Curtiss Model F
The Curtiss Model F was a pioneering family of biplane flying boats developed by the Curtiss Aeroplane and Motor Company in the United States, first flown in 1912 and remaining in service until 1927 as a versatile trainer and patrol aircraft for early naval aviation.[1] Introduced amid rapid advancements in seaplane technology, the Model F evolved from the earlier Model E design, incorporating a distinctive "step" hull that improved hydrodynamic performance for water takeoffs and landings.[2] Powered initially by a 75-horsepower Curtiss O engine in its two-seat pusher configuration, it achieved speeds of up to 55 miles per hour, while later variants upgraded to a 100-horsepower Curtiss OXX-3 engine, boosting performance to 70 miles per hour with an endurance of about 5.5 hours.[1] Over 300 units were produced, of which approximately 150 were for U.S. military use and the remainder exported or for civilian applications, serving not only the U.S. Navy and Army but also the militaries of Great Britain, Brazil, Italy, and Russia, as well as civilian operators in countries including New Zealand, marking it as one of the most widely adopted early flying boats.[3][4][5] The Model F played a crucial role in military aviation milestones, including the first installation of a gyroscopic autopilot in August 1913 on the C-2 variant, the debut of U.S. military heavier-than-air craft in combat during April 1914 aboard the USS Birmingham, and the inaugural catapult launch from a warship in November 1915 using the AB-2 from the USS North Carolina.[1] During World War I, it became the U.S. Navy's standard primary trainer following the American entry into the conflict in 1917, with the Coast Guard also employing it to train its inaugural aviators after aviation duties were authorized by Congress in 1916; pilots like Second Lieutenant Norman B. Hall and Third Lieutenant Elmer F. Stone conducted coastal assessments along Virginia and North Carolina using these aircraft.[6][3] Variants of the Model F included specialized configurations such as stretcher-equipped models for medical evacuation, five-seat passenger versions, and even triplane adaptations, alongside nicknames like "Flying Fish," "Freak Boat," "Tadpole," and "Seagull" that reflected its amphibious quirkiness.[1] By 1918, it was gradually supplanted by improved designs like the Curtiss MF, but its contributions to refining flying boat hulls—transitioning from flat-bottomed to V-shaped for better efficiency—laid essential groundwork for subsequent seaplane developments in the interwar period.[6][2]Background and Development
Origins and Initial Design
The Curtiss Model F originated as an evolution from the earlier Model E hydroaeroplane, which featured a biplane configuration mounted on separate floats for water operations. In late 1911 and early 1912, Glenn Curtiss and his team at the Curtiss Aeroplane and Motor Company in Hammondsport, New York, shifted the design toward a true flying boat by integrating a full hull as the fuselage, eliminating the need for external floats and improving hydrodynamic efficiency for water takeoffs and landings.[7][4] This transition addressed limitations in stability and planing observed during hydroaeroplane trials, drawing on Curtiss's prior experience with seaplanes like the 1911 Triad (A-1).[8] The core design of the initial Model F prototypes adopted a biplane layout with unequal-span wings—the upper wing longer than the lower for better lift distribution—and a pusher propeller configuration to keep the propeller clear of water spray. Powered by a single water-cooled Curtiss OX engine rated at 75 to 100 horsepower, the aircraft featured an open cockpit accommodating two crew members side by side, a wooden hull constructed from cedar planks for buoyancy and strength, and fabric-covered wings braced by interplane struts. This setup emphasized simplicity and versatility for early aviation applications, with the hull's flat-bottomed forward section aiding in water handling.[1][4] The first prototype achieved its maiden flight on January 12, 1912, piloted by Glenn Curtiss himself over the frozen waters near Hammondsport, New York. Initial testing focused on water operations, including taxiing, planing, and stability during low-speed maneuvers on Keuka Lake, where the aircraft demonstrated reliable takeoff and landing capabilities despite the rudimentary hull shape. These trials validated the flying boat concept's practicality, with Curtiss logging several short flights to refine control responses and structural integrity under varying wind conditions. Following initial tests in Hammondsport, further development and water trials were conducted in San Diego, California, in 1912.[9][10][1] Hull shaping was a collaborative effort, with Glenn Curtiss overseeing overall design and Henry Kleckler, a skilled boatbuilder and Curtiss foreman, contributing to the planing surface refinements, such as testing a stepped underside to reduce water resistance during acceleration.[3][10]Production Evolution and Improvements
Production of the Curtiss Model F began on a small scale in 1912, with the U.S. Navy ordering four initial units (designated C-2 through C-5, later redesignated AB-2 through AB-5) for evaluation as flying boat trainers.[11] By 1916, eight additional aircraft had been delivered, but wartime demands following U.S. entry into World War I in 1917 prompted significant expansion, leading to an order for 144 Model F trainers that year.[11] This scaling reflected the aircraft's selection as the Navy's standard trainer in April 1917, enabling mass production to meet the urgent need for pilot instruction amid global conflict.[11] Key design improvements enhanced the Model F's performance and reliability during this period. In 1913, the introduction of the 100 hp Curtiss OXX-3 V-8 water-cooled engine replaced earlier powerplants, providing greater thrust for improved speed and endurance, with the aircraft achieving up to 69 mph and 5.5 hours of flight time.[12] Subsequent modifications included revised wing bracing with unequal-span biplane configuration and ailerons integrated into the upper wing trailing edge by 1918 in the Model MF variant, which boosted lift and handling stability.[11] Aluminum engine cowlings were also adopted to reduce weight, contributing to overall efficiency without compromising structural integrity.[12] Manufacturing processes at the Curtiss Aeroplane and Motor Company's Buffalo, New York, factory emphasized hand-built construction, with wooden fuselages crafted from varnished lumber and fabric surfaces doped for tautness and weather resistance. To address corrosion challenges in saltwater environments, these materials were treated with protective varnishes and dopes, ensuring durability for naval operations.[13] Subcontracting supported scaling, and licensed assembly of 80 Model MF flying boats at the Naval Aircraft Factory by 1918, bringing total output to 22 MF units from Curtiss plus these, for a combined F/MF production exceeding 246 airframes.[11] Military adaptations incorporated bomb racks capable of carrying up to 230-pound ordnance and mounts for Lewis machine guns, transforming the trainer into a versatile patrol platform.[13] These production efforts had substantial economic ramifications, with wartime contracts valued at over $6 million awarded to Curtiss Aeroplane and Motor Company, fueling its expansion into one of the largest aviation suppliers globally by 1918 and including exports to nations like Russia and Italy.[14] Overall, more than 300 units were produced across variants, incorporating these iterative enhancements to support Allied war efforts.[11]Operational History
US Navy Adoption and Training
The U.S. Navy began integrating the Curtiss Model F into its aviation program in 1912, procuring the early flying boats for evaluation and operational testing at the Naval Aviation Camp in Annapolis, Maryland. These initial aircraft, designated as hydroaeroplanes AH-19 through AH-22, were employed to assess the potential of seaplanes for naval scouting and reconnaissance, marking a pivotal step in the development of shipboard aviation capabilities.[6] A key milestone in the Navy's adoption occurred with the establishment of the first permanent naval air station at Pensacola, Florida, in 1914, which served as the primary hub for seaplane training. The Model F's pusher configuration, with the propeller mounted behind the crew, facilitated safe water landings and takeoffs, making it ideal for instructing pilots in maritime operations. By 1916, the aircraft had become the Navy's standard trainer, with programs at Pensacola and other sites qualifying dozens of aviators in seaplane handling and navigation.[15][16][17] The U.S. Coast Guard also adopted the Model F following congressional authorization of aviation duties in 1916, using it to train its first aviators. Pilots such as Second Lieutenant Norman B. Hall and Third Lieutenant Elmer F. Stone conducted coastal assessments along Virginia and North Carolina.[6] Foundational experiments with the Model F advanced naval aviation integration, including the first catapult launch on April 26, 1915, from a stationary coal barge in Pensacola Bay by Lieutenant Patrick N. L. Bellinger in an AB-2 variant. This was followed by the historic first underway shipboard catapult launch on November 5, 1915, from the armored cruiser USS North Carolina, executed by Lieutenant Commander Henry C. Mustin in another AB-2 Model F. These tests demonstrated the aircraft's viability for battleship-based scouting, enabling rapid deployment from capital ships without relying on calm waters.[18] Procurement of the Model F expanded rapidly amid pre-war preparations, with eight additional units acquired by 1916 to support growing training needs. Under wartime mobilization in 1917, orders escalated to approximately 144 aircraft, bolstering the formation of specialized Naval Air Detachments for coastal patrol and instruction. This surge transformed the Model F into the backbone of early Navy aviation expansion.[3] Operational logistics presented challenges, particularly saltwater corrosion on the wooden hulls and fabric coverings, as well as reliability issues with the Curtiss OX-5 engine in humid marine environments. These factors necessitated regular depot-level overhauls at facilities like the Naval Aircraft Factory in Philadelphia, where aircraft underwent disassembly, treatment, and reassembly to maintain airworthiness.[19]Combat Roles and International Use
The Curtiss Model F entered combat service on April 24, 1914, during the U.S. occupation of Veracruz, Mexico, when Lieutenant (junior grade Patrick N. L. Bellinger piloted the AB-3 variant on the first U.S. Navy heavier-than-air reconnaissance mission over the harbor to scout Mexican positions.[20] This flight marked the initial combat use of an American military aircraft, providing critical intelligence on enemy troop movements amid challenging conditions including high winds and limited visibility.[21] Following the U.S. entry into World War I in 1917, Model F flying boats conducted anti-submarine patrols along the East Coast, escorting convoys and spotting submerged threats for coordination with surface vessels while leveraging their range for extended maritime surveillance.[22] These operations, often launched from stations like Rockaway Naval Air Station, contributed to coastal defense efforts against German U-boats, though the aircraft's modest speed and payload limited direct engagements.[19] Internationally, the Imperial Russian Navy acquired batches of Model F flying boats in 1913–1914, deploying them for reconnaissance and patrol duties in the Baltic and Black Seas as part of early wartime naval aviation operations.[23] The Italian Navy ordered three customized Model Fs in 1913, which entered service for Adriatic Sea patrols upon Italy's 1915 entry into the war, supporting anti-submarine and scouting missions from battleships like the Dante Alighieri.[24] Similarly, the Ottoman Empire purchased one Model F in 1914 following demonstrations in Istanbul, employing it for reconnaissance over coastal waters during the initial phases of World War I.[25] A significant milestone in the Model F's military application occurred on August 30, 1913, when Lawrence Sperry demonstrated the world's first autopilot-assisted flight using a C-2 variant equipped with Elmer Sperry's gyroscopic stabilizer system, enabling hands-off control during a flight over Long Island Sound.[1] This innovation, tested under U.S. Navy observation, foreshadowed automated navigation aids for future patrol and combat roles.[26]Civilian and Commercial Applications
Following World War I, numerous Curtiss Model F variants, particularly the MF trainer, entered the civilian market as surplus aircraft, with new units priced at around $1,750 compared to their original $7,500 cost.[24] The postwar civil version, known as the Seagull or Model 18, featured modifications including two additional seats for a total capacity of up to four passengers in an enclosed cabin, enabling conversions for passenger transport and other commercial roles.[12] Approximately 16 Seagulls were produced and sold to private owners and operators, capitalizing on the anticipated boom in civil seaplane usage along waterways and coastal areas.[12] Commercial operations highlighted the Seagull's versatility in early airline services, with Rogers Airlines maintaining a fleet of ten aircraft for mail and passenger routes primarily between Miami, Florida, and Nassau, Bahamas, during winter months from the early 1920s until at least 1927.[11] In summer, these aircraft relocated to upstate New York for maintenance and to support secondary revenue through barnstorming exhibitions.[1] Curtiss Flying Service and similar organizations utilized the type for specialized tasks, including aerial surveys and photography along coastal regions, leveraging the flying boat's ability to operate from water bases inaccessible to wheeled aircraft.[27] Beyond scheduled services, the Model F found widespread use in exploratory and entertainment roles during the 1920s, including barnstorming tours where pilots offered joyrides and demonstrations at airshows and seaside resorts.[27] These operations often involved short passenger hops from beaches at amusement parks, providing affordable public access to flight and promoting aviation enthusiasm; Rogers Airlines' summer activities exemplified this, combining repairs with exhibition flights to sustain operations.[1] Safety concerns and economic factors limited the type's longevity in civilian hands, with incidents such as the May 4, 1921, crash of a Canadian-registered MF Seagull (G-CADL) highlighting vulnerabilities like loss of control in turbulent conditions, contributing to a phase-out by the mid-1920s as more robust designs emerged.[28] Operating costs, while low due to surplus availability, averaged around general early seaplane expenses of the era, but structural fatigue from prolonged saltwater exposure and high utilization in commercial flights accelerated retirements.[27] The Model F's civilian applications influenced early U.S. seaplane oversight, informing the Department of Commerce's 1926 Air Commerce Act regulations on aircraft certification and water operations through demonstrated needs for buoyancy and hull integrity standards.[29]Variants
Standard Military Variants
The baseline Model F, produced from 1912 to 1917, served as the foundational military flying boat with a 90 hp Curtiss OX-2 pusher engine, a length of 27 feet 9.75 inches, and a wing area of 387 square feet.[30] It was employed primarily for pilot training and initial reconnaissance duties by the U.S. Navy, with its simple biplane structure and interchangeable float/landing gear setup enabling versatile amphibious operations. Early versions with 75-90 hp engines achieved about 60 mph, while the 1917 configuration with a 100 hp OXX-3 reached 69 mph.[30] The Model MF, an evolution introduced in 1918, incorporated a 100 hp Curtiss OXX-6 engine, single-bay wing bracing for improved aerodynamics and approximately 10% greater lift efficiency over the baseline, and expanded fuel tanks supporting up to 5.5 hours of endurance.[31] A total of 102 units were constructed for naval service, achieving a top speed of 76.5 mph at sea level and a cruising speed of 68 mph, which enhanced its suitability for patrol and scouting roles.[31] Across these standard military models, performance progressed notably—early Model F versions reached about 60 mph, the 1917 Model F 69 mph, while the MF improved to 76.5 mph—yet all retained modular hull designs with interchangeable floats or wheels for seamless transitions between water and land bases.[30][31]Custom and Experimental Variants
The Seagull, a civil version of the Model MF introduced after 1918, accommodated up to four seats and was sold for commercial applications, with approximately 16 units produced. Later designated Model 25, it featured the MF's improved wings and was popular for passenger and utility roles.[32][12] The Reid Hydroaeroplane, emerged as a bespoke modification of the Model F in 1913, commissioned for Glenn Curtiss's associate Marshall Reid, equipped with tricycle landing gear and a 75 hp Curtiss V-8 pusher engine for enhanced ground handling. This single aircraft participated in exhibition flights, demonstrating the versatility of customized hydroaeroplane configurations.[33] The Judson Triplane, built in late 1916 or early 1917, was an experimental triplane reconfiguration of the Model F, powered by a 150 hp Curtiss V-X engine to evaluate aerodynamic stability in multi-wing designs. Only one such conversion was built.[34] In 1913, the Italian Navy acquired at least three Model F flying boats equipped with 100 hp engines for reconnaissance duties.[24] Testing outcomes from a 1913 Model F prototype included pioneering autopilot integration trials, where the aircraft, designated C-2, achieved the first automatic flight on August 30 using Elmer Sperry's gyroscopic stabilizer, paving the way for advanced control systems in aviation.[1]Operators
Military Operators
The United States Navy was the largest operator of the Curtiss Model F, procuring the type from 1912 onward as its standard primary training flying boat under designations C-2 through C-5 (later reclassified AB-2 through AB-5). Over 144 units were acquired following U.S. entry into World War I in April 1917, in addition to earlier purchases including 15 ordered in autumn 1916, for a total of approximately 170 aircraft in the Model F family; these served primarily for pilot training at stations in Pensacola, Florida, and Hampton Roads, Virginia, as well as coastal patrols and experimental roles such as ambulance conversions with stretcher fittings, before retirement by 1922.[35][30] The United States Army used the 1913 Model F for training purposes in early aviation experiments.[30] The Royal Navy of Great Britain received limited numbers of Model F aircraft, with some operated by constructors like White and Thompson for evaluation and coastal roles.[11] The Imperial Russian Navy acquired an unspecified number of Model F aircraft through two direct purchase batches in 1913–1914, including six initial units in early 1914 and a second batch delivered in March 1914 with modified double-concave hulls; these standard variants were employed for reconnaissance duties with the Baltic Fleet until operational losses during the 1917 Revolution.[4] The Italian Regia Marina purchased three custom Model F units in 1913, tailored with unique hull specifications for warship compatibility, and subsequently license-built eight more through the Zari company at Bovisio; the aircraft supported anti-submarine patrols in the Adriatic Sea from battleships like the Dante Alighieri and cruisers such as Amalfi and San Marco, with two lost in combat by 1916.[24][30] The Ottoman Navy imported one Model F aircraft in 1914 via neutral export following demonstrations in Istanbul, assigning it to the newly formed flying service at Yeşilköy for Black Sea patrols during World War I; it was captured by Russian forces in 1915.[25] A precursor organization to the Royal New Zealand Air Force obtained one Model F in 1917 for coastal defense operations, which saw limited service before postwar scrapping.[1] The Brazilian Navy acquired seven Model F units through direct purchases—three in 1916 and four in 1918—plus one license-built example at the Navy Aviation School; these supported riverine patrols along the Amazon, with the last operational flight recorded in 1925.[30] Aircraft were generally obtained via direct commercial purchases from the Curtiss Aeroplane and Motor Company or precursors to wartime aid programs like Lend-Lease, alongside neutral exports and limited license production for select operators.[4]Civilian Operators
Following the demobilization of military forces after World War I, surplus Curtiss Model F flying boats entered the civilian market, where they were acquired by private companies and individuals for commercial aviation activities.[3] In the United States, Rogers Airlines operated ten surplus Model MF variants from 1920 until at least 1927, primarily for passenger transport and mail delivery between Miami and Nassau, with summer operations in New York for barnstorming and repairs.[1] Curtiss Flying Service, the civilian subsidiary of the Curtiss Aeroplane and Motor Company, maintained a fleet of Model F aircraft in the 1920s for tasks including aerial surveying and barnstorming exhibitions, with primary bases in Buffalo, New York, and Miami, Florida.[36] In Canada, surplus Model F flying boats were used for timber scouting operations over the forests of British Columbia in the early 1920s.[37] Surplus Model F aircraft were registered to individual owners in the United States for exhibition flights and promotional tours in the early 1920s.[3] Regulatory oversight by precursors to the Federal Aviation Administration, including inspections by the U.S. Department of Commerce's Aeronautics Branch, ultimately led to the grounding of unmodified Model F hulls by 1925 due to metal fatigue and safety concerns identified in routine airworthiness checks.[38]Preservation and Legacy
Surviving Aircraft
Few original Curtiss Model F airframes survive today, with at least four major authenticated examples documented through historical records and aviation authorities. These include complete or substantially restored aircraft and significant components, verified by serial numbers, construction logs, and FAA certification processes for airworthy restorations. Prior to 2018, no original Model F airframes were considered airworthy due to deterioration over a century of exposure.[39][37][40] The most prominent survivor is serial number 112, a 1914 Model F that crashed in Connecticut in 1915. Surviving parts from this aircraft, including structural elements, were incorporated into a comprehensive restoration by Century Aviation in Wenatchee, Washington, beginning in late 2016. The project utilized original blueprints, period photographs, and authentic materials such as spruce for the hull to recreate the biplane flying boat configuration. The restored aircraft achieved its first post-restoration flight on August 21, 2018, at Moses Lake, Washington, during events associated with EAA AirVenture Oshkosh. It is on display at the American Heritage Museum in Hudson, Massachusetts, maintained as the sole airworthy example of its kind.[39][40][3] A complete airframe of the 1918 Model MF variant, known as the Seagull and registered as NC903 (formerly U.S. Navy A-611), is preserved on static display at the Omaka Aviation Heritage Centre in Blenheim, New Zealand. This example features an intact hull, wings, and original Curtiss OX-5 V-8 engine, retaining much of its period configuration from post-World War I civilian service. Its authenticity is confirmed by construction number records and exhibition documentation.[37] Another surviving example is a 1920s Curtiss MF Seagull (Model 18), originally named "Eleanor III" and used in the 1924-25 South American expedition by Dr. Alexander Hamilton-Rice. Restored in 1974, this original airframe was donated to the Science Museum in London after the expedition and later acquired by the Canada Aviation and Space Museum in 1968. As of 2023, it was transferred to the Montreal Aviation Museum due to space constraints at its previous location.[37] Preservation of these artifacts faces ongoing challenges typical of wood-and-fabric aircraft from the era, including vulnerability to wood rot from moisture exposure and degradation of doped fabric coverings. Climate-controlled storage and periodic conservation treatments are essential to prevent further deterioration, as evidenced in restoration efforts that addressed corrosion and structural weakening.[40]Replicas and Modern Restorations
In the postwar era, efforts to recreate the Curtiss Model F have focused on preserving its pioneering flying boat design for educational and demonstrative purposes. The Glenn H. Curtiss Museum in Hammondsport, New York, houses a full-scale replica of a 1914 Model F flying boat, constructed using historical blueprints and materials faithful to the original specifications. Completed in 2007, this static display aircraft incorporates elements of early biplane pusher configurations and was briefly flyable, with its last recorded flight occurring over Keuka Lake in 2018 during a seaplane event.[41][42] A significant modern restoration project was undertaken by Century Aviation in Wenatchee, Washington, beginning in late 2016. This effort revived a 1914 Model F using approximately original proportions, with the hull rebuilt from spruce and mahogany based on period blueprints and photographs, supplemented by recovered components from a historical example. Powered by a restored Curtiss OX-5 engine, the aircraft achieved its first flight in over a century on August 21, 2018, at Moses Lake, marking it as the world's only confirmed flyable Model F as of that date; modern safety enhancements, such as reinforced structural elements, were integrated to ensure airworthiness without altering core design features.[39][40][43] These projects highlight the Model F's enduring appeal in aviation heritage, with replicas and restorations primarily serving museum displays and occasional demonstrations rather than routine operations. As of 2025, no additional flyable examples beyond the Century Aviation restoration have been documented, emphasizing the rarity of active recreations.[37]Specifications
Model F (1917)
The Curtiss Model F, introduced in 1917 as a standard production model for the U.S. Navy, served primarily as a training and reconnaissance flying boat. This two-bay biplane featured a wooden hull and fabric-covered wings, with a pusher propeller configuration that positioned the engine above and behind the wing for better visibility and splash protection during water operations. It supported a crew of two—a pilot and an observer—and included provisions for an ambulance configuration carrying one stretcher patient.[44][45] Key specifications for the Model F emphasized reliability for coastal patrols and short-range missions, with an empty weight of 1,860 lb (844 kg) and a gross weight of 2,460 lb (1,116 kg). The aircraft measured 27 ft 9¾ in (8.47 m) in length, with a wingspan of 45 ft 1⅜ in (13.75 m), height of 11 ft 2⅞ in (3.42 m), and wing area of 387 sq ft (36 m²). Fuel capacity was 50 US gal (189 L), supplemented by 6 US gal (23 L) of oil, enabling operational endurance suited to its roles.[45][30][](Peter M. Bowers, Curtiss Aircraft 1907–1947 (London: Putnam, 1979), p. 132)| Category | Specification |
|---|---|
| Powerplant | 1 × Curtiss OXX-3 V-8 water-cooled inline engine, 100 hp (75 kW), pusher configuration[45][30] |
| Performance | Maximum speed: 69 mph (111 km/h) at sea level Cruise speed: 55 mph (89 km/h) Range: 320 mi (515 km) Endurance: 5 hr 30 min Service ceiling: 4,500 ft (1,372 m) Rate of climb: 300 ft/min (1.5 m/s)[](Peter M. Bowers, Curtiss Aircraft 1907–1947 (London: Putnam, 1979), p. 132)[24] |
| Armament | Provision for 1 × 0.30 in (7.62 mm) Lewis machine gun for the observer and up to 100 lb (45 kg) of bombs; typical loadout for reconnaissance missions[46][](Peter M. Bowers, Curtiss Aircraft 1907–1947 (London: Putnam, 1979), p. 133) |
Model MF (1918)
The Curtiss Model MF, developed in 1918 as a modified variant of the earlier Model F, incorporated structural enhancements such as a revised single-bay biplane wing configuration and added sponsons for improved seaworthiness and stability on water operations.[47] These upgrades addressed limitations in the baseline Model F, enabling better handling during training and patrol missions while maintaining the flying boat's core pusher biplane layout.[48] Designed primarily as a naval trainer with potential for light patrol duties, the MF accommodated a crew of two—typically an instructor and student—though configurations allowed for an additional radio operator, supporting up to three personnel for extended operations.[47] Empty weight stood at 1,850 lb, with a gross weight of 2,488 lb, reflecting increased capacity over the lighter predecessor.[47]| Category | Specification |
|---|---|
| Dimensions | Length: 28 ft 10 in Wingspan: 49 ft 9 in Height: 11 ft 7 in Wing area: 400 sq ft |
| Powerplant | 1 × 100 hp Curtiss OXX-6 V-8 (improved cooling); optional 150 hp Hisso A in select examples |
| Performance | Maximum speed: 72 mph Cruise speed: 60 mph Range: 345–400 mi Endurance: 6 hr Service ceiling: 4,100–5,000 ft Rate of climb: 300–350 ft/min |
| Armament | 2 × 0.30 in Lewis machine guns (one dorsal, one ventral) 200 lb bomb load |
| Fuel & Oil | 65 US gal fuel; 8 US gal oil |