Fact-checked by Grok 2 weeks ago

Oedometer test

The oedometer test, also known as the one-dimensional test, is a standard laboratory procedure in that evaluates the and properties of saturated cohesive s, such as clays and silty clays, by applying incremental vertical loads to a confined soil sample and measuring its deformation over time. This test simulates the gradual expulsion of pore water from soil under sustained loading, providing essential data for predicting long-term in structures like foundations, embankments, and dams. Developed around 1910 by French civil engineer Jean Frontard and later refined through the foundational work of Karl Terzaghi in 1919, the oedometer test has become a cornerstone of , standardized by organizations such as ASTM D2435 and AASHTO T 216 to ensure consistent and repeatable results. The apparatus, called an oedometer or consolidometer, typically consists of a rigid metal ring that confines the sample laterally to enforce one-dimensional compression, porous stones at the top and bottom for , and a loading mechanism such as a or pneumatic frame that applies controlled vertical stresses ranging from low initial values (e.g., 6.25 kPa) to higher increments (up to 800 kPa or more). In the procedure, an undisturbed or remolded sample—usually 50-100 mm in diameter and 20 mm thick—is trimmed to fit the ring, saturated if necessary, and subjected to successive load doublings while deformation is recorded using a dial gauge or (LVDT) at regular intervals until primary is complete for each increment, often over 24 hours. Key parameters derived from the test include the compression index (), which quantifies the 's change with ; the coefficient of consolidation (cv), indicating the rate of settlement; the (σ_p'), representing the maximum past stress the has experienced; and the swell index () during unloading phases. The test's significance lies in its ability to inform geotechnical designs by distinguishing between normally consolidated and overconsolidated soils, thereby enabling accurate calculations of both the magnitude and time rate of to prevent structural failures in compressible deposits. Advanced variants, such as thermo-hydro-mechanical oedometers, extend its application to study temperature and suction effects, but the standard test remains indispensable for routine soil characterization in projects.

Fundamentals

Definition and Purpose

The oedometer test, also known as the one-dimensional test, is a standard laboratory method in used to determine the magnitude and rate of of specimens. It involves applying incremental vertical loads to a saturated, fine-grained sample confined within a rigid ring to prevent , while allowing axial to measure vertical deformation over time. This controlled compression simulates the behavior of under sustained loading conditions, providing essential data on how the compresses as excess pore water pressures dissipate. The primary purpose of the oedometer test is to assess compressibility parameters, such as the index and coefficient of , which are critical for predicting long-term settlements in projects. By quantifying the 's response to loading, the test enables accurate estimation of and settlements in structures like foundations, embankments, and dams constructed on compressible deposits, thereby informing design decisions to mitigate excessive deformation. It particularly focuses on primary , the phase where settlement results from the expulsion of pore water under constant increase, helping engineers evaluate the time-dependent nature of behavior in the field. At its core, the oedometer test relies on Terzaghi's principle of effective stress and his one-dimensional consolidation theory, which explains consolidation as a process governed by the gradual dissipation of excess pore pressures through drainage paths, leading to volume reduction primarily in saturated clays. This theory assumes that soil deformation occurs solely due to changes in effective stress borne by the soil skeleton, with the rate controlled by soil permeability and drainage boundaries. In practice, the test's results support settlement analysis for clayey soils, where primary consolidation can extend over months or years, and aid in the design of infrastructure on soft ground to ensure stability and serviceability.

Theoretical Basis

The oedometer test elucidates the process in saturated , which proceeds via two primary mechanisms: primary and secondary . Primary arises from the dissipation of excess induced by an applied load, resulting in an increase in borne by the skeleton and consequent volumetric through expulsion of . Secondary occurs subsequently under sustained , driven by gradual particle rearrangement and creep-like deformation within the . Terzaghi's one-dimensional theory forms the cornerstone for analyzing primary in the oedometer test, positing that volume changes stem directly from the time-dependent increase in on the as excess pressures dissipate. This theory models the as a where total stress remains constant during drainage, with \sigma' defined as \sigma' = \sigma - u, where \sigma is total stress and u is ; the dissipation of u thus transfers load to the , compressing it vertically. The theory incorporates several simplifying assumptions to facilitate analytical solution: the soil sample is fully saturated with incompressible and grains, deformations are (neglecting higher-order effects), the soil skeleton exhibits linear behavior, and lateral are zero due to the rigid confining ring of the oedometer apparatus. These assumptions enable derivation of the governing for excess pore pressure u: \frac{\partial u}{\partial t} = c_v \frac{\partial^2 u}{\partial z^2} where z is the vertical coordinate through the sample thickness and t is time. The consolidation coefficient c_v, which dictates the rate of pressure dissipation and settlement, emerges from equating water outflow (via Darcy's law, v = k i, with hydraulic gradient i = -\partial u / \partial z) to the rate of volume change in the soil skeleton (governed by compressibility). Specifically, c_v = \frac{k}{\gamma_w m_v} where k is the soil's coefficient of permeability, \gamma_w is the unit weight of water, and m_v is the coefficient of volume compressibility, defined as m_v = -\frac{1}{1+e_0} \frac{\Delta e}{\Delta \sigma'} (with e_0 as initial void ratio and \Delta e / \Delta \sigma' as the change in void ratio per effective stress increment). This relation underscores how permeability controls drainage speed while compressibility dictates the magnitude of strain for a given stress change. In the oedometer context, consolidation settlement is distinct from immediate elastic settlement, which manifests instantaneously upon loading in a nearly undrained state without significant pore pressure dissipation, primarily in coarser soils or under rapid loading.

Historical Development

Origins and Invention

The oedometer test, a fundamental tool in for assessing , was developed around 1910 by French civil engineer Jean Frontard (1884–1962). Frontard's invention addressed the pressing need to evaluate soil behavior under controlled conditions, particularly in response to slope instabilities observed in earthen structures. This apparatus emerged during a period when geotechnical investigations were advancing to prevent structural failures in civil works. The primary motivation for the oedometer stemmed from the requirement to quantify compression and following notable earthen dam and dike incidents in late 19th- and early 20th-century . Frontard's work was informed by analyses of failures like the 1909 Charmes reservoir dike incident, where he investigated behavior to improve embankment . Frontard, tasked with analyzing such events, sought a method to simulate vertical loading on samples, replicating field conditions to predict long-term and in dams and foundations. This approach allowed engineers to move beyond empirical observations toward measurable parameters of , directly informed by real-world disasters like the Charmes . Frontard's initial design featured a basic fixed-ring oedometer, consisting of a rigid metal to confine undisturbed samples—typically thin cylinders about 5 thick and 35 in —subjected to incremental vertical loads via a simple dead-weight system. This setup ensured one-dimensional drainage and compression, isolating the effects of on void ratio without , providing early insights into processes. The economical frame design facilitated practical use in laboratories, marking a shift toward standardized testing. Frontard's pioneering experiments and findings were first detailed in early 20th-century publications within , including reports on experiments with sands and clays conducted in 1910 alongside collaborator Jacquinot on samples from failing . His 1914 account of the Charmes dike failure detailed soil analyses and recommendations for improving stability, influencing subsequent geotechnical practices.

Evolution and Standardization

The term "oedometer" derives from the Greek words oidéō (to swell) and metron (measure), referring to the measurement of swelling or . In the 1920s and 1930s, Karl Terzaghi advanced the oedometer test by incorporating it into his foundational consolidation theory, initially outlined in 1923 and detailed in his 1925 publication Erdbaumechanik, which enabled quantitative analysis of dissipation and time-dependent in saturated soils. These refinements transformed the test from a basic tool into a cornerstone for predicting long-term behavior, with Terzaghi's experimental validations emphasizing the role of paths and principles. Standardization of the oedometer test accelerated in the late , with ASTM D2435—covering one-dimensional properties using incremental loading—first published in 1965 and revised to incorporate precise procedures for magnitude and rate of settlement estimation. Complementing this, ASTM D4546, which addresses swell or settlement potential in cohesive soils under wetting-induced conditions, was established in 1985, providing methods for free swell, swell pressure, and collapse measurements. International equivalents followed, notably ISO/TS 17892-5 in 2004 (updated as ISO 17892-5:2017), which specifies incremental loading protocols for , swelling, and characteristics in a laterally confined setup. In the 2000s, oedometer testing evolved with the integration of digital data logging systems, enabling automated recording of displacement and load over time for enhanced accuracy in time-settlement curves and monitoring of processes. These updates, often featuring USB-connected dial gauges and software like GDSLAB for closed-loop control, minimized and supported advanced analyses such as constant rate of strain testing.

Equipment and Setup

Key Components

The oedometer apparatus consists of several essential components designed to simulate one-dimensional under controlled conditions. At the core is the , which includes a rigid metal ring, also known as the confining ring, typically constructed from or with diameters ranging from 50 to 100 mm. This ring encases the sample to prevent any or expansion, ensuring that deformation occurs solely in the vertical direction. Positioned at the top and bottom of the sample within the cell are porous stones, usually made of sintered or materials, which permit vertical of pore water while providing to the specimen. The loading system applies incremental vertical stresses to the sample, commonly reaching up to 1600 kPa to replicate field pressures. Traditional setups employ a lever-arm with counterweights, often at ratios such as 9:1 or 10:1, to multiply applied loads efficiently, while modern variants use hydraulic jacks or pneumatic loaders for precise control. , or vertical deformation, is measured using a dial gauge or (LVDT), offering accuracy to 0.001 mm for detecting minute changes in sample height. Additional accessories enhance the apparatus's functionality for specific test requirements. A saturator, often a water reservoir connected to the cell, facilitates sample wetting and saturation prior to loading by allowing upward or back-pressure water flow. A water jacket surrounding the cell maintains consistent temperature during testing to minimize thermal effects on consolidation. Counterweights provide the necessary loading increments in manual systems, and pneumatic loaders offer automated pressure application in advanced configurations. Standard oedometer samples adhere to dimensions that promote uniform stress distribution, with a typical height of 20 mm and a diameter-to-height ratio of 2:1, ensuring reliable representation of soil behavior as per established geotechnical standards.

Assembly and Calibration

The assembly of the oedometer begins with preparing the porous stones by saturating them in distilled water, either by boiling for 15 minutes or submerging for 4-8 hours, to ensure proper drainage functionality. The bottom porous stone is placed on the base of the consolidation cell, followed by a filter paper directly on the stone to prevent soil migration while allowing water passage; the metal confining ring is then positioned over this assembly. A top porous stone is installed above the ring (prior to sample insertion), with another filter paper placed between the stone and the eventual sample location, and the loading cap or pressure pad is centered on the upper stone to distribute loads evenly. The complete cell assembly is mounted onto the loading frame, ensuring axial alignment to avoid eccentric loading, and the displacement transducer, such as a dial gauge or linear variable differential transformer (LVDT), is attached to the loading cap for precise vertical deformation measurement. Calibration of the oedometer ensures accurate load and deformation measurements, starting with verification of load application linearity using a calibration disk made of high-strength metal, such as , with dimensions matching the soil sample (e.g., same and of approximately 20 ), to account for apparatus . The cell is assembled with the disk in place of the sample, moist porous stones, and no filter papers; a seating load is applied, followed by incremental loading up to the maximum test load (e.g., 64 kg for lever-arm systems) and unloading cycles repeated at least three times to exercise the equipment and record dial gauge deflections after 1-minute stabilization per increment. Dial gauge zero and span are checked by ensuring the spindle moves freely without sticking, returns to zero under no load, and spans accurately across its range using known or by comparing deflection plots from multiple runs for consistency; corrections for incremental deformations are calculated and applied to subsequent test data. Drainage paths are verified as unobstructed by inspecting porous stones for clogs and confirming water flow during , with the cell filled to cover the top stone. Common standards for assembly and calibration follow ASTM D2435, which specifies tolerances such as ring out-of-roundness less than 0.1% and flatness of ring ends within 0.01 mm to maintain uniform confinement, along with annual calibration of the loading system using a metal disk. during assembly and calibration is maintained at 20-25°C to minimize thermal effects on measurements, as recommended in geotechnical protocols aligned with ASTM guidelines. Lever-arm oedometers require of the lever ratio (e.g., 9.62 for 70-mm specimens) and inclusion of miscellaneous masses like the loading cap in stress calculations. Troubleshooting during assembly and calibration addresses common issues like friction in lever arms by balancing the load beam to offset the cell, disk, and gauge weights before loading, and performing multiple load-unload cycles to reduce ; if deflections vary between runs, the equipment is realigned or lubricated as needed. For porous stone permeability, stones are tested separately by measuring water flow under a known head or replaced if saturation does not achieve full drainage within expected times, ensuring no obstruction affects rates.

Test Procedure

Sample Preparation

The preparation of soil samples for the oedometer test is critical to ensure the specimen remains as undisturbed as possible, preserving its in-situ and for accurate measurement of behavior. Undisturbed samples are typically obtained from boreholes using thin-walled samplers such as the Shelby tube or piston samplers, which minimize disturbance during extraction, particularly for cohesive s like clays. Once retrieved, the sample is extruded from the sampler tube onto a stable surface, such as a plate covered with wax paper to prevent and loss. The specimen is then trimmed to fit the precise dimensions of the oedometer ring, usually using a , , or trimming for vertical sides and a for flat top and bottom surfaces, ensuring the diameter-to-height ratio is at least 2.5 (height-to-diameter ratio no greater than 1:2.5). During trimming, the sample is kept covered with plastic sheeting or maintained in a high-humidity to preserve content and prevent or cracking. To achieve full initial saturation, the trimmed specimen is placed between saturated porous stones with filter paper on both ends to facilitate drainage, and a low seating load—typically 1 to 5 kPa—is applied to seat the sample without inducing significant consolidation. The assembly is then flooded with de-aired water, and the load is maintained for at least 24 hours to allow any entrapped air to dissipate and ensure the degree of saturation approaches 100%, with the initial void ratio calculated from measurements of water content and specific gravity obtained from trim trimmings. Quality assurance involves visual inspection of the specimen for cracks, layering disruptions, or edge imperfections that could indicate disturbance, along with determination of initial and mass to verify uniformity. Remolded or reconstituted samples are generally avoided for standard consolidation testing, as they do not replicate the fabric and bonding of undisturbed , leading to unreliable results.

Loading Sequence and Measurements

The oedometer test utilizes an incremental loading procedure in which vertical stresses are applied successively in a , typically doubling with each increment to simulate field loading conditions. Common starting loads range from 5 to 25 kPa, progressing to 50, 100, 200, 400, and 800 kPa or higher as required by the soil type and anticipated in-situ stresses, with the maximum load selected to cover anticipated field stresses, typically extending to several times the . Each load increment is held constant until primary is nearly complete, generally for a duration of 24 hours or until 90-100% of primary consolidation has occurred based on diminishing rates. Settlement measurements are taken throughout each loading stage to capture deformation as a function of time, with initial readings recorded at short intervals such as 0.25, 0.5, 1, 2, 4, 8, 15, 30, and 60 minutes after load application, followed by readings at 2, 4, 8, and 24 hours. The end of primary for each increment is identified using semi-graphical methods, including plots of settlement versus the of time or versus the logarithm of time, where the cessation of the primary phase is marked by a change in the curve's slope indicating the onset of secondary . Unloading and reloading cycles are optionally incorporated after reaching the maximum load to evaluate swell potential or recompression behavior, with loads reduced in reverse sequence (e.g., from 800 kPa back to 400, 200, 100, and 50 kPa) and held for similar durations as during loading. The overall test duration typically ranges from one to two weeks, depending on the number of load increments, permeability, and inclusion of unloading phases. Data logging during the test involves either manual recording with a dial gauge or automated systems using linear variable differential transformers (LVDTs) or similar transducers, with measurements captured at intervals of 1 to 60 minutes to track settlement progression and detect the transition to secondary consolidation.

Data Analysis

Consolidation Curve

The consolidation curve in the oedometer test is constructed by plotting the void ratio (e) on the vertical axis against the logarithm of the effective vertical stress (log σ') on the horizontal axis, using data obtained from the primary consolidation phase of the test. This semi-logarithmic scale is employed because, for normally consolidated clays, the relationship between void ratio and effective stress exhibits linearity in this format over a range of stresses. The curve typically features two distinct segments: the recompression line, which has a flatter slope representing elastic rebound and reloading behavior at stresses below the preconsolidation pressure, and the virgin compression line, which is steeper and indicates irreversible plastic deformation at higher stresses. The preconsolidation pressure (σ'_p) is identified at the intersection point where the curve transitions from the recompression to the virgin compression line. To determine σ'_p, Casagrande's method involves locating the point of maximum curvature on the virgin compression portion of the e-log σ' curve, drawing a tangent line at that point and a horizontal line through that point, then constructing the bisector of the angle formed by these lines; the intersection of the bisector with the virgin compression line defines σ'_p. For noisy data arising from measurement variations, the curve may require smoothing through techniques such as fitting a sigmoid model to reduce artifacts and enhance interpretability. A typical e-log σ' for a normally consolidated clay sample, such as a soft marine clay, begins with a nearly horizontal recompression segment at low stresses (e.g., up to 50 kPa), followed by a sharp transition and a linear virgin region with a corresponding to the compression index, extending to higher stresses like 400 kPa, illustrating the soil's compressibility under increasing load.

Calculation of Parameters

The oedometer test yields data on versus and deformation versus time, from which key parameters are calculated to characterize and behavior. These parameters include the compression for virgin , the coefficient of for primary rates, the indicating past stress history, the secondary compression for long-term , and the coefficient of volume for volume change under load. Calculations typically involve graphical of the e-log σ' plot for stress-related parameters and the deformation-log time or deformation-square root time plots for time-dependent ones, following standardized procedures to ensure reproducibility. The compression index (Cc) quantifies the slope of the virgin compression portion of the (e) versus logarithm of effective vertical stress (log σ') curve, representing the soil's under loads exceeding the . It is calculated as the negative change in divided by the change in log σ', using data points from the linear segment of the virgin curve: C_c = -\frac{\Delta e}{\Delta \log \sigma'} For example, consider test data points on the virgin curve at σ' = 100 kPa (e = 1.0) and σ' = 400 kPa (e = 0.6); here, Δlog σ' = log(400/100) = 0.602 and Δe = 0.6 - 1.0 = -0.4, yielding Cc = 0.4 / 0.602 ≈ 0.66, indicating moderate typical of silty clays. This parameter is essential for predicting total primary in normally consolidated soils. The coefficient of consolidation (Cv) measures the rate of primary and is derived from the time-settlement curve for a given load increment, often using the Casagrande logarithm-of-time . In this approach, deformation is plotted against log time to identify the time (t50) corresponding to 50% of primary , with the path H typically as half the specimen thickness for double (H = H_dr). The formula is: C_v = \frac{T \cdot H^2}{t_{50}} where T = 0.197 is the time factor for 50% . For a 20 mm thick specimen (H_dr = 10 mm = 0.01 m) reaching 50% settlement at t50 = 1000 seconds, Cv = (0.197 × (0.01)^2) / 1000 ≈ 1.97 × 10^{-8} m²/s, a value indicative of slow-draining clays. Alternatively, the Taylor square-root-of-time uses t90 for 90% with T = 0.848, but the log-time is preferred for its accuracy in identifying phases. The preconsolidation pressure (σ'p) represents the maximum past experienced by the soil and is determined graphically from the e-log σ' curve using the Casagrande method, which identifies the transition from recompression to virgin compression. The involves: (1) plotting the curve, (2) identifying the point of maximum curvature on the virgin portion, (3) drawing a at that point and a line through that point, and (4) finding the of the angle bisector with the virgin compression line to read σ'p. For overconsolidated soils, the recompression index (Cr) from the initial curve segment relates to Cc by Cr/Cc ≈ 1/5 to 1/10, aiding in verifying the break point. This method, while subjective, remains the standard for estimating soil stress history in analyses. The secondary compression index (Cα) describes the creep behavior after primary consolidation ends and is calculated as the slope of the linear portion of the void ratio versus log time curve in the secondary phase: C_\alpha = -\frac{\Delta e}{\Delta \log t} This parameter captures time-dependent volume reduction due to particle rearrangement, typically measured over a log time interval beyond t90. For peats or organic soils, Cα values range from 0.01 to 0.06, contributing significantly to long-term settlements exceeding primary amounts. The coefficient of volume compressibility (mv) expresses the change in volume per unit initial volume per unit increase in and is computed for each load increment as: m_v = -\frac{\Delta e}{(1 + e_0) \Delta \sigma'} where e0 is the initial . Using the earlier Cc example with Δe = -0.4, e0 = 1.0, and Δσ' = 300 kPa, mv ≈ 0.4 / (2 × 300) = 6.67 × 10^{-4} m²/kN, useful for immediate estimates in overconsolidated soils. This parameter integrates both and volumetric responses under confined conditions.

Applications and Limitations

Practical Uses

The oedometer test plays a crucial role in predicting long-term settlements of on compressible soils by providing key parameters such as the compression index (C_c) and coefficient of (C_v), which are integrated into Terzaghi's one-dimensional . These parameters enable engineers to calculate primary using the formula S_c = \frac{C_c H_0}{1 + e_0} \log\left(\frac{\sigma'_0 + \Delta\sigma'}{\sigma'_0}\right), where H_0 is the initial layer thickness, e_0 is the initial , \sigma'_0 is the initial , and \Delta\sigma' is the increase due to the load. For time-dependent predictions, C_v is used to determine the degree of U = f(T_v), with T_v = \frac{C_v t}{H_{dr}^2}, allowing estimation of over extended periods such as 50 years under a building on soft clay, where partial might still occur based on site-specific paths. In geotechnical design, oedometer-derived parameters inform the stability and performance of by predicting settlements under staged loading, enabling preload designs to achieve 95-98% prior to permanent construction. For instance, indices from oedometer tests guide finite element modeling to optimize embankment heights and durations, reducing post-construction settlements in soft soils. Similarly, in landfill liner design, these tests assess primary and secondary of underlying soils to ensure the integrity of engineered barriers under waste loads, with parameters like and C_c used to model differential settlements affecting and systems. For pile load tests, oedometer results integrate with site investigation data to estimate settlements around pile groups, supporting evaluations in compressible strata. Case studies highlight the test's application in challenging soft clay environments. In Boston's geotechnical projects involving Blue Clay, oedometer consolidation data from resedimented samples at overconsolidation ratios of 1 to 4 informed undrained strength assessments, aiding foundation designs for urban infrastructure on historically compressible deposits. Likewise, in reclamation efforts, oedometer tests on clays with initial void ratios around 2.4 and compression parameters such as λ = 0.36 revealed thermal-dependent creep behaviors, enabling numerical models to predict long-term settlements for port and coastal developments. Oedometer tests are often paired with triaxial tests to provide a comprehensive view of soil behavior, where oedometer data on and complement triaxial measurements of undrained under K_0 consolidation conditions, particularly for overconsolidated clays in site characterization. This integration minimizes sample disturbance effects and supports holistic designs by linking one-dimensional settlement predictions with multi-directional shear parameters.

Sources of Error and Variations

The oedometer test is susceptible to several sources of error that can compromise the accuracy of consolidation parameters. Sample disturbance, arising from , transportation, trimming, and placement of the specimen, alters the 's fabric and history, leading to underestimation of the (σ'p) and errors in the compression index (Cc). This disturbance is particularly pronounced in sensitive clays, where even minor handling can change the curve significantly. Friction between the specimen and the confining , often referred to as side or wall , induces non-uniform distribution within the sample, especially in tests with high height-to-diameter ratios. This effect can underestimate the measured and distort the curve, with errors more evident in stiffer soils. Determination of the (σ'p) is particularly sensitive to these errors, as slight disturbances can obscure the characteristic break in the void ratio-effective curve, leading to inaccurate identification via methods like Casagrande's. Additionally, the test's assumption of instantaneous at the porous boundaries may not hold if filters clog or partial occurs, resulting in underestimation of the coefficient of (cv). Key limitations of the standard oedometer test stem from its strict one-dimensional (1D) strain assumption, which enforces zero and is unsuitable for granular soils like sands, where rapid and particle rearrangement dominate over . The test also inadequately captures in natural soils, as it assumes isotropic behavior, potentially underpredicting settlements in layered or directionally varied deposits. Furthermore, short-duration tests often overlook (secondary ), which becomes significant over long timescales in fine-grained soils. To address these issues, several variations of the oedometer test have been developed. The constant rate of strain (CRS) oedometer applies a continuous axial while measuring directly, enabling faster testing (often in hours rather than days) and better resolution of stress-strain relationships without relying on time-settlement curves. The Rowe cell, a hydraulic consolidation apparatus, permits radial drainage and variable lateral stress control, simulating two-dimensional (2D) conditions more representative of field scenarios like embankments. Hydraulic oedometers, equipped with high-capacity loading systems, extend the pressure range to several megapascals, suitable for testing stiff or overconsolidated soils under extreme loads. Improvements to mitigate errors include the use of high-quality samplers, such as fixed-piston or block samplers, which minimize disturbance during retrieval by reducing shear and maintaining stress states. Numerical corrections, such as the Schmertmann method, adjust the measured compression curve by estimating the degree of disturbance based on void ratio changes and reconstructing the undisturbed curve for more reliable parameter estimation.