Fact-checked by Grok 2 weeks ago

Flyback converter

A flyback converter is an isolated DC-DC switching power supply topology that utilizes a transformer to store energy from the input source during one phase of operation and transfer it to the output during another, enabling step-up, step-down, or inverting voltage conversion with galvanic isolation between input and output.^[1]^[2] It is particularly suited for low- to medium-power applications, typically up to 100 W, where simplicity and cost-effectiveness are prioritized over higher power handling.^[3]^[2] The basic operation of a flyback converter relies on a coupled inductor (transformer) with primary and secondary windings phased 180° out of phase, controlled by a switching element such as a MOSFET.^[1]^[2] When the switch is closed (on-state), current flows through the primary winding, storing energy in the transformer's magnetic core while the secondary winding's diode remains reverse-biased, preventing energy transfer to the output; the load is supplied by the output capacitor during this period.^[3] When the switch opens (off-state), the collapsing magnetic field induces voltage in the secondary winding, forward-biasing the diode to deliver stored energy to the output, charging the capacitor and powering the load.^[1] This energy storage and release mechanism distinguishes the flyback from non-isolated buck-boost converters, as the transformer provides both energy storage and electrical isolation.^[2] Flyback converters can operate in continuous conduction mode (CCM), where the secondary current never reaches zero before the next cycle, or discontinuous conduction mode (DCM), where it does, with a critical conduction mode (CRM) at the boundary.^[1] In CCM, the converter exhibits lower output ripple and higher efficiency at full load but requires careful design to manage dynamic behavior; DCM simplifies control and reduces diode reverse recovery losses, improving light-load efficiency, though it may increase ripple at higher powers.^[3] Key components include the transformer, primary-side switch, secondary rectifier diode, output capacitor, and a feedback controller (e.g., PWM IC) to regulate output voltage via optocoupler or other sensing methods.^[1] Compared to other isolated topologies like the forward converter, the flyback offers advantages in simplicity, with fewer components (typically five versus eight) and a smaller, cheaper transformer that does not require a reset winding, making it ideal for compact designs.^[2] However, it is less efficient at higher powers due to increased leakage inductance losses and core saturation risks, and it provides poorer transient response in some configurations.^[2] Common applications encompass auxiliary power supplies, battery chargers, LED drivers, and isolated adapters in consumer electronics, medical devices, and automotive systems, where multiple outputs of varying polarities can be derived from additional windings.^[3]^[2]

Fundamentals

Basic Principle

The flyback converter functions as an isolated DC-DC converter topology derived from the buck-boost converter, utilizing a transformer to store energy in its magnetizing inductance and provide galvanic isolation between input and output.^[4] Unlike the non-isolated buck-boost converter, which relies on a single inductor for energy storage, the flyback separates the storage and transfer phases across primary and secondary windings of the transformer, enabling voltage step-up or step-down while preventing direct electrical connection between circuits.^[4] The basic circuit configuration includes an input DC voltage source connected to the primary winding of the transformer via a controlled switch, such as a MOSFET. The secondary winding connects to the output through a rectifier diode and a filter capacitor in parallel with the load resistor. The windings are coupled with opposite polarity (indicated by dots in schematic representations) to ensure that energy transfer occurs only during the switch-off period.^[5] In operation, during the switch-on phase, the MOSFET closes, applying the input voltage V_{in} across the primary winding. This causes the magnetizing current to ramp up linearly through the magnetizing inductance L_m, storing energy in the magnetic field according to E = \frac{1}{2} L_m I^2, where I is the increasing current. The induced voltage in the secondary winding reverse-biases the diode, isolating the output and preventing discharge to the load.^[5] When the switch opens, the magnetizing current interrupts, and the collapsing magnetic field induces a voltage in the secondary winding that forward-biases the diode. This allows the stored energy to transfer to the output capacitor and load, with the secondary current ramping down until it reaches zero in discontinuous mode.^[6] The transformer's turns ratio n = N_p / N_s (primary to secondary turns) plays a critical role by scaling the transferred voltage and current, enabling the topology to achieve both step-up and step-down conversion ratios while maintaining isolation.^[6] In ideal discontinuous conduction mode, where the magnetizing current returns to zero before the next switching cycle begins, the voltage conversion ratio can be derived from power balance. The peak magnetizing current is I_{pk} = \frac{V_{in} D}{L_m f_{sw}}, where D is the duty cycle and f_{sw} is the switching frequency. The energy stored per cycle is \frac{1}{2} L_m I_{pk}^2, and the average output power equals the input power, \frac{V_{out}^2}{R_{load}}. Simplifying yields the conversion ratio \frac{V_{out}}{V_{in}} = D \sqrt{\frac{R_{load}}{2 L_m f_{sw}}}.^[5]^[7]

Historical Development

The flyback converter, originally known as the ringing choke converter, was developed in the 1930s and 1940s primarily for generating high voltages in cathode ray tube (CRT) deflection circuits within early vacuum tube radios and television sets.^[8] This design leveraged the transformer's ability to store and release energy during flyback periods to drive horizontal scanning in CRT displays, providing a cost-effective solution for the burgeoning consumer electronics market.^[8] By the 1950s, refinements in the topology supported widespread commercialization of televisions, establishing its reputation for simplicity and reliability in low-power, isolated applications.^[8] In the 1970s and 1980s, advancements in semiconductor technology, particularly the introduction of power MOSFETs, enabled the transition from vacuum tube-based implementations to solid-state switching, expanding the flyback converter's role beyond deflection to general-purpose DC-DC power supplies.^[9] A pivotal milestone occurred in 1978 when Frederick Rod Holt designed a 38 W multi-output flyback switching power supply for the Apple II personal computer, marking one of the earliest adoptions in computing and demonstrating its efficiency advantages over linear supplies.^[10] Throughout the 1980s, this topology gained traction in PC power supplies from manufacturers like IBM and Hewlett-Packard, driven by needs for compact, fanless designs with improved power density.^[9] In the 1990s, primary-side regulation techniques were introduced, allowing output voltage control without optocouplers or secondary-side feedback, thereby reducing component count and cost in low-power adapters.^[11] The 2000s saw flyback converters evolve further under regulatory pressures, such as the U.S. EPA's ENERGY STAR program for external power supplies, which established efficiency standards starting in 2005 to limit no-load power consumption and mandate average efficiencies above 70% for Class A devices, prompting design optimizations like synchronous rectification.^[12] In the 2010s, the active clamp flyback (ACF) topology emerged as a key enhancement, incorporating a clamp switch to recycle leakage energy and achieve zero-voltage switching (ZVS), boosting efficiencies to over 90% in adapters and chargers while enabling higher switching frequencies.^[13] Post-2020, integration of wide-bandgap devices like gallium nitride (GaN) and silicon carbide (SiC) MOSFETs has further improved performance, allowing faster switching speeds up to several MHz and power densities exceeding 10 W/in³ in compact USB-PD chargers.^[14]

Circuit Structure

Key Components

The flyback converter relies on several essential hardware elements to achieve isolated DC-DC power conversion, with components divided primarily between the input and output sides of the transformer, supplemented by protective and regulatory support elements.^[15]^[16] On the input side, the DC source supplies the unregulated input voltage, typically ranging from 10 V to 50 V in low-power applications, to the primary winding of the transformer, which stores magnetic energy in its core during the switch-on period.^[16]^[17] The high-side or low-side switch, commonly a MOSFET, connects the primary winding to the DC source to initiate energy storage; for instance, a 150 V, 53.7 A rated MOSFET handles peak currents up to 4.8 A while managing switching losses.^[15]^[16] A snubber circuit, often an RC network, is connected across the switch to suppress voltage spikes caused by transformer leakage inductance, preventing device failure.^[18] The output side features the secondary winding, which releases the stored energy to the load when the primary switch is off, providing galvanic isolation and voltage step-up or step-down based on the turns ratio.^[17] A fast-recovery rectifier diode, such as a Schottky type, conducts during this energy transfer phase to direct current to the load while blocking reverse flow; it must withstand peak currents significantly higher than the average output current, often up to 14 A in a 2 A design.^[15]^[16] The output capacitor, typically electrolytic or ceramic (e.g., 500 µF total at 6.3 V), smooths the pulsating output voltage to deliver a stable DC supply.^[18]^[16] Support components include a feedback mechanism, such as an optocoupler, which isolates the control signal from the output side to enable voltage regulation without compromising isolation, or an auxiliary winding on the transformer for primary-side sensing in no-opto designs.^[18]^[16] A current-sense resistor, valued at around 20 mΩ, monitors primary current for overcurrent protection and limits peak values to safeguard the switch.^[15]^[16] Component selection emphasizes voltage and current margins to account for transients: the switch must be rated for at least the peak drain-source voltage, calculated as the input voltage plus the reflected output voltage \left(V_{in} + \frac{V_{out}}{n}\right), where n is the secondary-to-primary turns ratio \left(n = \frac{N_s}{N_p}\right), plus 10-30% margin for ringing.^[15] Similarly, the rectifier diode requires a reverse voltage rating exceeding the output voltage plus the reflected input voltage (V_out + V_in × (N_s / N_p)), with additional margin for spikes, and should use fast-recovery types to minimize conduction losses.^[15]^[18] A representative example is a 10-50 V input to 5 V / 2 A output converter using an off-the-shelf transformer with 12 µH primary inductance and a 4:1 turns ratio (n = 0.25), paired with a 150 V MOSFET switch, 40 V secondary rectifier, and 500 µF output capacitance for 85% efficiency at 10 W.^[16]

Transformer Configuration

In flyback converters, the transformer functions as a coupled inductor rather than a conventional transformer, with energy primarily stored in the magnetizing inductance L_m of the primary winding during the switch-on period and transferred to the secondary during the off period.^[19] Unlike true transformers, which rely on tight mutual coupling to minimize energy storage and avoid saturation, the flyback design intentionally incorporates an air gap in the core to increase L_m and enable energy accumulation without core saturation.^[17] This configuration provides galvanic isolation while supporting buck-boost operation.^[2] Core selection emphasizes materials suited to high-frequency switching, typically ferrite cores for operations above 50 kHz in discontinuous conduction mode, due to their low losses and ability to handle large flux swings.^[19] Powdered iron or Kool-Mu cores may be used for continuous mode applications requiring higher saturation flux density B_{SAT}, though they incur greater core losses.^[19] The air gap, often placed over the center leg of an E-core or similar shape, prevents saturation by confining energy storage to the gap, where the effective permeability is low; distributed gaps in laminated metal cores can further reduce fringing fields.^[19] Pre-gapped ferrite cores are common to achieve precise inductance without custom machining.^[20] Winding design prioritizes the turns ratio n = N_s / N_p, where N_s and N_p are secondary and primary turns, respectively, to achieve voltage multiplication in step-up configurations or regulation in step-down setups.^[17] Interleaved windings—alternating primary and secondary layers—minimize leakage inductance, which otherwise stores excess energy and generates voltage spikes across the switch upon turn-off.^[19] These spikes, exacerbated by poor coupling, can exceed switch ratings and are mitigated using RCD snubbers on the primary side to clamp the voltage and dissipate the leakage energy.^[2] Parasitic effects from leakage inductance lead to high-frequency ringing and electromagnetic interference (EMI), as the uncoupled energy rings at the switch's drain-source node.^[2] Leakage is ideally kept to 3-5% of L_m through optimized winding geometry, such as long, narrow bobbin windows.^[21] The reset voltage across the magnetizing inductance during the off period is given by

V_{\text{reset}} = V_{\text{in}} \cdot \frac{D}{1 - D},

derived from volt-second balance, where this voltage reflects the secondary side and must remain below core saturation limits.^[19] For multi-output flyback converters, a single primary winding couples to multiple secondary windings, enabling cost-effective generation of isolated rails at different voltages, such as 24 V, 15 V, and 5 V, all referenced to a common potential on the secondary side.^[22] This shared-core approach normalizes design to the lowest voltage output for turns ratio calculation, though cross-regulation challenges arise from varying load currents across outputs.^[19]

Operation

Discontinuous Conduction Mode

In discontinuous conduction mode (DCM), the flyback converter operates such that the magnetizing current in the transformer falls to zero before the start of the next switching cycle, creating an idle period where no current flows in either the primary or secondary winding.^[15] This mode is particularly suitable for low-power applications, typically below 20-50 W, where the load current is light enough to allow full demagnetization of the transformer core within each cycle. The operation emphasizes simplicity in design and control compared to continuous conduction mode, as the absence of residual current simplifies voltage regulation and reduces certain parasitic effects.^[23] The switching cycle in DCM consists of three distinct phases. During the switch-on phase, the primary-side switch (typically a MOSFET) is closed, applying the input voltage V_{in} across the primary winding. The magnetizing current i_{Lm} ramps up linearly from zero, reaching a peak value given by

I_{pk} = \frac{V_{in} \cdot D}{L_m \cdot f_{sw}},

where D is the duty cycle, L_m is the magnetizing inductance, and f_{sw} is the switching frequency.^[23] In the switch-off phase, the switch opens, and the stored energy transfers to the secondary side through the output diode, which becomes forward-biased. The secondary current i_s = i_{Lm}/n (with n = N_s / N_p the turns ratio), decreases linearly to zero, with the voltage across the secondary winding V_{out} + V_D (where V_D is the diode forward drop).^[15] The idle phase follows, during which both primary and secondary currents are zero, allowing the transformer to fully demagnetize without additional clamping circuitry. The voltage gain in DCM is load-dependent and nonlinear, derived from energy balance across the cycle. For an ideal case with turns ratio n = 1, the gain is

\frac{V_{out}}{V_{in}} = \frac{D}{\sqrt{K}},

where K = \frac{2 L_m f_{sw}}{R_{load}} and R_{load} is the output load resistance.^[15] This relationship highlights how lighter loads (higher R_{load}, lower K) increase the gain for a fixed D, necessitating feedback for regulation, often implemented via an optocoupler to sense output voltage and adjust the duty cycle.^[15] DCM offers several advantages, including inherent demagnetization during the idle phase, which prevents magnetic saturation and eliminates the need for active reset circuits. It also avoids the requirement for slope compensation in current-mode control, as the zero-current condition inherently stabilizes the loop without subharmonic oscillations.^[23] Overall, the mode enables simpler control circuitry and higher efficiency at light loads due to reduced conduction losses.^[15] Key waveforms in DCM illustrate the mode's characteristics. The magnetizing current i_{Lm} forms a triangle: rising linearly from 0 to I_{pk} during the on-time D T_s (where T_s = 1/f_{sw}), then falling to zero during the off-time portion until demagnetization. The switch voltage v_{DS} is near zero (clamped by input voltage minus drop) during on-time, then spikes to V_{in} + n V_{out} + V_D upon turn-off, followed by ringing during idle due to parasitic capacitances and leakage inductance. The diode current i_D is zero during switch-on (reverse-biased), peaks at I_{pk}/n at turn-off, and ramps down linearly to zero. These waveforms ensure zero average magnetizing current over the cycle, confirming DCM operation.^[15] The boundary condition between DCM and continuous conduction mode (CCM) occurs at a critical load where the off-time exactly equals the demagnetization time, with no idle period. This threshold is defined by the minimum load resistance R_{crit} = \frac{2 L_m f_{sw} (V_{out})^2}{V_{in}^2 D^2} (for n=1), below which (heavier loads) the converter transitions to CCM.^[15] Operation in DCM requires loads above this boundary to maintain the zero-current idle phase.

Continuous Conduction Mode

In continuous conduction mode (CCM), the flyback converter operates with a persistent magnetizing current in the transformer that does not decay to zero at the end of each switching cycle, making it suitable for higher power levels compared to discontinuous conduction mode.^[24] This mode ensures that the secondary rectifier current flows continuously until the next switch turn-on, avoiding an idle period and allowing for more efficient energy transfer at heavier loads.^[25] The operation consists of two primary phases per switching cycle. During the switch-on phase, the power switch closes, applying the input voltage across the primary winding, which causes the magnetizing current to increase linearly from its minimum value I_{\min} to a peak value, storing energy in the transformer core.^[24] In the subsequent switch-off phase, the switch opens, and the stored energy transfers to the output through the secondary winding via the rectifier diode, with the magnetizing current decreasing linearly to I_{\min} > 0 before the next cycle begins, maintaining continuity without interruption.^[24] This continuous flow contrasts with modes where current reaches zero, enabling CCM for applications requiring stable output under varying loads.^[25] The voltage gain in CCM is given by the ideal transfer function:

\frac{V_{\text{out}}}{V_{\text{in}}} = \frac{D}{1 - D} \cdot \frac{1}{n}

where D is the duty cycle and n = N_s / N_p is the transformer turns ratio (secondary to primary).^[24] This relationship holds independent of load variations in the ideal case, as the continuous current ensures consistent volt-second balance across the transformer, though practical implementations account for diode forward voltage drops and leakage effects.^[25] Waveforms in CCM exhibit continuous triangular shapes for both primary and secondary currents: the primary current ramps up during the on-time and the secondary current ramps down during the off-time, with no zero-current interval, resulting in lower peak currents and reduced ripple compared to discontinuous operation.^[24] The switch voltage during the off-phase is clamped by the output voltage reflected through the turns ratio, aiding in predictable behavior.^[25] Transition to CCM from discontinuous conduction mode occurs at higher load currents or lower switching frequencies, where the critical current threshold is exceeded, preventing the magnetizing current from fully discharging within the off-time.^[24] For instance, increasing the output load beyond the boundary point shifts the operation into CCM, narrowing the duty cycle range while improving efficiency at elevated power levels.^[25] Key challenges in CCM include the presence of a right-half-plane zero (RHPZ) in the control-to-output transfer function, which reduces phase margin and limits the achievable control bandwidth, often capping it below the RHPZ frequency (e.g., around 25 kHz in typical designs).^[25] Additionally, in current-mode control, duty cycles exceeding 50% necessitate slope compensation to mitigate subharmonic oscillations and ensure stability, as the sensing of inductor current can otherwise lead to unstable feedback.^[24] These factors demand careful design of the compensation network to maintain robust performance.^[25]

Control Methods

Voltage Mode Control

Voltage mode control in flyback converters employs pulse-width modulation (PWM) to regulate the output voltage by adjusting the duty cycle based solely on voltage feedback, without incorporating current sensing in the inner loop. An error amplifier compares the sensed output voltage—typically fed back through an optocoupler for galvanic isolation—to a stable reference voltage, generating an error signal that drives the PWM modulator within an integrated controller IC, such as the UCC3570.^[26] This modulation varies the switch on-time to maintain the desired output, with the ramp signal for PWM comparison often incorporating voltage feed-forward to compensate for input voltage variations and enhance line regulation.^[26] The control-to-output transfer function G_{vd}(s) in voltage mode control is characterized by a double pole arising from the LC filtering action of the transformer's magnetizing inductance L_m and the output capacitance C, typically located at frequency f_{LC} = \frac{D'}{2\pi n \sqrt{L_m C}}, where D' is the off-duty cycle and n is the transformer turns ratio.^[27] This results in a second-order system response, with the gain at DC given by G_{d0} = \frac{V_{out}}{D D'}, though full expressions account for parasitics, the right-half-plane zero in continuous conduction mode (CCM), and mode of operation.^[27] In discontinuous conduction mode (DCM), the transfer function simplifies without a right-half-plane zero, aiding analysis, whereas CCM introduces additional complexity from energy storage continuity.^[27] Achieving stability requires a compensation network, such as a Type II or Type III error amplifier configuration, to provide sufficient phase boost and counteract the 180° phase shift from the LC double pole, ensuring adequate phase margin (typically >45°).^[27] The crossover frequency, or loop bandwidth, is generally limited to less than one-tenth of the switching frequency f_{sw} (e.g., <10 kHz for f_{sw} = 100 kHz) to avoid amplification of switching noise and maintain stability across operating conditions.^[27] Voltage feed-forward techniques, as in the UCC3570, further improve stability by dynamically adjusting the oscillator ramp slope proportional to the input voltage, reducing loop gain variations.^[26] Implementation often relies on isolated feedback via optocouplers like the 4N25 to transmit the error signal across the isolation barrier, while an auxiliary transformer winding supplies bias power to the controller or enables primary-side voltage sensing in non-isolated designs.^[26] This approach avoids the need for secondary-side control circuitry in some cases but requires careful selection of optocoupler transfer characteristics for linear operation. Voltage mode control offers simplicity in design and compensation, making it well-suited for DCM operation where flyback converters handle low-power applications efficiently without subharmonic oscillations.^[28] However, it suffers from slower transient response in CCM, as changes in load or line voltage propagate through the full plant dynamics without the stabilizing effect of an inner current loop, potentially leading to output overshoot or undershoot during disturbances.^[28]

Current Mode Control

Current mode control in flyback converters employs a dual-loop regulation strategy, featuring an inner current feedback loop and an outer voltage feedback loop, to enhance dynamic response and provide inherent cycle-by-cycle current limiting for protection against overcurrent conditions.^[29] The inner loop regulates the inductor current by sensing it through a low-value resistor connected in series with the switch, converting the current to a voltage signal that is compared against a reference to modulate the pulse-width modulation (PWM) duty cycle.^[30] There are two primary types of current mode control: peak current mode and average current mode. In peak current mode, the controller senses the peak switch current each cycle and terminates the on-time when this sensed voltage exceeds a threshold derived from the error amplifier output, effectively resetting the PWM each switching period.^[31] This approach provides fast transient response and inherent input voltage feedforward, as the current slope naturally incorporates variations in input voltage.^[29] Average current mode, in contrast, uses a high-gain integrating error amplifier to regulate the average inductor current, offering greater precision in continuous conduction mode (CCM) where peak sensing can introduce errors due to ripple.^[32] It is particularly suited for applications requiring accurate current shaping, such as power factor correction in flyback topologies.^[32] To ensure stability, especially in CCM where duty cycles exceed 50%, slope compensation is essential to prevent subharmonic oscillations, which manifest as alternating current amplitudes that can destabilize the converter.^[29] This involves adding an artificial ramp signal to the sensed current waveform at the PWM comparator; the ramp slope must exceed half the magnitude of the inductor's rising current slope (typically given by V_{IN}/L, where V_{IN} is the input voltage and L is the primary inductance) to dampen perturbations in a single cycle.^[29] Without adequate compensation, CCM operation risks these oscillations, limiting the control's reliability at higher duty cycles.^[29] The stability benefits of current mode control include improved phase margin and higher loop bandwidth compared to voltage mode, as the inner current loop splits the output filter's complex poles into two real poles, simplifying compensation and enabling faster response to load changes.^[29] Additionally, the inherent feedforward from input voltage variations through the current slope enhances line regulation without additional circuitry.^[31] Implementation often relies on integrated circuits such as the UC3843, a fixed-frequency PWM controller that incorporates the current sensing comparator, error amplifier, and oscillator, facilitating straightforward design for off-line and DC-DC flyback applications up to 500 kHz switching frequencies.^[30] Since the early 2000s, primary-side sensing techniques have gained prominence, allowing regulation without optocouplers by sampling the reflected output voltage across the auxiliary winding during the off-time, thus reducing component count, cost, and improving reliability in isolated designs.^[33] A notable drawback is the sensitivity to noise in the current sensing path, as high-frequency switching transients can corrupt the sensed signal, potentially causing erratic PWM behavior or false triggering, necessitating careful filtering with RC networks.^[29]

Design and Analysis

Core Equations

The core equations of the flyback converter provide the mathematical foundation for analyzing its steady-state behavior, power transfer, component stresses, and control dynamics. These equations are derived from fundamental principles such as inductor volt-second balance, energy conservation in the magnetizing inductance, and charge balance in the output capacitor. They apply primarily to the ideal case, with extensions for practical losses like diode forward voltage drop V_f. The transformer's turns ratio n = N_s / N_p (secondary to primary turns) plays a key role in voltage scaling and stress calculations but cancels out in ideal power transfer relations for discontinuous conduction mode (DCM).^[15]

Volt-Second Balance on Magnetizing Inductance

The volt-second balance principle ensures steady-state operation by requiring the net volt-seconds across the magnetizing inductance L_m over one switching period T_s = 1/f_{sw} to be zero, preventing magnetic flux runaway. In the flyback converter, during the switch on-time t_{on} = D T_s (where D is the duty cycle), the voltage across L_m is V_{in}, so the volt-seconds accumulated are V_{in} D T_s. During the switch off-time, the voltage across L_m reverses to -\frac{(V_{out} + V_f)}{n} (reflected output voltage plus diode drop, assuming ideal clamping), but only for the diode conduction fraction D_2 T_s in DCM (where D_2 < 1 - D); the remaining time has zero current and thus zero volt-seconds contribution in ideal analysis. The balance equation is thus:

V_{in} D T_s = \frac{(V_{out} + V_f)}{n} D_2 T_s

Simplifying,

\frac{V_{out} + V_f}{V_{in}} = n \frac{D}{D_2}

This relation links duty cycle to output voltage via turns ratio and conduction fractions. For continuous conduction mode (CCM), D_2 = 1 - D, yielding the classic gain V_{out} = n V_{in} \frac{D}{1 - D} (neglecting V_f). In DCM, D_2 is determined separately from current ramp-down, ensuring the equation holds alongside power balance. Derivations start from Faraday's law (v_L = L_m \frac{di_m}{dt}) integrated over subintervals, confirming the average inductor voltage \langle v_L \rangle = 0.^[34]^[15]

Magnetizing Current and Stored Energy

The magnetizing current i_m ramps linearly during the on-phase due to applied input voltage. Starting from zero in DCM (or a non-zero value in CCM), the peak magnetizing current is

I_{pk} = \frac{V_{in} t_{on}}{L_m} = \frac{V_{in} D}{L_m f_{sw}}

This follows from integrating v_L = L_m \frac{di_m}{dt} during t_{on}, yielding a triangular waveform with slope V_{in}/L_m. The energy stored in L_m at peak is the standard inductor energy formula

E = \frac{1}{2} L_m I_{pk}^2

In each cycle, this energy is fully transferred to the output in DCM, forming the basis for power calculations. Practical designs select L_m to limit I_{pk} for reduced conduction losses, with I_{pk} typically 20-50% above average for ripple control.^[19]

Output Power in DCM

In DCM operation, all stored energy per cycle is delivered to the load, leading to the average output power

P_{out} = \frac{1}{2} L_m I_{pk}^2 f_{sw}

Substituting I_{pk} gives

P_{out} = \frac{V_{in}^2 D^2}{2 L_m f_{sw}}

This derives from input power balance: average primary current is \frac{1}{2} I_{pk} D, so P_{in} = V_{in} \cdot \frac{1}{2} I_{pk} D = \frac{V_{in}^2 D^2}{2 L_m f_{sw}}, equaling P_{out} in ideal conditions (turns ratio effects cancel). The equation holds for low-to-moderate power levels where DCM dominates, typically up to 50 W.^[35]

Duty Cycle Relation at DCM Boundary

For a given output power in DCM, the required duty cycle satisfies

D = \sqrt{\frac{2 P_{out} L_m f_{sw}}{V_{in}^2}}

This follows directly from rearranging the power equation, assuming ideal transfer and operation below the CCM boundary (where D_2 < 1 - D). At the DCM-CCM boundary, this D equals the CCM value from volt-second balance, marking the minimum L_m for CCM at full load: L_{m, crit} = \frac{(1 - D) D V_{in}}{f_{sw} I_{out}} (with D from CCM gain). Designs often target boundary operation at minimum V_{in} for optimal efficiency.^[15]

Component Stress Factors

The maximum voltage stress on the primary switch (MOSFET drain-source) occurs at turn-off, clamping to input plus reflected output:

V_{DS, max} = V_{in} + \frac{(V_{out} + V_f)}{n}

Here, n = N_s / N_p scales the secondary voltage to the primary side; add 20-50 V margin for leakage spikes. For conduction losses, RMS currents are key: primary RMS current (triangular waveform in DCM) is

I_{P, RMS} = I_{pk} \sqrt{\frac{D}{3}}

Secondary RMS current is

I_{S, RMS} = \frac{I_{pk}}{n} \sqrt{\frac{D_2}{3}}

These derive from waveform RMS definitions (\sqrt{\frac{1}{T_s} \int i^2 dt}) and inform MOSFET/diode selection, with I_{RMS} scaling losses as I^2 R.^[36]^[37]

Small-Signal Model for Control Design

Small-signal analysis linearizes the converter around a DC operating point for feedback design, replacing the nonlinear switch with averaged dependent sources driven by duty perturbation \hat{d}(t). The control-to-output transfer function for voltage-mode control in CCM is approximately

\frac{\hat{v}_{out}(s)}{\hat{d}(s)} = G_{do} \frac{1 - \frac{s}{\omega_{RHPZ}}}{1 + \frac{s}{\omega_p}}

where G_{do} = \frac{V_{out}}{D(1 - D)} is DC gain, \omega_p = \frac{1 - D}{n \sqrt{L_m C}} is the dominant LC resonance pole (approximating the complex pair), and \omega_{RHPZ} = \frac{(1 - D)^2 R_o}{n^2 L_m D} is right-half-plane zero (destabilizing at high loads). Derivation uses state-space averaging: define states (magnetizing current, output voltage), perturb (i_m = I_m + \hat{i}_m, etc.), and apply PWM \hat{d} to yield low-frequency AC model. This model guides compensator design, e.g., type-II for pole-zero cancellation. In DCM, the right-half-plane zero is absent due to discontinuous states, simplifying compensator design.^[27]

Efficiency Optimization

The efficiency of a flyback converter is fundamentally limited by various power losses, which can be categorized into conduction losses, switching losses, and core losses. Conduction losses primarily arise from I²R effects in the transformer windings and the primary switch, where the RMS current squared multiplied by the resistance dissipates energy as heat.^[38] Switching losses occur due to the charging and discharging of parasitic capacitances during transitions, approximated as (1/2) C V² f_sw, where C is the switch output capacitance, V is the voltage across it, and f_sw is the switching frequency; these losses become prominent at higher frequencies.^[39] Core losses stem from hysteresis in the magnetic material and eddy currents induced by the alternating flux, which increase with frequency and flux density.^[17] To optimize efficiency, several strategies target these loss mechanisms. Soft-switching techniques, such as those implemented in the active clamp flyback (ACF) topology, recycle leakage inductance energy to achieve zero-voltage switching (ZVS) across the primary switch, significantly reducing turn-off losses and eliminating the need for dissipative snubbers.^[40] On the secondary side, replacing the output diode with a low R_ds(on) MOSFET enables synchronous rectification, which minimizes forward voltage drop and conduction losses compared to traditional diode rectification, potentially improving efficiency by 2-5% in medium-power designs.^[41] These approaches leverage the core power equations to balance magnetizing and leakage inductances for resonant operation.^[13] The overall efficiency η is given by:

\eta = \frac{P_\text{out}}{P_\text{out} + P_\text{conduction} + P_\text{switching} + P_\text{core}}

where P_out is the output power and the losses are as defined earlier; typical values for a 50 W flyback converter range from 80% to 90%, depending on component selection and operating conditions.^[42] However, trade-offs exist in design choices, such as increasing the switching frequency f_sw to reduce transformer size, which heightens switching and core losses unless mitigated by ZVS conditions that utilize controlled leakage inductance for resonant discharge of switch capacitance.^[17] In modern implementations, gallium nitride (GaN) devices in ACF topologies have achieved efficiencies exceeding 95% at power levels up to 65 W by enabling higher f_sw with minimal additional losses and inherent ZVS.^[43]^[44]

Limitations

Mode-Specific Drawbacks

In discontinuous conduction mode (DCM), the flyback converter exhibits high peak currents in the primary and secondary windings, which elevate conduction losses due to increased I²R effects in the switches and transformer. These elevated peak currents also generate significant electromagnetic interference (EMI) from the abrupt current transitions and discontinuous operation.^[15]^[45] DCM operation can involve variable switching frequency in control schemes like quasi-resonant or boundary conduction modes, complicating EMI filtering and audio susceptibility. Additionally, the mode's inherent high output voltage ripple—approximated as ΔV_out ≈ (I_out × D) / (f_sw × C_out), where the capacitor supplies the load during the switch-on period—necessitates larger output capacitance, making DCM unsuitable for power levels exceeding 100 W without excessive component sizing.^[15]^[31]^[46] In continuous conduction mode (CCM), subharmonic oscillations arise in current-mode control when the duty cycle exceeds 50%, demanding slope compensation to stabilize the loop and prevent period-doubling instability. The presence of a right-half-plane zero in the control-to-output transfer function limits the achievable bandwidth to roughly one-tenth of the switching frequency, resulting in higher closed-loop output impedance and slower transient response compared to DCM.^[47]^[25]^[45] CCM requires a higher average magnetizing current to maintain continuous flow, increasing the risk of transformer core saturation under load variations or tolerances and necessitating larger core sizes to handle the DC bias. This mode also exhibits higher output impedance in the small-signal model due to the inductive energy storage dynamics.^[15]^[24] Transitioning between DCM and CCM, particularly at the boundary under varying loads or input voltages, can induce instability such as oscillations or poor regulation if dead time or control timing is not adequately managed, often requiring adaptive control techniques for seamless operation. To mitigate these mode-specific issues, designers typically select DCM for low-power applications below 50 W, where its simplicity outweighs the drawbacks, while reserving CCM for higher powers with appropriate compensation.^[15]^[24]

Practical Implementation Challenges

One of the primary challenges in implementing flyback converters is managing electromagnetic interference (EMI) and ensuring electromagnetic compatibility (EMC), primarily due to high dv/dt rates from leakage inductance, which generate voltage spikes and radiated emissions. Interwinding capacitance between primary and secondary windings further exacerbates common-mode (CM) noise by coupling high-frequency currents to ground, often requiring extensive filtering to meet standards like CISPR 22. Mitigation strategies include incorporating electrostatic shields, such as copper foil layers connected to the primary ground, which can reduce CM EMI by up to 26 dB in quasi-resonant designs, and interleaving transformer windings to minimize leakage inductance from typical values of 4-6 μH down to 3-4 μH. PCB layout plays a critical role, with recommendations to minimize high-current loop areas (reducing inductive spikes via V = L di/dt, where L ≈ 20 nH/inch for traces) and employ ground planes to suppress emissions by 10-20 dB; additionally, RC snubbers across output diodes dampen reverse recovery spikes, though they introduce a 1-2% efficiency penalty.^[48]^[49]^[50] Thermal management poses significant hurdles, as heat dissipation from the power switch (e.g., MOSFET) and output diode can lead to thermal runaway in compact designs, particularly under high ambient temperatures exceeding 50°C. Effective heat sinking is essential, with low thermal resistance packages like LLP (θ_JC ≈ 40°C/W) outperforming traditional MSOP-8 (θ_JA ≈ 200°C/W) by enabling direct PCB soldering to power planes and thermal vias for better conduction. Derating is standard practice, reducing maximum output power by 20-50% at elevated ambients to keep junction temperatures below 125°C, as calculated via θ_JA = θ_JC + θ_CA where ambient T_A directly impacts reliability; poor transformer design can also cause localized hotspots from core losses, necessitating larger copper areas or external heatsinks.^[51]^[24] Protection features are crucial for reliability, with overvoltage protection (OVP) typically implemented via Zener diodes on the output to clamp transients, triggering at 4.4-4.67 V on sense pins in controllers like UCC28781 to prevent component damage. Overcurrent protection (OCP) uses current-sense resistors to limit peak currents at 1.14-1.27 V thresholds, often with auto-recovery after 1.2-2.4 s delays, while short-circuit handling employs hiccup modes that cycle the converter off for 160 ms upon detecting output faults, avoiding sustained stress. These features, integrated in modern ICs, address mode-specific risks like voltage overshoot in discontinuous conduction but require careful calibration to avoid false trips.^[52]^[53] In multi-output flyback converters, cross-regulation is a significant challenge, where a load change on one output causes substantial voltage variation on the others due to the shared transformer magnetizing current. This inherent limitation often necessitates additional post-regulation techniques, such as linear regulators, preloading resistors, or zener clamps on auxiliary outputs, to achieve tight regulation across all rails.^[54] Cost and size trade-offs arise in component selection, where integrated controllers (e.g., UCC287xx series) reduce discrete parts and PCB area by combining drivers, sensing, and protection, lowering overall bill-of-materials costs by 20-30% compared to discrete MOSFET-plus-IC setups, though they limit flexibility in high-power applications above 100 W. PCB layout optimization is key to minimizing size, with multi-layer boards enabling compact traces while avoiding slot antennas from ground splits; however, adding EMI filters and shields increases board area by 10-15%, balancing compliance against form-factor constraints in adapters or chargers.^[50]^[55] Testing flyback converters involves verifying load and line regulation, typically targeting ±1% variation over 10-100% load and ±10% input voltage ranges, using precision loads to ensure stability under dynamic conditions. Compliance with standards like IEC 62368-1 requires EMI scans, safety isolation tests (e.g., 3 kV AC hipot), and thermal cycling to validate derating; failures often stem from inadequate filtering, necessitating iterative prototyping with spectrum analyzers for conducted/radiated emissions below Class B limits.^[56]^[57]

Applications

Low-Power Power Supplies

Flyback converters are widely employed in low-power AC-DC adapters, typically rated from 5 W to 20 W, for charging mobile phones, laptops, and other portable devices due to their ability to provide isolated power conversion in a compact form factor.^[58] These adapters benefit from the flyback's suitability for offline conversion from mains voltage to low DC outputs like 5 V or 12 V. Additionally, flyback converters power standby supplies in televisions and personal computers, often under 5 W, where minimal quiescent power draw is essential to meet energy regulations.^[59]^[60] The topology's advantages in these applications include its simple design with fewer components compared to other isolated converters, as the transformer serves dual roles in energy storage and galvanic isolation, ensuring user safety without additional inductors.^[4] This inherent isolation complies with safety standards like IEC 62368-1, while the single-switch configuration reduces bill-of-materials costs, making it ideal for cost-sensitive consumer products.^[61] In design, discontinuous conduction mode (DCM) is preferred for these low-power supplies to simplify control and achieve higher efficiency at light loads, avoiding the need for complex current sensing.^[62] Primary-side regulation (PSR) further lowers costs by eliminating optocouplers and secondary-side feedback circuits, relying instead on reflected voltage from the auxiliary winding for output control.^[63] Representative examples include USB chargers based on flyback topology, which commonly achieve around 85% efficiency at full load, balancing performance with affordability.^[64] Integration with specialized ICs like Power Integrations' TOPSwitch family enhances reliability and efficiency in these adapters by combining the power MOSFET, controller, and protection features into a single package.^[65] Flyback converters dominate the market for offline supplies under 75 W in the 2020s, serving as the most popular topology for adapters and chargers owing to their versatility and low implementation cost.^[66]

High-Voltage and Specialized Uses

Flyback converters are widely employed in high-voltage applications due to their ability to achieve significant voltage step-up ratios. In cathode ray tube (CRT) displays, particularly in televisions from the 1990s, flyback transformers generated the necessary high voltages, often up to 30 kV, to accelerate electron beams for image formation.^[67]^[68] Similarly, these converters power xenon flash lamps by providing the high-voltage pulses required for ionization and discharge, as demonstrated in designs for short-arc pulsed xenon lamps where flyback topologies ensure reliable triggering and energy delivery.^[69] In medical X-ray generators, flyback converters serve as efficient high-voltage sources for low-current applications, enabling precise control in diagnostic equipment while minimizing component count.^[70]^[71] Beyond general high-voltage needs, flyback converters find specialized uses in environments demanding isolation and multi-output capabilities. For multi-output LED drivers, the topology supports multiple secondary windings to power strings of LEDs at varying currents, with techniques like current balancing ensuring uniform illumination in lighting systems.^[72]^[73] In electric vehicles (EVs), flyback converters provide isolated auxiliary 12 V supplies from the high-voltage battery (typically 400 V), replacing traditional lead-acid batteries and enabling reliable powering of low-voltage electronics during main battery faults.^[74] For renewable energy, flyback-based micro-inverters convert low-power solar outputs (<100 W per panel) to grid-compatible AC, incorporating maximum power point tracking for optimal energy harvest in distributed photovoltaic systems.^[75]^[76] The suitability of flyback converters for these applications stems from their inherent advantages, including high step-up ratios achievable with turns ratios greater than 10:1, which facilitate voltage multiplication without additional stages, and their tolerance for discontinuous conduction mode operation, allowing simpler control and reduced electromagnetic interference in pulsed or variable-load scenarios.^[77] In modern implementations, gallium nitride (GaN)-based flyback converters enable 65 W USB Power Delivery (PD) fast chargers with improved switching speeds and thermal performance, supporting compact designs for portable electronics.^[78] Additionally, active clamp flyback (ACF) variants achieve efficiencies exceeding 90% in adapters by recycling leakage energy, reducing losses in high-density power supplies.^[13]^[79] High-voltage flyback designs must address significant challenges related to insulation and safety. Robust insulation materials are essential to withstand voltage stresses, preventing breakdown in the transformer and components, while creepage distances— the shortest path along the surface between conductive parts—must comply with standards like IEC 60664-1 to mitigate risks of arcing or flashover in polluted environments.^[80]^[81] These requirements often necessitate specialized PCB layouts and potting to ensure reliable operation under international safety regulations.^[82]

References

[1]
[PDF] How to Design Flyback Converter With LM3481 Boost Controller
The flyback topology is essentially the buck-boost topology that is isolated by using a transformer as the storage inductor.Missing: definition | Show results with:definition
[2]
How to Choose a Forward vs. a Flyback Converter - Analog Devices
May 2, 2024 · A flyback converter is a type of isolated SMPS that uses a transformer to transfer energy from the input to the output. It can be configured in ...
[3]
[PDF] Switching regulator fundamentals (Rev. C) - Texas Instruments
Flyback converters operate in either continuous mode (where the secondary current is always > 0) or discontinuous mode (where the secondary current falls to ...
[4]
[PDF] Isolated Supply Overview and Design Trade-Offs - Texas Instruments
The flyback converter uses a single FET to energize the transformer, utilizes a single-output diode, and does not need an output inductor. As a result, the.
[5]
[PDF] of 12 10/25/2021 15:31 Experiment: The Flyback DC-DC Converter ...
Oct 25, 2021 · The Flyback converter is an isolated DC-DC converter using a transformer to store energy, with the transformer overseeing energy storage, ...Missing: explanation | Show results with:explanation
[6]
[PDF] Isolated Switch-Mode dc-to-dc Converters
Unlike the forward converter, the flyback converter doesn¶t need an output inductor; it uses only one diode and does not suffer from a core saturation prob lem.
[7]
Flyback power converters, Part 1: basic principles
Apr 15, 2019 · The flyback design is a converter approach which has been used for 70+ years and is still in use, now using an IC as a controller.<|control11|><|separator|>
[8]
History of Switch Mode Power Supplies (SMPS) - XP Power
Switch mode power supplies (SMPS) offer advantages including compactness and efficiency. Here we delve into the history of these converters.
[9]
1980 - A Pivotal Point in the Power Industry! - PSMA Update
But then, working on the Apple II Rob Holt designed a 38W multi-output off-line flyback switching power supply (Figure 04) for which he filled a patent in ...
[10]
[PDF] Building An Average Model For Primary-Side Regulated Flyback ...
To create this model, we will use the pulse width modulation (PWM) switch model introduced in the 90s and adapted to quasi-resonant (QR) operation in ...
[11]
[PDF] ENERGY STAR External Power Supply Decision Memorandum
The second half of the ENERGY STAR specification specifies the maximum ac power that may be used by a qualifying EPS in the No-Load condition: 0.5 watts where.Missing: flyback | Show results with:flyback
[12]
[PDF] High-Density AC-DC Power Supplies using Active-Clamp Flyback ...
This paper introduces the principle of operation of the active clamp flyback topology along with its merits and demerits. Also, a technique to improve its ...Missing: 2010s | Show results with:2010s
[13]
[PDF] Integrated High Voltage GaN Solutions
Integrated GaN solutions offer high efficiency, high switching frequencies, reduced form factor, reduced power losses, and higher power density. MasterGaN ...Missing: post- | Show results with:post-
[14]
[PDF] Designing a DCM flyback converter - Texas Instruments
Flyback converters can operate either in continuous-conduction mode (CCM) or discontinuous-conduction mode. (DCM). For many low-power and low-current ...Missing: sqrt | Show results with:sqrt
[15]
[PDF] 5V/2A, Synchronous No-Opto Isolated Flyback DC-DC Converter ...
An isolated no-opto flyback DC-DC converter using the MAX17690 and MAX17606 is demonstrated for a 5V DC output application. The power supply delivers up to 2A ...
[16]
A Guide to Flyback Transformers | Coilcraft
### Key Components of Flyback Converter
[17]
[PDF] Flyback converter design considerations - Texas Instruments
Feb 9, 2024 · Let's look at some of the key design considerations for a 53 VDC to 12V at 5A continuous-conduction mode (CCM) flyback. Figure 1 shows a ...
[18]
[PDF] "Magnetics Design 5 - Inductor and Flyback Transformer Design"
A flyback transfonner is actually a multi- winding coupled inductor, unlike the true transfonn- ers discussed in Section 4, wherein energy storage is.
[19]
Flyback Transformer Design for MAX1856 SLIC Power Supplies
Aug 20, 2002 · The gap dimensions determine the inductance per turn achievable for a given core. The manufacturer for pre-gapped ferrite cores or for ...Missing: RCD | Show results with:RCD
[20]
https://www.analog.com/en/resources/technical-articles/flyback-transformer-design-for-max1856-slic-power-supplies.html
[21]
[PDF] 50-W Opto-Regulated Multi-Output Flyback Converter Reference ...
The key part in the reference design is the flyback controller, the UCC28740 device. The self-start feature is implemented via the HV pin which is directly ...<|control11|><|separator|>
[22]
[PDF] AN730 Designing A Wide Input Range DCM Flyback Converter ...
Jul 8, 2002 · Figure 2 shows typical current waveforms of a DCM flyback converter in operation. To simplify circuit analysis, we can convert the flyback ...
[23]
[PDF] Designing a CCM flyback converter - Texas Instruments
This design example covers basic component calculations of a functional CCM flyback design. However, initial estimates often make it necessary to iterate ...Missing: key | Show results with:key
[24]
[PDF] Isolated Continuous Conduction Mode Flyback Using the TPS55340
A flyback operated in CCM reduces peak currents, RMS currents ... The efficiency of a flyback converter is particularly sensitive to switching frequency.
[25]
[PDF] applying the ucc3570 voltage-mode pwm controller to both off-line ...
Its versatility is demonstrated with the description of a 50W, wide input voltage range, off-line inverter and a 48-to-. 5V isolated DC/DC converter, both of ...
[26]
[PDF] AC Modeling of Power Stage in Flyback Converter - Texas Instruments
The switching elements (MOSFET and Diode) are shown in the dashed rectangular box.Missing: key | Show results with:key
[27]
[PDF] Isolated 50 Watt Flyback Converter Using the UCC3809 Primary ...
This 50W isolated flyback converter uses UCC3809 for primary control, UC3965 for secondary, and is designed for telecommunications, with a 5V output.
[28]
[PDF] Understanding and Applying Current-Mode Control Theory
An ideal current-mode converter is only dependent on the dc or average inductor current. The inner current loop turns the inductor into a voltage- controlled ...
[29]
[PDF] UCx84x Current-Mode PWM Controllers datasheet (Rev. H)
The UCx84x series are current-mode PWM controllers for off-line and DC-to-DC converters, with low start-up current, and high-current output.<|control11|><|separator|>
[30]
Designing Flyback Converters Using Peak-Current-Mode Controllers
Nov 27, 2012 · Flyback converters may be operated in discontinuous conduction mode (DCM) or continuous conduction mode (CCM). The component choices, stress ...Missing: V_out / V_in = sqrt<|separator|>
[31]
[PDF] Average Current Mode Control of Switching Power Supplies
Thus it can control input current accurately with buck and flyback topologies, and can control output current with boost and flyback topologies.
[32]
[PDF] Creating a Primary-Side Regulation Flyback Converter Using a ...
Primary-side regulation (PSR) eliminates the need for optocoupler-based feedback by sensing the voltage across the primary or auxiliary.
[33]
[PDF] Derivation of Volt-second Balance - UTK-EECS
Derivation of Volt-second Balance. Volt-Second Balance: Direct Application. Page 2. Current Ripple Magnitude. Buck Cap Charge Balance. Page 3 ...Missing: flyback | Show results with:flyback
[34]
[PDF] Miniature 5W DC-DC Flyback Converter Using the MAX17596
Introduction. Flyback converters are the preferred topology in isolated converters for medium and low power range applications.
[35]
[PDF] ICL88xx flyback design guide - Infineon Technologies
Sep 20, 2021 · PFC flyback converter design In this equation, N is the turns ratio of the transformer and VD is the forward voltage of the output rectifier. ...
[36]
[PDF] Design guide for ZVS QR flyback converter using CoolSET™ SiP
Apr 14, 2025 · This decision directly impacts the reflected voltage (VR), which in turn affects the voltage stress on both the primary MOSFET and the ...
[37]
[PDF] continuous mode flyback converter - TI E2E
The switching Mosfet has three types of losses, conduction loss and switching loss, and gate charge losses: -Conduction losses are equal to: I^2*R losses ...
[38]
Step by step for an optimised flyback design ... - eeNews Europe
Oct 24, 2011 · The switching MOSFET has three types of losses, conduction loss, switching loss, and gate charge loss: Conduction loss is equal to: I 2.R loss ...
[39]
Design considerations of highly-efficient active clamp flyback ...
The active clamp flyback (ACF) allows soft switching under all line and load conditions, eliminating all leakage inductance and snubber losses. This paper ...
[40]
[PDF] AN5499 How to implement adaptive synchronous rectification in ...
Jun 23, 2020 · Substituting diode rectifiers with power MOSFETs in SR reduces power losses and thermal heating in converters because of their very low RDSON ...
[41]
https://www.st.com/resource/en/application_note/an5499-how-to-implement-adaptive-synchronous-rectification-in-flyback-converters-using-stm32-mcus-stmicroelectronics.pdf
[42]
ACF in a GaN World - Power Systems Design
Feb 20, 2024 · ACF is today's most efficient flyback converter topology, achieving close to zero-voltage switching while also recycling the leakage energy.
[43]
GaN-Based Flyback Topologies Ramp Up Efficiency in USB Type-C ...
Aug 23, 2021 · Tagore has compared two flyback DC/DC converter topologies: a quasi-resonant flyback (QRF) and an active-clamp flyback (ACF) topology for GaN-based 65-W USB ...
[44]
[PDF] The Difference between CCM and DCM Explained
May 27, 2022 · A flyback converter's two operation modes seem very similar, but each has its own set of advantages and drawbacks. It is very important for ...
[45]
https://media.monolithicpower.com/mps_cms_document/2/0/2021-seo-the-difference-between-ccm-and-dcm-explained_r1.0.pdf
[46]
[PDF] Under the Hood of Flyback SMPS Designs - Texas Instruments
Right-Half-Plane Zero, CCM Operation. 1:n2. +Vi. Vo la m p. Iout. -. +. -. IP ... Slope compensation to avoid subharmonic oscillation at duty cycle close to or.Missing: drawbacks | Show results with:drawbacks
[47]
[PDF] Flyback transformer design considerations for efficiency and EMI
Sep 2, 2016 · The flyback transformer in this example has three windings: primary, secondary and bias (sometimes called the auxiliary winding). AC/DC power ...<|control11|><|separator|>
[48]
[PDF] Fixing EMI Across the Board - Texas Instruments
So here we look at some of the practical design aspects involved in controlling and testing EMI. The Role of the Transformer in Radiated Emissions (EMI). Very ...Missing: challenges | Show results with:challenges
[49]
[PDF] An Engineer's Guide to Low EMI in DC/DC Regulators
In general, unbalance associated with both converter noise sources and EMI filter parameters can result in such mode transformations [20]. Figure 4.
[50]
[PDF] Thermal Issues and Solutions in Power Management
The challenging environment in equipment destined to power the expanding information infrastructure brings thermal design into sharp focus. The world of modular ...
[51]
[PDF] UCC28781 Zero-Voltage-Switching Flyback Controller with ...
Dec 2, 2021 · A resistor divider between REF and AGND is used to set a voltage at BUR to determine the peak current level when the converter enters adaptive ...
[52]
[PDF] TI Designs: TIDA-00701 - 100-W, 24-V, High Efficiency, High PF ...
• Two undervoltage lockout (UVLO) options, OVP, open-feedback protection and enable circuits ... includes input UVP and output short-circuit protection. Low EMI, ...
[53]
[PDF] Off-Line (Non-Isolated) AC/DC Power Supply Architectures ...
Apr 2, 2019 · Another unique topology that has an integrated active bridge rectifier, switched-cap network and an integrated LDO is shown in this design.
[54]
[PDF] TPS2596 2.7 to 19 V, 0.125 to 2-A, 89-mΩ eFuse With Accurate ...
• IEC 62368 CB certification (pending). • Small footprint: 4.91 mm x 3.9 mm SOIC package. 2 Applications. • Energy meters. • UL 60335-1 15-W LPC in Appliances.
[55]
[PDF] CN-0590 | Circuit Note - Analog Devices
Isolation can also be mandated by compliance to some safety standards such as the IEC. 62368-1 for IT and A/V products, IEC 61010-1 for electrical equip- ment ...
[56]
SiC die target low power AC-DC flyback converters ...
Mar 20, 2019 · Typical low-power flyback applications include consumer electronics chargers such as laptop and mobile device chargers (from 20 to 65 W). Other ...<|separator|>
[57]
TVs and Monitors - Power Integrations
Power Integrations provides AC-DC converter ICs and power factor correction devices optimized for tiny personal TVs to the largest and most advanced 4K sets.
[58]
[PDF] Low-cost flyback solutions for 10-mW standby power
Jan 31, 2014 · For low-power AC/DC conversion, flyback topology remains the preferred choice due to its simplicity and low cost.Missing: PCs | Show results with:PCs
[59]
https://www.power.com/applications/ac-dc-conversion/tvs-and-monitors
[60]
[PDF] Design Guideline for Primary Side Regulated (PSR) Flyback ...
Primary-side regulation (PSR) controls output voltage and current using primary-side info, removing secondary sensing loss and secondary-feedback circuitry.Missing: 1990s | Show results with:1990s
[61]
https://www.monolithicpower.com/en/products/ac-dc/flyback.html
[62]
Maximizing Efficiency In Flyback Power Supplies - EE Times
Oct 20, 2015 · This reduces the losses at maximum load by about 750 mW and improves efficiency from just below 84% to over 88%. Adding a two-switch flyback to ...
[63]
TOPSwitch - Power Integrations
The latest generation of our flagship TOPSwitch series of high efficiency integrated power conversion ICs is TOPSwitch-JX.
[64]
[PDF] High-Power-Density Adapters and Chargers - Infineon Technologies
The most common power topology for adapters and chargers are fly- back converters. They are relatively easy to design and need only one magnetic component.<|separator|>
[65]
30kV Flyback PSU - GardenBallistics
Jul 6, 2022 · This high voltage PSU utilises a high voltage flyback transformer (also known as a Line Output Transformer – LOPT) salvaged from an old black and white TV.
[66]
https://www.infineon.com/dgdl/Infineon-High-power-density_adapters_and_chargers_challenges_and_solutions-Article-v01_00-EN.pdf?fileId=5546d4626eab8fbf016ed6e5b2233b7c
[67]
Design of short-arc xenon flashlamp power supply based on flyback ...
Mar 30, 2021 · The experimental results show that the driving power supply designed has a 100% success rate for lighting the short-arc pulsed xenon lamp, which ...
[68]
Comparison of energy storage devices for diagnostic X-Ray Generator
High voltage power is needed by diverse application fields such as high precision medical ... Indeed, the DC/DC flyback converter is nowadays frequently used in ...
[69]
[PDF] arastirmax-design-and-implementation-high-voltage-generator ...
Generation of high voltage low current can be determined by using Fly back converter as an optimum method which can improve the design of the device to make it ...
[70]
A simple current balancing method for multi-output flyback LED driver
A simple, low-cost, space-saving and precise current balancing method for the multi-output flyback lighting emitting diode (LED) driver is proposed in this ...Missing: converter | Show results with:converter
[71]
[PDF] IRS2982S Multi-output high power factor flyback converter design
Jul 11, 2018 · The IRS2982S is a versatile SMPS controller IC primarily intended for LED drivers in the 5 to 100 W power range suitable for buck, buck-boost ...
[72]
RDR-953Q - 100 W Power Supply Replacing 12 V Battery in 400 V ...
100 W flyback power supply for 400 V DC BEV automotive applications as a replacement for the 12 V lead-acid auxiliary battery, using 900 V PowiGaN-based ...
[73]
Two-Stage Flyback Micro Inverter for Solar Power Conversion
Nov 9, 2020 · In this study, the micro inverter which is comprised by flyback converter and H-bridge sections is designed and analyzed in terms of reliability and efficiency.
[74]
Flyback Photovoltaic Micro-Inverter with a Low Cost and Simple ...
The single-stage flyback Photovoltaic (PV) micro-inverter is considered as a simple and small in size topology but requires expensive digital ...
[75]
[PDF] High Step-Up Ratio Flyback Converter With Active Clamp and ...
This converter uses an active clamp flyback topology with a voltage multiplier, designed for high step-up ratios, and interfaces low-voltage sources with the ...Missing: advantages | Show results with:advantages
[76]
PMP41117 reference design | TI.com - Texas Instruments
Discover our design for 65W dual USB Type-C® port power delivery charger featuring an integrated GaN converter for enhanced efficiency and compact design.
[77]
Highly Efficient Secondary-Resonant Active Clamp Flyback Converter
Jul 31, 2017 · Over 93% full-load efficiency was demonstrated at the worst case 90-V ac input and maximum full-load efficiency was 94.5%. Published in ...
[78]
Designing Isolated Flyback Converter Circuits: Transformer Design ...
May 12, 2016 · For compliance with safety standards, we need to ensure adequate insulation in terms of a creepage distance between the primary and secondary ...Missing: high | Show results with:high
[79]
[PDF] Demystifying Clearance and Creepage Distance for High-Voltage ...
The foundational standard for user safety in an insulation system is IEC 60664-1, which applies to systems up to 1.5 kVDC or 1 kVAC. IEC 60664-1 covers creepage ...Missing: flyback | Show results with:flyback
[80]
High Voltage Transformer Safety Design Requirements - Case Study
Feb 20, 2023 · From IEC61558-1 in Table 5 the necessary creepage is between 4.3-8.6mm. In this case linear interpolation between table values is permitted, ...Missing: converter | Show results with:converter