conditions are met. Normal release of the connector is achieved by pressing a manual button on the handle, which interrupts the proximity pilot circuit and signals the vehicle ECU to halt charging before disengaging the latch. In cases of power faults or emergencies, vehicles may provide additional release options, such as activation via the dashboard controls or key fob, allowing safe disconnection without physical force. To prevent partial insertion and potential damage, the connector design incorporates spring-loaded alignment pins that guide proper mating and require full engagement for the latch to activate. A torque limit of 5 Nm is specified during insertion to protect the connector components from excessive force. A safety interlock integrated into the system prohibits release of the latch while charging current is flowing; the ECU enforces this by maintaining the solenoid lock until current drops to zero. The locking and release mechanisms are engineered for high reliability, with the connector rated for 10,000 mate/unmate cycles under SAE testing conditions, ensuring long-term durability in typical use scenarios.^[32]

Compatibility with Other Systems

The SAE J1772 connector supports interoperability through various adapters that enable physical connection to household outlets and enhanced charging systems. Adapters converting J1772 plugs to NEMA 5-15 or 6-50 configurations allow users to connect to standard 120V or 240V household outlets for Level 1 charging, facilitating portable and emergency use without dedicated EVSE infrastructure.^[35] Similarly, CCS1 combo adapters integrate the J1772 AC pins with additional DC pins, permitting DC fast charging upgrades on vehicles equipped with a standard J1772 inlet without requiring inlet replacement.^[36] Mechanically, the J1772 design ensures reliable fit through a standardized mounting footprint established in the 2010 revision of the SAE standard, which defines precise dimensions for charge port inlets on vehicles and EVSE handles to guarantee consistent alignment and insertion.^[15] This footprint, typically measuring around 4-5 inches in key mounting points, allows for universal installation on North American EVs and charging stations. Weather-resistant seals, often integrated into the connector housing using thermoplastic elastomers, protect against moisture and debris in outdoor environments, maintaining IP44 or higher ingress protection ratings for prolonged exposure.^[37] In North American infrastructure, J1772 remains predominant, equipping the vast majority of public Level 2 charging stations as of early 2025, reflecting its role as the de facto standard for AC charging across major networks.^[38] Portable EVSE cables featuring J1772 plugs further enhance flexibility, allowing users to carry compact units that connect to standard outlets while providing a standardized vehicle interface. Despite its widespread adoption, J1772 exhibits limitations in global interoperability; it lacks direct physical compatibility with the European Type 2 (Mennekes) connector, necessitating adapters that bridge differing pin configurations and handle shapes for international travel or exports. For integration with the emerging North American Charging Standard (NACS), adapters typically add 2-5 cm to the overall connector length due to the inline conversion mechanism, potentially affecting ergonomics in tight spaces.^[39] The SAE J1772 standard mandates rigorous testing for mechanical reliability, requiring certified components to achieve 100% successful mating cycles over 10,000 insertions and extractions under normal conditions, ensuring consistent physical engagement without deformation or failure. This includes durability assessments for alignment tolerances and seal integrity, verified through accredited labs to confirm interoperability across compliant hardware.^[9]

Electrical and Charging Properties

Supported Charging Levels

The SAE J1772 standard enables alternating current (AC) charging for electric vehicles (EVs) and plug-in hybrid electric vehicles (PHEVs) through two distinct levels: Level 1 and Level 2, each tailored to different power supply capabilities and use cases.^[3] These levels utilize the five-pin J1772 connector to facilitate safe and standardized energy transfer from the electric vehicle supply equipment (EVSE) to the vehicle's onboard charger. Level 1 is suited for basic, opportunistic charging, while Level 2 supports faster, more practical recharging for daily needs.^[40] Level 1 charging operates on a 120 V single-phase AC supply with a maximum continuous current of 12 A, delivering up to 1.4 kW of power; it commonly employs a standard household NEMA 5-15 outlet via a portable adapter included with most vehicles.^[41] This level is ideal for overnight charging at home or topping up during short stops, though it results in slower energy delivery compared to higher levels.^[2] Typical charging rates under Level 1 add approximately 3-5 miles of range per hour for a standard sedan, depending on the vehicle's efficiency and battery state.^[3] Level 2 charging, in contrast, uses a 208-240 V single-phase AC supply capable of up to 80 A, providing a maximum power output of 19.2 kW through dedicated EVSE installations such as wall-mounted units or public stations.^[40] This level requires professional electrical upgrades for residential or commercial setups but enables significantly quicker charging sessions. For a typical sedan, Level 2 charging can add 20-25 miles of range per hour, making it the preferred option for home garages or workplace facilities.^[3] The J1772 standard exclusively supports AC charging modes and does not natively accommodate direct current (DC) fast charging, which necessitates the Combined Charging System (CCS) extension with additional DC pins. Actual charging performance at either level is ultimately constrained by the vehicle's onboard charger capacity, which converts AC to DC for the battery; many models, such as the Nissan Leaf or Chevrolet Bolt, are limited to 6.6 kW or 7.2 kW, respectively, preventing full utilization of higher-power Level 2 EVSE.^[42]

Power Ratings and Currents

The SAE J1772 standard specifies a maximum continuous current rating of 80 A at 240 V AC, delivering up to 19.2 kW of power for Level 2 charging applications. This rating ensures compatibility with single-phase AC systems commonly used in residential and commercial settings, allowing for efficient energy transfer while maintaining safety margins. The standard requires temperature monitoring in the connector and cable, with automatic current derating to prevent overheating. Current levels are communicated via pulse-width modulation (PWM) on the control pilot circuit, enabling discrete steps such as 6 A, 16 A, 32 A, 48 A, and 80 A to match the EVSE's capacity and the vehicle's onboard charger limits.^[43] These profiles allow dynamic adjustment during charging sessions, optimizing power delivery without exceeding infrastructure capabilities. The PWM duty cycle scales linearly with current in the AC Level 2 mode (up to 48 A), with higher levels using an extended scale for applications up to 80 A. Typical power factor is ≥0.95, reflecting efficiency in EV charging setups.^[1] To minimize voltage drop and ensure efficient power transfer, the standard limits cable length to a maximum of 7.6 m (25 ft) for 80 A operation, keeping the drop below 3% under nominal conditions.^[41] Power calculation follows the formula for single-phase AC systems:

P = V \times I \times \text{PF}

where P is power in kW, V is voltage in volts, I is current in amperes, and PF (power factor) is approximately 0.98, reflecting typical efficiency in EV charging setups. Overcurrent protection is mandated through circuit breakers sized at 125% of the rated continuous current, providing a safety buffer against transient loads while complying with National Electrical Code requirements integrated into the J1772 specifications. This derating ensures reliable operation across varying environmental conditions without risking equipment damage. The January 2024 revision enhanced safety features for thermal management at higher currents.^[1]

Voltage and Frequency

The SAE J1772 standard defines the AC voltage parameters for conductive charging systems to ensure compatibility with North American electrical grids. For AC Level 1 charging, the nominal voltage is 120 V RMS with a tolerance of ±10%. For AC Level 2 charging, the nominal voltage range spans 208 V to 240 V RMS, supporting both wye and delta power configurations commonly found in residential and commercial installations, also with a ±10% tolerance. The operating frequency is specified as 60 Hz with a tolerance of ±2% (ranging from 58.8 Hz to 61.2 Hz), aligning with the standard utility grid frequency in North America. SAE J1772 is limited to single-phase AC power delivery, eliminating the need for phase rotation synchronization requirements that apply to three-phase systems.^[43] To maintain reliable operation, the EV supply equipment (EVSE) must monitor and adapt to voltage fluctuations up to ±10% without interrupting the charging process, preventing unnecessary shutdowns due to minor grid variations. Insulation between the connector pins is rated at 1000 V RMS to provide robust electrical isolation and safety under normal operating conditions.

Safety and Protection Features

Ground Fault Detection

Ground fault detection in SAE J1772 systems is a critical safety mechanism integrated into the Electric Vehicle Supply Equipment (EVSE) to prevent electrical shock hazards by identifying leakage currents to ground during AC charging. This protection relies on a Ground Fault Circuit Interrupter (GFCI) system that continuously monitors the electrical circuit for imbalances indicative of faults.^[44] The GFCI incorporates a 6 mA trip threshold specifically designed for personnel protection in EV charging applications, with monitoring integrated into the Control Pilot (CP) circuit to provide real-time oversight of charging states and fault conditions.^[44]^[45] Detection occurs through current transformers that measure the difference between currents flowing in the L1 and L2 conductors (and neutral where applicable), triggering an alert if an imbalance exceeds the threshold, signaling a potential ground leakage path.^[46] In response to a detected fault, the EVSE interrupts power delivery within 40 ms to minimize risk, while the CP circuit transitions from State A (ready) to State B (interrupted), informing the vehicle to cease charging and safely disconnect.^[47] These requirements ensure compliance with key standards, including NEC Article 625, which mandates GFCI protection for EVSE receptacles and systems, and UL 2231, which outlines personnel protection testing and performance for EV charging circuits.^[48]^[49] For public charging stations, regular verification of the ground fault detection system is recommended as part of maintenance, following manufacturer guidelines and local codes, to confirm operational integrity, involving tests of the GFCI trip function and overall circuit protection.^[50]

Temperature Monitoring

Temperature monitoring in SAE J1772 systems ensures safe operation by detecting and mitigating heat buildup in connectors, cables, and associated components during charging. This feature is critical for preventing thermal damage, fire risks, and reduced component lifespan, particularly at higher power levels. Many SAE J1772-compatible systems incorporate dedicated sensors to provide real-time data, allowing dynamic adjustments to charging parameters. Sensors are integrated into the plug and handle, utilizing negative temperature coefficient (NTC) thermistors. These devices measure local temperatures at key points, such as contact interfaces and the cable entry, with resistance decreasing as temperature rises to enable precise detection.^[51] The thermistors connect to the Proximity Pilot (PP) circuit, which facilitates communication between the electric vehicle supply equipment (EVSE) and the vehicle.^[52] Operational limits are defined to maintain safety margins. Current derating begins if contact temperatures exceed a 50°C rise above ambient, reducing the charging rate to limit heat generation while sustaining power delivery. Shutdown occurs at 90°C to halt charging entirely and protect against insulation failure or melting.^[15] Monitoring occurs continuously via the PP circuit, where the vehicle electronic control unit (ECU) interprets sensor data and modulates the charge current in response, ensuring compliance with thermal thresholds.^[14] Cable design supports thermal management with insulation rated for 90°C continuous operation, providing durability under load while resisting degradation from heat exposure. The handle incorporates ventilation holes to promote airflow and dissipate heat from internal components, enhancing overall cooling efficiency.^[53] A 2015 recall of certain EVSE units, including those compatible with SAE J1772, addressed overheating issues in charging cords, prompting industry-wide scrutiny of thermal protections. This event contributed to enhancements in the 2017 revision of the standard, which refined thermal monitoring requirements for both AC and newly added DC charging modes to improve reliability at elevated power levels. The January 2024 revision further refined safety-related dimensions and updated references.^[54]^[55]^[1]

Interlocks and Fault Handling

The SAE J1772 standard employs hardware interlocks to enhance safety during connector mating and charging initiation. A mechanical switch integrated into the connector housing detects full insertion by completing a circuit only when the pins are fully engaged, thereby preventing the energization of power contacts in a partially connected state. This interlock de-energizes the connector and cable immediately upon any disconnection, mitigating risks of electrical shock or arcing.^[56]^[57] Fault conditions in SAE J1772 are communicated primarily through the control pilot (CP) circuit using voltage levels and pulse-width modulation (PWM) duty cycles to indicate 8 distinct states (A through H) for normal operation and errors. For instance, State H indicates a ventilation requirement via a +3 V level, while interruptions or abnormal signals (e.g., 0 V for State E or -12 V for State F) denote EVSE faults like overcurrent or internal errors. These states allow the electric vehicle supply equipment (EVSE) and vehicle to synchronize responses, ensuring charging halts promptly upon detection.^[43]^[58] Fault handling protocols in SAE J1772 distinguish between transient and permanent errors to maintain reliability. Transient faults, such as temporary communication glitches, trigger automated retry sequences where the EVSE attempts to re-establish the CP signal and handshake up to 20 times with 15-minute delays before requiring manual intervention. Permanent faults, including hardware failures or persistent ground issues, require manual reset of the EVSE, often via a power cycle or diagnostic interface, to clear latched protections.^[59]^[60] Diagnostics are facilitated by LED indicators on the EVSE, which provide visual cues for specific fault types to aid troubleshooting. A solid red LED typically signifies a ground fault or no-ground condition, while flashing patterns (e.g., three blinks) may indicate over-temperature or connector issues, enabling users or technicians to isolate problems without specialized tools.^[61]^[62] Overall, these features ensure SAE J1772's fault tolerance aligns with ISO 17409 requirements for conductive charging safety, incorporating redundant detection and response mechanisms to handle single-point failures without compromising user safety.^[63]^[64]

Communication Protocols

Control Pilot Circuit

The Control Pilot Circuit serves as the core signaling pathway in SAE J1772 for coordinating charge initiation, monitoring status, and ensuring safe operation between the electric vehicle supply equipment (EVSE) and the electric vehicle (EV). It employs a 1 kHz pulse-width modulated (PWM) signal generated by the EVSE and delivered to the EV through the dedicated control pilot pin in the connector. This signal operates on a base of ±12 V DC, oscillating between +12 V (positive state) and -12 V (negative state), with the PWM duty cycle—defined as the percentage of time the signal is in the positive state—directly encoding the EVSE's maximum available charging current.^[58]^[20] The circuit delineates six distinct operational states (A through F) based on the average DC voltage level measured by the EVSE on the control pilot line, which facilitates a structured handshake for charging. State A (standby) occurs when the EVSE is powered but no vehicle is detected, maintaining a +12 V DC level with no load. State B (vehicle connected) follows connector insertion, where the EV applies a load resulting in a +9 V to +6 V average voltage. State C (charging ready) indicates the EV is prepared for power transfer, dropping to +6 V to +3 V. State D (ventilation required) signals charging with mandatory ventilation, yielding +3 V to 0 V. State E (no power) reflects EVSE shutdown or power loss at -12 V DC, while State F (error) denotes a fault condition, also at -12 V DC but with specific PWM cessation. These states ensure sequential progression, preventing premature power application.^[65]^[66] Within the EV, the control pilot interface consists of a resistor-capacitor (RC) network connected between the pilot line and protective earth (PE) ground, enabling the vehicle to draw a controlled current of 2–16 mA to modulate the line's average voltage and signal its state back to the EVSE. This network typically includes fixed resistors switched in by the EV's controller; for instance, a 2740 Ω resistor for State B draws approximately 2.2 mA average current under the PWM signal, while an 882 Ω resistor for State C increases draw to about 6.8 mA. The RC filtering smooths the PWM for stable DC detection without introducing significant phase shift. A representative duty cycle of 50% on the EVSE's PWM signal corresponds to a maximum deliverable current of around 30 A, balancing typical Level 2 charging needs.^[58]^[67] The EV derives the EVSE's current capability from the measured PWM duty cycle, using a piecewise formula to compute the maximum allowable charging current I in amperes:

I = \begin{cases} \text{duty cycle (\%)} \times 0.6 & 10\% < \text{duty cycle} < 85\% \\ (\text{duty cycle (\%)} - 64) \times 2.5 & 85\% \leq \text{duty cycle} \leq 96\% \end{cases}

This scaling supports currents from 6 A (10% duty cycle) up to 80 A (96% duty cycle), allowing the EV to limit its demand accordingly and prevent overload. For example, a 50% duty cycle yields I = 50 \times 0.6 = 30 A.^[15]^[68] The charging handshake relies on the EV dynamically switching resistors in the control pilot circuit to transition states. Upon connector attachment, the EV initially engages a 1000 Ω to 2740 Ω resistor (nominal 2740 Ω) to enter State B, confirming connection without enabling power. Once the EV verifies internal readiness (e.g., battery conditions met), it switches to a lower 882 Ω resistor, pulling the average voltage into State C range and prompting the EVSE to close its main contactor for AC power delivery. If issues arise, the EV can revert to higher resistance or open the circuit to signal error (State F), halting charging. This resistor-based protocol provides a robust, low-cost analog handshake integral to J1772's safety architecture.^[65]^[58]

Proximity Pilot Detection

The Proximity Pilot Detection serves as a dedicated analog circuit in the SAE J1772 standard to verify connector insertion and identify the maximum current rating of the charging cable, ensuring compatibility and safety before initiating power transfer. It functions via a DC voltage loop supplied by the vehicle, typically starting at 5 V and dropping to near 0 V when connected, achieved through a pull-up resistor in the vehicle (often around 2.7 kΩ) connected to the Proximity Pilot (PP) pin. The cable assembly includes specific resistors between the PP pin and protective earth (PE) to encode the rating: 220 Ω for 32 A cables, 680 Ω for 20 A cables, and 1.5 kΩ for 13 A cables. These resistors form a voltage divider, enabling the vehicle's charging controller to measure the resulting voltage drop—approximately 0.4 V for 32 A, 1.0 V for 20 A, and 1.8 V for 13 A—and thereby confirm proper connection while automatically limiting the charging current to the cable's capacity.^[69] This detection mechanism enhances safety by prohibiting charging if the circuit loop is open, which occurs when the connector is unplugged or improperly seated, as the high voltage (near 5 V) signals an incomplete connection and halts power flow to prevent electrical hazards like arcing. The system integrates seamlessly with the vehicle's lock solenoid, activating it upon sensing the expected voltage range of 0.2–2.0 V to secure the connector mechanically during charging, as outlined in the SAE J1772 specification. For instance, pressing the cable's release button temporarily alters the circuit (often by paralleling an additional 330 Ω resistor), dropping the voltage further to prompt the vehicle to cease current draw before disconnection.^[58] A notable limitation of Proximity Pilot Detection is its reliance on fixed resistor values for current ratings, which does not allow for real-time or dynamic adjustments to charging parameters based on changing conditions. This static approach prioritizes simplicity and reliability but requires cable-specific hardware for different ampacities, distinguishing it from more advanced digital communication methods.

Powerline Communication (PLC)

Powerline communication (PLC) in SAE J1772 enables bidirectional digital data exchange between the electric vehicle (EV) and the electric vehicle supply equipment (EVSE) by superimposing high-frequency signals onto the control pilot (CP) circuit, facilitating advanced charging features beyond basic analog signaling. This layer supports protocols like ISO 15118, which allow for automated processes such as plug-and-charge authentication, where the EV and EVSE exchange digital certificates to verify identity and authorize billing without manual intervention; energy management, including dynamic adjustment of charging rates based on grid conditions; and session setup, encompassing negotiation of power limits and fault diagnostics. These functions enhance interoperability and support vehicle-to-grid (V2G) interactions, enabling EVs to respond to utility signals for load balancing.^[70] The technical foundation for J1772 PLC is outlined in SAE J2931/4, which specifies the physical and data-link layers using broadband PLC over the CP circuit, aligned with the IEEE 1901 standard for broadband over power line networks. Implementation involves orthogonal frequency-division multiplexing (OFDM) modulation to transmit data on the low-voltage CP line, typically at a 12 V DC offset, achieving data rates sufficient for ISO 15118 up to approximately 500 kbps in practical EV applications. To mitigate interference with the AC power lines, inline filters are employed at both the EV and EVSE ends, ensuring the high-frequency PLC signals (in the 1.3–16 MHz band) do not couple into the mains and disrupt power delivery. Error correction is provided by low-density parity-check (LDPC) codes, which enhance reliability in noisy environments typical of automotive wiring.^[71] Adoption of PLC in J1772 has been mandatory for Combined Charging System (CCS) DC fast charging since 2013, where it is integral to the ISO 15118 protocol stack for secure and efficient high-power sessions. For AC Level 1 and Level 2 charging under J1772, PLC remains optional but is increasingly integrated into smart charging infrastructure as of 2025, driven by the expansion of ISO 15118-compliant EVs and grid-responsive systems that enable features like scheduled charging and renewable energy optimization. This growth aligns with broader smart grid initiatives, where PLC facilitates seamless communication without additional wiring, promoting scalability in residential and public deployments.^[70]

Standards Landscape

Relationship to CCS

The Combined Charging System 1 (CCS1) serves as a direct technical extension of the SAE J1772 standard, enabling DC fast charging while maintaining compatibility with AC Level 1 and Level 2 charging. This integration is achieved by appending two additional pins for DC positive and negative power below the existing five-pin J1772 AC configuration, resulting in a total of seven pins designed to handle up to 1000 V and 500 A for DC delivery.^[72]^[73] Backward compatibility is a core feature, where AC charging operates using the J1772 pin subset without requiring vehicle modifications, allowing CCS1-equipped vehicles to interface seamlessly with standard J1772 AC chargers. In contrast, DC charging bypasses the vehicle's onboard AC-DC converter, supplying high-voltage DC directly to the battery pack, which necessitates the vehicle's internal DC-DC converter for any required voltage stepping if the charger's output does not match the battery's nominal voltage.^[3]^[74] CCS1 specifications support DC power delivery up to 350 kW under the 2025 standard revisions, facilitating significantly faster charging rates compared to AC-only systems. For high-current operations exceeding 200 A, liquid-cooled cables are standard, incorporating internal coolant channels to manage thermal loads and enable reliable performance at elevated power levels.^[75]^[76] System certification encompasses SAE J1772 compliance for the AC components alongside ISO 15118 protocols for DC handshake and communication, utilizing power line communication over the control pilot circuit to negotiate charging parameters securely.^[77]^[78] Key physical differences include the CCS1 inlet's larger dimensions, with a width of approximately 13 cm and height of 16 cm to accommodate the extended pin layout, in contrast to the more compact J1772 inlet. Furthermore, CCS1 employs no standalone DC cables; all implementations use combo cables that integrate both AC and DC functionalities within a single connector housing.^[79]^[80]^[81]

Competing Standards

The primary competitor to SAE J1772 and its CCS extension in North America is the North American Charging Standard (NACS), originally developed by Tesla and formalized as SAE J3400 in 2023. This 5-contact connector supports both AC and DC charging in a single design, enabling power delivery up to 1 MW for high-speed applications.^[82]^[83] Adapters facilitate compatibility, allowing J1772-equipped vehicles to access NACS infrastructure and vice versa, though seamless integration depends on vehicle and station capabilities. By July 2025, NACS commands over 54% of U.S. DC fast-charging ports, largely via Tesla's Supercharger network of more than 31,000 ports. As of November 2025, total public DC fast ports exceed 65,000, with industry forecasts indicating a rise to around 70% NACS share by year-end amid broad automaker adoption for 2025 models.^[84]^[85]^[86] On the global stage, CHAdeMO, a Japanese-originated DC fast-charging protocol, offers an alternative with capabilities up to 900 kW under its 3.0 iteration (ChaoJi), though most deployed units max out at 150 kW or below. Its adoption has waned significantly, representing less than 5% of worldwide DC fast chargers by 2025 as CCS and NACS proliferate.^[87]^[88] China's GB/T standard provides a combined AC/DC solution with dedicated connectors for each mode, supporting up to 1200 kW for DC, but it remains incompatible with J1772/CCS without specialized adapters or converters due to distinct pinouts and protocols. GB/T holds dominant sway in China, capturing over 60% of the global connector market in 2025, yet its international footprint is minimal outside Asia.^[89]^[90] In the U.S., J1772/CCS retains about 45% of DC fast ports as of mid-2025, reflecting a contraction from prior years amid NACS momentum and declining to around 40% by late 2025. The National Electric Vehicle Infrastructure (NEVI) program, administering federal funds, now mandates dual CCS and NACS support at new stations to promote interoperability.^[91]^[92]^[93] SAE J1772 excels in simplicity for AC charging scenarios, leveraging its straightforward 5-pin layout for reliable Level 2 deployments at homes and offices without the added complexity of DC pins. NACS, however, advantages DC-focused use with its compact, lightweight form factor that enhances portability and supports denser high-power installations.^[94]^[95]

International Adoption and Equivalents

SAE J1772 has achieved dominant adoption in North America, where it powers approximately 93% of public AC charging stations as of 2025, primarily for Level 1 and Level 2 charging. This prevalence stems from its establishment as the de facto standard for non-Tesla electric vehicles since the early 2010s, enabling widespread compatibility across major networks like ChargePoint. For DC fast charging, the CCS1 variant— which incorporates J1772 pins for AC alongside additional DC pins— accounts for about 40% of public stations, reflecting its role in supporting faster charging for compatible vehicles while coexisting with emerging alternatives like NACS.^[96]^[97]^[98] Internationally, J1772 is equivalent to the IEC 62196 Type 1 connector, which shares its five-pin design and single-phase AC capabilities, and has seen adoption in regions like Japan for residential and public AC charging. In Japan, Type 1 connectors align directly with J1772 specifications, supporting up to 7.7 kW charging and integrating seamlessly with the country's 100V/200V grid systems. Limited use of Type 1 equivalents appears in Israel, often via imported North American vehicles, though local infrastructure favors other standards. In contrast, Europe predominantly employs the IEC 62196 Type 2 (Mennekes) connector for AC charging, which extends J1772's principles to three-phase power delivery up to 22 kW, but differs in pin configuration to accommodate 230V/400V systems.^[99]^[100]^[101]^[102] Adoption of J1772 outside North America remains limited in the European Union, where CCS2—building on Type 2 for both AC and DC— is the preferred standard, comprising over 90% of public AC and fast-charging infrastructure due to regulatory mandates under the Alternative Fuels Infrastructure Regulation (AFIR). In South Korea, J1772-compatible charging is growing through adapters that bridge Type 1 inlets on imported vehicles to local CCS1 or GB/T stations, facilitating AC charging at up to 7 kW amid the country's rapid EV expansion. These adapters address compatibility gaps, enabling North American-spec vehicles to access the network without full infrastructure overhaul.^[103]^[104]^[105] As of 2025, the ISO 15118 standard has unified communication protocols for vehicle-to-grid interactions and Plug & Charge functionality across global chargers, promoting interoperability regardless of physical connector. However, physical standards continue to diverge regionally, with J1772 and Type 1 accounting for roughly 10% of global AC charging capacity, concentrated in North America and select Asian markets. This fragmentation persists despite ISO efforts, as local grids and vehicle designs prioritize region-specific plugs.^[106]^[107] Key challenges to broader J1772 international use include voltage and phase mismatches; for instance, Europe's 230V single-phase or 400V three-phase grids often require step-down transformers or adapters for North American vehicles rated at 120V/240V, potentially reducing charging efficiency and adding complexity to cross-border travel. Such adaptations can limit power output to 3-7 kW, compared to native Type 2's higher rates, and raise safety concerns if not properly rated.^[108]^[109]

References

[1]
J1772_202401 : SAE Electric Vehicle and Plug-in Hybrid Electric ...
30-day returnsThe SAE J1772 document has been updated to refine the language of the standard; better define the AC connector dimensions; correct typogriphical ...
[2]
Charger Types and Speeds | US Department of Transportation
Jan 31, 2025 · A Combined Charging System (CCS) connector uses the J1772 charging inlet, which has. CHAdeMO connector. Schematic of a CHAdeMO connector plug.Direct Current Fast Charging... · Ev Charging Minimum... · Overview Of Ev Chargers
[3]
Electric Vehicle Charging Stations - Alternative Fuels Data Center
The Combined Charging System (CCS), also known as the SAE J1772 combo, charge port on a vehicle can be used to accept charge with Level 1, Level 2, or DC fast ...
[4]
J1772_201710 : SAE Electric Vehicle and Plug in Hybrid Electric ...
30-day returnsThis SAE Standard covers the general physical, electrical, functional and performance requirements to facilitate conductive charging of EV/PHEV vehicles in ...
[5]
j1772_199610 sae electric vehicle conductive charge coupler
30-day returnsThis SAE Recommended Practice covers the general physical, electrical, and performance requirements for the electric vehicle conductive charging system and ...
[6]
https://www.cablematters.com/Blog/Power/what-is-j1772
[7]
SAE J1772 Electrical Connector for Electric Vehicle
SAE J1772 was adopted on January 14, 2010 by the SAE Motor Vehicle Council. The companies participating in or supporting the revised -2009 standard include GM, ...
[8]
SAE J1772 Standard Testing - Intertek
The revised SAE J1772 standard provides design and safety guidelines for charging controls and connectors, and serves as a consensus standard for both AC and ...
[9]
[PDF] Codes and Standards to Support Vehicle Electrification
May 15, 2012 · ▫ SAE J1772 AC Coupler Standard published January. 2010. ▫ SAE J1772-v5 DC Coupler standard final publication July 2012. ▫ UL coupler ...Missing: initial | Show results with:initial
[10]
Development of the SAE J1772 Standard of Electric Vehicle Charger
Then, the California Air Resources Board also formulated the SAE J1772-2001 standard in June 2001 as the standard for electric vehicle charging in California.
[11]
Industry Nears Plug Standard for EVs in North America | WardsAuto
Apr 22, 2009 · A concept was settled on in January 2008, and the connector has been in testing since late last year. Kissel expects that process to be ...
[12]
ZigBee Alliance and SAE Accelerate Electric Vehicle Connection to ...
Jan 28, 2011 · Their efforts will make ZigBee Smart Energy the preferred technology supporting Plug-In Electric Vehicles (PEV) and enabling essential vehicle ...
[13]
Understanding SAE J1772: Technical Insights for Charger Testing
Historical Development and Industry Impact. SAE J1772 was originally introduced in the early 2000s under the impetus of the California Air Resources Board ( ...
[14]
[PDF] SURFACE VEHICLE RECOMMENDED PRACTICE
SAE. J1772 Revised JAN2010. Page 5 of 51. 2.1.4 International Electrotechnical Commission Publication. Available from International Electrotechnical Commission ...
[15]
[PDF] SAE J1772-2017.pdf - SURFACE VEHICLE STANDARD
The SAE J1772 document has been updated to refine the language of the standard, correct errors found in the previous version and to reflect the addition of ...
[16]
Electric Vehicle Charging Systems: Comprehensive Review - MDPI
Accordingly, the October 2017 revision of the SAE J1772 standard outlines four charging levels: AC Level 1, AC Level 2, DC Level 1, and DC Level 2 [65].<|separator|>
[17]
CharIN – Empowering the next level of green mobility and energy.
### Summary of CharIN Founding and CCS Introduction in 2012
[18]
How to implement CCS? - CharIN
It has created this Design Guide to assist other companies with an interest in electric mobility – including carmakers, municipal power utilities, manufacturers ...Missing: founding 2012 introduction
[19]
[PDF] An Introduction to the SAE J1772 and CCS EV Charging Interfaces
The SAE's J1772 standard defines the physical, electrical, communication protocol, and performance requirements for the EV conductive charge system and coupler ...
[20]
The Great NACS Migration: Here's Who Switches to Tesla's ...
Sep 5, 2025 · Some automakers like Ford and General Motors have decided to start a partnership with Tesla to license out NACS ports for their vehicles in 2025.Missing: development | Show results with:development
[21]
What Is the North American Charging Standard? - Aptiv
Aug 11, 2023 · In June 2023, SAE International announced that it would standardize the connector, helping to ensure consistency across the industry. The most ...
[22]
Biden-Harris Administration Takes Key Step Forward in Building a ...
Jun 9, 2022 · These new ground rules will help create a network of EV chargers across the country that are convenient, affordable, reliable and accessible for all Americans.
[23]
National Electric Vehicle Infrastructure Standards and Requirements
Feb 28, 2023 · This final rule also establishes that each charging port must have an average annual uptime greater than 97 percent. Other Federal Requirements.
[24]
Ford Leans on NACS Adapter Supplier To Cope With Supply Chain ...
Nov 1, 2024 · The adapters make it easy to charge on Tesla's network, and many automakers have made moves to install NACS ports at the factory going forward.Missing: backward shifts
[25]
[PDF] Recommended Actions to Improve Adapter Safety
Firstly, there is a need to standardize the new connector type to ensure it is interoperable, safe, and reliable. Second, existing CCS EV drivers need a way to ...
[26]
J1772 Gen 3 Electric Vehicle (EV) Charging Connector - ITT Cannon
The ITT Cannon J1772 Generation 3 Electric Vehicle Charging Connector is a vehicle coupler built in accordance with the SAE standard for AC level 1 and level 2 ...Missing: mm | Show results with:mm
[27]
Chargers & Accessories :: SAE J1772 Charge Port
In stock 30-day returnsThis is a J1772 charge inlet port configured for Type 1 EV Supply Equipment (EVSE). · J1772 is a worldwide standard for communication between vehicles and EVSEs.
[28]
[PDF] Volex SAE J1772 GEN 1 AC Charging Cable
DIMENSIONS: CHARGING CONNECTOR. Width. 50.4 mm. Height. 90 mm. Depth. 215.6 mm ... SAE J1772 GEN 1 MECHANICAL DRAWING. Contact us at sales@volex.com for ...
[29]
SAE J1772 EV Charging Connector Plug - Evlithium
Material application. 1. Case Material: thermoplastic flammability rating UL94V-0. 2. Cuill: copper alloy surface silver-plated. 3. seals: rubber or silicone. 4 ...
[30]
SAE J1772 Plug AC Charging Connector EV Charger 16A 240V ...
Contact Material. Copper Alloy ; Contact Finish. Silver Plating ; Flammability. UL94 V-0 ; Ingress Protection. IP65 ; Operating Temperature. -30℃~50℃ ...Missing: thermoplastic | Show results with:thermoplastic
[31]
ER Series SAE J1772 - Amphenol Industrial Operations
The ER Series SAE J1772 supports a wide range of power needs, with current ratings of 20A, 32A, 40A, 50A, and up to 80A at a voltage capacity of 250V AC. These ...<|control11|><|separator|>
[32]
Gen 3 J1772 EV Connectors - ITT Cannon
Compliant with the stringent SAE standards for AC level 1 and level 2 charging systems, the J1772 Generation 3 Connector is engineered to perfection. Key ...Missing: tolerance ±0.1 mm
[33]
J1772 EV Charging Inlet Socket Vehicle Charger Connector ... - eBay
In stock $24 deliveryJ1772 EV Charging Inlet Socket Vehicle Charger Connector Weatherproof Door 32AMP ... 4 interest-free payments of $13.50 available with 4 interest-free payments of ...Missing: recessed | Show results with:recessed
[34]
J1772 to NEMA 5-15 Connector, EV Charger Adapter for E-bike ...
In stock Free deliveryWith its J1772 to Nema 15-5 configuration, you can connect your electric vehicle to any 240-volt compatible household charger while on the road.
[35]
Amazon.com: YIGPAIPO J1772 and CCS Adapter - 2 in 1 Works with ...
The perfect charging solution for your Tesla. It allows you to connect to both CCS DC Fast Charging stations and J1772 AC charging stations.
[36]
SAE J1772 Plug/Connector 32A for EV Charging - Jpson.com
$$69.00Materials. Shell Material: Thermo Plastic ( Insulator inflammability UL94 VO); Contact Pin: Copper alloy, silver or nickel plating; Sealing gasket: rubber or ...
[37]
Largest AC Charging Networks in the US: January 2025
Jan 6, 2025 · ... Level 2 points are equipped with SAE J1772 plugs. This will gradually change as part of the transition from the CCS1/J1772 to the NACS as ...
[38]
https://evchargingstations.com/chargingnews/largest-ac-charging-networks-in-the-us-january-2025/
[39]
[PDF] Electric Vehicle Charging Levels and Requirements Overview
Dec 15, 2010 · • Published SAE Standards. – SAE J1772 Surface Vehicle Recommended Practice ... • First Published October, 1996. • Revised December, 2009 (AC ...Missing: initial | Show results with:initial
[40]
[PDF] Electric Vehicle Charger Selection Guide
1-2/J1772, 1-2/120V connections. 208/240VAC; 40A ... This is different from the Level 2. SAE J1772 charging sockets common to most public chargers in the US.
[41]
How EV Charging Works & What You Need To Know
Aug 11, 2023 · Full battery electric vehicles typically have a Level 2 acceptance rate of at least 6.6 kW, with newer models offering a 9 to 12 kW acceptance ...Missing: onboard capacity
[42]
[PDF] SURFACE VEHICLE STANDARD - Regulations.gov
The SAE J1772 document has been updated to refine the language of the standard, correct errors found in the previous version and to reflect the addition of ...
[43]
Electrical Safety for Electric Vehicle Charging - Bender Inc.
This charging cable must have an integrated monitoring system capable of triggering a 6 mA ground fault. These are known as charge current interrupting devices ...Missing: detection | Show results with:detection
[44]
https://www.benderinc.com/solutions/electric-vehicles/charging-stations-evse/
[45]
[PDF] EV Charging Solutions - Littelfuse
Current Transformer. Offers ground-fault detection and protection. SE-704. Specifically designed for low-level detection; flux conditioner is included to ...
[46]
[PDF] Electrical Safety Solutions for EV/EVSE - Bender Inc.
"The minimum insulation resistance of the on-board network must be maintained throughout the service life and under all operating conditions". The perfect ...
[47]
https://www.benderinc.com/fileadmin/content/BenderGroup/Documents/Article/en/EV_Brochure.pdf
[48]
UL 2231-1 Testing for Electric Vehicle Charging Systems
This standard emphasizes the need for advanced fault detection mechanisms, ensuring that any anomalies in the electrical current are immediately detected.Missing: J1772 transformers
[49]
[PDF] CIRSA HAZARD ALERT
Inspect the station itself for any damage. • Test ground fault protection (GFI) and emergency stops. • Check the EV cable and connector for cracks, broken ...Missing: EVSE testing annual verification
[50]
[PDF] KEY FEATURES: Compliant with: SAE J1772 IEC 62196-3 UL2251
Temperature sensor: N: NTC (Unit in mm). P: PT1000 (Unit in mm). N/A: No sensor. Cable length: LXXXX: Cable length (Unit in mm). Cable accessories: XXXX: Cable ...Missing: 10k | Show results with:10k
[51]
https://www.amphenol.co.jp/military/catalog/CCS1.pdf
[52]
[PDF] sdg&e electric vehicle supply equipment standards - SDGE
Oct 9, 2020 · CORD LENGTH: 18 FEET MINIMUM, 25 FEET MAXIMUM. ENVIRONMENT: OPERATING TEMPERATURE: -30 TO 50 CELSIUS (-22 TO 122 FAHRENHEIT) ... 75°C, 90°C.
[53]
Ford recalls 50,000 charging cables delivered with its electric ...
Aug 22, 2018 · Ford is issuing a recall for approximately 50,000 120-volt convenience charge cords originally provided with select 2012-15 Ford Focus Electric, ...
[54]
https://electrek.co/2018/08/22/ford-recalls-charging-cables-electric-vehicles/
[55]
https://www.sae.org/standards/content/j1772_201710/
[56]
[PDF] INSTALLATION GUIDE FOR ELECTRIC VEHICLE SUPPLY ...
Electric vehicle supply equipment shall be provided with an interlock that de-energizes the electric vehicle connector and its cable whenever the electrical ...
[57]
[PDF] J1772 / OpenEVSE
The J1772 Pilot is a 1khz +12V to -12V square wave, the voltage defines the state. The EV adds resistance pilot to Ground to vary the voltage. The EVSE reads ...Missing: 2010 | Show results with:2010
[58]
[PDF] Recommended Practice: Seamless Retry for Electric Vehicle Charging
Dec 1, 2024 · SAE J1772. Revision. J1772_202401. Presents a charging session “restart” mechanism where digital communications can be restarted after an error ...
[59]
[PDF] Recommended Practice: Seamless Retry for Electric Vehicle Charging
Both of these documents mention that this “restart” mechanism can be used for failed sessions in addition to paused sessions.
[60]
[PDF] VersiCharge™ SG Electric vehicle charging station
The VersiCharge charger has been designed to self-indicate which type of fault has occurred. A fault is indicated by a solid red halo, a blinking red halo, and/ ...
[61]
[PDF] Level 2 Electric Vehicle Supply Equipment Charging Station
Refer to the vehicle owner's manual to determine if the vehicle is equipped with an SAE J1772™ compliant charge port. ... The Fault indicator LED remains flashing ...
[62]
[PDF] and Three-Wheelers and Charging Infrastructure in Pakistan - NREL
The details of the overload protection are given in ISO 17409:2020 (ISO 2020b). ... This was chosen over the SAE J1772 standard, which is consistent with other ...
[63]
ISO 17409:2020 - Electrically propelled road vehicles
In stock 2–5 day deliveryThis document specifies electric safety requirements for conductive connection of electrically propelled road vehicles to external electric circuits.Missing: SAE J1772 tolerance<|control11|><|separator|>
[64]
How It Works: L2 EV Chargers - PowerFlex Doc Hub
Feb 7, 2024 · SAE J1772 and Tesla are common L2 connectors in North America. The ... Voltage on PP pin. Not connected, 4.5V. Release latch pressed, 3.0V.Introduction · The Charging Session · J1772 Control Pilot Signal &...
[65]
How does EVSE work? What are control pilot and proximity contact ...
The control pilot signal enables basic communication between the EVSE ... Besides states B, C and D, several other states are defined: A – electric ...Missing: SAE J1772 ABCDEF
[66]
[PDF] Implementing SAE JI772 Pilot Wire System in EV Charging Station ...
• Rise time and fall time < 2μs per SAE J1772 Specifications. How High-Voltage Comparators benefit the system. • Wide operating voltage of up to 40V (±20V) ...
[67]
[PDF] ENERGY STAR EVSE Draft 3 Test Method
Table 3: Available Current Calculation from Control Pilot Duty Cycle (SAE J1772). Duty Cycle (%). Available Current (A). 10% < Duty Cycle < 85%. % Duty Cycle x ...
[68]
[PDF] Codes and Standards Support for Vehicle Electrification | Energy
May 14, 2013 · SAE J2931 Powerline Communication over the 1 kHz pilot wire requires a broad range of coexistence, crosstalk and compatibility rigorous yet ...
[69]
Overview of North American Charging Standards for New Energy ...
Aug 4, 2025 · CCS1 builds on J1772 by adding a two-pin DC connector, creating a split upper and lower design. The DC side supports a maximum of 1000V/400A, ...Missing: 2013 | Show results with:2013
[70]
J1772 vs CCS: 5 Key Differences in EV Charging Adapters
Jul 4, 2025 · The J1772 plug can be inserted into the interface of the CCS charger, but it only supports AC charging and does not have DC fast charging function.Missing: approval 2023
[71]
https://saemobilus.sae.org/standards/content/j2931/4_202305/
[72]
CCS1 vs CCS2: Which Fast Charging Standard is Right for You
Jun 4, 2025 · For DC fast charging, both CCS1 and CCS2 charging speeds support 50-350kW DC fast charging, with nearly identical performance in this regard.
[73]
EV Charging Connector Types: A Complete Guide - Power-Sonic
The SAE J1772 connector, also known as a J Plug or Type 1 connector, is a charging standard used primarily in North America and Japan. It features five pins and ...Missing: physical | Show results with:physical
[74]
EV Charging Station Connector Requirements: ISO 15118 ...
Oct 3, 2024 · The SAE J1772 standard defines a type 1 connector with five connections (Figure 1). ... The SAE J3068 standard defines this connector as ...
[75]
What is ISO 15118? - Switch EV
Oct 11, 2021 · As part of the Combined Charging System (CCS), ISO 15118 is a communication protocol covering all use cases for charging electric vehicles ...
[76]
CCS1 Inlet - Greatenergy Inc.
The CCS Type 1 was developed for the North American market and is a extension of the SAE J1772 connectors with two additional direct current (DC) contacts.Missing: 21 cm
[77]
SAE J1772 vs CCS: Essential Insights for EV Owners - EVB Charger
Oct 16, 2024 · A J1772 charger, also called SAE J1772, serves as the standard charging connector for electric vehicles in North America. It supports Level 1 ...
[78]
SAE J3400 Charging Connector
NACS can also be used for AC Level 1 and Level 2 charging and is compatible with the J1772 connector for these charging speeds through an adapter. In May 2023, ...Missing: approval | Show results with:approval
[79]
SAE International | Advancing mobility knowledge and solutions
**Summary of SAE J3400 Standard (May 2023):**
[80]
Largest DC Fast-Charging Networks in the US: July 2025
Jul 1, 2025 · Tesla Superchargers: 31,990 ports (a 54.6% share) · Electrify America: 4,894 ports (an 8.3% share) · ChargePoint: 4,463 ports (a 7.6% share) · EVgo ...
[81]
EV Charging Index 2025: Expert insights from North America
Oct 1, 2025 · The market continues to shift to the NACS – formerly known as the Tesla standard – for both new and existing chargers. This means Tesla and ...
[82]
CHAdeMO 3.0 released: the first publication of ChaoJi, the new plug ...
This latest version of CHAdeMO protocol enables DC charging with the power over 500kW (maximum current 600A), while ensuring the connector to be light and ...
[83]
What is CHAdeMO and Is It Still Relevant in 2025? - EV Chargers
Aug 31, 2025 · Global Adoption Rates and Infrastructure. CHAdeMO infrastructure represents approximately 18,000 charging points worldwide as of 2024, with ...
[84]
EV Charging Station Market Size, Share & Future Trends, 2032
The global EV charging station market is set at US$ 31.1 Billion in 2025 and projected to reach US$ 113.4 Billion by 2032, growing at a 20.3% CAGR.
[85]
EV Charger Connectors Explained: Types, How They Work, and ...
Oct 13, 2025 · The SAE J1772 connector supports both Level 1 (120V) and Level 2 (240V) AC charging, with a maximum output of around 19.2 kW. It uses a control ...
[86]
https://evchargingstations.com/chargingnews/there-are-over-65k-public-dc-fast-charging-stalls-in-the-us/
[87]
https://www.chademo.com/chademo3-0
[88]
https://www.bestchargers.co.uk/what-is-chademo-and-is-it-still-relevant-in-2025/
[89]
NACS vs. J1772: Which EV Charger Is Best? | ChargerPro
Feb 22, 2025 · Compact Design: NACS connectors are smaller, sleeker, and easier to handle compared to J1772. · Fast Charging: With Tesla's proprietary ...
[90]
US Now Has Over 170,000 Public AC Charging Stalls
Oct 15, 2025 · In North America, Tesla Destination points are equipped with ... charging points are equipped with SAE J1772 plugs (almost 159,000 or 93%).Missing: percentage | Show results with:percentage
[91]
North America DC Charger Market Size, Share & Analysis [2040]
The North America DC Charger market size is projected to grow from $1040.6 million in 2025 to $26152.5 million by 2040, exhibiting a CAGR of 24.0%
[92]
Electric Vehicle Charging Infrastructure Market Size to Hit USD ...
The global electric vehicle charging infrastructure market size is calculated at USD 47.61 billion in 2025 and is forecasted to reach around USD 415.58 billion ...
[93]
https://www.evconnect.com/blog/nevi-program-2025-updates
[94]
Exploring Global EV Charging Connector Types - SINBON
Type 1. J1772 type, set up by SAE in 2010, is a widely used charging specification in North America, Japan, and Taiwan. AC charging cable type 2. Type2 AC ...
[95]
SAE J1772 vs IEC 62196: What is the Difference? - BESEN
The SAE J1772 connector, also known as the J plug or Type 1 connector, serves as the North American standard for EV conductive charging. This connector supports ...
[96]
Alleviating range anxiety with IEC Standards for e-mobility
Apr 18, 2023 · The IEC 61851 Standards specify the DC and AC charging infrastructures and go hand in hand with IEC 62196 series.
[97]
EV Charging Standards and Protocols - Driivz
Sep 21, 2024 · The Combined Charging System Standard (CCS) covers several aspects of EV charging ... (SAE J1772) connectors are mostly used for AC home charging ...
[98]
Understanding EV Charger Connector Types - Injet New Energy
Dec 5, 2024 · The CCS standard includes two versions: CCS1, commonly used in North America and South Korea, and CCS2, prevalent in Europe and other regions.
[99]
https://evniculus.eu/pages/ev-charging-adapters-1
[100]
Electric vehicle charging – Global EV Outlook 2025 – Analysis - IEA
In 2024, more than 1.3 million public charging points were added to the global stock, representing an increase of more than 30% compared to the previous year.Missing: standard | Show results with:standard
[101]
AFIR & ISO 15118: New obligation for AC charging stations from 2026
New AFIR obligations require EN ISO 15118 support for AC charging stations: 1/8/2026 for public, and 1/1/2027 for public and private Mode 3 charging points.
[102]
https://www.iec.ch/blog/alleviating-range-anxiety-iec-standards-e-mobility
[103]
The Five Electric Vehicle Charging Standards Worldwide | Bonnen
Feb 18, 2024 · The main difference is that the standard household electricity in Europe is 230 volts, which is almost twice the voltage used in North America, ...2. Chinese Charging... · 4. European Charging... · 5. Japanese Charging...