Fact-checked by Grok 2 weeks ago

Single-wire earth return

Single-wire earth return (SWER), also known as single-wire ground return, is a single-phase electrical distribution system that employs a single overhead conductor to transmit power, with the Earth acting as the conductive return path for the current, thereby eliminating the need for a dedicated neutral wire.^[1]^[2] This approach isolates the system from the main grid via an isolating transformer at the source to prevent interference and ensure safety, typically operating at medium voltages such as 12.7 kV or 19.1 kV before stepping down to low voltage (e.g., 240 V) at distribution transformers for end users.^[1] Invented by New Zealand engineer Lloyd Mandeno in the early 1920s while serving as Tauranga's Borough Engineer, SWER was first implemented in 1925 by the Tauranga Electric Power Board, marking the world's inaugural commercial use of the technology.^[3]^[4] Mandeno's design, initially nicknamed "Mandeno’s clothesline" for its minimalist appearance, addressed the challenges of extending electricity to remote rural areas with low population densities, where traditional multi-conductor lines proved economically unviable.^[3] The system gained traction post-World War II, with widespread adoption in New Zealand's Northland and central North Island regions, and later internationally in countries including Australia, South Africa, India, and parts of South America and Africa.^[3]^[5] SWER systems are engineered for cost efficiency in low-demand scenarios, requiring approximately 2.5 poles per kilometer compared to seven for conventional lines, resulting in construction costs about 50% lower than two-wire single-phase setups and 70% lower than three-phase systems.^[1]^[2] Power delivery is limited to under 0.5 kVA per kilometer, with a maximum of around 3.5 kVA per customer, making it ideal for sparse agricultural or residential loads but unsuitable for industrial three-phase applications without additional phase converters.^[1] Maintenance is also reduced by roughly 50% due to the simplified infrastructure, though challenges include higher outage rates—such as four times more minutes of supply interruption in some regions—and potential risks like surface potential gradients that could affect humans or livestock near grounding points, as well as increased bushfire ignition risk in dry areas if not properly maintained.^[1] Today, SWER remains a vital tool for rural electrification, for example, Ergon Energy operates about 64,000 km serving approximately 4% of its customers (around 26,000), with a national total exceeding 200,000 km in Australia as of the early 2020s, and ongoing exploration of its potential in developing regions like Africa to accelerate power access via policy adaptations.^[1]^[5] In recent years, some networks have begun transitioning parts of SWER to stand-alone power systems for better reliability, while enhancements continue to address safety and integration with renewables. Despite limitations in capacity and reliability, its economic advantages continue to make it a preferred solution for extending grid reach in underserved areas, often complemented by modern enhancements like improved grounding and monitoring to mitigate interference with telecommunications.^[3]^[2]

Overview and History

Definition and Basic Concept

Single-wire earth return (SWER) is a single-phase electrical distribution system that employs one overhead conductor to carry the active phase current, with the earth serving as the neutral return path to complete the circuit.^[6] This design minimizes infrastructure requirements by eliminating the need for a dedicated neutral wire, making it distinct from conventional multi-wire systems that use separate conductors for both active and neutral phases.^[1] Unlike early ground-return telegraph lines, which operated on low-power direct current for signaling, SWER is an alternating current (AC) power distribution method adapted for modern electrical supply.^[6] The primary purpose of SWER systems is to facilitate cost-effective rural electrification in sparsely populated areas, particularly for isolated loads such as water pumps, irrigation systems, and small communities where traditional grid extension would be uneconomical.^[7] These systems are best suited for low load densities, typically below 0.5 kVA per kilometer of line, with individual customer demands rarely exceeding 3.5 kVA.^[1] By leveraging the earth's conductivity, SWER reduces material and installation costs, enabling power delivery over long distances in regions with minimal expected load growth.^[8] Key components of a SWER system include a single insulated overhead wire, typically made of aluminum conductor steel-reinforced (ACSR), earth electrodes or stakes at distribution transformer locations to ensure low-resistance grounding (often ≤5 ohms), and isolating transformers at the supply end to separate the SWER line from the main grid and prevent ground current loops.^[9] Distribution transformers, rated at common sizes like 5 kVA, 10 kVA, or 25 kVA, step down the voltage for end-user consumption, while the isolating transformer—often up to 300 kVA—provides galvanic isolation and voltage adjustment.^[1] SWER lines typically operate at medium-voltage levels such as 12.7 kV or 19.1 kV line-to-earth, derived from connections to 22 kV or 33 kV three-phase grids, respectively, supporting power ratings up to 300 kVA per isolating transformer depending on line length and soil resistivity.^[1] This configuration allows for efficient delivery in low-density environments but requires careful earthing to maintain performance and safety.^[9]

Historical Development

The concept of single-wire earth return originated in the 1840s with electrical telegraph systems, where a single overhead wire transmitted signals and the earth served as the return path to complete the circuit, enabling efficient long-distance communication without a second wire.^[10] The modern single-wire earth return (SWER) distribution system for electrical power was developed in the early 1920s by New Zealand engineer Lloyd Mandeno to address the high costs of conventional wiring in sparsely populated rural areas. The first practical installations occurred in 1925 near Tauranga, New Zealand, marking the initial application of SWER for rural power supply. Post-1920s expansion saw SWER gain traction in New Zealand and Australia, where it proved ideal for extending electricity to remote farms and communities.^[11] In Australia, adoption accelerated in the 1950s as part of rural electrification initiatives, leading to extensive deployment in outback regions.^[1] By the late 20th century, over 200,000 km of SWER lines were operational, predominantly in Australia, underscoring its role in cost-effective grid extension.^[1] Key milestones included a 1981 prototype in Alaska, where an 8.5-mile high-power SWER line at 80 kV connected a diesel plant in Bethel to Napakiak, validating the system's viability on permafrost terrain with lightweight infrastructure.^[12] SWER's economical design influenced mid-20th-century global rural electrification standards, promoting its use in developing regions for low-density power distribution.^[8]

Technical Principles

Operating Principle

In a single-wire earth return (SWER) system, electrical power is distributed using a single overhead conductor to carry the active current from the source to the load, while the return current flows back through the earth, leveraging the soil's conductivity as the neutral path.^[13] This return path is facilitated by grounding electrodes at key points, such as the isolating transformer and distribution transformers, which connect the system to the earth to complete the circuit.^[14] The soil acts as a conductive medium due to its ionic content, particularly influenced by moisture and mineral composition, enabling the current to spread radially from the electrodes toward the source grounding point.^[15] To prevent interference with the grounded utility grid, SWER systems employ isolating transformers at the point of connection, which provide galvanic isolation between the multi-phase supply (typically 11-33 kV) and the single-phase SWER line (often 12.7 kV or 19.1 kV).^[13] These transformers ensure that no neutral is shared with the grid, thereby avoiding circulating earth currents that could arise from potential differences and compromise system stability or safety.^[14] Effective operation requires low earth resistance to minimize losses and ensure adequate current return, typically targeting 1-2 Ω at the isolating transformer and 5-10 Ω at distribution transformers.^[13] This is achieved using deep earth electrodes, such as driven rods or boreholes extending 3-5 m or more into the ground, often backfilled with conductive materials like bentonite to enhance contact with the soil and reduce impedance.^[14] The earth resistance R_{\text{earth}} varies significantly with soil type—ranging from low values in clay (10-100 Ω·m) to higher in sand (100-1000 Ω·m)—necessitating site-specific design.^[15] Voltage regulation in SWER lines is challenging due to the combined impedance of the conductor and earth path, leading to drops that can affect load performance over long distances.^[13] The approximate voltage drop can be expressed as:

\Delta V = I \times (R_{\text{line}} + R_{\text{earth}})

where I is the load current, R_{\text{line}} is the resistance of the single wire, and R_{\text{earth}} accounts for the variable earth path resistance influenced by soil conditions.^[15] In extended lines, capacitive coupling between the conductor and earth introduces charging currents, exacerbating the Ferranti effect where receiving-end voltage rises above sending-end levels under light loads.^[13] To mitigate these issues, load balancing across multiple SWER spurs—often derived from a three-phase source—is essential to minimize unbalanced earth return currents and maintain system efficiency.^[14]

Mechanical Design

The mechanical design of single-wire earth return (SWER) systems emphasizes robust, cost-effective components suited to remote and harsh rural environments, prioritizing longevity and minimal maintenance. Conductors typically consist of galvanized steel wires, valued for their high tensile strength that supports spans up to 400 meters, reducing the overall number of support structures required.^[16] In modern installations, aluminum-clad steel conductors are often employed to balance enhanced electrical conductivity with mechanical durability, particularly in longer or higher-load lines.^[17] Insulators in SWER infrastructure are selected for their ability to handle medium voltages (typically 11–33 kV) while resisting environmental degradation from moisture, UV exposure, and temperature extremes. Porcelain insulators, known for their rigidity and arc resistance, are commonly used in pin or post configurations on overhead lines.^[18] Polymer (composite) insulators offer advantages in weight reduction and flexibility, making them suitable for areas prone to mechanical stress, with both types engineered to maintain insulation integrity over decades in rural settings.^[19] Support poles are predominantly made of reinforced concrete to withstand corrosion, termite damage, and seismic activity common in rural terrains, with designs allowing for spans of 300–500 meters to minimize infrastructure density at approximately 2–3 poles per kilometer.^[20] This spacing optimizes material use while ensuring stability under typical wind loads up to 40 m/s. Wooden poles may be used in less demanding areas but are less prevalent due to shorter lifespans. Grounding at transformer sites relies on multiple deep-driven earth rods, typically 3–5 meters in length and 16 mm in diameter, made of copper-plated steel and arranged in a triangular configuration to achieve low earth resistance (under 5 ohms).^[8] These rods are driven at intervals around the transformer base to facilitate reliable current return through the soil, with additional horizontal copper conductors connecting them for uniform potential distribution. Design adaptations address local environmental challenges, such as elevating insulators by 1–2 meters above standard heights in flood-prone regions to prevent submersion and short-circuiting. In wind- and bushfire-vulnerable zones, structures incorporate reinforced concrete bases and guy wires for added stability, while conductors may include vibration dampers to mitigate aeolian effects.^[8] These modifications enhance resilience without significantly increasing costs, aligning with SWER's emphasis on economical rural deployment.

Performance Characteristics

Safety Considerations

One primary safety concern in single-wire earth return (SWER) systems is ground potential rise (GPR) during fault conditions, where fault currents flowing through the earth can create hazardous voltage gradients on the ground surface.^[9] To mitigate this, earth electrodes at transformer sites and line ends must achieve a low resistance, typically 5-10 ohms, to limit touch and step voltages to below 50 V, preventing electric shock to personnel or livestock.^[9]^[21] Protection against faults and overvoltages relies on specialized devices tailored to SWER's single-phase design. Automatic circuit reclosers detect and interrupt earth faults or short circuits, often reclosing briefly to distinguish transient issues from persistent ones, thereby isolating problems within seconds to minimize exposure time.^[22] Surge arrestors installed at transformers and key points divert lightning-induced surges, protecting insulation and reducing the risk of conductor failure.^[23] Earth fault detectors, including rapid earth fault current limiters, enhance sensitivity to low-level imbalances in the earth return path, enabling quicker isolation than standard overcurrent relays.^[24] In fire-prone regions, SWER lines pose a bushfire ignition risk from fallen conductors contacting dry vegetation, exacerbated by high winds or aging infrastructure. During Australia's 2009 Black Saturday bushfires, a fatigued SWER conductor on the Kilmore East line broke and arced for 3.6 seconds after recloser operation, igniting grass that led to a fire killing 119 people; similar failures contributed to the Coleraine and Horsham fires.^[25] Human safety protocols emphasize access controls and signage around high-risk areas. Warning signs must be posted near earth electrodes and transformer sites to alert the public of potential step and touch potentials, while restricted access zones prevent unauthorized entry within 10-20 meters of grounding points.^[9] Designs comply with IEC 60479-1 standards, which limit permissible touch voltages to 50 V AC for durations over 0.5 seconds to avoid ventricular fibrillation.^[26] Environmentally, SWER systems produce minimal electromagnetic interference due to the earth return path's natural screening, but stray currents from unbalanced loads can induce low-level electrolytic corrosion in nearby buried metallic pipes or structures.^[27] Mitigation involves maintaining balanced loads and using insulating joints in pipelines to interrupt stray current paths.^[27]

Economic Advantages

Single-wire earth return (SWER) systems offer substantial capital cost reductions compared to conventional distribution lines, typically achieving approximately 50% of the costs of an equivalent two-wire single-phase line.^[1]^[28] This savings stems primarily from the use of only one overhead conductor instead of two, halving the amount of copper or aluminum required, and the need for about 60% fewer poles—around 2.5 poles per kilometer versus 7 for standard lines—due to longer spans enabled by the design.^[1] Material and installation savings further enhance economic viability, with simplified insulators and pole-top fittings reducing overall setup expenses by 40-60% relative to three-phase systems in rural settings.^[8] For instance, SWER requires minimal hardware like crossarms and protection devices, allowing construction by less specialized labor and over varied terrain, with reported line costs as low as $5,344 per kilometer in low-density applications compared to $15,400 per kilometer for three-phase equivalents.^[8] These factors make SWER capital costs around 30-40% of three-phase systems, particularly beneficial for sparse rural networks.^[1]^[8] Operational efficiencies contribute to long-term financial benefits, including maintenance costs roughly 50% lower than conventional lines due to fewer components and reduced exposure to faults.^[1] In low-density rural areas, these savings often yield payback periods under 5 years for loads below 100 kVA, as seen in Australian deployments where SWER supports isolating transformers up to 200 kVA and distribution units of 25 kVA.^[1]^[21] Comparative metrics highlight SWER's edge, with significantly lower delivery costs per kVA compared to three-phase alternatives in optimized rural setups, enabling economical supply over distances exceeding 100 kilometers.^[28]^[8]

Reliability and Maintenance

Single-wire earth return (SWER) systems exhibit high reliability due to their inherent simplicity, featuring a single overhead conductor with earth return, which minimizes the number of components prone to failure compared to multi-wire distribution networks. This design reduces potential fault locations, such as joints and connections, contributing to lower overall outage rates in rural settings where SWER is predominantly deployed.^[29]^[30] Common failure modes in SWER systems include insulator breakage from mechanical stress or environmental factors, vegetation contact leading to short circuits, and corrosion of earth electrodes in areas with high soil resistivity or acidic conditions. Vegetation encroachment, particularly in dry or overgrown rural areas, accounts for a significant portion of faults, often resulting in arcing and potential fire ignition. Earth electrode corrosion can degrade grounding effectiveness, increasing fault currents and touch voltages. In Victoria, Australia, SWER powerlines are implicated in 30-40 annual fires, exacerbated during high-risk periods like total fire ban days when ignition probability rises 10-20 times.^[24]^[24]^[9] As of late 2024, Victoria's SWER networks achieved 100% coverage with high-speed protection devices through the SWER Automatic Circuit Recloser (ACR) program, further reducing fire risks.^[24] Maintenance practices for SWER emphasize preventive measures to sustain reliability, including annual visual inspections of lines, insulators, and transformers to detect wear or damage early. Earth electrode resistance must be tested regularly using methods like the Wenner four-electrode technique, with limits typically set at 5 ohms or less at distribution transformers to ensure safe fault clearing and limit touch voltages to 40 volts. Vegetation clearing is conducted every 2-3 years along rights-of-way to prevent contact faults, often guided by aerial surveys in remote areas. These routines contribute to the system's low upkeep demands, with designs allowing remote monitoring and firmware updates to minimize on-site interventions.^[9]^[9]^[24] Outage statistics for SWER reflect its linear or radial topology, where a single-point failure—such as a downed conductor or faulty transformer—can cause extended blackouts affecting all downstream customers, with average incident durations around 1-2 hours for repairs in accessible areas. Mitigation strategies include installing sectionalizers and reclosers to isolate faults and restore partial service quickly, reducing overall system average interruption duration index (SAIDI). Safety devices like surge arresters further enhance reliability by diverting lightning-induced surges.^[30]^[31] In harsh conditions, SWER demonstrates resilience to lightning strikes when equipped with proper surge arresters at transformers and line ends, which clamp overvoltages and prevent insulation breakdown. However, remote installations remain vulnerable to animal-related damage, such as impacts from wildlife on poles or conductors in ungrazed areas, necessitating reinforced designs or fencing in high-risk zones.^[32]

Upgrade and Expansion Options

One effective method to enhance existing SWER networks involves voltage upgrades, typically increasing the operating voltage from the standard 12.7 kV to 19.1 kV or 22 kV, which can extend the effective reach of the line by approximately 2-3 times due to reduced current and associated resistive losses.^[34] These upgrades necessitate the replacement or reconfiguration of isolating transformers at the substation and customer ends to handle the higher voltage while maintaining isolation from ground.^[32] In Australian contexts, such as Queensland's remote networks operated by Ergon Energy, voltage enhancements have been implemented to support growing loads without full infrastructure overhauls.^[32] Adding parallel conductors represents another upgrade pathway, converting the single-wire configuration to a two-wire return system while preserving the earth as a backup path, thereby boosting capacity to up to 500 kVA per line.^[32] This approach doubles the current-carrying capability compared to the original single-wire setup, allowing for greater power delivery to dispersed rural loads without extensive new construction.^[32] Utilities in Australia, including those in outback regions, have adopted this method to address capacity constraints on lines spanning hundreds of kilometers.^[32] Integration of renewable energy sources, such as solar photovoltaic arrays and wind turbines, into SWER networks has gained traction post-2010, particularly in remote Australian grids, through the use of grid-tied inverters that synchronize with the single-phase supply.^[35] For instance, in South Australian rural installations beyond Ceduna, hybrid systems combining 12 kW solar inverters with battery storage have been connected via Selectronic SP PRO units, effectively augmenting the limited 5 kW export capacity of SWER lines and providing surge support up to 12 kW for equipment like welders.^[35] These integrations reduce daytime loading on the earth return path, mitigate voltage drops, and enable larger renewable installations without immediate line reinforcements.^[35] Hybrid expansions that incorporate three-phase spurs into existing SWER lines offer a scalable solution for accommodating growing loads in targeted areas, such as agricultural or community hubs, while minimizing service disruptions.^[34] In Victoria's Powercor network, for example, a proposed upgrade of 606 km of 12.7 kV SWER lines across 44 systems to 22 kV three-phase configurations is planned, which would benefit 1,310 customers by adding short three-phase extensions for high-demand spurs without replacing the entire radial feeder.^[36] This phased approach allows seamless transition, with the original SWER serving as a fallback during construction.^[36] From a cost-benefit perspective, these upgrade options typically represent 20-30% of the expense associated with constructing entirely new distribution lines, while delivering up to a 50% increase in overall network capacity through combined voltage and conductor enhancements.^[32] In the Powercor initiative, the $63.1 million investment over 2026-2031 for SWER-to-three-phase conversions would add 4,800 kVA of capacity at an average cost far below greenfield developments, supporting economic growth in regional Victoria with minimal annual bill impacts of about $3 per customer.^[34]^[36]

Limitations and Power Quality Issues

One significant limitation of single-wire earth return (SWER) systems is the substantial voltage drop experienced over long transmission lines, primarily due to the high reactance of the earth return path. This reactance arises from the inductive and resistive components of the soil, leading to drops of up to 10-15% under typical operating conditions, which can impair voltage regulation and affect end-user equipment performance.^[13] The voltage drop can be approximated by the formula

V_{\text{drop}} = I \cdot X_{\text{line}} \cdot \sin(\theta),

where I is the load current, X_{\text{line}} is the line reactance, and \theta is the phase angle between current and voltage; this equation highlights how reactive power demands exacerbate the issue in extended rural networks.^[37] In steady-state analysis, such drops can reach 9.4% (0.094 per unit) in base-case scenarios without mitigation, limiting effective power delivery over distances exceeding 50 km.^[13] Power quality in SWER systems is further compromised by harmonic distortion, particularly from unbalanced loads that introduce triplen harmonics (multiples of the third harmonic), which propagate through the earth return and distort waveforms. These imbalances, common in rural settings with sporadic single-phase loads, can elevate total harmonic distortion levels, while capacitive charging currents along the line contribute to overvoltages via the Ferranti effect, potentially exceeding 10% above nominal voltage at light loads.^[38] Such issues degrade equipment lifespan and require careful load balancing to keep distortion below 5%.^[13] The performance of SWER heavily depends on soil conductivity, with poor results in rocky or dry areas where high resistivity (often >1000 Ω·m) increases I²R losses in the earth path, potentially causing up to 20% efficiency reductions compared to low-resistivity soils (<400 Ω·m). In such terrains, the earth return resistance can rise significantly due to low moisture and salt content, amplifying overall system losses and necessitating deeper grounding electrodes.^[13] Capacity is also constrained, rendering SWER unsuitable for loads exceeding 300 kVA or applications involving large inductive motors without additional compensation, as the isolating transformer's rating typically caps at 300 kVA and voltage instability worsens under high reactive demands.^[8] Mitigation strategies include the experimental deployment of series capacitors to compensate for line reactance and reduce voltage drops, though adoption remains limited due to cost and complexity; low-voltage switched capacitors have shown promise in field trials by improving voltage support and releasing network capacity in Queensland's SWER grids. Load management techniques, such as scheduling inductive loads to avoid peak imbalances, help maintain harmonic distortion under 5% and enhance overall stability without widespread infrastructure changes.^[39]

Applications and Uses

Rural Electrification in Developed Countries

Single-wire earth return (SWER) systems have played a key role in rural electrification across developed countries, particularly where low population densities and vast distances make conventional three-phase distribution uneconomical. In Australia and New Zealand, SWER is widely used to supply power to outback farming communities and remote rural areas, leveraging its cost-effectiveness for sparse loads. Australia alone features over 200,000 km of SWER lines, enabling reliable electricity access in arid and isolated regions.^[28] Ergon Energy, a major utility in Queensland, manages approximately 65,000 km of these networks, supporting agricultural operations and small communities across expansive territories.^[40] In New Zealand, SWER remains a staple for rural supply, originating from early 20th-century innovations tailored to the country's dispersed settlements.^[41] In the United States, SWER deployment is limited primarily to Alaska's remote villages, where harsh terrain and isolation necessitate specialized solutions. European adoption is rare due to denser infrastructure. Modern adaptations enhance SWER's viability in these settings, such as integrating smart grid technologies for real-time monitoring and fault detection. In New Zealand, the OtagoNet system—spanning approximately 1,000 km—incorporates smart meters and reclosers to improve reliability and power quality on SWER lines, allowing utilities like PowerNet to proactively manage outages in rural networks.^[42]^[31] These implementations have been driven by policy frameworks emphasizing universal access, including government subsidies and incentives for rural grid extension. In Australia and New Zealand, such measures facilitated near-complete electrification, reaching 99% coverage in targeted rural areas by the 2000s through state-funded programs that prioritized affordable technologies like SWER.^[43]^[44] SWER's general cost advantages, often 50-70% lower than traditional lines for low-demand scenarios, aligned well with these goals.^[11]

Use in Developing Nations

In Africa, SWER systems have played a key role in rural electrification efforts, particularly in Mozambique through the World Bank-supported ProEnergia project, which promotes the use of single-wire earth return and shield wire schemes to extend power from major sources like the [Cahora Bassa](/page/Cahora Bassa) hydroelectric dam to remote, low-load areas.^[45] In Uganda, pilot projects and studies during the 2010s have explored SWER for grid extensions and mini-grids, aiming to lower the overall costs of bringing electricity to dispersed rural populations by minimizing material and installation expenses in low-density regions.^[46] These initiatives leverage SWER's economic advantages, such as reduced conductor requirements, to make electrification feasible in areas where conventional three-phase lines would be prohibitively expensive.^[47] In Asia, SWER has been implemented in remote village networks, notably in Laos through successive World Bank-funded rural electrification programs post-2010, which have incorporated single-wire earth return systems to connect isolated communities efficiently.^[48] Similar applications in Thailand's rural areas have utilized SWER for low-cost distribution to underserved villages, supporting broader access in topographically challenging terrains.^[8] These projects demonstrate SWER's scalability in poverty contexts, where budget constraints prioritize affordable technologies over high-capacity infrastructure. Recent developments from 2012 to 2020 include studies in Uganda and India evaluating SWER-based mini-grids for standalone rural supply, highlighting potential cost savings of up to 70% compared to traditional overhead lines through simplified designs and earth return utilization.^[49] To address operational challenges, programs in these nations have emphasized community training for SWER maintenance, equipping local technicians with skills for routine inspections and fault repairs to enhance system longevity in resource-limited settings.^[50] Additionally, integration with off-grid solar hybrids has been tested, combining SWER distribution with photovoltaic inputs to improve reliability and reduce dependence on distant grid sources in hybrid mini-grid configurations.^[51]

Specific Installations and Case Studies

One notable implementation of single-wire earth return (SWER) systems in New Zealand is operated by PowerNet Limited in the South Island, where reclosers have been deployed along rural SWER lines to enhance reliability. Installed starting in the early 2000s, these electronic reclosers replaced older hydraulic models, enabling faster fault detection and isolation, which reduced momentary outages for rural customers by up to 50% in some feeders. This upgrade has maintained high uptime for thousands of remote users, demonstrating SWER's adaptability to modern protection technologies in challenging terrains.^[31] In Australia, Ergon Energy manages one of the world's largest SWER networks, spanning over 65,000 km across rural and remote Queensland, including extensions serving mining and agricultural loads. A key case involves the integration of battery energy storage systems (BESS) on outback SWER lines to address voltage fluctuations, where a 1 MWh BESS coupled with an advanced algorithm stabilized voltages within regulatory limits for loads up to 100 kVA, preventing blackouts during peak demand. This 2018 pilot project highlighted SWER's role in supporting isolated industrial applications, with the system operating at 22 kV and extending service to previously unelectrified areas.^[32]^[52] A pioneering prototype SWER installation occurred in Alaska, United States, connecting the city of Bethel to the village of Napakiak in 1980. This 8.5-mile (13.7 km), 14.4 kV single-phase AC line, constructed at a cost of $280,000, demonstrated the feasibility of SWER for Arctic rural electrification by linking a diesel plant to remote loads, initially providing reliable power to approximately 200 residents. However, around 2010, the line was upgraded due to structural deterioration, excessive line losses exceeding 10%, poor reliability from conductor failures, and escalating maintenance costs, leading to its replacement with a conventional three-phase AC system budgeted at $2.8 million.^[7]^[53] In Mozambique, SWER holds significant potential for rural electrification from major sources like the Cahora Bassa hydropower plant, though specific large-scale spurs remain limited; a conceptual case study proposes 100-200 km extensions at 11-22 kV to connect 30-50 villages, delivering 100-300 kVA capacities via earth-return paths to overcome grid extension costs in low-density areas. Post-2000 efforts have integrated similar low-cost distribution in Tete Province, electrifying dispersed communities and supporting small agro-processing loads, with initial pilots achieving 20-30% access gains in targeted zones.^[54] Across these installations, key lessons include the efficacy of shunt capacitors for voltage regulation in Australian SWER networks, where strategic placement along feeders has reduced voltage drops by 5-10% under varying loads, improving power quality without full line reconductoring. Essential Energy's implementations, for instance, used switched capacitor banks rated at 50-150 kVAR to counteract inductive effects, maintaining end-of-line voltages above 90% of nominal and extending asset life in long rural spans.^[55]

Applications in HVDC Systems

In high-voltage direct current (HVDC) transmission, single-wire earth return principles are adapted for monopolar configurations, where the return path utilizes the earth or sea instead of a dedicated metallic conductor, thereby reducing infrastructure costs for long-distance or submarine links. This approach is particularly suited to asymmetric loads or emergency operations in bipolar systems, allowing continued power flow at reduced capacity when one pole fails. The DC current flows out through the overhead line or cable and returns via ground or sea electrodes connected to the converter stations, leveraging the earth's conductivity as the neutral path. The core principle involves strategically placed earth electrodes to facilitate low-resistance return while minimizing environmental impacts. Electrodes are typically designed as deep-buried rings, linear arrays, or meshes, with materials like titanium for anodes to ensure durability against electrolytic degradation and silicon-chromium-iron alloys for cathodes. In monopolar setups, the anode and cathode electrodes are positioned at opposite ends of the transmission line, often separated by hundreds of kilometers to distribute current density and reduce localized voltage gradients that could exacerbate corrosion.^[56] For submarine applications, sea water's higher conductivity enables shallower electrode placements, further simplifying design.^[57] This adaptation offers significant economic advantages in HVDC systems, primarily by eliminating the need for a parallel return conductor, which can account for a substantial portion of total line costs in remote or underwater installations. Earth return also lowers transmission losses compared to metallic paths due to the earth's parallel resistance pathways, making it viable for high-power links over 100 km. Electrode designs incorporating titanium enhance longevity, with some installations demonstrating operational stability over decades without replacement.^[57] Notable examples include the Baltic Cable, commissioned in 1994, which spans 250 km submarine from Sweden to Germany at ±450 kV in monopolar mode with sea return via a titanium mesh anode (800 m²) in Sweden and copper cable cathode (5,620 m) in Germany, enabling 600 MW transfer while avoiding additional cabling costs. Similarly, the Pacific DC Intertie in the USA, operational since 1970, employs partial earth return in monopolar fallback mode across 1,360 km at ±500 kV, using a ring electrode (3.2 km circumference with 1,067 anodes) at the Celilo station and a linear array of 24 silicon-iron rods at Sylmar, supporting up to 3,100 MW with earth as the neutral during single-pole operation. Proposed Asian supergrids, such as the GOBITEC initiative, incorporate HVDC links with potential monopolar earth return elements for interconnecting renewable sources across vast distances, though many designs favor metallic returns for environmental compliance.^[58] Despite these benefits, electrolytic corrosion poses a key limitation, as the unidirectional DC current can accelerate degradation of nearby buried pipelines, structures, or electrode components through electrochemical reactions.^[56] Mitigation strategies include periodic polarity reversal to neutralize ion migration, installation of metallic return paths as backups, and site selection ensuring electrodes are at least 30 km from sensitive infrastructure to limit interference. Continuous monitoring of soil resistivity and current distribution is essential to maintain system integrity and comply with environmental regulations.

References

[1]
What is Single Wire Earth Return (SWER)? | Wilken Pty Ltd
SWER is fundamentally different from conventional power distribution systems in that it uses only a single conductor to supply single-phase electric power.
[2]
An analysis of single wire earth return (SWER) system for rural ...
The primary objective of this investigation was to determine the general applicability of Single Phase Earth Return(SWER) system for rural electrification.
[3]
Mandeno, Lloyd | Dictionary of New Zealand Biography | Te Ara
His involvement with electric-power generation began in 1910–11 with the installation of the first alternating-current plant in Auckland, a 6,600-volt link ...Missing: Sparge SWER
[4]
Lloyd Mandeno (1888–1973) | Engineering NZ
While he was in Tauranga, Mandeno devised and patented the single-wire earth-return (SWER) system of electrical reticulation which is now in use in many parts ...Missing: Sparge invention
[5]
Single Wire Earth Return Distribution Grids: A Panacea for Rapid ...
The Single Wire Earth Return (SWER) system was developed in the 1920s to provide a low-cost means of electricity distribution to sparsely populated rural ...Missing: electrical | Show results with:electrical
[6]
Single Wire Earth Return Distribution Grids: A Panacea for Rapid Rural Power Penetration in Africa via Regulatory Policy Transfer
**Summary of https://ieeexplore.ieee.org/document/8928822:**
[7]
[PDF] Distributing Alaska's Power: - Denali Commission
5.1.4.3 Single Wire Earth Return (SWER). Single wire earth return (SWER), also referred to single wire ground return (SWGR), is a technology that was ...
[8]
[PDF] Low Cost Grid Electrification Technologies - WAME
The Single Wire Earth Return (SWER) system is basically a single phase distribution system at MV using the earth as the return conductor. There are two basic ...
[9]
None
### Summary of Single Wire Earth Return (SWER) Application Guide
[10]
ELECTRIC TELEGRAPH HISTORY & CONSTRUCTION
Over long distances, only 1 wire was used on the telegraph poles with the ground return to complete the circuit being actual earth ground. Although the ...
[11]
US645576A - System of transmission of electrical energy.
NIKOLA TESLA, OF NE\V YORK, N. Y.. SYSTEM OF TRANSMISSION OF ELECTRICAL ENERGY;. SPECIFICATION forming part of Letters Patent No. 645,576, dated March 20, 1900.
[12]
Rural Single Wire Earth Return distribution networks
Single Wire Earth Return (SWER) systems are used for supplying electricity at low cost, where electricity supply is required for small populations of people ...
[13]
http://www.diva-portal.org/smash/get/diva2:574879/fulltext01.pdf
[14]
[PDF] Planning Models for Single Wire Earth Return Power ... - DiVA portal
Dec 10, 2012 · In Single Wire Earth Return. (SWER) power distribution networks, the earth itself forms the current return path of the single phase system ...
[15]
[PDF] Feasibility of Remote Earth Monitoring for SWER Systems
Single Wire Earth Return (SWER) is an example of engineering brilliance which is elegant in its simplicity. The design involves one high voltage conductor with ...
[16]
(PDF) Power flow in distribution networks with earth return
Aug 10, 2025 · ... paper proposes Single Wire Earth Return (SWER) electrification scheme. This is because SWER's installation costs are about one third of ...
[17]
[PDF] Overhead Conductor Condition Monitoring
Dec 12, 2018 · High-strength and extra-high-strength galvanised steel conductors are commonly used on. Single Wire Earth Return (SWER) lines in distribution ...
[18]
United Energy in Australia Takes Action to Minimize Bushfire Risk
May 18, 2022 · ... wire earth return (SWER) overhead lines. The latter are ... aluminum clad steel conductor with a cross-sectional area of 25 mm2(0.038 ...
[19]
[PDF] Section 5: SWER system installed - practical considerations - piesa
SWER protection - SWER. “recloser” with fused “by pass”. Page 13. Protection ... Comparison between typical 22 and 33 kV line post insulators (porcelain).
[20]
Polymer Strain Insulators at Summit Power
SWER Constructions · Railway Crossing · Concrete Pole Constructions · Low Voltage ... Polymer Strain Insulators, also referred to as polymer long rod insulators ...
[21]
[PDF] Overhead Design Manual - Ausgrid
Oct 7, 2020 · Reinforced concrete poles shall have a maximum total ... 10.3 Intercircuit spacing. 10.3.1 Clearance to interspan pole. Minimum ...
[22]
[PDF] Single Wire Earth Return (SWER)
Single Earth Wire Return (SWER). 3. SWER System. • Line to ground voltages typically 12.7kV or. 19.1kV. Page 4. Single Earth Wire Return (SWER). 4. SWER - ...
[23]
Recloser Fundamentals | NOJA Power
Single Phase Reclosers are used on Single Wire Earth Return networks, or alternatively as a protection method for laterals in a North American style ...Missing: arrestors | Show results with:arrestors
[24]
fundamentals of surge arresters - Eaton
A surge arrester is a protective device for limiting voltage on equipment by discharging or bypassing surge current.
[25]
[PDF] FireSafe SWER EFD Trial Final report - Energy
Jun 18, 2022 · SWER: Single Wire Earth Return – a powerline technology that uses a single high-voltage wire to carry current to remote customers, the current ...
[26]
2009 VBRC - Final Report - Vol 2 - Electricity-Caused Fire
The SWER and 22-kilovolt distribution networks constitute a high risk for bushfire ignition, along with other risks posed by the ageing of parts of the ...
[27]
https://www.corrosionpedia.com/stray-current-corrosion-and-preventive-measures/2/1623
[28]
Stray Current Corrosion and Preventive Measures - Corrosionpedia
Aug 18, 2017 · Stray current can cause serious damage if left unchecked. However, there are methods for detecting and combating it.Missing: single | Show results with:single
[29]
SWER still going strong - Energy Source & Distribution
May 18, 2014 · Presently, Australia operates a total of about 200,000km of SWER lines, at 19.1kV and 12.7kV. New South Wales and the ACT operate about 30,000 ...Missing: century | Show results with:century
[30]
[PDF] SWER (Single Wire Earth Return) systems User applications
The introduction of SWER (Single Wire Earth Return) technology has significant merits regarding cost effectiveness to supply electricity to remote areas.
[31]
Single Wire Earth Return (SWER) system for Rural Electrification
TECHNICAL OVERVIEW The Single Wire Earth Return (SWER) system is a unique method of power distribution used primarily for rural electrification.
[32]
New Generation of SWER-Line Reclosers Reduces Outages for ...
Mar 22, 2022 · PowerNet decided TripSaver II reclosers were a better option than hydraulic reclosers to reduce outages along SWER lines for its New Zealand customers.Missing: km | Show results with:km
[33]
[PDF] S&C Improves Power Quality in Australia's Outback
the use of maintenance-intensive refrigeration-based cooling systems. Twin Grid Utility Support System units providing extra support along a SWER line.
[34]
Power lines on rural properties - WorkSafe
Sep 4, 2017 · Another incident resulted when a single wire ('Single Wire Earth Return' or SWER) line dropped to within 1.5 metres of the ground when a fault ...Missing: damage outage
[35]
None
Summary of each segment:
[36]
How To Reinforce Skinny Rural SWER Connections With Solar ...
Apr 4, 2024 · Reinforcing a SWER supply using a battery hybrid system to stiffen up what's already available will be the most economical.
[37]
Rural power upgrade to deliver benefits for the bush - Powercor
Feb 24, 2025 · “Upgrading the SWER network in targeted areas will support regional businesses grow and invest in larger facilities and operations, driving ...Missing: earth return strategies
[38]
A Look into Steady State and Transient Performance of Power Lines Integrating Single Wire Earth Return Circuits
**Summary of Steady State Performance, Voltage Drop, Reactance, and Power Quality in SWER Lines:**
[39]
A Heuristic Model for Planning of Single Wire Earth Return Power ...
... Single Wire Earth Return (SWER) networks into the planning of such systems ... loads are highly unbalanced or have considerable triplen harmonic current content.
[40]
Deployment of low voltage switched capacitors on single wire earth ...
Ergon Energy operates over 64,000 kilometres of Single Wire Earth Return (SWER) networks to supply electricity in rural and remote regions of Queensland.
[41]
Single Wire Earth Return (SWER) | Engineering NZ
It is also present in remote areas of Australia where more than 150,000 kilometres of SWER lines are in service.Missing: expansion | Show results with:expansion
[42]
[PDF] OtagoNet Joint Venture (OJV) - PowerNet
OtagoNet Joint Venture (OJV). OJV, through SmartCo, are working with Meter Equipment Provider. (MEP) to retrieve smart meter data to develop and improve ...
[43]
Access to electricity (% of population) - Australia | Data
Access to electricity, urban (% of urban population) · Access to electricity, rural (% of rural population) · Electricity production from oil sources (% of total).Missing: 99%
[44]
Australia Electricity Access | Historical Chart & Data - Macrotrends
Australia's electricity access was 100% in 2023, 2022, 2021, and 2020, with no increase from 2022 to 2023.
[45]
[PDF] MOZAMBIQUE ENERGY FOR ALL (ProEnergia) PROJECT
Mar 7, 2019 · This technique promotes the use of single-wire earth return (SWER) and shield wire schemes when the load and the geographic conditions are ...
[46]
[PDF] THE USE OF SINGLE WIRE EARTH RETURN (SWER) AS A ...
Single wire earth return systems are to be supplied from double-wounded transformers (isolating transformers). These circuits are to supply only double- wound ...Missing: principle | Show results with:principle
[47]
[PDF] THE USE OF SINGLE WIRE EARTH RETURN (SWER) AS A ...
SWER requires an under-strung earth wire for safety reasons whenever the line comes close to a village, children play-grounds, sport facilities, trading ...
[48]
[PDF] Lao PDR - Documents & Reports - World Bank
Single Wire Earth Return (SWER) network reticulation, pioneered and widely ... Several more SWER projects are planned for implementation in the near term.
[49]
[PDF] MINIGRIDS IN THE MONEY - RMI
Our analysis has identified one pathway by which minigrid costs can be reduced by 60%. This cost reduction would rapidly accelerate market growth for minigrids ...
[50]
[PDF] Impact Assessment of Rural Electrification | Norad
Oct 8, 2013 · • Applying Single wire earth return (SWER). Because this technique involves the stringing of only one wire, the construction techniques are ...
[51]
[PDF] Five government approaches to promote solar hybrid mini grids in ...
The bottom line. Different private sector-led and government-led approaches to the development of solar hybrid mini grids are found around the world.Missing: SWER | Show results with:SWER
[52]
[PDF] Development of advanced SWER models for the Ergon Energy ...
Ergon Energy has over 65 000 km of Single Wire Earth Return (SWER) networks operating within rural and remote localities of Queensland, Australia. SWER ...
[53]
[PDF] Small-Scale High Voltage Direct Current - Stanford
Single-Wire Earth. Return (SWER). A system by which the earth is used as the return portion of a circuit. Single-Wire Ground. Return (SWGR). Synonymous with “ ...
[54]
Potential for Increased Rural Electrification Rate in Sub-Saharan ...
Aug 7, 2025 · Therefore, this paper undertakes a review of a single wire earth return (SWER) network as a RER improvement solution. The paper undertakes ...
[55]
Economics of upgrading swer distribution systems - ResearchGate
In the Australian setting, voltage regulation is becoming the determining factor for older SWER systems. In long systems, directly connected shunt reactors ...
[56]
[PDF] HVDC Power Transmission Electrode Siting and Design
Unbalanced currents associated with the New. Zealand hybrid HVDC arrangement have caused earth currents that caused interference with underground facilities; ...<|separator|>
[57]
None
### Summary of SwePol and Baltic Cable HVDC Systems (Monopolar Earth/Sea Return)
[58]
[PDF] GOBITEC AND ASIAN SUPER GRID FOR RENEWABLE ENERGIES ...
Because of the extensive electricity transport distances in the ASG project, the use of HVDC transmission lines is strongly recommended. High voltage direct ...