Fact-checked by Grok 2 weeks ago

XAUI

XAUI, or 10 Gigabit Attachment Unit Interface, is a high-speed serial electrical interface specified in Clause 47 of the IEEE 802.3-2002 standard (Amendment IEEE 802.3ae) for 10 Gigabit Ethernet, designed to extend the parallel XGMII (10 Gigabit Media Independent Interface) between the media access control (MAC) layer and the physical layer (PHY), or between PHY components, enabling reliable chip-to-chip or module-to-module connections over distances up to approximately 1 meter using copper cabling.^[1] Defined as part of the IEEE 802.3 protocol extension to support 10 Gb/s operation, XAUI reduces the pin count required for high-speed interconnects—from the 74 signals of XGMII to just 8 differential pairs—by serializing data across four independent lanes, each operating at a line rate of 3.125 GBaud (equivalent to 3.125 Gb/s after 8B/10B encoding) with a bit error ratio not exceeding 10⁻¹².^[1]^[2] This interface employs AC-coupled differential PECL signaling with specific electrical characteristics, including a differential output amplitude below 1600 mV peak-to-peak, output impedance greater than 38 Ω, and return loss defined by Equation 47-1 in the standard, ensuring robust performance in short-reach applications such as backplanes or direct-attach cables.^[1] XAUI's structure includes a gearbox for mapping the 32-bit parallel XGMII data and 4-bit control signals across the four lanes (labeled 0 through 3), with each lane carrying serialized 8B/10B encoded code-groups for DC balance, clock recovery, and error detection; alignment and synchronization are achieved using special control characters like /A/, /K/, and /R/, while deskew and clock tolerance compensation handle up to 4096 bit times of round-trip delay.^[1] It integrates with the 10GBASE-X physical coding sublayer (PCS) in Clause 48, supporting variants like 10GBASE-SR, 10GBASE-LR, and 10GBASE-CX4, and has been incorporated into subsequent amendments, including the IEEE 802.3-2012 consolidation for ongoing compatibility in Ethernet ecosystems.^[1]^[2] Primarily used in enterprise networking, storage area networks, and high-performance computing for low-latency, high-bandwidth links, XAUI paved the way for later multi-lane interfaces like those in 40G/100G Ethernet while remaining a foundational element for 10 Gb/s PHY implementations.^[1]^[3]

Introduction and Background

Definition and Purpose

XAUI, or 10 Gigabit Attachment Unit Interface (pronounced "zowie"), is a high-speed electrical interface defined in Clause 47 of the IEEE 802.3ae-2002 standard for 10 Gigabit Ethernet (10GbE). The name derives from the Roman numeral "X" denoting ten and the legacy Ethernet Attachment Unit Interface (AUI), reflecting its role as an evolution of earlier Ethernet interconnects. It serves as an optional, self-clocked serial bus that interconnects two XGMII Extender Sublayers (XGXS) to facilitate 10 Gb/s data transmission within systems.^[4] The primary purpose of XAUI is to extend the operational reach of the XGMII (10 Gigabit Media Independent Interface), which is limited to short distances of approximately 7 cm over board traces due to electrical constraints. XAUI achieves this by enabling chip-to-chip or chip-to-module connections over longer distances, typically up to 50 cm on controlled-impedance printed circuit boards (PCBs), while maintaining compatibility with 10GbE protocols. This extension supports greater flexibility in system design, such as backplane or module interconnections, without requiring external cabling for intra-system links.^[5] XAUI reduces the interface pin count from 74 signals in the parallel XGMII to just 16 pins by serializing the data path into four differential lanes—eight pairs total for transmit and receive. Each lane operates at a nominal rate of 3.125 Gb/s using 8B/10B encoding, aggregating to a total throughput of 10 Gb/s. This serialization minimizes interconnect complexity and signal integrity challenges, making XAUI suitable for short-range, high-speed applications within 10GbE equipment.^[6]

Historical Development

XAUI, or 10 Gigabit Attachment Unit Interface, evolved from the concept of the Attachment Unit Interface (AUI) originally introduced in early Ethernet standards such as IEEE 802.3 for 10BASE5, which provided a standardized way to connect media access units to transceivers, but was adapted for high-speed serial links in 10 Gigabit Ethernet (10GbE) to address the limitations of parallel interfaces. This evolution aimed to extend the reach and reduce complexity compared to predecessor interfaces like the 10 Gigabit Media Independent Interface (XGMII), serving as a low-pin-count serial alternative with four lanes operating at 3.125 Gbps each.^[5] The development of XAUI was undertaken by the IEEE 802.3ae Task Force, which began work in March 1999 following the Higher Speed Study Group and Project Authorization Request, culminating in the standard's completion by 2002 to support initial 10GbE deployments over fiber and copper media.^[7] The standard was approved by IEEE RevCom on June 12, 2002, and published as IEEE Std 802.3ae-2002 on August 30, 2002, defining XAUI in Clause 47 as an optional chip-to-chip interface for 10 Gb/s operation.^[1] It was later incorporated into the consolidated IEEE 802.3-2008 standard, which included minor clarifications to the physical coding sublayer and electrical specifications without altering core functionality.^[8] XAUI's design was primarily driven by the need for a cost-effective, low-pin-count solution—reducing the 74 signals of XGMII to 8 differential pairs (16 pins)—facilitating integration in application-specific integrated circuits (ASICs) and field-programmable gate arrays (FPGAs) for 10GbE systems.^[9] Key milestones included the task force's progression through drafts from 1999 to 2002, with early interoperability demonstrations in 2003, such as those by Vitesse and Xilinx at the Optical Fiber Communication Conference, enabling adoption in commercial products like Fujitsu's single-chip 10GbE switches.^[10]^[11] By 2025, XAUI remains a legacy interface, still supported in intellectual property (IP) cores from vendors including AMD (formerly Xilinx) and Synopsys for backward compatibility in 10GbE designs, though it has been largely superseded by higher-speed interfaces like CAUI for 40 Gb/s and 100 Gb/s Ethernet applications.^[3]^[12]^[13]

Technical Specifications

Physical Layer Characteristics

XAUI employs four differential lane pairs, designated TX0–TX3 for transmission and RX0–RX3 for reception, enabling full-duplex operation at 10 Gbps aggregate throughput.^[14] Each lane operates independently at a serialized rate of 3.125 Gbps, incorporating 8b/10b encoding overhead to deliver a 10 Gbps payload across the four lanes.^[14]^[5] The interface utilizes current mode logic (CML) differential signaling with a differential peak-to-peak voltage swing greater than 600 mV and less than or equal to 1600 mV (typically 800 mV), ensuring compatibility across AC-coupled connections while minimizing electromagnetic interference.^[14]^[15] Transmission occurs over controlled-impedance traces with a 100 ohm differential impedance, supporting reaches of up to 50 cm over controlled-impedance traces or 20 cm on standard FR4 printed circuit boards.^[14]^[5] The pinout consists of 16 total pins—eight for transmit (four differential pairs) and eight for receive—eliminating the need for a forwarded clock through the use of embedded clock recovery at the receiver.^[16]^[17] Power consumption in typical implementations ranges from 1 to 2 W per port.^[18]^[14]

Encoding and Data Path

XAUI employs 8b/10b encoding on each of its four lanes to convert 8-bit data or control characters into 10-bit symbols, ensuring DC balance for reliable transmission and facilitating clock data recovery at the receiver.^[19] This encoding scheme introduces a 20% overhead, as only 8 of the 10 bits carry payload information, while the additional bits support disparity management—particularly during idle sequences—to maintain running disparity and prevent signal baseline wander.^[6] Disparity errors in the 8b/10b decoding process signal potential link faults, such as transmission impairments, and are propagated as error indicators to higher layers.^[19] The data path begins with the 32-bit XGMII (10 Gigabit Media Independent Interface) input, which is striped across four 8-bit lanes in a columnar fashion to preserve alignment, with each lane then serialized after 8b/10b encoding.^[19] This mapping reduces the interface complexity from XGMII's 74-pin width (including data, control, and clock signals) to XAUI's narrower 16-pin differential structure, enabling higher-speed operation over backplanes up to 50 cm.^[20] The aggregate raw bandwidth across the four lanes reaches 12.5 Gbps (4 × 3.125 Gbps per lane), accounting for the encoding overhead to deliver the required 10 Gbps Ethernet payload throughput.^[6] Control characters from XGMII, such as /S/ for start-of-packet, /T/ for terminate, and /I/ for idle, are mapped to specific 8b/10b K-codes for transmission, with K28.5 serving as the comma alignment delimiter to enable word synchronization on each lane.^[19] During initialization, lane synchronization relies on alignment markers incorporating D21.5 (0xBC), which help deskew the lanes by up to 40 bit times and establish column alignment across the four paths.^[19]

Operation and Functionality

Transmit Operations

The transmit operations of XAUI begin with the reception of 32-bit parallel data from the XGMII interface, accompanied by 4-bit control signals that indicate data validity, start-of-frame, end-of-frame, or idle states, operating at a 156.25 MHz clock rate to achieve an aggregate 5 Gbps throughput across four logical lanes.^[21] This input is processed by the XAUI PCS (Physical Coding Sublayer) to prepare it for serialization over the physical lanes.^[19] The core of the transmit process involves a gearbox that aggregates the 32-bit XGMII data into four 8-bit streams, one per XAUI lane, before applying 8b/10b encoding to convert each 8-bit data nibble (plus control) into a 10-bit code group, ensuring DC balance and clock recovery while expanding the bit rate to 3.125 Gbps per lane for a total of 12.5 Gbps serialized output.^[22] These 10-bit code groups are then serialized by the PMA (Physical Medium Attachment) sublayer using differential CML signaling.^[21] Lane mapping assigns the parallel data sequentially: bits 0-7 to lane 0, 8-15 to lane 1, 16-23 to lane 2, and 24-31 to lane 3, with start-of-packet delineation ensured by aligning control characters across lanes to maintain frame integrity during transmission.^[19] To compensate for clock tolerance variations between the XGMII and XAUI domains (up to ±100 ppm), idle insertion occurs by replacing XGMII idle patterns with /I/ ordered sets, specifically /K28.5/ comma characters for synchronization, /A/ (K28.3) for alignment, or /R/ (K28.0) for rate matching, inserted or suppressed as needed to pad inter-frame gaps without altering data content.^[22]^[21] Optional transmitter-side pre-emphasis or equalization adjustments are applied to the serialized signals to mitigate inter-symbol interference and attenuation over backplane traces up to 20 inches, with programmable de-emphasis levels (e.g., 10-30%) enhancing signal integrity for reliable reception.^[22] Link initialization commences with a training sequence where the transmitter sends continuous /K28.5/ comma alignment patterns across all four lanes to establish per-lane synchronization, followed by periodic /A/ ordered sets every 16 to 32 code groups for deskewing and verifying lane alignment, transitioning the link from an unsynchronized to a fully operational state once comma detection and skew correction are confirmed.^[19]^[21]

Receive Operations

The receive operations in XAUI begin with clock data recovery (CDR) for each of the four independent lanes, where the embedded clock is extracted from the incoming 3.125 Gbaud serial data stream using a phase-locked loop or similar mechanism to retime the signal. This process ensures synchronization despite potential clock frequency variations of up to ±100 ppm between the transmitter and receiver, as specified in IEEE 802.3ae Clause 48.^[21]^[22] The CDR operates on the differential receive signaling, providing a recovered clock that drives subsequent deserialization without requiring an external reference clock for each lane.^[19] Following clock recovery, the serial data undergoes 8b/10b decoding, which converts the 10-bit transmission characters back to 8-bit data or control characters while verifying running disparity and code validity. Invalid code groups, such as those failing disparity checks or not matching defined symbols, are detected and flagged, with the decoder outputting an error indicator instead of the presumed data to prevent propagation of corrupted information. This decoding leverages comma characters (K28.5 or K28.7) for symbol alignment within each lane, ensuring boundaries are correctly identified per Clause 36 of IEEE 802.3ae.^[21]^[22] Disparity errors, arising from mismatched positive or negative running disparity across symbols, are particularly monitored to maintain DC balance and signal integrity.^[17] Deskewing addresses inter-lane timing differences by aligning the four deserialized streams using elastic buffers, typically FIFO structures with depths supporting up to 40 unit intervals (UI) of skew—equivalent to approximately 12.8 ns at 3.125 Gbaud—to compensate for propagation delays across the backplane or PCB traces. Alignment is achieved by detecting ordered set alignment characters (/A/ K28.3 symbols) transmitted periodically during idle periods, allowing each lane's buffer to delay or advance data until columns synchronize, as outlined in Clause 48.2.^[21]^[17] This automatic per-lane adjustment tolerates maximum skew variations without manual intervention, enhancing robustness in multi-lane environments.^[19] Once aligned, the lanes are reassembled into a 32-bit XGMII interface by interleaving the 8-bit data/control from each lane (bits 0-7 from lane 0, 8-15 from lane 1, etc.), discarding idle characters (/I/ K28.5 or K28.7 sequences) to form continuous data streams. The reassembly process maps control characters like start (/S/) and terminate (/T/) to XGMII control codes, ensuring seamless transition to the MAC layer.^[21]^[22] Concurrently, a gearbox performs deserialization and rate matching, inserting or deleting /R/ skip characters (K28.0) as needed to reconcile the ±100 ppm clock tolerance between the serial lanes and the parallel 156.25 MHz XGMII clock, preventing buffer overflow or underflow.^[19]^[17] Error handling integrates throughout these stages, detecting comma misalignment (failed /A/ detection across lanes) or disparity violations and signaling faults via XGMII control characters, such as /E/ for errors or /Q/ for remote faults. If any lane loses synchronization—due to persistent invalid codes or excessive skew—the entire XAUI link is declared faulty, halting data flow and notifying higher layers through status registers accessible via MDIO. This mechanism ensures reliable operation by isolating issues without compromising the overall 10 Gb/s throughput.^[21]^[22]

Variants and Extensions

RXAUI

RXAUI, or Reduced Pin eXtended Attachment Unit Interface, is a proprietary variant of XAUI designed to maintain 10 Gbps aggregate bandwidth while reducing the interface to two lanes operating at 6.25 Gbps each, thereby halving the high-speed pin count from 16 differential signals in XAUI to 8.^[23]^[24] This reduction addresses pin limitations in dense chip designs by aggregating data from four logical XAUI lanes into two physical lanes, requiring additional multiplexing logic for compatibility.^[25] Developed by Dune Networks, with interoperability demonstrated by partners including Vitesse Semiconductor and NetLogic Microsystems during the mid-2000s, RXAUI emerged as a non-standard extension to XAUI around 2005–2010 to enable shorter-reach, pin-efficient connections in Ethernet systems.^[26]^[27]^[28]^[29] It is not defined in the core IEEE 802.3 standard but supports interoperability with XAUI through adapters that handle lane remapping and code adjustments.^[29] In typical implementations, RXAUI lane 0 maps to XAUI lane 0 (carrying least significant bits) and RXAUI lane 1 maps to XAUI lane 2 (carrying most significant bits), with unused lanes powered down to minimize power and interference.^[24] The encoding retains XAUI's 8b/10b scheme but employs doubled serialization, where 16-bit data from two XAUI lanes is parallelized into two 8-bit streams per RXAUI lane for transmission at the higher rate.^[25] RXAUI achieves reach comparable to XAUI, supporting up to 50 cm (20 inches) on FR-4 backplanes plus connectors, though the elevated per-lane speed of 6.25 Gbps exacerbates signal attenuation and requires enhanced equalization in the serializer/deserializer (SerDes).^[25]^[24] Implementations are prevalent in field-programmable gate arrays (FPGAs), such as AMD/Xilinx LogiCORE IP cores for 7 Series and UltraScale devices, which integrate RXAUI with GT transceivers for low-latency multiplexing.^[23]^[25] It also appears in backplane physical layer (PHY) devices from vendors like Microchip (e.g., VSC8491) and Marvell (e.g., 88X2222), targeting pin-constrained applications in 10G Ethernet switches and routers.^[24]^[30]

DXAUI and Other Adaptations

DXAUI, or Dual XAUI, extends the standard XAUI interface by utilizing an 8-lane configuration to support 20 Gbps aggregate throughput, effectively combining two independent 10 Gbps XAUI links for applications such as aggregated backplanes in high-density networking equipment.^[3]^[31] This configuration employs eight serial lanes, each operating at 3.125 Gbps with 8B/10B encoding, allowing for scalable bandwidth in systems requiring doubled capacity without redesigning the core protocol.^[32] In practice, DXAUI is implemented in FPGAs and ASICs to facilitate backplane interconnections, where the dual-link aggregation reduces latency and enhances fault tolerance by isolating traffic across the two XAUI sets.^[3] Directional adaptations of XAUI appear in certain ASIC designs, featuring separate transmit (TX) and receive (RX) pinouts to optimize for unidirectional data flows in specialized networking topologies.^[33] These adaptations allow independent control of TX and RX paths, enabling configurations where one direction handles primary traffic while the other supports monitoring or auxiliary functions, as seen in PHY devices with distinct lane assignments for TX/RX operations.^[34] Such designs are particularly useful in backplane applications where signal integrity demands isolated pathways to minimize crosstalk between directions.^[35] The emerging xAUI-n interface, defined within the IEEE P802.3dj Task Force, represents a scalable evolution of XAUI for higher-speed Ethernet standards including 100 Gb/s, 200 Gb/s, 400 Gb/s, 800 Gb/s, and 1.6 Tb/s variants, supporting multi-lane configurations at elevated per-lane rates such as 10.3125 Gbps to accommodate 100/200/400/800 GbE and 1.6 Tb/s requirements.^[36] This adaptation maintains compatibility with xBASE-R encoding while introducing flexible lane counts (n lanes) for internal sublayers, such as between PMA blocks, to handle increased data rates in 800 Gb/s and 1.6 Tb/s systems.^[37] In drafts as of September 2025, xAUI-n supports test patterns like PRBS31Q and scrambled idle for validation, ensuring interoperability in advanced PHY transmitter testing.^[38]^[39] Adapter modules, including XAUI-to-RXAUI converters integrated into IP cores, provide backward compatibility for legacy systems transitioning to reduced-lane interfaces, folding four XAUI lanes into two RXAUI lanes at double the clock rate.^[29] These adapters, often implemented in FPGA or ASIC fabrics, handle lane interleaving and deskew to maintain 10 Gbps throughput while halving pin count, as specified in open-source and vendor designs.^[40] Legacy extensions of XAUI incorporate the SerDes Framer Interface (SFI) for integration with optical modules, enabling direct connectivity in 10 GbE transceivers that convert SFI serial inputs to parallel XAUI outputs for LAN/WAN applications.^[41] Devices like dual-channel SFI-to-XAUI PHYs support multimode fiber up to 300 meters and copper twin-ax cabling, bridging legacy optical standards with XAUI backplanes in enterprise switches.^[42] Multi-lane setups in DXAUI and xAUI-n introduce challenges including elevated power consumption due to additional transceivers and increased design complexity from lane synchronization and crosstalk mitigation.^[43] Power demands scale with lane count, often exceeding 1 W per lane in high-speed variants, while complexity arises in timing alignment across lanes, necessitating advanced equalization and deskew mechanisms.^[44] These issues are addressed through optimized SerDes architectures but remain critical in dense backplane deployments.^[45]

Applications and Implementations

Primary Use Cases

XAUI serves as a key interface for chip-to-chip interconnects in 10 Gigabit Ethernet (10GbE) switches, routers, and network interface cards (NICs), particularly enabling the separation between the media access controller (MAC) and physical layer (PHY) components to simplify board design and reduce pin counts.^[22] This application leverages XAUI's four-lane, 3.125 Gbps per lane architecture to achieve 10 Gbps aggregate throughput over short distances, facilitating high-density integration in networking hardware.^[46] For instance, Texas Instruments' TLK3114 transceiver implements XAUI for bidirectional point-to-point data transmission in such systems.^[22] In modular systems like blade servers, XAUI functions as a backplane interface, supporting connections between line cards and switch cards over distances up to approximately 50 cm on FR4 printed circuit boards.^[5] This capability makes it suitable for chassis-based architectures in enterprise and telecommunications equipment, where low electromagnetic interference (EMI) and built-in error detection via 8B/10B encoding ensure reliable operation across backplane traces.^[46] XAUI is widely employed in FPGA and ASIC prototyping for 10GbE testing and development, allowing rapid validation of high-speed Ethernet designs.^[47] Implementations in Xilinx Virtex-series FPGAs, such as Virtex-II Pro and Virtex-5, provide complete XAUI solutions including IP cores for seamless integration with 10GbE MACs, enabling engineers to prototype and debug systems efficiently.^[47]^[48] As of 2025, XAUI continues to support legacy 10GbE deployments in data centers, where it remains integral to existing switches and NICs amid ongoing market growth for 10GbE controllers at a 5.4% CAGR through 2031, though its adoption is declining relative to faster 25GbE and 40GbE standards driven by AI and cloud demands.^[49]^[50] NXP's QorIQ processors, such as the P4080, incorporate XAUI interfaces for these environments, often tested via dedicated risers.^[51] In test equipment, XAUI enables compliance verification for IEEE 802.3ae through pattern generators that produce standardized test sequences, such as those defined in Annex 48A for jitter and bit error rate (BER) assessment.^[5] Tools like the Agilent 71612C bit error rate tester drive XAUI inputs to evaluate device performance under conditions like high-frequency patterns, ensuring adherence to 10GbE specifications.^[5]

Design and Integration Considerations

When designing systems incorporating XAUI, printed circuit board (PCB) layout plays a critical role in maintaining signal integrity for the four-lane, 3.125 Gbps per lane interface. To minimize crosstalk, traces should maintain a spacing of at least five times the ground-plane gap between adjacent differential pairs, with a minimum of three times the gap, while routing all traces adjacent to a continuous ground plane to provide low-impedance return paths and reduce noise coupling.^[34] Trace length matching is essential to limit intra-pair skew, typically required within 30 mils (0.076 cm) for each differential pair, and inter-pair matching across lanes to prevent excessive deskew demands at the receiver.^[34] Additional measures include using 50 Ω single-ended (100 Ω differential) controlled-impedance traces in microstrip or stripline configurations, avoiding unnecessary vias, and placing AC coupling capacitors close to the receiver.^[34] Power supply requirements for XAUI implementations typically range from 2.3 V to 3.3 V, depending on the specific transceiver or PHY chip, with common operating voltages at 2.5 V for core logic and 3.3 V for I/O interfaces to ensure compatibility with IEEE 802.3ae specifications.^[22]^[19] Thermal management is particularly important in dense application-specific integrated circuits (ASICs) or field-programmable gate arrays (FPGAs) hosting XAUI, where power dissipation can reach several watts per channel; efficient heat dissipation requires maximizing thermal vias to ground planes and incorporating active cooling solutions such as heat sinks or forced-air systems to maintain junction temperatures below 85°C.^[34] In high-density designs, multiple ground planes further aid in distributing heat and stabilizing voltage rails.^[34] Interoperability between XAUI components demands rigorous compliance testing to ensure reliable operation across vendors. Key tests focus on skew tolerance, where receivers must handle up to 12.8 ns (40 UI) of total inter-lane skew (including contributions from transmitter, interconnect, and clock offsets) as per IEEE 802.3ae budgets, with deskew circuits in the physical coding sublayer (PCS) compensating for variations.^[52]^[17] Bit error rate (BER) performance is verified at less than 10^{-12} using stressed eye patterns and jitter injection, confirming the link's robustness under worst-case conditions like maximum deterministic jitter (up to 0.65 UI) and random jitter (0.10 UI).^[5]^[52] These tests, often conducted with bit error rate testers (BERTs), ensure alignment with clause 47 electrical specifications for differential signaling.^[19] Upgrading legacy 10 GbE systems to higher speeds like 40 GbE involves migration paths using adapters that bridge XAUI to XLAUI (extended XAUI for 40G) or CAUI (100G attachment unit interface) standards, leveraging the similar multi-lane architecture to minimize redesign.^[53] Such adapters, available from vendors like Intel and Microchip, perform rate adaptation and protocol mapping, enabling incremental upgrades in backplanes or chassis-based systems while preserving existing XAUI PHY investments.^[54] Cost considerations for XAUI integration favor electrical interfaces over optical transceivers, offering lower overall expenses due to reduced component count and simpler assembly, though they require more precise pin preparation compared to serial frontend interfaces (SFI).^[55] Licensing IP cores for XAUI PHY and PCS functions, such as those from Synopsys or Xilinx, typically involves project-based fees that can range from tens to hundreds of thousands of dollars, depending on volume and customization, making it a significant factor in ASIC development budgets.^[56] XAUI lacks built-in encryption at the physical layer, focusing instead on reliable data transmission; security for Ethernet frames is provided by higher-layer protocols like MACsec (IEEE 802.1AE) at the media access control (MAC) sublayer.

References

[1]
[PDF] IEEE Std 802.3ae-2002, Amendment to CSMA/CD
Aug 30, 2002 · Abstract: Support to extend the IEEE 802.3 protocol and MAC specification to an operating speed of. 10 Gb/s.
[2]
IEEE 802.3ae-2002 - IEEE SA
Support to extend the IEEE 802.3 protocol and MAC specification to an operating speed of 10 Gb/s. Several Physical Coding Sublayers known as 10GBASE-X, 10GBASE- ...
[3]
XAUI/DXAUI - AMD
The AMD 10 Gigabit Attachment Unit Interface (XAUI) LogiCORE™ IP provides a 4-lane high speed serial interface, providing up to 10 Gigabits per second (Gbps) ...
[4]
XFI-XAUI integrated circuit for use with 10GBASE-LX4 optical ...
... XAUI (pronounced “Zowie”) interface. The “AUI” portion of the acronym is borrowed from the Ethernet Attachment Unit Interface. The “X” in the acronym ...Missing: pronunciation | Show results with:pronunciation
[5]
[PDF] 10 Gigabit Ethernet and the XAUI interface - HPWiki
10 Gigabit Ethernet uses the IEEE 802.3 Ethernet Media. Access Control (MAC) protocol, the IEEE 802.3 Ethernet frame format, and the minimum and maximum IEEE ...
[6]
XAUI: Curing Internal Speed Blockages - EE Times
It won't be appearing on your desktop anytime soon, but the 10-Gbps attachment unit interface (XAUI, pronounced “Zowie”),promising 10-Gbps Ethernet speeds ...Missing: pronunciation | Show results with:pronunciation
[7]
[PDF] 8. Implementing 10-Gigabit Ethernet Using Stratix & Stratix GX Devices
Jul 3, 2005 · XAUI. XAUI (pronounced Zowie) is located between the XGMII at the reconciliation sublayer and the XGMII at the PHY layer. Figure 8–15 shows ...<|control11|><|separator|>
[8]
IEEE P802.3ae – 10 Gigabit Ethernet Minutes Task Force Plenary ...
Sep 14, 2000 · XAUI - Initialization protocol (ties to RF & BL), Remote Fault & Break Link transport, Signal Detect transport (medium to PCS). ❑. WIS ...
[9]
IEEE 802.3-2008 - IEEE SA
IEEE 802.3-2008 specifies Ethernet local area network operation from 1 Mb/s to 10 Gb/s using CSMA/CD, and is now a superseded standard.
[10]
The Case for DDR-XAUI - EE Times
Oct 12, 2007 · XAUI reduces 10 Gigabit Ethernet's 72 pin XGMII to 16 pins, enabling higher density and lower cost switching chips and optical transceivers. ...<|control11|><|separator|>
[11]
Vitesse and Xilinx Demonstrate OIF Interoperability Enabling ...
Vitesse and Xilinx Demonstrate OIF Interoperability Enabling 10Gbps Ethernet at OFC 2003. CAMARILLO, Calif. - March 24, 2003 - Vitesse Semiconductor ...
[12]
[PDF] Industry Leading 1/10/40 GbE Technology From Fujitsu Frontech
• Fujitsu developed the world's first single “10 Gigabit Ethernet Switch on a Chip” in. 2003. • Fujitsu switches pass packets fast and reliably which make them ...Missing: early | Show results with:early
[13]
Synopsys Announces Low Power PHY IP for PCI Express, XAUI and ...
The DesignWare SATA and XAUI PHYs are currently available in limited production for 130- and 90-nm process technologies. The DesignWare PHY for PCI Express is ...Missing: legacy AMD Xilinx
[14]
[PDF] 40 Gigabit Ethernet and 100 Gigabit Ethernet Technology Overview
Jun 17, 2010 · This white paper provides an overview of the IEEE Std 802.3ba-2010 40 Gb/s and 100 Gb/s Ethernet standard and the underlying technologies. Page ...
[15]
https://www.ieee802.org/3/ae/public/documents/XAUIjittercomments.pdf
[16]
[PDF] XAUI TX/RX Jitter Specifications - IEEE 802
Jul 26, 2001 · • AC Coupled, point-to-point, 100 Ohms Differential. • 1UI = 320ps +/- 100ppm. • Output voltage limits. – 1600mV differential amplitude. – -0.4V ...
[17]
[PDF] Unconfirmed Minutes IEEE 802.3AP - Backplane Ethernet May 26
May 26, 2004 · • No maintenance request has been submitted to fix XAUI (for 50cm (20 inches only)). • Maintenance would not deal with a new item, such as XAUI ...Missing: reach | Show results with:reach
[18]
4.3. XAUI - Intel
The IEEE 802.3ae-2002 specification requires the XAUI PHY link to support a 10 Gbps data rate at the XGMII interface and four lanes each at 3.125 Gbps at ...
[19]
[PDF] Stratix GX Device Handbook, Volume 2 - XAUI Mode - Intel
The 10 Gigabit Attachment Unit Interface (XAUI) is an optional, self-managed interface that can be inserted between the reconciliation sublayer and the PHY ...
[20]
[PDF] TLK10031 Single-Channel XAUI/10GBASE-KR Transceiver
The TLK10031 is a single-channel multi-rate transceiver intended for use in high-speed bi-directional point-to-point data transmission systems. This device ...
[21]
IEEE P802.3ae 10Gb/s Ethernet Task Force
Jul 12, 2000 · XAUI/XGXS Proposal. Slide 18. IEEE 802.3ae. Task Force. Clock Tolerance Compensation. ▫ The XGXS must restore the temporal fidelity of the ...
[22]
None
### Summary of XAUI Encoding, Data Path, and Related Details
[23]
[PDF] 10-G BASE X &XAUI(Clause 48 &47) - UNH-IOL
Increases the operational distance of the XGMII,increases the physical separation between the MAC and PHY. XAUI spans over a distance of 50 cm.
[24]
[PDF] 10-Gbps XAUI Transceiver (Rev. D - Texas Instruments
The TLK3114SC device supports the IEEE 802.3 defined management data input/output (MDIO) interface to allow ease in configuration and status monitoring of the ...
[25]
RXAUI - AMD
The AMD Reduced 10 Gigabit Attachment Unit Interface (RXAUI) LogiCORE™ IP provides a 2-lane high speed serial interface at 6.25 Gbps, providing up to 10 ...Missing: variant | Show results with:variant
[26]
[PDF] VSC8491-17 Datasheet WAN/LAN/Backplane RXAUI/XAUI to SFP+/ ...
Drive the SSN pin low to enable the interface. The interface is disabled when SSN is high and MISO is placed into a high impedance state. The VSC8491-17 ...
[27]
[PDF] RXAUI v4.3 LogiCORE IP Product Guide (PG083)
Oct 5, 2016 · The mapping of lanes to data bits is shown in Table 3-1. The lane number is also the index of the control bit for that particular lane; for ...
[28]
Broadcom to acquire Dune Networks for $178 million - Reuters
Nov 30, 2009 · Chipmaker Broadcom Corp <BRCM.O> said on Monday it agreed to buy privately held Dune Networks for around $178 million in cash in a move to ...
[29]
[PDF] RXAUI Interface and RXAUI Adapter Specifications - OpenCores
The Marvell RXAUI Adapter is designed to enable the connection of four lanes of 8/10 PCS to two. 6.2 GHz SERDES lanes. It is provided as verilog RTL code and ...
[30]
[PDF] 88X2222 Datasheet - Public - Marvell Technology
Nov 20, 2020 · The host-side interface supports 4 ports of 10GBASE-R,. RXAUI, 1000BASE-X, and 2 ports of XAUI. Any port from the host side can be attached to ...Missing: variant | Show results with:variant
[31]
Dual XAUI serdes transceiver - EE Times
Aug 13, 2002 · This transceiver incorporates eight serdes lanes, each featuring a selectable 8B/10B encoder/decoder. The eight lanes can be configured as two ...
[32]
[PDF] AT8242 - Kontron
DXAUI (2x 20Gbps) links. Supports bandwidth of 320Gbps; pin compatible ... Manages the Broadcom Ethernet switch through a PCIe x1 Gen1 (2.5 Gbps) lane.
[33]
[PDF] VSC8486-04 Datasheet 10 Gbps XAUI or XGMII to XFI LAN/WAN ...
The WAN interface sublayer (WIS) is defined in IEEE Standard 802.3ae Clause 50. ... The PHY XS block interfaces from the four-lane 10 Gbps attachment unit ...
[34]
[PDF] VSC8491 Hardware Design Checklist - Microchip Technology
- XAUI (10G) uses all four TX path lanes and four RX path lanes per channel. (See Figure 6-1.) - RXAUI (10G) uses lanes 0 and 2. Lanes 1 and 3 can be left ...Missing: directional adaptations<|separator|>
[35]
Choose Tx and Rx Pins Wisely on High Speed Interfaces
Nov 6, 2023 · Sometimes, Tx and Rx pins get grouped together on ASIC interfaces or FPGA I/Os. Here's how to handle these groupings.Missing: XAUI adaptations
[36]
802.3dj D2.1 Comment Resolution Optical Track
The pattern of the xAUI-n input signal may be. PRBS31Q, scrambled idle, or a valid xBASE-R signal. Page 5. 5. IEEE P802.3dj Task Force. September 2025.
[37]
[PDF] 802.3dj D2.0 Comment Resolution Logic Track - IEEE 802
IEEE P802.3dj Task Force. July 2025. 802.3dj D2.0 ... ○ This slide package was assembled by the 802.3dj editorial team to provide ... xAUI-n,. xBASE-R Inner FEC, ...
[38]
[PDF] PHY transmitter block error ratio - IEEE 802
Jan 4, 2025 · IEEE 802.3dj Task Force. 1. PHY transmitter block error ratio. Draft ... A + xAUI-n or. 3 x PM. A + 2. xAUI-n. PHY transmitter under test. In n.<|separator|>
[39]
IEEE P802.3dj D1.3 200 Gb/s, 400 Gb/s, 800 Gb/s, and 1.6 Tb/s ...
Jan 23, 2025 · Footnote a should be applied to the xAUI-n C2C in the bottom row as well as the top. ... 2025 802.3dj task force meeting. ACCEPT IN PRINCIPLE.
[40]
RXAUI Interface and XAUI to RXAUI Interface Adapter - OpenCores
RXAUI interface uses two 6.25Gbps SERDES lanes to carry 10GE, instead of using four 3.125Gbps SERDES lanes. This enables a high port count lower power multi ...Missing: modules IP
[41]
BCM84728 | Dual-Channel 10-GbE SFI-to-XAUI™ LAN/WAN PHY
The BCM84728 is a lower-power version of the BCM8728 dual SFI-to-XAUI PHY and also supports 1588 and WAN interface Sublayer (WIS) mode.Missing: SerDes Framer
[42]
[PDF] BCM8727 Product Brief
Mar 16, 2009 · The BCM8727 is a dual-channel 10-GbE SFI-to-XAUI transceiver with EDC, supporting SFP+ copper twin-ax up to 15m and 300m of Multimode Fiber.
[43]
Overcoming 40G/100G SerDes design and implementation challenges
Nov 2, 2011 · By using a multi-lane approach, systems designers achieve much higher aggregate data rates than the fundamental electrical line rate. The XLAUI ...
[44]
[PDF] IEEE 802.3 architecture and 40/100GbE
Nov 13, 2007 · XAUI is standardized instantiation of XGMII Extender (Clause 47) ... Industry standard or IEEE standard? ▫. Could leverage 10GBASE-KR ...Missing: details | Show results with:details
[45]
[PDF] High-Speed Serial I/O Made Simple
This is a designer's guide for high-speed serial I/O, with FPGA applications, by Abhijit Athavale and Carl Christensen.
[46]
XAUI - Diodes Incorporated
XAUI is commonly used as backplane in networking switches to connect line cards to switch cards. Diodes Incorporated offers a wide variety of ReDrivers™, ...
[47]
Xilinx Provides Proven XAUI Solution For 10 Gigabit Ethernet ...
In addition, Xilinx also announced two new IP cores today, the XAUI and Ethernet 1000BASE-X PCS/PMA LogiCOREâ„¢ products. Both cores are available now for use ...Missing: legacy AMD Synopsys
[48]
Xilinx Delivers Complete Virtex-5 FPGA Solution for XAUI Protocol
Mar 17, 2008 · The solution enables engineers to quickly get a design using XAUI up and running on a desktop PC, including all components needed to bring-up a ...
[49]
https://www.researchandmarkets.com/reports/6072496/10gbe-ethernet-controller-market-report-trends
[50]
The Network Structure Undergoing Significant Changes in 25G and ...
24 oct. 2024 · This article primarily examines the shift towards 25G/100G data centers and identifies the evolving network structure.
[51]
XAUI Riser Ethernet Card for QorIQ P4080 Development System
NXP's XAUI (10 Gigabit Attachment Unit Interface)-Riser Ethernet network card is designed primarily to test the XAUI interface for the QorIQ P4080 ...
[52]
[PDF] 100GE and 40GE Skew - IEEE 802
data shows a max skew @ 1300 nm of 1.7ns. (44.5 UI) for ... Thank you ! Page 19. 19. Backup slides. Page 20. 20. XAUI skew (from IEEE 802.3 Table 47-4) – for.
[53]
[PDF] D25.2: “Report on Y1 and updated plan for activities” - BONE - UPC
The low pin count physical interfaces are XLAUI and CAUI for 40GbE and 100GbE, respectively, that enables partitioning in the similar way as XAUI. Each lane ...
[54]
[PDF] Innovating With a Full Spectrum of 40-nm FPGAs and ASICs ... - Intel
Feb 4, 2009 · Networks have migrated to packet-based transmission and all-Ethernet- based equipment, with applications ranging from bridging to full data-path.
[55]
XAUI and 10GBASE-X - of IEEE Standards Working Groups
Mar 13, 2000 · Source impedance can be 100 ohm +/- 50% (10 dB today). • Receiver input voltage tolerance (D2.1). – Limited to 1600mV when source is 100 ohm +/-.
[56]
Synopsys Wins analogZONE'S 'Best Connectivity IP' Award for Its ...
Synopsys provides flexible licensing options for the DesignWare Cores. Each core can be licensed individually, on a fee-per-project basis, or users can opt ...
[57]
3 Embedded Computing Platforms Powering the Future of Edge AI
Apr 7, 2025 · Dual 10G Ethernet ports, USB 3.0, PCIe Gen 3 interfaces; Low-latency, high-bandwidth design ideal for AI inference at the edge. Article ...<|control11|><|separator|>