Fact-checked by Grok 2 weeks ago

LA-2A Leveling Amplifier

The LA-2A Leveling Amplifier is a legendary tube-driven electro-optical compressor, originally developed by Teletronix Engineering Company in 1962, renowned for delivering smooth, program-dependent gain reduction with a warm, natural sound that enhances vocals, bass, and other sources without introducing harsh artifacts.^[1]^[2] Invented by electrical engineer Jim Lawrence, the device evolved from his earlier LA-1 model, which he created in the late 1950s to address manual gain-riding challenges in radio broadcasting, drawing on his experience with optical sensors from the Titan Missile Program at NASA's Jet Propulsion Laboratory.^[1] The LA-2A's core innovation lies in its T4 optical attenuator—a custom electroluminescent panel paired with cadmium-sulfide photocells—that modulates audio gain via light intensity, providing an attack time of approximately 10 milliseconds and a multi-stage release from 0.06 seconds for 50% recovery to 0.5–5 seconds for full release, resulting in transparent compression up to 40 dB.^[1]^[3] This design, combined with a single-stage tube amplifier offering 40 dB of gain, simple controls (Peak Reduction and Gain knobs), and a VU meter for monitoring, made it exceptionally user-friendly and versatile for both compression and limiting modes.^[3]^[4] Produced until 1969 after Teletronix's acquisition by Babcock Electronics in 1965 and subsequent integration into UREI, the LA-2A saw limited reissues in the 1970s and 1980s before Universal Audio faithfully resurrected it in 1999 using original 1960s specifications, including hand-built T4 cells, cementing its status as a studio staple.^[1] Its enduring significance stems from its ability to impart musical warmth and texture, earning induction into the TECnology Hall of Fame in 2004 and widespread use on hit recordings across genres, from classic rock to modern hip-hop, often praised for taming dynamics on vocals while preserving their emotional character.^[2]^[4] Technical specifications include a frequency response of +0/-1 dB from 30 Hz to 15 kHz, input/output impedances selectable at 50, 150, 250, or 600 ohms, and low distortion under 0.5% THD at ±10 dBm, ensuring high-fidelity performance in professional audio environments.^[3]

History

Development

The LA-2A Leveling Amplifier was invented by James F. Lawrence II, an electrical engineer who founded Teletronix Engineering Company in Pasadena, California, in 1958. Lawrence developed the device to address the need for reliable automatic gain control in broadcast and recording applications, building on his earlier work with optical attenuation technology.^[1]^[5] The LA-2A evolved from Teletronix's prior models, the LA-1 and LA-2. The single-channel LA-1, introduced in 1958 with only about 100 units produced, gained early acclaim when one unit was acquired by singer Gene Autry, who used it extensively for his radio broadcasts and recording sessions.^[1] The subsequent LA-2, a dual-channel version, was adopted by major broadcasters, including CBS, which purchased a pair shortly after its introduction, and RCA, which deployed units in its New York and Nashville facilities for signal limiting.^[1] A key innovation in the LA-2A was the incorporation of the T4 electro-optical cell, which utilized a luminescent panel to drive paired photo resistors, enabling smooth, program-dependent compression. This design overcame the limitations of earlier vacuum tube compressors, such as inconsistent gain reduction and abrupt response characteristics, by providing a more transparent and musical dynamic control. In 1962, Lawrence refined the LA-2 into the first LA-2A prototype, featuring a gray faceplate and improved internal layout for reduced noise.^[1]^[5] Initial testing and refinement of the LA-2A involved field trials in professional radio stations, where feedback from broadcasters like those at CBS and RCA helped optimize its performance for real-world audio leveling tasks. These iterations focused on enhancing stability and usability prior to wider adoption.^[1]

Production and Acquisitions

The Teletronix LA-2A Leveling Amplifier entered production in 1962, with manufacturing handled by the Teletronix Engineering Company until the unit's discontinuation in 1969.^[4] Approximately 1,800 units were produced during this period, based on serial number ranges from 001 to 1800.^[4] Early models, known as Gray Face variants, featured a battleship gray faceplate and were built from 1962 to 1965, encompassing serial numbers 001 to 572 with turret board construction for reduced noise.^[4] In 1965, Teletronix was sold to Babcock Electronics, which continued production briefly before the company's broadcast division—including the LA-2A patents and designs—was acquired by United Recording Electronics Industries (UREI) in 1967.^[1]^[4] Following the acquisition by Babcock Electronics in 1965, the LA-2A shifted to Silver Face variants starting that year, characterized by a brushed aluminum faceplate and minor circuit revisions across models 2A, 2B, and 2C, with production totaling around 1,228 units (serial numbers 573 to 1800) until the line ended in 1969 amid the industry's transition to solid-state technology.^[1]^[4] The original run's limited output contributed to the unit's rarity and enduring value in professional audio circles.^[4]

Design

Circuitry and Components

The LA-2A Leveling Amplifier employs a tube-based design centered around a single gain stage that provides up to 40 dB of amplification while integrating compression functionality.^[1] It utilizes two 12AX7A dual-triode vacuum tubes for voltage amplification in the side-chain and output circuits, a 12BH7A dual-triode as a cathode follower in the output stage to maintain low distortion and wide bandwidth, and a 6AQ5 beam power tube to drive the electroluminescent panel in the compression element.^[6] These tubes operate on high-voltage supplies derived from the unit's power transformer, contributing to the device's warm sonic character and dynamic response.^[7] At the heart of the LA-2A's compression mechanism is the T4 electro-optical cell, a passive attenuator comprising an electroluminescent panel as the light source and two cadmium-sulfide photocells as light-dependent resistors.^[1] One photocell modulates gain reduction by varying its resistance in response to light intensity—decreasing resistance as the panel brightens to attenuate the signal—while the second drives the VU meter for visual feedback in gain reduction mode.^[7] The T4 cell's design ensures program-dependent attack and release times without electronic timing circuits, relying instead on the optical interaction for smooth, natural compression.^[6] The signal path begins with an input transformer for isolation and impedance matching, followed by a portion of the signal feeding directly into the gain reduction circuit via one of the 12AX7A tubes.^[7] This drives the 6AQ5 tube, which modulates the electroluminescent panel in the T4 cell to control attenuation before the compressed signal passes through the output amplifier stage—comprising the other 12AX7A and the 12BH7A—and exits via an output transformer for balanced connection.^[6] There is no active side-chain detector; compression is achieved by the audio signal itself illuminating the panel, creating a simple architecture that minimizes phase issues through its optical design.^[1] The power supply operates on 115 V AC (configurable to 230 V), drawing approximately 35 watts at 50/60 Hz, with the high-voltage B+ for the tubes generated from the internal power transformer and filtered for stable operation.^[8] Hand-wired turret boards connect the components, reducing noise and enhancing reliability in this all-analog design.^[1]

Controls and Operation

The LA-2A Leveling Amplifier features a minimalist front panel designed for straightforward user interaction, with only two primary knobs and a mode switch to facilitate precise control over dynamic range processing. The Peak Reduction knob adjusts the compression threshold and amount by varying the drive to the optical attenuator, allowing users to dial in subtle leveling or aggressive reduction as needed for the input signal. The Gain knob provides makeup gain at the output stage to compensate for the applied reduction, restoring the desired overall level without introducing additional complexity. A Limit/Compress switch on the lower chassis selects between Limit mode, which employs a higher ratio for rapid peak taming, and Compress mode, suited for gentler, program-dependent compression on sustained material.^[8]^[6] Metering is handled by a single VU meter that serves dual functions, switched between gain reduction display (calibrated from -10 to 0 dB) and output level monitoring with positions calibrated to +4 dBm and +10 dBm at 0 VU via an adjacent Meter selector switch. This setup enables real-time observation of the compressor's effect, with the gain reduction scale directly indicating the amount of attenuation applied by the T4 optical cell. The meter's zero point can be fine-tuned using a small screwdriver-adjustable potentiometer for accuracy during setup.^[8]^[6] To operate the LA-2A, route the input signal through the balanced XLR connectors, then set the Peak Reduction knob while monitoring the VU meter in gain reduction mode to achieve the target compression—typically starting low and increasing until 3-6 dB of reduction on peaks for natural results. Next, switch the meter to output mode and adjust the Gain knob to match the original signal level or unity gain, ensuring transparent processing. Finally, select Limit or Compress mode based on the audio source, such as Limit for percussive transients or Compress for vocals and instruments. This optical design inherently simplifies operation by forgoing explicit ratio or threshold controls, relying instead on the T4 cell's automatic response for intuitive, ears-guided adjustments.^[8]^[6]^[1]

Technical Specifications

Performance Characteristics

The LA-2A Leveling Amplifier features an attack time of approximately 10 milliseconds, which allows it to preserve natural transients in audio signals while effectively controlling peaks.^[9] Its release time is program-dependent, achieving 50% recovery in about 60 milliseconds and full release ranging from 0.5 to 5 seconds, depending on signal amplitude and content, contributing to the unit's smooth and musical compression behavior.^[9] The compressor can provide maximum gain reduction of up to 40 dB without introducing additional harmonic distortion, thanks to its electro-optical design.^[9] The compression ratio is set by the Compress/Limit switch: approximately 3:1 in Compress mode and infinity:1 in Limit mode, with program-dependent behavior due to the optical design and a soft-knee characteristic that ensures gradual onset of compression for transparent dynamic control.^[10]^[11] Input levels reach a maximum of +16 dBm, while output capability is +10 dBm nominal, supporting professional line-level signals in studio environments.^[9]^[12]

Frequency Response and Distortion

The LA-2A Leveling Amplifier maintains a flat frequency response of +0/-1 dB from 30 Hz to 15 kHz at unity gain, ensuring faithful reproduction of audio signals across the primary audible range.^[9] This specification, derived from its tube amplifier and optical attenuator design, supports transparent operation without significant tonal alteration in the passband.^[6] Under compression, the response exhibits only minor roll-off at the frequency extremes, preserving overall fidelity while the sidechain's frequency-dependent behavior influences gain reduction timing. The device's input and output transformers impose a practical bandwidth limitation of approximately 30 kHz, though the circuitry is optimized for the 20 Hz to 20 kHz audio spectrum relevant to recording applications.^[13] These transformers also contribute to effective rejection of hum and buzz through balanced operation, enhancing signal integrity in studio environments.^[6] Total harmonic distortion (THD) measures less than 0.5% at normal levels, with typical performance at 0.25% for outputs around ±10 dBm, reflecting the clean operation of the lag-free optical attenuator.^[9] During maximum gain reduction of up to 40 dB, THD rises minimally to under 0.75% at +16 dBm output, avoiding audible artifacts.^[14] The equivalent input noise floor stands at -70 dBm, delivering low-noise performance better than 70 dB below +10 dBm output, suitable for high-fidelity audio processing.^[9] The LA-2A's compression imparts a characteristic warmth through subtle even-order harmonics generated primarily by the tube output stage, particularly enhancing vocals with musical coloration.^[6] This harmonic behavior, combined with the T4 electro-optical cell's smooth response, distinguishes the unit's sonic signature without introducing harsh odd-order distortion.^[14]

Applications

Studio Recording Techniques

The LA-2A Leveling Amplifier is widely employed in studio recording for its optical compression, which provides smooth, transparent dynamic control across various sources. On vocals, it excels at leveling inconsistent performances while preserving natural timbre and adding subtle warmth, often inserted directly on the vocal channel to tame peaks without introducing harshness.^[10] For bass guitar, the LA-2A offers effective transient control, enhancing sustain and fattening the low-end tone through its tube makeup gain stage, making it a staple for both electric and upright bass tracking.^[6] In drum applications, it is commonly used on individual elements like kick or snare for punch preservation or on the drum bus to glue the kit together, leveraging its program-dependent release to maintain rhythmic energy.^[15] For mix bus processing, the LA-2A contributes overall cohesion and subtle harmonic enhancement, helping to polish the final stereo image without over-compressing the entire mix.^[15] In professional workflows, the LA-2A is typically inserted inline on individual channels via XLR or barrier strip connections in analog consoles, functioning as outboard gear to process signals post-preamp.^[6] For stereo applications, such as drum buses or full mixes, two units are linked using a short shielded cable (under 2 feet) connected to the sidechain terminals, ensuring balanced compression across left and right channels by synchronizing the T4 optical cells.^[6] This setup allows for precise control in analog desks, while in digital environments, it integrates seamlessly as hardware in hybrid systems or via plugin emulations on DAW tracks. Settings for the LA-2A emphasize its simple controls: the Peak Reduction knob sets the compression amount and threshold (from 0 to full clockwise for up to 40 dB of gain reduction), while the Gain knob provides up to +40 dB of makeup amplification.^[10] For light compression aimed at transparency—such as 2-4 dB of reduction on vocals or bass—the Peak Reduction is set moderately (around 3-5 on the dial), paired with the Compress mode (3:1 ratio) to handle full-range dynamics gently.^[16] Heavier settings, like 10+ dB reduction for limiting peaks on drums or mix bus, involve higher Peak Reduction values and the Limit mode (infinity:1 ratio), with the Emphasis control adjusted counter-clockwise to increase sensitivity to high frequencies if needed.^[15] These guidelines ensure the LA-2A's attack (approximately 10 ms) and release (0.06 seconds for 50%, extending to 1-15 seconds) respond naturally to program material.^[10] The LA-2A integrates effectively with complementary gear to enhance studio chains; it is often placed after a Pultec-style EQ for corrective shaping before compression or paired with tube preamps to amplify its inherent warmth in digital-hybrid setups, where the vacuum tube output stage adds harmonic richness to otherwise sterile signals.^[16] In such configurations, the compressor's tube circuitry (including 12AX7 and 12BH7 tubes) benefits digital recordings by imparting analog character during tracking or mixing.^[6] Maintenance of the LA-2A hardware requires attention to its vacuum tubes and T4 electro-optical cell, as these components affect performance over time. Tubes, such as the two 12AX7A preamp tubes, one 12BH7A driver tube, and one 6AQ5 output tube, should be inspected and replaced by an authorized service center if symptoms such as intermittent compression, distortion, lack of volume, or reduced output occur after extended use.^[17] The T4 cell, responsible for light-dependent gain reduction, can degrade due to age or heat exposure, leading to inconsistent compression; recalibration or replacement by qualified technicians is necessary to restore optical response, often involving no user-serviceable parts.^[6] Regular professional servicing ensures longevity in studio environments.^[17]

Notable Recordings

The LA-2A has been instrumental in shaping the sound of several landmark recordings, particularly for its ability to provide smooth, musical compression on vocals and other elements. On Nirvana's 1991 album Nevermind, producer Butch Vig used the LA-2A in conjunction with a Neumann U67 microphone to capture Kurt Cobain's vocals, running the signal directly to tape for dynamic control that preserved the raw intensity of the performances while taming peaks.^[18] This approach contributed to the album's signature grunge vocal tone, alternating between aggressive shouts and vulnerable whispers. Producer Glen Ballard employed the LA-2A for vocal compression on Alanis Morissette's 1995 breakthrough album Jagged Little Pill, praising its gentler and warmer character compared to more aggressive units like the Distressor.^[19]^[20] The compressor's optical design helped maintain the emotional delivery in tracks like "You Oughta Know," adding subtle glue without harsh artifacts. Engineer Mike Clink utilized the LA-2A on bass during the recording of Guns N' Roses' 1987 debut Appetite for Destruction, enhancing the low-end punch in songs such as "Welcome to the Jungle."^[21] For rock vocals, producer Joe Barresi has highlighted the LA-2A's effectiveness, noting that it works particularly well when seeking a natural, musical response on lead and backing parts.^[22] Barresi's endorsement underscores the unit's enduring appeal for hard rock productions, where it imparts warmth and cohesion without over-compressing the source.

Reissues and Emulations

Hardware Reissues

Universal Audio began reissuing the Teletronix LA-2A in 1999 as one of its first products following the company's relaunch, aiming to recreate the original unit's hand-wired circuitry and performance characteristics using period-correct components.^[1] The reissue employs custom-manufactured T4 electro-optical attenuator cells, meticulously engineered to replicate the proprietary design of the originals, along with a tube-driven gain reduction circuit for smooth, program-dependent compression.^[1] These units are hand-built in the USA, featuring the classic Silver Face aesthetic of later original models, and maintain the simple two-knob operation (Peak Reduction and Gain) that defined the LA-2A.^[3] Subsequent production runs in the 2010s and beyond incorporated refinements for enhanced reliability, including a modern internal power supply capable of 120/240V operation to meet contemporary electrical standards while preserving the original's sonic profile.^[3] Differences from the 1960s originals are minimal and primarily involve safety-compliant updates, such as compliant wiring and connectors, ensuring the reissue matches the vintage frequency response within 1 dB from 30 Hz to 15 kHz and distortion levels under 0.5% at +10 dBm.^[6] In the 2020s, boutique manufacturers like Warm Audio introduced variants such as the WA-2A, a high-voltage opto-compressor using CineMag transformers and Kenetek T4-style cells to approximate the LA-2A's warm, musical compression at a more accessible price point.^[23] Other notable reproductions include the Heritage Audio Successor ELA-2A (released around 2020), which clones the original ELA-2A predecessor with modern upgrades, and the Lindell Audio LA-2A (2010s), offering a budget-friendly rackmount version.^[24] All official Universal Audio reissues are housed in a standard 2U rackmount format (3.5 inches high), priced at approximately $6,000 as of 2025, and include individual calibration to factory specifications for consistent performance.^[25] Limited-edition variants, such as the dual-channel 2-LA-2 introduced alongside the initial reissues, offer stereo linking for mastering applications while retaining the core electro-optical design.^[26] Original 1960s LA-2A units remain highly collectible, often commanding $5,000 to $10,000 or higher on secondary markets due to their scarcity and historical significance in recording studios.

Software Emulations

Software emulations of the LA-2A Leveling Amplifier replicate the original hardware's electro-optical compression characteristics through digital modeling, allowing integration into digital audio workstations (DAWs) for modern music production. These plugins aim to capture the device's smooth, program-dependent response and tube warmth without requiring physical hardware.^[10] Universal Audio released the first UAD LA-2A plugin in 2001 as a DSP-based emulation for their UAD platforms, setting an early standard for analog modeling.^[1] In 2013, they updated it with the LA-2A Leveler Collection, featuring three versions—Gray, Silver, and Legacy—that model variations in the original circuitry, including differences in T4 optical cell aging and tube stages for distinct tonal responses. The Gray version emulates a late-1960s unit with mellowed characteristics, while the Silver represents an early unit with brighter highs, and the Legacy preserves the original 2001 algorithm.^[27]^[28]^[10] Waves introduced the CLA-2A in 2009 as part of the Chris Lord-Alge Signature Series, modeled after the engineer's personal vintage LA-2A units for a signature sound on vocals and instruments. It supports mono and stereo operation, includes a mix knob for parallel compression, and offers sidechain filtering options to emulate the hardware's natural compression while adding harmonic saturation.^[29]^[30] Other notable emulations include Avid's BF-2A, originally from Bomb Factory and rebranded under Avid around 2008, which provides classic tube compression warmth for vocals, guitars, and drums within Pro Tools. IK Multimedia's T-RackS White 2A, released in 2011, focuses on the all-tube design for gentle, fat compression on dynamic tracks, integrating into the T-RackS mastering suite. Native Instruments' VC 2A, launched in 2011 as part of the Vintage Compressors bundle developed with Softube, adds modern features like sidechain input, a low-cut filter, and mix blend control to the core electro-optical sound, suitable for vocals, bass, and pads.^[31]^[32]^[33] More recent emulations include Black Rooster Audio's VLA-2A (2020), which emphasizes variable-mu and optical hybrid modeling for versatile compression, and Overloud's GEM Comp LA (2022), offering multiple LA-2A variants with enhanced CPU efficiency.^[34]^[35] These emulations employ component-level modeling to simulate key elements of the LA-2A, such as the T4 optical cell's response, which provides program- and frequency-dependent behavior with a multi-stage release that can extend to 0.5 to 5 seconds for full recovery. Tube saturation is replicated to add harmonic distortion, while the optical attenuator ensures smooth, automatic attack and release times around 10 milliseconds and 60 milliseconds on average, respectively, maintaining the device's 3:1 compression ratio.^[10]^[15]^[9] In DAWs, native plugins like the Waves CLA-2A, IK Multimedia White 2A, and Native Instruments VC 2A operate with low latency directly on the host CPU, enabling real-time processing without additional hardware. In contrast, Universal Audio's UAD LA-2A requires a UAD accelerator card or interface for DSP processing to achieve similar performance.^[36]^[30]

References

[1]
A History of the Teletronix LA-2A Leveling Amplifier
Aug 14, 2025 · The LA-2A Leveling Amplifier has only a single gain stage and is one of the simplest compressors to operate with two knobs: Gain and Peak Reduction.
[2]
Why is the Teletronix LA-2A the world's most famous audio compressor?
### Summary of Teletronix LA-2A
[3]
Teletronix LA-2A Classic Leveling Amplifier
### Product Description
[4]
The Teletronix LA-2A Optical Compressor/Limiter - Vintage King
### Description
[5]
The History of the Optical Compressor — Vintage Pro Audio Equipment | AudioScape Engineering Co.
### Summary of LA-2A Development and T4 Electro-Optical Cell
[6]
2192 AND 2-1176 NOMINATED FOR 2004 TEC AWARDS, LA-2A INDUCTED INTO TECNOLOGY HALL OF FAME
- **LA-2A Induction**: Confirmed induction into the TECnology Hall of Fame in 2004.
[7]
[PDF] Model LA-2A Leveling Amplifier - Universal Audio
The input transformer provides isolation and impedance matching. After this the signal is fed into both the side-chain circuit and the gain reduction circuit.Missing: path | Show results with:path
[8]
[PDF] How the LA2A Leveling Amplifier does its magic - analogvibes
The signal coming from the T4 cell is directly going to the. „Gain Control“ pot. Depending on how much we turn up that knob, the signal is fed to the 12AX7 tube ...
[9]
None
### Summary of Front Panel Controls, Metering, and Operation Steps for Teletronix LA-2A Leveling Amplifier
[10]
Teletronix LA-2A Classic Leveling Amplifier - Universal Audio Support
Aug 15, 2025 · A History of the Teletronix LA-2A Leveling Amplifier. Features. True to the original in design, manufacturing and performance; Lag free, ...
[11]
Teletronix LA-2A Leveler Collection Manual
### Studio Techniques, Applications, and Settings for LA-2A
[12]
Are the LA-2A and 1176LN hard knee or soft knee compressors?
Apr 27, 2007 · The LA-2A is frequency dependent soft knee, and the 1176LN is hard knee at 20:1 ratio and “semi-soft” at other ratios.
[13]
https://www.sowter.co.uk/acatalog/VINTAGE-COMPRESSOR-TRANSFORMERS-J-to-Z.html
[14]
VINTAGE COMPRESSOR TRANSFORMERS J to Z - Sowter
1449 UA 175 / Teletronix LA-2A Original Input transformer (Replaces 1009) Drip Opto 4. 600 ohm to 50K input transformer ratio 1:9. 1 Bandwidth 5Hz to 30 kHz.
[15]
The Legendary Teletronix LA-2A Leveling Amplifier from 1962
The Teletronix LA-2A is a legendary analog compressor and leveling amplifier using optical compression, designed for smooth, transparent audio, and can ...
[16]
Tips & Tricks — Teletronix LA-2A Classic Leveler Plug-In Collection
### Summary of LA-2A Tips & Tricks
[17]
The producer's guide to the Teletronix LA-2A - MusicRadar
Mar 1, 2024 · Our in-depth guide to the classic compressor revered by gearheads and beloved for its warmth, colour and transparent sound
[18]
Replacing Tubes in Your UA Analog Hardware
Aug 14, 2025 · Replacing Tubes: LA-610 MkII Channel Strip. This unit requires one 12AX7 tube at locations V1 and V3, and one 12AT7 tube at locations V2 and V4.How Do I Replace The Tubes... · Testing Your Tubes · Replacing And Seating Tubes
[19]
BUTCVIG: Nevermind The Garbage
Utilising a Neumann U67 and an LA2A, most of Cobain's vocals were recorded in the small Studio B at Sound City and ran straight to tape. The results alternate ...
[20]
Studio Sessions | May 2–28, 1991 - Sound City ... - LiveNIRVANA.com
Artist. NIRVANA. Kurt Cobain (vocals, guitar); Krist Novoselic (bass); Dave Grohl ... For most of Cobain's vocals, Vig utilized a Neumann U67 and an LA2A ...
[21]
Glen Ballard
Teletronix LA2A compressor. "The Distressor is great for vocals, and we generally use that. The LA2A is a little gentler and warmer than the Distressor, but you ...
[22]
Classic Compressors
"I added the LA2A for warmth,” comments Serge Tsai, for example, echoing similar 'gentler and warmer' epithets from producer Glen Ballard. However, a few ...
[23]
[PDF] Model 2-LA-2 Twin T4 Leveling Amplifier - Universal Audio
The 2-LA-2 retains the same key gain reduction components and simple controls found in the LA-2A, but adds the modern convenience of a stereo-matched tool made ...<|control11|><|separator|>
[24]
https://vintageking.com/blog/modern-la2a-reproductions/
[25]
Universal Audio Teletronix LA-2A Classic Leveling Amplifier
$$4,999.00 In stock Rating 5.0 (10) The LA-2A is a legendary, tube-driven compressor for gain reduction, used on vocals, bass, drums, and more, with simple controls and vintage-spec circuitry.
[26]
Master list of release year? | UAD, Apollo, and LUNA Forums
Mar 3, 2023 · The original LA-2A and 1176 emulations were in 2002 as well, as were RealVerb Pro and Nigel. Here's an amusing review from the time. https:// ...UAD LA-2A now native and free for all until Oct 31stLA-2A Silver, Gray and LA-2: When do you reach for each?More results from uadforum.com
[27]
https://uadforum.com/community/index.php?threads/master-list-of-release-year.61643/
[28]
Waves releases CLA Classic Compressors - KVR Audio
Jul 22, 2009 · Like the mid-'60s classic, the CLA-2A sounds great on guitars and bass, and really shines on vocals, according to Waves. It's topped off with ...
[29]
CLA-2A Compressor Limiter Plugin - Waves Audio
The legendary electro-optical tube compressor · Modeled from Chris Lord-Alge's personal vintage hardware · Natural-sounding even with heavy compression · Optimum ...
[30]
having difficulty with BF-2A and MC77 after the 8.x upgrade
Jan 29, 2009 · Pro Tools 8 installs newer versions of some Bomb Factory plug-ins that may not work with your previous Bomb Factory "v4" iLok authorizations.
[31]
IK Multimedia releases T-RackS Black 76 and White 2A plug-ins and ...
Free deliveryIK Multimedia releases T-RackS Black 76 and White 2A plug-ins and updates T-RackS to v3.5 (incl. 64-bit for Win & Mac). 2nd June 2011 - KVR ...
[32]
Native Instruments VC 2A review | MusicRadar
Rating 4.0 Aug 22, 2011 · The VC 2A is one of three new vintage compressors from NI that feature DSP guts from modelling experts Softube - note that you can buy all three for €199.
[33]
https://www.musicradar.com/reviews/tech/native-instruments-vc-2a-490115
[34]
https://www.blackroosteraudio.com/en/products/vla2a/