Salinity is the concentration of dissolved inorganic salts in seawater, primarily sodium chloride along with other major ions in nearly constant proportions as established by Forchhammer's principle.[1] It is typically quantified in practical salinity units (PSU), a dimensionless scale based on conductivity measurements, where 1 PSU approximates 1 gram of salt per kilogram of seawater.[2] The global average ocean salinity stands at approximately 35 PSU, reflecting a balance of salt inputs from continental weathering and outputs via sedimentation and circulation.[3][4]Salinity profoundly affects seawaterdensity, which—interacting with temperature—drives thermohaline circulation, the global conveyor belt redistributing heat and influencing climate patterns from the equator to the poles.[5][6] Spatial variations arise from evaporation exceeding precipitation in subtropical regions (elevating salinity to over 37 PSU) and freshwater dilution in high latitudes or near river mouths (lowering it below 33 PSU), with the Atlantic Ocean exhibiting higher average salinity than the Pacific due to differential evaporation and circulation.[3][7] Temporal changes, including those from ice formation and melting, further modulate density gradients critical for deep-water formation in polar regions.[8] These dynamics underscore salinity's role in marine ecosystems, where it constrains osmotic tolerances of organisms, and in broader Earth system processes like the water cycle and carbon sequestration.[9]
Definitions and Fundamentals
Definition and Units of Measurement
Salinity is defined as the total mass of dissolved inorganic salts in a water sample, expressed relative to the mass of the solution, most commonly applied to seawater in oceanographic contexts.[7] In precise terms, it represents the grams of dissolved salts per kilogram of seawater, excluding minor organic components and accounting primarily for major ions such as sodium, chloride, magnesium, sulfate, calcium, and potassium./06:Temperature_Salinity_and_Density/6.01:Definition_of_Salinity) This definition stems from empirical measurements of total dissolved solids, though practical determinations rely on proxies like electrical conductivity due to the challenges of direct evaporation and weighing in variable compositions.[2]Historically, salinity was measured in parts per thousand (ppt or ‰), equivalent to grams of salt per kilogram of seawater (g/kg), with average open-ocean values around 35 ppt.[3] Since 1978, the international standard has been the Practical Salinity Scale (PSS-78), which defines salinity in practical salinity units (PSU or S_P), a dimensionless quantity calculated from the ratio of the sample's electrical conductivity to that of a standard potassium chloride (KCl) solution at 15°C and atmospheric pressure, using the formula S_P = a0 + a1 K^0.5 + a2 K + a3 K^1.5 + a4 K^2 + a5 K^2.5, where K is the conductivity ratio and coefficients a_i are empirically derived.[2][10] PSS-78 was adopted by UNESCO, SCOR, ICES, and IAPSO to standardize measurements for consistency in physical oceanography, as conductivity correlates closely with density and other properties without requiring full chemical analysis; numerically, 1 PSU approximates 1 ppt for typical seawater.[2]Absolute salinity (S_A), in contrast, denotes the true mass fraction of salts (g/kg), incorporating regional variations in composition not captured by conductivity alone, but PSS-78 remains the operational unit for most global datasets due to its reproducibility and historical continuity.[7] The transition to PSS-78 addressed inaccuracies in earlier chlorinity-based scales, improving precision for equations of state in seawaterthermodynamics.[2]
Chemical Composition of Saline Solutions
Saline solutions consist of water with dissolved inorganic salts, where sodium chloride (NaCl) predominates in many natural and artificial contexts, contributing sodium (Na⁺) and chloride (Cl⁻) ions as the primary cationic and anionic species, respectively.[11] In medical applications, normal saline is a 0.9% NaCl solution by mass, mimicking physiological fluid osmolarity with approximately 154 mM Na⁺ and 154 mM Cl⁻ per liter.[12] Natural saline waters, however, exhibit varied compositions depending on origin, with seawater serving as the canonical high-salinity example at approximately 35 grams of dissolved salts per kilogram of solution.[13]The ionic makeup of seawater remains proportionally constant across open ocean basins due to mixing and conservative behavior of major ions, unaffected by biological or short-term physical processes.[14] Six principal ions—Na⁺, Mg²⁺, Ca²⁺, K⁺, Cl⁻, and SO₄²⁻—account for over 99% of total dissolved salts by mass.[14] Chloride and sodium comprise the largest fractions, reflecting NaCl's dominance, while minor ions like bicarbonate (HCO₃⁻) and bromide (Br⁻) contribute less than 1% combined.[11]
Ion
Concentration (g/kg) at S=35
Percentage of Total Salts (%)
Cl⁻
19.35
55.07
Na⁺
10.76
30.61
SO₄²⁻
2.71
7.68
Mg²⁺
1.29
3.69
Ca²⁺
0.41
1.16
K⁺
0.40
1.10
These values derive from empirical analyses of standard seawater, such as IAPSO reference material, ensuring reproducibility in salinity measurements via chlorinity titration or conductivity.[15] In continental saline systems, such as groundwater brines or salt lake effluents, compositions deviate; for instance, calcium sulfate (gypsum) or sodium carbonate may dominate over NaCl due to evaporative concentration and mineralprecipitation sequences governed by solubility products.[16] Trace elements, including metals like iron and nutrients like nitrate, occur at microgram-per-liter levels but influence biogeochemical cycles without altering bulk salinity.[13]
Historical Development of Salinity Concepts
Ancient philosophers, including Aristotle, proposed early theories on the origin of seawater salinity, attributing it to dissolved salts from land runoff or evaporation cycles.[17] Pliny the Elder provided one of the first quantitative estimates around 77 AD, suggesting that sea salt content could be extracted to produce a volume equivalent to one-thirtieth of the water's weight through evaporation.[17]In the 19th century, chemical analyses advanced the understanding of salinity as the total mass of dissolved salts per kilogram of seawater.[18] Alexander Marcet observed in the 1820s that seawater composition was remarkably uniform across ocean basins, enabling chlorinity—the chlorideion concentration—as a reliable proxy for total salinity due to constant ion ratios.[19] Johan Georg Forchhammer's work in 1829 further confirmed these proportions, coining "chlorinity" and establishing empirical ratios like salinity approximating 1.80655 times chlorinity in grams per kilogram.[19] The Challenger expedition (1872–1876) provided extensive data, with William Dittmar's analyses validating the constancy of major ion ratios, such as sodium-to-chloride at 0.550, underpinning salinity calculations via titration methods.[20]At the International Council for the Exploration of the Sea (ICES) founding in 1899–1901, Martin Knudsen standardized salinity determination.[21] He introduced Standard Seawater—a filtered, preserved Baltic sample with certified chlorinity—for calibrating titration bottles, ensuring inter-laboratory consistency.[22] Knudsen's 1901 Hydrographical Tables defined salinity S = 0.03 + 1.805 \times Cl, where Cl is chlorinity in grams per kilogram, applicable for seawater densities near 1.025 kg/L.[18] This chlorinity-based approach dominated until the mid-20th century, though it assumed fixed composition and overlooked minor variations in other ions.[20]By the 1960s, conductivity measurements offered faster, non-destructive alternatives to titration, prompting reevaluation of salinity definitions.[2] The Practical Salinity Scale 1978 (PSS-78), developed by UNESCO, ICES, SCOR, and IAPSO, redefined salinity as a dimensionless value S_P via the equation relating seawaterconductivity at 15°C, atmospheric pressure, to a standard potassium chloride solution: S_P = a_0 + a_1 R^{1/2} + a_2 R + a_3 R^{3/2} + a_4 R^2 + a_5 R^{5/2}, where R is the conductivity ratio.[10] This scale, calibrated against Knudsen values for continuity, better accounted for empirical conductivity-salinity relations without requiring total saltmass, though it deviates from absolute salinity by about 0.25% due to unmeasured nutrients and organics.[23] PSS-78 remains the standard for oceanographic applications, reflecting a shift from chemical proxies to practical, electrically measurable parameters.[24]
Measurement Techniques
Traditional Laboratory Methods
Traditional laboratory methods for measuring salinity primarily relied on chemical titration techniques and gravimetric analysis, which directly quantified dissolved salts or key ions like chloride. These approaches, developed in the late 19th and early 20th centuries, provided foundational standards for oceanographic research before the widespread adoption of conductivity-based instruments.[21][25]The Knudsen method, introduced by Danish oceanographer Martin Knudsen in the early 1900s, became the international standard for chlorinity determination, from which salinity was calculated. This titration procedure involved precipitating chloride ions in a seawater sample with silver nitrate using a specialized burette and pipette system, compared against batches of IAPSO Standard Seawater certified for consistent composition. Chlorinity (Cl), expressed in grams of chloride per kilogram of seawater, was converted to salinity (S) via the empirical relation S = 1.80655 × Cl, yielding accuracy within 0.002 practical salinity units for typical seawater.[20][22][26]Prior to Knudsen's innovations, gravimetric methods determined salinity by evaporating a known mass of seawater to dryness and weighing the residual salts, offering a direct measure but prone to losses from volatile components and requiring large sample volumes. This evaporation technique, used since the 19th century, achieved precisions around 0.1% but was labor-intensive and insensitive to specific ionic compositions.[25][27]Early conductometric approaches emerged in the 1930s with devices like the Wenner-Smith-Soule salinity bridge, measuring electrical conductivity relative to standard seawater to infer salinity, bridging chemical and modern instrumental methods with reproducibilities better than 0.01 parts per thousand. These lab techniques emphasized precise temperature control, as conductivity varies inversely with salinity and directly with temperature.[28][22]
In Situ and Remote Sensing Methods
In situ measurements of salinity involve direct sampling and sensing within the aquatic environment, typically using instruments deployed from ships, buoys, floats, or autonomous underwater vehicles. The predominant method employs conductivity-temperature-depth (CTD) profilers, which calculate salinity from the electrical conductivity of seawater, corrected for temperature and pressure using the Practical Salinity Scale (PSS-78) or the more thermodynamically consistent Absolute Salinity framework under TEOS-10 conventions.[29][30] These devices achieve precisions of approximately 0.001–0.002 practical salinity units (psu) in standard oceanographic deployments, with shipboard CTD casts providing vertical profiles down to depths exceeding 5,000 meters.[29] Continuous underway measurements near the sea surface are facilitated by thermosalinographs, which pump seawater through flow-through conductivity cells, enabling high-frequency sampling at rates up to 1 Hz during vessel transits.[29]Emerging in situ techniques leverage optical properties for salinity inference, bypassing conductivity's sensitivity to biofouling and electrode drift. Refractive index-based sensors, such as those using total internal reflection or Michelson interferometry, detect shifts in light propagation caused by salinity-induced changes in seawater's index of refraction, offering resolutions around 0.01 psu and suitability for long-term deep-sea moorings.[31][30] Density-derived approaches measure absolute salinity via in situ densitometers combining refractive index interferometry with temperature, achieving uncertainties below 0.001 kg/m³ in density, which translates to salinity precisions of ~0.005 psu after accounting for equation-of-state relations.[32] Platforms like Argoprofiling floats and gliders extend these capabilities globally, with over 3,800 active floats as of 2023 providing salinity data at 2,000-meter depths every 10 days, though limitations include sparse coverage in polar and marginal seas and potential biases from regional composition anomalies not captured by conductivity alone.[29][33]Remote sensing of salinity primarily targets sea surface salinity (SSS) via satellite-borne microwave radiometers operating in the L-band (1–2 GHz), where seawater's dielectric constant—and thus microwaveemissivity—varies linearly with salinity at fixed temperature and frequency.[34] The Soil Moisture and Ocean Salinity (SMOS) mission, launched in 2009 by the European Space Agency, uses interferometric aperture synthesis to map SSS with a nominal spatial resolution of 35–50 km and accuracy of 0.1–0.2 psu in open oceans, though rain contamination and radio-frequency interference degrade performance near coasts.[34][35] NASA's Aquarius (2011–2015) and Soil Moisture Active Passive (SMAP, 2015–present) instruments refined retrieval algorithms by incorporating ancillary data on sea surface temperature, wind speed, and roughness to mitigate diurnal skin-layer effects, yielding global SSS fields at 40–150 km resolution with root-mean-square errors of ~0.2 psu against in situ validations after 2015 enhancements.[36][34]These remote methods probe only the top 1–10 mm of the ocean skin layer, introducing discrepancies with subsurface in situ observations (typically at 5–10 m depths) due to vertical gradients from evaporation, precipitation, or upwelling, with differences up to 0.5 psu in stratified regions.[37]Calibration relies on merging satellite data with in situ networks like Argo, enabling multi-mission products such as the Copernicus Marine Service SSS fields, which achieve temporal resolutions of daily composites but require corrections for galactic noise and land proximity artifacts.[35] Overall, remote sensing complements in situ sparsity by providing synoptic coverage, yet its utility for bulk salinity remains limited without integration, as electromagnetic penetration depth precludes subsurface profiling.[38]
Salinity in Marine Environments
Characteristics of Seawater Salinity
Seawater salinity averages 35 practical salinity units (PSU), corresponding to roughly 35 grams of dissolved salts per kilogram of seawater, though precise measurements reference a standardized composition where practical salinity of 35 equates to a reference-composition salinity of 35.16504 g/kg.[39][40] This salinity arises primarily from dissolved inorganic ions, with over 99% consisting of six major constituents: chloride (Cl⁻), sodium (Na⁺), sulfate (SO₄²⁻), magnesium (Mg²⁺), calcium (Ca²⁺), and potassium (K⁺).[41]The relative proportions of these major ions remain nearly constant throughout the oceans, exhibiting conservative behavior where their concentrations scale linearly with total salinity due to minimal biological or chemical removal processes compared to nutrient elements.[42][13] Sodium and chloride ions dominate, accounting for approximately 85% of the total dissolved salts, while the remainder includes sulfate, magnesium, calcium, and potassium in fixed ratios.[42]
Ion
Concentration (g/kg at S=35)
Percentage of Total Salinity
Cl⁻
19.35
55.07%
Na⁺
10.76
30.61%
SO₄²⁻
2.71
7.72%
Mg²⁺
1.29
3.68%
Ca²⁺
0.41
1.17%
K⁺
0.40
1.14%
This table represents the standard ionic composition for seawater at 35 PSU, derived from empirical analyses of Atlantic surface water used as a reference.[15] Minor ions and trace elements, such as bicarbonate and bromide, contribute less than 1% but influence properties like pH and buffering capacity.[41] The uniformity in major ion ratios enables salinity to be estimated from measurements of any single conservative ion, such as chlorinity, historically linking salinity to chloride content via the relation S ≈ 1.80655 × Cl.[13]Practical salinity is now defined conductometrically on the UNESCO scale, calibrated against standard seawater batches prepared to mimic natural oceanic composition, ensuring global consistency in measurements despite regional salinity variations from 32 to 37 PSU.[19] This standardization accounts for the fact that seawater salinity includes not only salts but also minor organic and inorganic contributions, though these are negligible for bulk properties.[13]
Spatial and Temporal Variations in Oceans
Ocean salinity exhibits pronounced spatial variations primarily driven by the balance between evaporation, precipitation, river runoff, and ice formation or melt. Sea surface salinity (SSS) typically ranges from 32 to 37 practical salinity units (PSU) globally, with higher values in subtropical regions where evaporation exceeds precipitation, such as the Atlantic and Pacific gyres, often exceeding 36 PSU.[39] Lower salinities, around 32-34 PSU, occur near the equator due to heavy rainfall and in high latitudes from sea ice melt and river inputs, including the Arctic and Antarctic marginal seas.[43] In the Southern Ocean, SSS decreases toward the ice edge, with meridional gradients reflecting poleward freshening from ice melt and equatorward salinification via evaporation.[44]The Atlantic generally maintains higher basin-wide salinity than the Pacific due to stronger evaporation minus precipitation (E-P) fluxes and less dilution from runoff.[45]Vertically, salinity profiles show subsurface maxima in many regions from evaporation concentrating salts at the surface and mixing downward, while deep ocean waters remain more uniform at 34.5 to 35 PSU owing to reduced freshwater fluxes and thermohaline circulation homogenizing properties.[46]Ocean currents further modulate spatial patterns by advecting high-salinity waters equatorward and low-salinity waters poleward, as seen in the equatorial Indian Ocean where inter-basin exchanges influence zonal gradients.[47]Temporal variations occur on seasonal to interannual scales, superimposed on spatial patterns. Seasonally, SSS maxima align with dry periods of high evaporation, such as December to April in subtropical regions, while minima coincide with rainy seasons or ice melt, for instance decreasing from September to March in the SPURS region of the subtropical North Atlantic.[48] In tropical areas, seasonal SSS fluctuations of 1-2 PSU arise from monsoon-driven precipitation and E-P imbalances, with satellite observations from SMOS and SMAP confirming cycles near major river mouths like the Amazon.[49] Interannually, variations stem from climate modes like ENSO, which alter precipitation patterns and river discharge, leading to SSS anomalies of 0.5-1 PSU in the eastern tropical Pacific and Indian Ocean.[50] In the Northeast U.S. shelf, interannual salinity shifts are linked to Gulf Stream variability and freshwater inputs, with recent Argo data revealing decadal freshening trends in some mid-latitude bands.[51]Longer-term trends indicate amplification of salinity contrasts, with high-salinity regions becoming saltier and low-salinity areas fresher, consistent with enhanced global water cycle intensity from warming-induced E-P changes observed since the 1950s.[52] These dynamics underscore salinity's role in density-driven circulation, where spatial and temporal freshwater fluxes influence thermohaline stability.[45]
Influence on Ocean Dynamics and Circulation
Salinity exerts a primary influence on ocean dynamics through its effect on seawater density, as described by the thermodynamic equation of state, which relates density to temperature, salinity, and pressure. Higher salinity increases density at a given temperature and pressure, approximately by 0.78 kg/m³ per practical salinity unit (psu), facilitating the downward displacement of water masses in regions of excess evaporation or sea ice formation where salt is concentrated.[53][54] This density augmentation underpins the thermohaline component of ocean circulation, where dense, saline waters sink and drive large-scale meridional overturning.[55]In the global thermohaline circulation—commonly visualized as the ocean conveyor belt—salinity gradients enable the formation of deep and bottom waters, particularly in the North Atlantic, where surface waters achieve salinities exceeding 35 psu due to evaporative losses exceeding precipitation. This process generates North Atlantic Deep Water (NADW), which sinks below 2000 meters and flows southward, pulling surface waters northward to replace it and thereby linking hemispheric circulation patterns.[56][57] The conveyor belt's vigor depends on sustained salinity contrasts; for instance, net atmospheric water vapor transport from the Atlantic to the Pacific maintains the Atlantic's higher baseline salinity, preventing widespread stagnation despite comparable polar cooling.[58]Salinity also modulates ocean stratification and vertical mixing by establishing haloclines—sharp density gradients that resist turbulent exchange between layers. In subtropical gyres, elevated surface salinities reinforce a stable pycnocline, limiting mixed-layer deepening and constraining upwelling of nutrients and heat. Conversely, freshwater influxes from Arctic river discharge or glacial melt lower surface salinity, intensifying stratification and potentially decelerating overturning rates, as observed in model simulations where salinity anomalies weaken upper-ocean entrainment by up to 20-30%.[59][60] Such dynamics influence eddy formation and frontal instabilities, where salinity fronts can amplify mesoscale variability and enhance lateral mixing over vertical processes.[61]
Salinity in Continental and Terrestrial Systems
Salinity in Freshwater Bodies and Rivers
Freshwater bodies, including rivers and lakes, characteristically maintain low salinity levels, typically defined as less than 0.5 parts per thousand (ppt) or 1,000 milligrams per liter (mg/L) of total dissolved solids (TDS), distinguishing them from brackish or saline waters.[62][63] This low salinity arises primarily from the dilution effects of precipitation and minimal ion accumulation compared to marine environments, with river waters often registering below 0.1 ppt in pristine conditions.[64] Geological factors, such as the weathering of carbonate and silicate rocks, contribute natural ions like calcium, magnesium, sodium, and chloride, while atmospheric deposition and aerosol inputs add trace salts via rainfall.[65] In undisturbed systems, these processes yield stable, low-salinity profiles, with specific conductance (a proxy for salinity) rarely exceeding 500 microsiemens per centimeter (µS/cm) in temperate rivers.[66]Anthropogenic activities have increasingly elevated salinity in these systems, a phenomenon termed freshwater salinization syndrome (FSS), driven by sources including road deicing salts, wastewater effluents, agricultural irrigation return flows, and mining runoff.[66][67] For instance, winter application of sodium chloride for deicing in northern regions can spike chloride concentrations in streams by factors of 10 to 100 during snowmelt, with baseline levels of 10-50 mg/L rising to over 1,000 mg/L in urban-impacted watersheds.[68] Human-accelerated weathering from construction and urbanization further mobilizes ions, while sewage and fertilizer applications introduce potassium and nitrogen compounds that indirectly boost salinity through ion exchange.[69] In the United States, monitoring data from the early 1900s to 2010s indicate widespread upward trends in river salinity, particularly in the Northeast and Midwest, where chloride doubled or tripled in many basins due to these inputs.[70][71]Spatial and temporal variations in freshwater salinity reflect catchment geology, hydrology, and land use; for example, rivers draining arid, evaporite-rich basins like those in the western U.S. naturally exhibit higher baseline TDS (200-500 mg/L) from gypsum dissolution, whereas humid tropical rivers remain below 50 mg/L.[65] Seasonal fluctuations occur, with dilution during high-flow events reducing salinity by up to 50% and concentration during dry periods or baseflow amplifying it through evaporation and reduced flushing.[72] In lakes, stratification can lead to denser, saltier bottom waters in meromictic systems, though most dimictic lakes homogenize annually with salinities under 100 mg/L.[64] Ongoing salinization trends, documented globally since the 1980s, pose risks to water usability, with projections indicating further increases in urbanizing areas absent mitigation, as salts persist in sediments and groundwater for decades post-input.[73][74]
Hypersaline Lakes and Inland Basins
Hypersaline lakes form in endorheic basins—closed drainage systems lacking outlets to the sea—where evaporation rates exceed precipitation and inflow, leading to progressive salt concentration.[75] These environments typically exhibit salinities exceeding 70 g/kg (twice seawater's average of ~35 g/kg), though definitions vary, with some thresholds at >35 g/L for brines up to 350 g/L.[76][77] Salinization mechanisms include evaporative enrichment of dissolved ions from catchment runoff, aeolian salt deposition, and subsurface brineupwelling, often dominated by sodium chloride alongside magnesium, calcium, and sulfate salts.[78] In arid climates, such as those in the Great Basin or Middle East, annual evaporation can concentrate salts by factors of 2–10 times seawater levels within decades of basin isolation.[79]The Dead Sea exemplifies extreme hypersalinity, with surface salinity reaching 342 g/kg (34.2%) as of 2011, driven by Jordan River inflow diminished by upstream diversions and high evaporation rates of ~1,800 mm/year.[80] Its density exceeds 1.24 g/cm³, enabling human flotation, and vertical stratification traps denser brines below 300 m depth, where salinity approaches saturation.[81] Similarly, the Great Salt Lake in Utah varies from 50–270 g/kg across arms, with the south arm historically 60–270 g/kg due to a railroad causeway restricting mixing; post-2021 monitoring shows densities correlating to salinities via equations validated against field data, reflecting inflows from the Bear and Weber Rivers diluted by rare wet periods.[82][83] Inland basins like the Qaidam in China host ephemeral hypersaline pools exceeding 200 g/kg, formed by tectonic subsidence trapping evaporites from Miocenemarine incursions.[78]Salinity in these systems fluctuates with climate: drought intensifies evaporation, precipitating halite crusts and mirabilite, while pluvial episodes dilute brines, as seen in Great Salt Lake's 1980s levels dropping below 100 g/kg before rebounding.[79]Measurement relies on conductivity probes calibrated for high densities, with lab validation using gravimetric analysis; USGS data from 2021–2022 confirm Great Salt Lake salinities via empirical state equations accounting for ion complexes.[83] Ecologically, hypersalinity limits biodiversity to haloarchaea and brine shrimp, with thresholds above 150 g/kg excluding most metazoans, though these lakes preserve microbial biosignatures in evaporite minerals, informing astrobiology.[84] Human alterations, including water diversions, have accelerated desiccation in basins like the Dead Sea, reducing volume by 30% since 1960 and elevating salinity further.[80]
Soil and Groundwater Salinity Patterns
Soil salinity patterns exhibit pronounced spatial clustering in arid and semi-arid regions, where low precipitation and high evapotranspiration rates promote salt accumulation through capillary rise from shallow groundwater and surface evaporation. Globally, approximately 10% of land surfaces—predominantly in North and Central Asia, Africa, and South America—feature saline soils with electrical conductivity exceeding 4 dS/m in saturated extracts, thresholds that impair crop yields for sensitive species.[85][86] Primary salinization arises from natural processes including rock weathering, aeolian salt deposition, and episodic flooding, while secondary patterns dominate in irrigated lowlands, driven by poor drainage and use of brackish water, affecting over 20% of global irrigated lands as of 2021.[87][88]Temporal dynamics in soil salinity intensify during dry seasons, with salt concentrations rising 20-50% due to reduced leaching and heightened evaporation, as observed in monitoring studies across semi-arid basins; long-term trends project a 25-100% increase in salinized area by 2050 under continued irrigation expansion and warming climates that elevate evapotranspiration by 5-10% per degree Celsius.[89][90] Coastal zones display hybrid patterns, where sea-level rise—averaging 3.7 mm/year globally since 2006—exacerbates intrusion, leading to salinity gradients that advance inland at rates of 10-100 meters per decade in overexploited aquifers.[91][92]Groundwater salinity patterns parallel soil distributions but reflect deeper geohydrological controls, with spatial heterogeneity marked by salinity plumes in confined aquifers ranging from freshwater (<1,000 mg/L total dissolved solids) to brackish (1,000-10,000 mg/L) zones, often increasing with depth due to fossil seawater or mineral dissolution.[93] In coastal settings, saltwater intrusion forms density-driven wedges, penetrating 1-10 km inland where hydraulic gradients favor seawater over freshwater, accelerated by pumping rates exceeding recharge by factors of 2-5 in regions like California's Central Valley.[94] Temporal variations track seasonal recharge deficits and drought cycles, with salinity spikes of 10-30% during low-precipitation years from diminished dilution and upconing of deeper brines; projections indicate widespread potable water loss in U.S. coastal aquifers by 2100 under high-emission scenarios.[95][96] Interactions between soil and groundwater manifest as reciprocal feedbacks, where rising saline tables—elevated 1-2 meters in overirrigated areas—induce surface salinization via evapotranspiration, forming patterned crusts in playas and alluvial fans.[97][98]
Biological and Ecological Consequences
Adaptations and Tolerance in Aquatic Organisms
Aquatic organisms exhibit two primary strategies for coping with salinity: osmoconformity, where internal osmotic concentration matches the external environment, and osmoregulation, where internal conditions are actively maintained against environmental gradients.[99] Osmoconformers, prevalent among marine invertebrates such as echinoderms, cnidarians, and many mollusks, minimize energy expenditure by allowing body fluids to equilibrate with seawater's typical salinity of 32–37 parts per thousand (ppt), relying on organic osmolytes like amino acids to stabilize proteins without precise ion control.[100] In contrast, osmoregulators, including most teleost fishes and crustaceans, invest metabolic energy to maintain internal salinity at levels distinct from the surroundings; marine teleosts, for example, hypo-osmoregulate by excreting monovalent ions via chloride cells in gills and producing iso-osmotic urine, while ingesting seawater to offset diffusive water loss across permeable gills.[101]Euryhaline species, capable of tolerating wide salinity fluctuations (often 0–60 ppt or more), possess plastic physiological mechanisms such as inducible ion transporters (e.g., Na+/K+-ATPase) and hormonal regulation via cortisol and prolactin to shift between freshwater hyperosmoregulation and marine hypo-osmoregulation.[101] Examples include the Atlantic salmon (Salmo salar), which migrates between freshwater (salinity ~0 ppt) and full seawater (35 ppt), enduring up to 40 ppt during smoltification via gill remodeling, and the mummichog (Fundulus heteroclitus), which survives acute shifts from 0 to 100 ppt through rapid adjustments in gill permeability and urea accumulation.[102] Stenohaline species, conversely, exhibit narrow tolerance ranges; most marine stenohalines fail below 20 ppt due to osmotic swelling, while freshwater stenohalines succumb above 10–15 ppt from ion overload.[102]Empirical data from laboratory acclimation trials indicate upper salinity tolerances vary by taxon: marine fishes generally withstand 40–50 ppt chronically, with euryhaline tilapias (Oreochromis spp.) reaching 50–60 ppt before gill hyperplasia impairs gas exchange.[102] Invertebrates show greater extremes; brine shrimp (Artemia salina) thrive in hypersaline environments up to 300 ppt via extracellular hemolymph regulation and cyst diapause, while many estuarine crabs (Carcinus maenas) tolerate 5–45 ppt through behavioral burial and ionic adjustments.[103] Planktonic organisms, including diatoms, adapt via gene expression changes in ion channels and compatible solutes under fluctuating salinities, with species like Thalassiosira weissflogii maintaining growth across 15–40 ppt but exhibiting reduced photosynthesis beyond 50 ppt.[104]Tolerance limits are influenced by acclimation time, temperature, and life stage; juveniles often have lower thresholds than adults, as seen in fish where larval stages of seabass (Dicentrarchus labrax) tolerate only up to 45 ppt versus 55 ppt for adults.[102] Sublethal stress from chronic exposure includes elevated metabolic rates (up to 30% increase in euryhalines at salinity extremes) and oxidative damage, mitigated by antioxidants like glutathione in tolerant species.[103] These adaptations underscore causal links between salinity gradients and selective pressures, with empirical tolerances derived from controlled exposures rather than field correlations alone.[101]
Effects on Terrestrial Ecosystems and Agriculture
Soil salinization imposes osmotic stress on plants by lowering the soil solution's water potential, restricting root water uptake, and causing ion toxicity from excess sodium and chloride accumulation, which disrupts cellular functions and nutrient balance. These physiological effects manifest as reduced photosynthesis, stunted growth, and diminished biomass production, with sensitive crops exhibiting chlorosis and necrosis at electrical conductivity levels exceeding 4 dS/m. For instance, high salinity impairs potassium and calcium uptake while promoting sodium influx, leading to membrane depolarization and oxidative damage in root tissues.[105][106][107]In agriculture, salinization reduces crop yields globally, affecting approximately 33% of irrigated lands and contributing to productivity losses of up to 70% for staples like rice and beans in severely impacted regions. Empirical data indicate that moderate salinity (e.g., 5-10 dS/m) can decrease wheat yields by 20-40%, while extreme levels render soils unproductive, as observed in cases where over 600,000 hectares in certain arid zones have been damaged, forcing land abandonment. Salt-tolerant crops such as barley may sustain yields under 8 dS/m, but overall, salinization exacerbates food insecurity by limiting arable land expansion and increasing irrigation demands in marginal areas.[108][109][110]Terrestrial ecosystems experience biodiversity declines from salinization, as it favors halophytic species over diverse native flora, altering plant community structure and reducing habitat suitability for fauna dependent on vegetation cover. Soil microbial communities suffer suppressed activity, with salinity disrupting nitrogen fixation and organic matter decomposition, thereby impairing nutrient cycling and soil fertility; studies show decreased litter saprotroph abundance and elevated pathogen prevalence under saline conditions. Long-term, this promotes land degradation and desertification, as evidenced by empirical models linking salinity gradients to ecosystem dysfunction in coastal and inland drylands, where salt buildup disperses soil aggregates and erodes structural stability.[89][111][86]
Interactions with Biodiversity and Food Webs
Salinity serves as a key abiotic factor structuring aquatic biodiversity by imposing physiological constraints on organismal osmoregulation, distribution, and community assembly. In marine ecosystems, where salinity typically ranges from 32 to 37 practical salinity units (psu), stable conditions support diverse assemblages of phytoplankton, zooplankton, and higher trophic levels, but deviations—such as hypersalinity exceeding 40 psu—reduce species richness by favoring halotolerant extremophiles while excluding less adapted taxa.[68] Empirical studies indicate that biodiversity peaks at intermediate salinities and declines sharply above 10-15 psu in transitional environments, reflecting tolerance thresholds where ion regulation costs escalate, limiting metabolic energy for growth and reproduction.[68]In estuarine systems, salinity gradients from freshwater inflows to marine influences create distinct ecological zones that drive spatial patterns in biodiversity and trophic interactions. Oligohaline zones (0.5-5 psu) harbor freshwater-dominated communities with high plant and invertebrate diversity, transitioning to mesohaline (5-18 psu) and polyhaline (18-30 psu) zones where marine species ingress, compressing habitats and altering assemblage composition.[112] These gradients influence food web structure by modulating primary production; for instance, phytoplankton diversity and biomass shift along salinity clines, with euryhaline diatoms dominating lower salinities and supporting zooplankton grazers, while higher salinities favor picoplankton that propagate up the chain to fish and birds.[113] Disruptions, such as reduced river flows elevating salinity, can trigger trophic cascades, as seen in coastal wetlands where salinity increases diminish benthic microalgae, reducing prey for detritivores and cascading to fishery declines.[114]Hypersalinity events, often anthropogenic, further erode biodiversity by exceeding tolerance limits of most marine taxa, leading to community homogenization and simplified food webs. In hypersaline lagoons (e.g., >50 psu), microbial mats and brine shrimp dominate, supporting limited predators like flamingos, but excluding diverse fish and mollusks, which results in reduced trophic complexity and resilience.[115] Laboratory and field data show plankton density and diversity plummet with salinity rises from ballast water discharges, disrupting basal food web links and amplifying effects through bioaccumulation in predators.[116] In riverine and inland systems, salinization from irrigation runoff correlates with 20-50% losses in macroinvertebrate richness, altering energy flows from allochthonous detritus to autochthonous algae and impacting migratory fish populations.[117]Overall, salinity-biodiversity interactions underscore causal linkages where osmotic stress filters communities, with food webs exhibiting vulnerability to rapid changes; meta-analyses confirm that even modest increases (2-5 psu) can shift dominance from sensitive to tolerant species, potentially destabilizing ecosystem services like nutrient cycling and habitat provision.[118] These patterns hold across scales, from microbial loops in oceans to vertebrate chains in estuaries, emphasizing salinity's role in maintaining or eroding ecological stability.[119]
Human Activities and Salinity Alterations
Anthropogenic Sources of Salinity Changes
Agricultural practices, particularly irrigation in arid and semi-arid regions, constitute a primary anthropogenic driver of secondary soil salinization, where evaporation of irrigated water leaves behind dissolved salts that accumulate in the root zone and percolate into groundwater.[105] Globally, improper irrigation management affects approximately 20-50% of irrigated lands, exacerbating salinity levels and rendering soils unproductive for crops sensitive to salt stress.[86] In the United States, irrigated agriculture significantly elevates salt loads in rivers and aquifers through mobilization of ions from soils, with studies showing correlations between irrigation intensity and downstream salinity increases independent of natural geology.[120]Winter road deicing with sodium chloride (NaCl) salts introduces substantial chloride and sodium ions into freshwater systems via stormwater runoff, leading to year-round salinization in urban and suburban watersheds.[121] In northern climates, road salt application has caused chloride concentrations in some streams to exceed 100 mg/L, surpassing ecological thresholds and accumulating in sediments and groundwater over decades.[122] For instance, one teaspoon of road salt can contaminate five gallons of water, contributing to broader freshwater salinization syndrome that disrupts aquatic chemistry and biota.[123] This pollution is amplified in areas with high impervious surfaces, where minimal dilution occurs during non-winter periods.[124]Desalination plants, proliferating in water-scarce coastal regions, discharge hypersaline brine that locally elevates marine salinity by 1-5% near outfalls, potentially extending over kilometers depending on ocean currents and discharge design.[125] In enclosed basins like the Arabian Gulf, cumulative brine from multiple facilities has contributed to basin-wide salinity rises of up to 0.5-1 practical salinity units (psu) over decades, stressing benthic communities including corals and seagrasses.[126]Brine also carries residual chemicals and elevated temperatures, compounding impacts beyond salinity alone.[127]Industrial activities such as mining and oil extraction release saline effluents and brines from produced waters, contaminating surface and groundwater with elevated total dissolved solids (TDS). In oil sands processing, high-salinity wastewaters can leach metals and salts into adjacent aquifers if not managed, with salinity levels exceeding 10,000 mg/L in untreated discharges. Human-induced groundwater over-pumping and canal construction further promote saltwater intrusion in coastal aquifers, advancing salinization fronts inland by meters to kilometers annually.[128]Anthropogenic climate change, through greenhouse gas emissions driving sea-level rise of approximately 3.7 mm per year since 2006, facilitates saltwater intrusion into coastal freshwater systems, contaminating aquifers and estuaries. By 2100, projections indicate that 77% of global coastal areas below 60°N could experience significant intrusion, with combined effects of sea-level rise and extraction rendering groundwater unusable in vulnerable deltas. In estuaries, future salt limits are expected to increase by a median 9.1%, altering mixing zones and freshwater availability.[129][130]
Desalination Processes and Technological Advances
Desalination refers to technologies that remove dissolved salts from saline water, primarily seawater with typical salinity levels of 35 grams per liter, to produce potable or industrial water. The process separates saline feedwater into fresh product water and concentrated brine, addressing water scarcity in arid regions. Globally, desalination capacity exceeded 150 million cubic meters per day by 2025, with reverse osmosis (RO) accounting for the majority of installations due to its scalability and lower energy demands compared to thermal methods.[131]The predominant desalination method, reverse osmosis, operates on the principle of applying hydraulic pressure exceeding the osmotic pressure of seawater—typically 50-80 bar—to force water molecules through a semi-permeable membrane, rejecting salts and impurities. Modern RO systems achieve salt rejection rates above 99%, producing water with salinity below 500 mg/L suitable for drinking. Energy consumption for seawater RO has declined to 2.5-4.0 kWh per cubic meter through optimized pumps and pretreatment, representing a significant improvement from early systems that required over 10 kWh/m³.[132][131]Thermal desalination processes, such as multi-stage flash (MSF) and multi-effect distillation (MED), rely on heat to evaporate water, followed by condensation to separate it from salts. MSF involves flashing heated seawater into vapor across multiple pressure stages, while MED reuses vapor heat across evaporator effects for higher efficiency. These methods suit integration with thermal power plants, where waste heat reduces effective energy costs, but they consume 10-15 kWh thermal equivalent per cubic meter, making them less competitive for standalone operations without cogeneration. Thermal processes comprise about 20-30% of global capacity, often in the Middle East where electricity is subsidized.[133][134]Emerging membrane technologies address fouling and permeability limitations in RO, including anti-fouling coatings and thin-film nanocomposite membranes that boost water flux by 20-50% while maintaining selectivity. Pressure exchanger devices recover up to 97% of energy from high-pressure brine, cutting overall electricity use by over 50% in large plants. Hybrid systems combining RO with forward osmosis or electrodialysis enhance recovery rates from brackish sources with salinities of 1,000-10,000 mg/L.[132][135]Recent advances integrate renewables to mitigate desalination's global energy footprint of approximately 75-100 TWh annually, equivalent to 0.4% of world electricity. Solar-thermal or photovoltaic-powered RO systems, such as a 2023 MIT prototype using shockwave-assisted evaporation, aim to produce freshwater at costs below tap water in sunny regions. Geothermal-RO hybrids, tested in 2024-2025 pilots, leverage low-grade heat for pretreatment, potentially reducing operational expenses by 30%. Uniform density desalination membranes and closed-circuit RO configurations further minimize waste brine volumes, addressing environmental concerns over hypersaline discharge. These innovations have lowered levelized costs to as low as 0.3 USD per cubic meter for seawater RO in optimized facilities.[136][137][138][139]
Agricultural and Industrial Management Practices
Agricultural salinity management focuses on preventing salt buildup in irrigated soils through controlled water application and drainage. Leaching remains the core technique, involving the application of low-salinity water in excess of evapotranspiration needs to flush soluble salts below the root zone, with required leaching fractions typically ranging from 0.1 to 0.3 based on soil permeability, initial salinity (measured as electrical conductivity, ECe), and target crop thresholds.[140][141] For instance, in sodic soils, gypsum amendments (calcium sulfate dihydrate) at rates of 1-5 tons per hectare displace sodium ions, improving infiltration and enabling effective leaching when followed by drainage.[142] Surface and subsurface drainage systems, such as tile drains spaced 10-30 meters apart, remove leachate and prevent waterlogging, which exacerbates salinity; these have proven effective in reclaiming arid-region farmlands, reducing ECe from over 10 dS/m to below 4 dS/m within 1-3 years under optimal conditions.[143][141]Irrigation method selection further mitigates salinity risks by minimizing evaporative salt deposition. Drip and micro-sprinkler systems deliver water precisely to the root zone, achieving up to 90% application efficiency and limiting surface salt crusting compared to flood irrigation, which can concentrate salts via uneven wetting.[144] Crop management integrates salt-tolerant varieties, such as quinoa (Chenopodium quinoa) enduring ECe up to 12 dS/m or barley (Hordeum vulgare) at 8 dS/m, rotated with less tolerant species to maintain yields; this approach sustains productivity on marginal lands without full reclamation, as demonstrated in trials yielding 70-80% of non-saline benchmarks.[145][105]Agroforestry and cover cropping with halophytes like Atriplex spp. enhance soil structure and transpiration, reducing shallow groundwater rise that mobilizes salts, though adoption remains limited by initial costs exceeding $500 per hectare.[146]Industrial practices address salinity primarily through effluent pretreatment and brine concentration to curb discharge impacts on receiving waters. In sectors like thermoelectric power generation and mining, high-salinity cooling or process waters (often 5-50 g/L total dissolved solids) undergo segregation into saline streams, followed by membrane technologies such as reverse osmosis, which reject 95-99% of salts into a concentrated brine volume reduced by 50-75%.[147][148]Brine disposal methods include evaporation ponds, where solar drying achieves zero liquid discharge (ZLD) in arid climates, recovering solids for reuse (e.g., salts for de-icing) while minimizing hypersalinity plumes; facilities processing 100,000 m³/day brine report 80-90% volume reduction via multi-effect evaporation.[149][150] Deep-well injection, regulated to depths below 1,000 meters, confines brines geologically but risks induced seismicity if pressures exceed formation limits, as observed in some Permian Basin operations since 2010.[148] Emerging resource recovery integrates electrodialysis or crystallization to extract valuables like lithium (up to 90% recovery from oilfield brines at concentrations >200 mg/L), transforming waste into economic assets while complying with effluent standards limiting salinity increases to 5% at mixing zones.[151][152] These strategies, prioritized in frameworks like Australia's brine management guidelines updated in 2023, emphasize site-specific modeling to avoid ecological thresholds, though implementation lags in developing regions due to capital demands over $1 million per installation.[153]
Environmental Interactions and Long-Term Trends
Natural Variability and Geological Influences
Ocean salinity exhibits natural variability driven by the global water cycle, where evaporation removes freshwater from the surface, concentrating dissolved salts, while precipitation, river runoff, and ice melt introduce fresher water, diluting salinity. In subtropical gyres, evaporation rates exceed precipitation, resulting in surface salinities often exceeding 36 parts per thousand (ppt), whereas equatorial regions and high latitudes experience net freshwater input, yielding salinities below 34 ppt. Seasonal fluctuations amplify these patterns; for instance, during dry seasons in monsoon-influenced areas, reduced river discharge and heightened evaporation can elevate coastal salinities by 1-2 ppt.[15][154][155]Riverine inputs, modulated by continental hydrology, contribute significantly to regional variability, with major systems like the Amazon delivering approximately 20% of global freshwater discharge, locally reducing salinity by up to 5 ppt near outflows. Ice melt from glaciers and sea ice further influences polar and subpolar zones, where summer thawing can decrease surface salinity by 0.5-1 ppt annually in areas like the Arctic. Ocean circulation, including upwelling and mixing, redistributes these anomalies, but the primary drivers remain surface flux imbalances, with evaporation-precipitation differences accounting for over 80% of observed short-term changes in sea surface salinity.[62][156][157]Geological processes exert control over long-term salinity baselines through the delivery of ions via chemical weathering of continental rocks and hydrothermal activity at seafloor spreading centers. Rainwater, slightly acidic from dissolved carbon dioxide, erodes minerals like sodium and chloride from silicate and evaporite deposits, which rivers transport to oceans at rates estimated at 3-4 billion tons of salt per year. Mid-ocean ridge vents release additional salts, including magnesium and sulfate, balancing inputs against sedimentary removal. Over Phanerozoic timescales (past 541 million years), seawater salinity has declined from peaks around 40-50 ppt in the Paleozoic to the modern average of 35 ppt, attributed to reduced evaporite formation and increased freshwater cycling amid tectonic reconfiguration of ocean basins.[158][159][160]These geological inputs maintain a steady-state salinity despite variability, as excess salts precipitate in marginal seas or subduct with oceanic crust. Paleoceanographic proxies, such as fluid inclusions in halite deposits, confirm fluctuations tied to supercontinent cycles; for example, during the Permian (252 million years ago), restricted basins fostered hypersaline conditions exceeding 40 ppt locally. Such historical shifts underscore salinity's sensitivity to plate tectonics and eustatic sea-level changes, independent of anthropogenic influences./03:_New_Page/08:_The_Water_Cycle_and_Ocean_Salinity/8.05:_Salinity_over_Long_Timescales)[161]
Observed Salinity Shifts and Empirical Data
Empirical measurements from shipboard observations, Argo profiling floats, and satellite altimetry and radiometry missions reveal systematic shifts in ocean salinity patterns over the past several decades, characterized by an amplification of preexisting spatial contrasts. In evaporation-dominated subtropical regions, such as the Atlantic and Indo-Pacific gyres, sea surface salinity (SSS) has increased, with trends of approximately 0.09 g kg⁻¹ century⁻¹ in the Atlantic from 1960 to 2023. Conversely, precipitation-rich and high-latitude areas, including the Pacific tropics and subpolar North Atlantic, exhibit freshening, with Pacific SSS trends of -0.09 g kg⁻¹ century⁻¹ over the same period.[162]Quantitatively, the upper ocean (0–2000 m) salinity contrast index (SC2000), which measures the difference between high- and low-salinity regions, has risen by 5.2% ± 0.4% (equivalent to 0.028 ± 0.002 g kg⁻¹ century⁻¹) from 1960 to 2017, accelerating to 3.3% ± 0.4% in the 1991–2017 subperiod. Surface-only contrast (SC0) shows a steeper increase of 7.5% ± 0.9% (0.179 ± 0.014 g kg⁻¹ century⁻¹) over the full interval, reflecting intensified evaporation-precipitation differentials. These patterns hold after accounting for sampling biases, with signal-to-noise ratios of 6–10 indicating robustness.[163]Global mean salinity trends are subdued, with quality-controlled profiles from the CODC-S dataset indicating a slight upper-ocean (0–2000 m) freshening of -0.004 ± 0.002 g kg⁻¹ century⁻¹ through 2023, though 2002–2023 averages for the same layer show a minor increase of 0.0011 g kg⁻¹. Argo floats, operational since 2000 and providing over 11 million profiles to date, underpin these findings with near-global coverage to 2000 m depths every 10 days, but raw data post-2015 exhibit salty biases from sensor drift (up to 0.01–0.02 psu), which quality-control procedures mitigate to preserve trend reliability.[162][164]Regional specifics include salinification in the subtropical Atlantic (e.g., 0.3 psu over 50 years in some gyre cores) and freshening in the Southern Ocean and Arctic inflows, consistent across in situ and satellite datasets like NASA's Aquarius mission (2011–2015) and subsequent SMAP observations. These shifts, while regionally pronounced, do not alter global mass balance significantly, as vertical mixing and circulation redistribute salts.[163][165]
Causal Attribution and Scientific Debates
Observed patterns of ocean salinity amplification, characterized by freshening in high-latitude and equatorial precipitation-dominated regions alongside salinification in subtropical evaporation-dominated gyres, have been attributed primarily to anthropogenic influences through the intensification of the global hydrological cycle driven by greenhouse gas emissions.[166]Climate model simulations incorporating historical anthropogenic forcings replicate these spatial patterns, with salinity contrasts increasing at rates of approximately 8% per degree of surface warming since the mid-20th century, whereas ensembles driven solely by natural variability (e.g., solar and volcanic forcings) fail to match the observations.[166] This "fingerprint" method, applied to data from ship-based measurements and Argo floats since the 1950s, indicates that human-induced changes account for the bulk of the multi-decadal trends, estimated at 0.1 to 0.3 practical salinity units (psu) per decade in key regions like the subtropical North Atlantic.[167]Natural drivers, including ocean circulation variability (e.g., Atlantic Meridional Overturning Circulation fluctuations) and short-term climate modes like El Niño-Southern Oscillation, contribute to interannual and decadal salinity fluctuations but do not explain the directional, basin-scale trends observed over 50+ years.[163] For instance, decomposition analyses of upper-ocean salinity changes separate surface flux perturbations (e.g., from evaporation-precipitation imbalances) from interior redistribution, revealing that flux-driven components align with anthropogenic signals exceeding natural internal variability.[168] Empirical reconstructions, adjusted for sampling biases, confirm that pre-industrial baselines lacked comparable amplification, underscoring a departure from natural Holocene variability.[163]Scientific debates persist regarding the exact partitioning of causes, particularly the role of anthropogenic aerosols in modulating precipitation patterns and potentially offsetting greenhouse gas effects in some regions, as well as uncertainties in pre-2000 observations due to sparse coverage.[169] Critics of strong attribution argue that model-predicted sensitivities to radiative forcing may overestimate hydrological intensification, with some studies highlighting discrepancies between simulated and observed rates in the Southern Ocean, where natural upwelling and sea ice dynamics complicate isolation of human signals.[169] Nonetheless, detection analyses across multiple models robustly reject natural-only explanations, with anthropogenic forcing deemed necessary to fit the data at high confidence levels (>95%).[166] In coastal and estuarine systems, debates intensify over direct anthropogenic inputs like irrigation return flows and desalinationbrine discharge versus climate-mediated sea-level rise, with empirical data showing localized salinization rates up to 0.5 psu per decade in anthropogenically stressed areas outpacing open-ocean trends.[118][170]