Fact-checked by Grok 2 weeks ago

Adjacent-channel interference

Adjacent-channel interference (ACI) is a type of radio frequency interference in wireless communication systems where signals from adjacent frequency channels leak into and degrade the reception of the desired signal, primarily due to imperfections in transmitter filtering and receiver selectivity.^[1]^[2] This interference arises mainly from out-of-band emissions (OOBE) produced by transmitters, where power leaks into neighboring channels because of non-ideal bandpass filters and amplifier nonlinearities, as well as from receivers that fail to adequately suppress strong adjacent signals, leading to desensitization.^[1]^[3] In systems like cognitive radio networks or 5G radio access networks, ACI can occur between coexisting services, such as land-earth stations in motion operating at 27.5–29.5 GHz and 5G base stations at 24.25–27.5 GHz, exacerbated by spectral overlap and off-axis emissions.^[3]^[2] The effects of ACI are significant in modern wireless environments, as it reduces the signal-to-noise ratio (SNR), thereby lowering data throughput, increasing error rates, and potentially interrupting service reliability in applications ranging from cellular networks to Wi-Fi and public safety communications.^[1] In dense deployments, such as urban 5G areas, ACI can necessitate separation distances of up to 35 km between interfering systems to keep interference below thresholds like -147 dBW/MHz, directly impacting network capacity and coverage.^[3] Mitigation strategies for ACI include the use of guardbands to separate frequency allocations, enhanced receiver designs with advanced filters like FBAR or MEMS for better selectivity, and dynamic spectrum access techniques such as cognitive radio or geolocation databases to avoid overlapping usage.^[1] Additionally, optimized channel assignment and power control algorithms, including centralized reformulation-linearization techniques or distributed greedy methods, can reduce ACI by up to approximately 41% in ad hoc networks compared to sequential fixing approaches by minimizing leakage impacts.^[2] Regulatory measures, such as FCC attenuation requirements for OOBE, further support coexistence by enforcing emission limits.^[1]

Fundamentals

Definition and Principles

Adjacent-channel interference (ACI) is a form of interference in radio frequency communications where unwanted signal power from a transmitter operating on an adjacent frequency channel enters the receiver's passband, degrading the quality of the desired signal due to inadequate spectral isolation. This phenomenon disrupts the intended reception by introducing extraneous energy that overlaps with the target channel's spectrum.^[4]^[5] ACI fundamentally arises in multi-channel systems where transmitted signals have finite bandwidths that can extend beyond their allocated channels, leading to spectral overlap with neighboring channels if separation is insufficient. To mitigate this, spectrum allocation employs channelization, dividing the radio frequency band into discrete channels separated by guard bands—unused frequency intervals that provide a buffer to prevent signal leakage and maintain isolation. The width of these channels and guard bands directly influences the susceptibility to ACI, as denser allocations with minimal spacing heighten the risk of overlap in practical deployments.^[6]^[7]^[8] The origins of ACI trace back to the early era of radio broadcasting in the 1920s and 1930s, when the explosive growth of AM stations—from fewer than 100 at the start of 1922 to over 500 by the end of the year—caused severe frequency congestion on shared wavelengths, resulting in heterodyning whistles and signal overlap from nearby channels. Regulatory efforts, such as the expansion of the broadcast band to 550-1500 kHz in November 1924 and the U.S. Federal Radio Commission's General Order 40 in 1928, which introduced class-based channels (clear, regional, local) with 10 kHz spacing, aimed to provide better isolation and curb such interference, though challenges persisted with imprecise frequency control. By the 1930s, high-power experiments like Cincinnati's WLW at 500 kW demonstrated ACI's reach, interfering with adjacent stations hundreds of miles away and leading to FCC power caps in 1939 to protect spectrum integrity. Over time, technological advancements in modulation and filtering evolved management of ACI from these foundational broadcasting hurdles.^[9]^[10]

Distinction from Other Interference Types

Adjacent-channel interference (ACI) is distinguished from other interference types in wireless systems by its specific association with signals in frequency channels immediately adjacent to the desired signal, typically due to imperfect filtering or spectral regrowth at channel edges. In contrast, co-channel interference (CCI) originates from signals occupying the identical frequency channel, often resulting from deliberate frequency reuse in multi-cell networks like cellular systems, where multiple transmitters share the same spectrum to maximize capacity. For instance, in 8-PSK modulated data communication over AWGN channels, CCI degrades performance through direct signal overlap and contention, while ACI arises from power leakage into neighboring bands, requiring separate signal-to-interference ratio analyses for mitigation.^[11]^[12] A practical example highlights this boundary: in FM radio broadcasting, where channels are spaced 200 kHz apart, ACI manifests as audible distortion from an adjacent station's signal if the receiver lacks sufficient selectivity, whereas CCI would involve two stations on the exact same frequency causing complete overlap and mutual disruption. Similarly, in Wi-Fi networks operating in the 2.4 GHz band, co-channel interference occurs among access points using the same non-overlapping channel (e.g., channels 1, 6, or 11), leading to increased medium access contention, while ACI affects overlapping adjacent channels like 1 and 2 due to partial spectral bleed.^[13]^[14] ACI further differs from crosstalk, which refers to unintended electromagnetic coupling between separate wired communication lines, such as in telephone cables, rather than frequency-selective issues in RF propagation environments. Unlike intermodulation interference, which generates spurious products at new frequencies (e.g., sums or differences) from nonlinear device interactions in mixers or amplifiers, ACI involves no such frequency conversion but direct encroachment from adjacent-channel emissions. Blocking interference, by comparison, results from strong out-of-band signals—often far removed from the desired channel—overloading the receiver's dynamic range and reducing overall sensitivity, in opposition to ACI's emphasis on adjacent-band rejection capabilities. These distinctions underscore ACI's unique reliance on channel spacing and receiver selectivity, such as the typical 200 kHz guard in FM systems, to maintain signal integrity.^[11]^[15]^[16]

Causes

Transmitter imperfections significantly contribute to adjacent-channel interference (ACI) by allowing unwanted signal energy to leak into neighboring frequency bands. Inadequate filtering at the transmitter output can lead to spectral regrowth, where nonlinear processing broadens the signal spectrum beyond the intended channel boundaries.^[17] This occurs primarily due to the limited selectivity of transmit filters, which fail to sufficiently suppress sidebands generated during modulation, resulting in elevated emissions in adjacent channels.^[18] A key source of such leakage is intermodulation distortion (IMD) within power amplifiers (PAs), which spreads energy into adjacent channels through nonlinear mixing of signal components. IMD arises when multiple frequency tones or modulated carriers interact in the PA, producing harmonic and intermodulation products that fall outside the main channel.^[19] In particular, nonlinear amplification exacerbates out-of-band (OOB) emissions by compressing the signal and introducing amplitude (AM/AM) and phase (AM/PM) distortions, which regenerate spectral components in nearby bands.^[17] These effects are pronounced in high-power transmitters, where operating near saturation to maximize efficiency amplifies the distortion.^[19] The Adjacent Channel Leakage Ratio (ACLR) serves as a primary metric to quantify these transmitter-induced emissions, measuring the extent of power leakage relative to the main channel. ACLR is defined as the ratio of the filtered mean power in the assigned channel to the filtered mean power in the adjacent channel, expressed in decibels.^[20] Mathematically,

\text{ACLR (dB)} = 10 \log_{10} \left( \frac{P_{\text{channel}}}{P_{\text{adjacent}}} \right),

where P_{\text{channel}} is the integrated power over the main channel bandwidth, and P_{\text{adjacent}} is the integrated power over an equivalent bandwidth in the adjacent channel.^[20] This ratio is derived from the power spectral density (PSD) by first applying square filters with bandwidth equal to the channel bandwidth for both the main and adjacent channels, then integrating the filtered PSD over the respective bandwidths (e.g., 5 MHz for a 5 MHz channel).^[20] The filtering step accounts for the spectral shaping in standards like 3GPP, ensuring the measurement reflects practical interference levels after propagation through receiver filters.^[21] In digital modulation schemes such as orthogonal frequency-division multiplexing (OFDM) used in LTE, nonlinear PA distortion is particularly detrimental, as the high peak-to-average power ratio (PAPR) of OFDM signals drives the amplifier into nonlinear regions, necessitating stricter ACLR requirements to limit OOB emissions. For LTE base stations, 3GPP specifies a minimum ACLR of 45 dB for the first adjacent channel in paired spectrum, reflecting the need to protect coexisting systems like UMTS. This threshold ensures that IMD products do not degrade adjacent channel performance beyond acceptable levels.^[22] In modern 5G NR deployments, the challenge intensifies with channel bandwidths expanding to 100 MHz in sub-6 GHz bands, increasing the volume of potential leaked energy and amplifying ACI risks from spectral regrowth across wider spectra.^[23] In 5G NR, ACLR requirements are specified in 3GPP TS 38.104 and vary by subcarrier spacing and band, typically 45 dB for the first adjacent channel in FR1 (sub-6 GHz), with some bands requiring up to 50 dB as of Release 18 (2024).^[24] The broader integration bandwidths demand more precise PA linearization to prevent heightened interference in densely packed frequency allocations. Receiver vulnerabilities to adjacent-channel interference (ACI) primarily arise from inadequate filtering and overload in the front-end circuitry. Poor adjacent channel selectivity often stems from insufficient roll-off in the receiver's bandpass filters, allowing signals from nearby frequencies to partially pass through and degrade the desired signal.^[25] Front-end overload occurs when strong adjacent signals exceed the linear range of the low-noise amplifier (LNA) or mixer, causing desensitization or intermodulation products that mask the wanted signal.^[26] A key metric quantifying these vulnerabilities is Adjacent Channel Selectivity (ACS), which measures the receiver's ability to maintain performance for a desired signal in the presence of an adjacent-channel interferer. ACS is defined as the difference in power levels between the interferer and the wanted signal at the point of performance degradation, expressed in decibels:

\text{ACS (dB)} = P_{\text{interferer}} - P_{\text{wanted}}

Here, the measurement setup typically involves setting the wanted signal at the reference sensitivity level plus 3 dB, applying a continuous-wave (CW) or modulated interferer offset by the channel bandwidth (e.g., ±5 MHz for GSM), and increasing the interferer power until the receiver's output degrades by 3 dB relative to the baseline, with ACS expressed as the difference between interferer and wanted signal powers at that point.^[26] This setup highlights how filter characteristics and dynamic range directly influence ACS values, often targeting 60-70 dB in professional standards.^[25] In superheterodyne receivers, additional susceptibility comes from inadequate image frequency rejection, where signals at the image frequency (f_image = f_LO + (f_LO - f_wanted), separated by twice the intermediate frequency) fold into the IF band and interfere if not suppressed by the RF front-end filter.^[27] Poor IF filtering exacerbates this by allowing adjacent signals to leak through the IF stage due to gradual roll-off beyond the channel bandwidth, resulting in co-channel-like interference at the demodulator.^[28] Modern receivers, such as those in WiFi 6 (IEEE 802.11ax) systems, face heightened ACI challenges in dense environments with overlapping 20/40/80 MHz channels, where limited spectrum availability and high device density demand enhanced selectivity to avoid performance degradation from neighboring access points.

Effects

Impact on Signal Quality

Adjacent-channel interference (ACI) degrades the received signal by introducing unwanted power from neighboring channels, which elevates the noise floor in the desired channel and reduces the signal-to-interference ratio (SIR). This interference acts as additional noise, impairing the demodulation process and leading to higher bit error rates (BER) in digital communications. For instance, in systems employing quadrature amplitude modulation (QAM), ACI causes constellation errors by shifting and distorting symbol points, making correct detection more challenging. In digital packet-based networks, the elevated BER due to ACI results in throughput loss through increased packet error rates and retransmissions. Quantitative studies show that under ACI, BER can rise significantly; for example, in 8-QAM modulation over Rayleigh fading channels, ACI degrades performance more severely than in additive white Gaussian noise (AWGN) channels, with error rates increasing as SIR decreases. In analog systems such as frequency modulation (FM) radio, ACI manifests as audible distortion, including crosstalk and impulsive noise, due to the nonlinear response of FM demodulators. Low-level ACI can trigger threshold effects, where the interference suddenly becomes dominant, generating bursts of threshold noise that render the audio unintelligible despite adequate signal strength. These effects are particularly pronounced when the interfering carrier is close to the desired frequency, reducing the overall signal quality below acceptable levels for broadcast reception.^[29]^[29] For modern narrowband Internet of Things (NB-IoT) devices, which operate in 180 kHz channels, ACI from adjacent LTE carriers severely impacts signal quality by lowering the signal-to-interference-plus-noise ratio (SINR) and increasing block error rates (BLER), akin to BER. Field measurements indicate SINR drops as low as -3.4 dB in challenging scenarios, with BLER exceeding 10% in some interfered cases and connectivity failures in coverage-challenged areas, highlighting the vulnerability of these low-power, narrowband systems to spectral leakage from coexisting wideband signals.^[30]^[30]

System-Level Consequences

Adjacent-channel interference (ACI) significantly reduces the overall capacity of cellular networks by imposing limitations on frequency reuse schemes. In traditional cellular systems, ACI necessitates greater separation between co-located channels to minimize spillover, which constrains the number of reusable frequencies and thereby lowers spectral efficiency. For instance, in dense urban environments, this interference can significantly reduce the effective capacity, as operators must allocate wider guard bands or reduce transmit power to avoid mutual disruption.^[31]^[32] In broadcasting services, ACI leads to widespread service disruptions, particularly in analog FM and TV systems where weak signals from adjacent channels can cause audible distortion or visual artifacts, interrupting reception over large areas. Modern urban 5G deployments exacerbate this issue with dense small cell networks, where ACI from overlapping carrier frequencies can degrade coverage reliability in high-traffic zones, leading to inconsistent connectivity for users.^[33]^[34]^[35] Operationally, ACI in mobile networks contributes to elevated rates of dropped calls and reduced data throughput, thereby straining network resources and user satisfaction. Economically, non-compliance with spectrum regulations on ACI limits can result in substantial fines, impacting operators' budgets and deployment timelines. In unlicensed bands like the 2.4 GHz WiFi spectrum, channel overcrowding amplifies ACI, as overlapping signals from nearby access points cause packet collisions and throughput degradation of over 50% in congested environments, limiting viable connections in shared spaces such as apartments or offices.^[36]^[37]^[38]

Measurement and Analysis

Key Performance Metrics

Adjacent channel interference (ACI) is quantified through several key performance metrics that assess the extent of power leakage from a primary channel into neighboring frequencies or the receiver's ability to suppress such interference. The primary transmitter-side metric is the Adjacent Channel Power Ratio (ACPR), also known as the Adjacent Channel Leakage Ratio (ACLR) in standards like 3GPP. ACPR measures the ratio of the average power in the main transmit channel to the average power in an adjacent channel, typically expressed in decibels (dB). The formula is given by:

\text{ACPR} = 10 \log_{10} \left( \frac{P_{\text{main}}}{P_{\text{adj}}} \right)

where P_{\text{main}} is the filtered mean power centered on the assigned channel frequency, and P_{\text{adj}} is the filtered mean power centered on the adjacent channel frequency.^[39] Measurements involve specific offset frequencies from the carrier (e.g., ±5 MHz for the first adjacent channel in LTE systems) and integration bandwidths tailored to the technology, such as 4.515 MHz for offsets in 3GPP LTE specifications to align with GSM-like channel widths or up to the channel bandwidth for 5G NR. These parameters ensure consistent evaluation of leakage across the spectrum mask. Another core metric, particularly for receiver performance, is the Adjacent Channel Rejection Ratio (ACRR), which evaluates the receiver's selectivity by comparing the desired signal gain to the gain from an adjacent-channel interferer. ACRR is defined as the ratio of the root-raised cosine (RRC) weighted gain per carrier in the passband to the RRC weighted gain per carrier in the immediately adjacent band, often measured in dB.^[40] In standards like ETSI TR 102 914 for cognitive radio systems, ACRR quantifies how effectively a receiver attenuates ACI while preserving the primary signal, with typical requirements exceeding 30 dB depending on modulation and bandwidth. These metrics vary significantly by wireless technology to reflect evolving spectral efficiency demands. For instance, in GSM systems, ACLR requirements are set at 30 dB for the first adjacent channel to protect legacy narrowband operations, as specified in 3GPP TS 45.005 for base station emissions.^[41] In contrast, 3GPP LTE mandates stricter ACLR limits of -45 dBc for base stations in most bands, with integration over the full adjacent channel bandwidth to minimize interference in wider carrier scenarios. For 5G NR, requirements are even more stringent, often at -45 dBc or better (e.g., -50 dBc for certain sub-6 GHz bands), as outlined in TS 38.104, to support higher densities and massive MIMO deployments. Preliminary concepts for 6G, as explored in ongoing IEEE and 3GPP studies, emphasize enhanced ACI metrics to address terahertz bands and integrated sensing-communications (ISAC). These include tighter ACLR targets potentially below -50 dBc with adaptive offsets for dynamic spectrum sharing, alongside new receiver metrics like interference cancellation ratios in multi-user environments, though specific values remain under development in ongoing 3GPP studies for future releases.

Testing Procedures

Laboratory testing for adjacent-channel interference (ACI) primarily involves controlled environments to quantify transmitter and receiver performance using standardized metrics such as adjacent channel leakage ratio (ACLR) and adjacent channel selectivity (ACS). For ACLR measurement, a spectrum analyzer is employed to assess the ratio of the filtered mean power in the assigned channel to that in the adjacent channel. The procedure begins with calibration of the spectrum analyzer to ensure accurate power readings, followed by applying a test signal (e.g., Test Model 1 for W-CDMA) through a root-raised cosine (RRC) filter with a 3.84 MHz bandwidth. The analyzer's filter is centered on the assigned channel and then the adjacent channel at a nominal offset (e.g., 5 MHz), integrating power over the measurement bandwidth if the resolution bandwidth is smaller; requirements typically mandate ACLR ≥ 45 dB at 5 MHz offset.^[42]^[39] ACS testing evaluates receiver resilience by simulating interference, using a signal generator to produce a wanted signal at reference sensitivity plus an offset (e.g., +14 dB for 5-10 MHz bandwidths) alongside an adjacent-channel interferer (e.g., 5 MHz bandwidth W-CDMA signal at reference sensitivity +45.5 dB). Calibration involves verifying generator output levels and analyzer settings for precise power application, with throughput measured to ensure it reaches at least 95% of maximum under the interferer; typical ACS thresholds are ≥33 dB for 5-10 MHz channels.^[42]^[39] In field settings for cellular networks, drive tests map ACI by equipping vehicles with spectrum analyzers or mobile test equipment to collect signal data while traversing coverage areas, identifying interference sources through geolocated measurements of adjacent channel power leakage. The setup includes GPS integration for mapping, antenna calibration for consistent gain, and real-time logging of metrics like signal-to-interference ratios during active network operation, often revealing ACI from overlapping cell deployments.^[43] For WiFi ACI assessment, protocol analyzers perform spectrum scans to detect channel overlap and interference, starting with device calibration against known signals, followed by passive monitoring of utilization and signal strengths to pinpoint adjacent-channel sources affecting throughput.^[44] Standardized procedures from ETSI and 3GPP outline step-by-step lab setups for mobile systems, including equipment calibration, signal application, and performance verification per TS 138 101-5 and TS 25.141. In broadcasting, FCC methods under 47 CFR §15.117 specify receiver testing for ACI, involving antenna-height measurements (e.g., 1.5 meters) and power spectral density assessments (e.g., ≤ -40 dBm over 10 MHz) to ensure adjacent-channel rejection without excessive interference.^[39]^[42]^[45] Modern tools like software-defined radios (SDRs) enable real-time ACI monitoring by capturing wideband IQ data for immediate analysis, with calibration via software-defined filters to detect low-level adjacent signals in dynamic environments such as 5G networks. SDRs facilitate continuous spectrum sweeps (e.g., 0-40 GHz) and interference localization, offering a cost-effective alternative to traditional hardware for both lab validation and field deployment.^[46]^[47]

Mitigation

Engineering Solutions

Engineering solutions for adjacent-channel interference (ACI) primarily involve hardware and software techniques that enhance signal isolation and linearity at the transmitter and receiver levels. Advanced filtering methods, such as surface acoustic wave (SAW) filters, provide sharp roll-off characteristics to suppress unwanted signals in adjacent channels while maintaining low insertion loss. These filters are particularly effective in RF front-ends, where they improve adjacent channel rejection by attenuating out-of-band emissions without significantly impacting the desired signal bandwidth.^[48] In transmitters, digital pre-distortion (DPD) linearizes power amplifiers to counteract nonlinear distortions that cause spectral regrowth and subsequent ACI. By modeling the amplifier's memory effects using techniques like the generalized memory polynomial and applying inverse predistortion to the input signal, DPD reduces intermodulation products, ensuring compliance with spectral emission masks in systems like 5G base stations. For instance, DPD can significantly suppress adjacent channel power, allowing efficient operation near saturation while minimizing interference leakage. Power amplifier linearization through predistortion also addresses amplitude and phase distortions, preventing bandwidth expansion from the original signal span to multiple times that width due to higher-order nonlinearities.^[49] Receiver architectures, such as zero-intermediate frequency (zero-IF) designs, improve selectivity by directly downconverting the RF signal to baseband, where lowpass filters in the in-phase and quadrature paths effectively remove adjacent channel components. This eliminates the need for intermediate frequency stages, enabling programmable active filters that tune rejection from hundreds of kHz to MHz, thus enhancing ACI mitigation in wideband applications.^[50] At the system level, adaptive modulation and coding schemes dynamically adjust constellation sizes and error correction based on detected interference levels, countering ACI by lowering modulation order in affected channels to maintain bit error rates below thresholds. In multiple-input multiple-output (MIMO) systems, beamforming provides spatial isolation by directing beams toward intended users, nulling interference from adjacent channels through phased array processing that boosts signal-to-interference-plus-noise ratio. For example, hybrid analog-digital beamforming adaptively filters interference before analog-to-digital conversion, reducing dynamic range requirements.^[51] In Wi-Fi networks, dynamic frequency selection (DFS) optimizes channel allocation in the 5 GHz band by scanning for and avoiding occupied adjacent channels, including radar signals, to minimize overlap and contention that exacerbate ACI. This mechanism switches access points within 200 ms of detection, enforcing a 30-minute non-occupancy period to ensure clean spectrum reuse.^[14] For 5G massive MIMO and mmWave systems, where wide bandwidths amplify ACI through beam squint—frequency-dependent beam direction shifts that misalign signals across subcarriers—mitigation relies on frequency-invariant beamforming. Techniques like mean channel covariance matrix-based phase shift design for reconfigurable intelligent surfaces compensate for squint, preserving beam alignment and limiting performance losses to under 1 bps/Hz even at 500 MHz bandwidths.^[52] These approaches exploit subcarrier correlations to maintain spatial isolation, addressing ACI exacerbated by large antenna arrays and high frequencies. Recent advancements as of 2025 include machine learning-driven interference cancellation techniques in 5G-Advanced systems to further enhance ACI mitigation.^[53]

Regulatory Approaches

Regulatory bodies such as the Federal Communications Commission (FCC) in the United States and the International Telecommunication Union (ITU) establish guidelines on channel spacing and emission limits to mitigate adjacent-channel interference (ACI). For FM broadcasting, the FCC mandates a standard channel spacing of 200 kHz to separate stations and reduce overlap between signals. In mobile networks like LTE, channel bandwidths typically start at 5 MHz, with ITU recommendations ensuring adequate guard bands to limit emissions into adjacent channels.^[54] Emission masks further enforce these protections; for instance, FCC rules under 47 CFR § 73.317 require FM transmitters to attenuate emissions between 120 kHz and 240 kHz from the carrier by at least 25 dB, helping to limit spillover into the first adjacent channel (200 kHz spacing).^[55] Spectrum planning procedures involve coordinated frequency assignments to avoid adjacent-channel usage where possible. The FCC requires broadcasters to adhere to minimum distance separations based on station class and power, calculated to minimize ACI, with frequency coordinators reviewing applications for compliance.^[56] Coordination zones around existing stations ensure new assignments do not encroach on protected areas, facilitating interference-free operations through technical studies and international agreements under ITU auspices. A notable development in U.S. FM regulation occurred following a 2003 FCC-commissioned study by MITRE Corporation, which found minimal third-adjacent channel interference from low-power FM (LPFM) stations to full-service FM, paving the way for policy adjustments to expand LPFM licensing without such protections.^[57] This led to the eventual repeal of third-adjacent channel separation requirements via the Local Community Radio Act of 2010, allowing more stations while relying on emission limits and complaint-based resolutions. International variations highlight differing approaches to ACI management. In Europe, many countries adopt a 100 kHz channel spacing for FM broadcasting—half the U.S. standard—necessitating stricter emission controls and planning to accommodate denser station allocations without excessive interference.^[58] ITU recommendations support these regional differences, promoting harmonized yet adaptable standards across ITU-R regions. Recent updates in spectrum policy for 5G emphasize ACI minimization during auctions. The FCC's C-band auction (Auction 107) in 2021 incorporated interference protections for incumbent satellite users, including dynamic power limits and exclusion zones to safeguard adjacent bands. Similarly, ITU-R reports on IMT-2020 (5G) advocate for advanced emission templates and coexistence studies in spectrum auctions to ensure minimal ACI in shared mid-band allocations like 3.3–4.2 GHz.^[8]

References

[1]
[PDF] INTERFERENCE AND DYNAMIC SPECTRUM ACCESS ...
Jul 31, 2007 · Where appropriate, guardbands should continue to be used as a tool to reduce the effects of out- of-band emissions (OOBE) and adjacent channel ...
[2]
[PDF] On co-channel and adjacent channel interference mitigation in ...
The second type is adja- cent channel interference (ACI), which is in the form of power leakage from adjacent channels. ACI is mainly due to imperfect design of ...Missing: effects | Show results with:effects
[3]
Evaluation of adjacent channel interference from land-earth station ...
Jun 25, 2021 · Adjacent channel interference (ACI). ACI results from signals that are adjacent in frequency to the desired signal and is due to imperfect ...Missing: mitigation | Show results with:mitigation
[4]
Understanding adjacent channel leakage ratio (ACLR)
These channels are often adjacent in frequency to other channels of the same service or to other spectrum users.Aclr In Wireless... · Leakage And Adjacent Channel... · Summary Of Aclr
[5]
[PDF] Interference calculation methods - ITU
adjacent channel, which means that a relaxed protection against interference from this first adjacent channel was assumed. Page 14. 12. Rep. ITU-R BT.2019-1.
[6]
[PDF] RECOMMENDATION ITU-R F.595-8 - Radio-frequency channel ...
guardbands are the most suitable choice for sub-band allocations for such low capacity utilizations, however, when more band is required, the adjacent channels ...Missing: spectrum | Show results with:spectrum
[7]
[PDF] Setting and Maintaining Boundaries in Wireless Spectrum Access
Guardbands are designed to insulate transmissions on adjacent fre- quencies from mutual interference. As more devices in a given area are packed into orthogonal ...
[8]
[PDF] Report ITU-R SM.2523-0 (06/2023) - Assessment of spectrum ...
The frequency factor can be measured by frequency, bandwidth and adjacent channel interference. 4.1.1.6 Use. Potential uses of a band depend on regulatory ...
[9]
Building the Broadcast Band - Early Radio History
The above chart is a general overview of the evolution of the broadcast band, and selected wavelength and frequency allocations from 1921 to 1928.
[10]
For a Brief Time in the 1930s, Radio Station WLW in Ohio Became ...
(Although WLW had its own cleared frequency, its signal could still cause problems for closely adjacent channels of stations located hundreds of miles away.
[11]
Adjacent-Channel Interference - an overview | ScienceDirect Topics
Adjacent channel interference (ACI) is defined as interference caused by signals that are adjacent in frequency to a desired signal, primarily resulting ...
[12]
Analysis and mitigation of adjacent and co-channel interference on ...
The co-channel interference occurs due to the same frequency is used by the two different radio transmitters leads to a crosstalk. This crosstalk is nothing ...
[13]
[PDF] fm broadcast channel frequency spacing
The adjacent channel stations were located as effi- ciently as possible within the equilateral cochannel triangles, using the assignment techniques developed ...
[14]
Channel Planning Best Practices for Better Wi-Fi - Ekahau
Apr 1, 2022 · This type of interference is called Adjacent Channel Interference (ACI). 2.4GHz Channel Overlap. Source: Ekahau ECSE Design Course. Adjacent ...
[15]
[PDF] Introduction to Interference Resolution, Enforcement and Radio ...
Jun 10, 2014 · the co-channel and adjacent channel interference ... Both blocking and intermodulation interference are associated with the dynamic range of a ...
[16]
Blocking and Interference Rejection - Circuit Cellar
Oct 1, 2021 · Typical receivers tolerate perturbances in the adjacent channel with power levels significantly higher than the received level, meaning that the ...
[17]
Effects of AM/AM and AM/PM Distortion on Spectral Regrowth in ...
Nov 1, 2002 · A figure of merit known as adjacent channel leakage ratio (ACLR) quantifies spectral regrowth. In the 3GPP standard, it is defined as the ratio ...Spectral Regrowth In 3gpp... · Amplifier Am/am And Am/pm... · Related Resources<|separator|>
[18]
[PDF] SM.2021 - Production and mitigation of intermodulation ... - ITU
Type 3: Inter transmitter intermodulation: where one or more transmitters on a site intermodulate, either within the transmitters themselves or within a non- ...
[19]
https://ieeexplore.ieee.org/document/5158745
[20]
[PDF] TS 136 104 - V8.10.0 - LTE - ETSI
The out-of-band emissions requirement for the BS transmitter is specified both in terms of Adjacent Channel Leakage power Ratio (ACLR) and Operating band ...
[21]
https://www.3gpp.org/ftp/Specs/html-info/36104.htm
[22]
[PDF] TS 136 141 - V8.4.0 - LTE - ETSI
This corresponds to a Test equipment ACLR which is 10.2 dB bettter than the BS ACS e) This leads to the following Test equipment ACLR requirements for the ...
[23]
https://www.3gpp.org/ftp/Specs/html-info/38104.htm
[24]
Adjacent Channel Selectivity, ACS. - Electronics Notes
Adjacent channel selectivity, ACS, defines how well a radio receiver rejects unwanted signals on nearby frequencies. · Radio receiver filter specifications.
[25]
[PDF] AN-1570 APPLICATION NOTE - Analog Devices
Adjacent channel saturation is similar to the adjacent channel selectivity, except that the power level of the wanted signal is 43 dB above the sensitivity ...<|control11|><|separator|>
[26]
Superheterodyne Receiver: Image Response - Electronics Notes
It does not need to reject signals on adjacent channels, but instead it needs to reject signals on the image frequency. These will be separated from the ...
[27]
Adjacent-Channel Rejection - an overview | ScienceDirect Topics
The interleaving process ensures that, if a signal is degraded for a short period of time, sequential data is not lost. ... 1.3 Sensitivity measurements.
[28]
https://www.sciencedirect.com/topics/engineering/adjacent-channel-rejection
[29]
None
### Summary of Adjacent Channel Interference in FM Systems (Rec. ITU-R SF.766)
[30]
[PDF] PERFORMANCE ANALYSIS OF IOT WIRELESS CELLULAR ... - RUN
adjacent channel interference, thermal noise, and other factors. ... of the relation between distance and the metrics that regard signal quality for NB-IoT,.
[31]
Frequency reuse in limited spectrum networks - Ericsson
On one hand, the risk of interference between neighboring links is much higher in a Reuse 1 network when compared to a Reuse 2 network, but, on the other hand, ...
[32]
Cellular network configuration with co-channel and adjacent ...
By keeping the frequency separation between each channel in a given cell as large as possible, the adjacent-channel interference may be reduced considerably. ...
[33]
What You Need to Know About Adjacent Channel Interference
Jun 12, 2013 · Adjacent Channel Interference between DTV signals may become critical after the FCC repacks the remaining UHF TV spectrum.
[34]
Radio Broadcasting | Encyclopedia MDPI
Nov 30, 2022 · In response to the growing popularity of FM stereo radio stations in the late 1980s ... adjacent channel interference. The larger bandwidth allows ...<|separator|>
[35]
Evaluation of adjacent channel interference from land-earth station ...
Research article. Evaluation of adjacent channel interference from land-earth station in motion to 5G radio access network in the Ka-frequency band.
[36]
Mitigating interference and signal disruptions in wireless ...
Increased co-channel and adjacent channel interference results in dropped calls, slow data throughput, and signal latency. Interference also affects non- ...<|separator|>
[37]
[PDF] Interference Limits Policy - Federal Communications Commission
Receiving systems that cannot reject interfering signals transmitted outside their licensed frequencies can preclude or constrain new allocations in adjacent ...
[38]
WiFi Channel Overlap: How to Identify and Fix Issues - NetAlly
With adjacent channel interference (overlapping channels): Devices can't properly detect transmissions on partially overlapping channels. They incorrectly think ...
[39]
[PDF] ETSI TS 138 101-5 V17.4.0 (2023-07)
Adjacent Channel Leakage power Ratio (ACLR) is the ratio of the filtered mean power centred on the assigned channel frequency to the filtered mean power centred ...
[40]
[PDF] ETSI TR 102 914 V1.1.1 (2009-01)
Adjacent Channel Rejection Ratio (ACRR) is the ratio of the RRC weighted gain per carrier in the passband to the RRC weighted gain per carrier immediately ...
[41]
[PDF] Agilent Designing and Testing 3GPP W-CDMA Base Transceiver ...
Oct 1, 2009 · ... adjacent channel leakage power ratio (ACLR), adjacent channel selectivity (ACS), and adjacent channel interference ratio (ACIR). ACLR is a ...
[42]
Identifying and Solving GSM Radio Interference - Keysight
Learn how to Identify GSM 850 radio interference in public safety communications and solve adjacent channel interference.
[43]
WiFi Network Testing: All Wireless Solutions - NetAlly
Rating 4.3 (13) Plan, map, test and validate your wireless network with the wireless network testers from NetAlly. Easy to use and guaranteed results in minutes. NetAlly.
[44]
[PDF] Federal Communications Commission FCC 22-29 Before the ...
Apr 21, 2022 · requirements and measurement methods for cable TV receivers for adjacent channel interference, image channel interference, direct pickup ...
[45]
Software Defined Radio Use Case for Spectrum Monitoring
Jan 12, 2022 · SDRs are used in spectrum monitoring for testing networks, protecting aviation, monitoring illegal broadcasts, and protecting military assets, ...
[46]
Low-Cost Sensor Based on SDR Platforms for TETRA Signals ...
May 2, 2021 · A low-cost alternative to deploying a spectrum monitoring station was recently offered by Software Defined Radio (SDR) technology. The ...
[47]
High-Selectivity SAW Filters for Enhanced RF Performance - Abracon
Designed for sharp roll-off characteristics, these filters effectively mitigate adjacent channel interference while maintaining low insertion loss. Housed ...
[48]
Digital Predistortion for RF Communications: From Equations to ...
This article covers the mathematical fundamentals of digital predistortion (DPD) and how it is implemented in a transceiver's microprocessor and hardware.
[49]
Direct Conversion (Zero-IF) Receiver | Wireless Pi
Mar 20, 2023 · Since a zero-IF architecture directly reduces the frequencies of interest to baseband, the analog circuits are designed at the lowest frequency ...
[50]
A Systematic Review of Interference Mitigation Techniques in Current and Future UAV-Assisted Wireless Networks
**Summary of Adaptive Modulation and Beamforming for Interference Mitigation (Including ACI):**
[51]
[PDF] Report ITU-R M.2529-0 (09/2023) - Adjacent band compatibility ...
For study purpose channel bandwidth 5,. 10 MHz will be considered for IMT, however other channel bandwidth values may be also considered. Page 8. 6. Rep. ITU-R ...
[52]
73.317 FM transmission system requirements. - Title 47 - eCFR
(c) Any emission appearing on a frequency removed from the carrier by more than 240 kHz and up to and including 600 kHz must be attenuated at least 35 dB below ...
[53]
Coordination | Federal Communications Commission
Apr 9, 2024 · Frequency coordination is the technical exchange of planned spectrum or radio frequency use conducted by authorized operators when designing or operating a ...
[54]
[PDF] Report to Congress on the Low Power FM Interference Testing ...
Feb 19, 2004 · The Mitre Report states that, even in the worst case, no third-adjacent channel interference between an LPFM station and an existing full- ...
[55]
FM broadcast band - Wikipedia
Deviation is typically limited to 150 kHz total (±75 kHz) in order to prevent adjacent-channel interference on the band. Stations in the U.S. may go up to ...