Fact-checked by Grok 2 weeks ago

Current-mode logic

Current-mode logic (CML), also known as source-coupled logic (SCL), is a differential digital logic family that performs logic operations by steering a constant tail current between paired transistors, rather than relying on voltage level swings, to achieve high-speed signaling with inherent common-mode noise rejection.^[1] This architecture typically features a differential pair biased by a tail current source and load resistors, producing output swings proportional to the current times resistance product, often around 800 mV differentially.^[2] CML operates at data rates exceeding 10 Gbps in advanced processes, making it suitable for point-to-point interfaces.^[2] The origins of CML are rooted in emitter-coupled logic (ECL) from the 1960s, with adaptations for MOS technologies emerging in the late 1970s and 1980s to enable nanosecond delays in NMOS VLSI circuits.^[3] Early implementations, such as those described in 1981, demonstrated speed-power products as low as 1.5 pJ using reference-biased gates for high-density integration.^[3] By the 1990s, CML gained prominence in gigahertz MOS pipelines and mixed-signal designs, evolving into MOS current-mode logic (MCML) for reduced supply voltages.^[1] CML offers several advantages over voltage-mode logics, including lower propagation delays, higher bandwidth, and robustness against supply noise and process variations due to its constant current biasing.^[4] ^[1] However, it consumes higher static power and requires precise current sources, often mitigated by inductive peaking or adaptive biasing in modern designs.^[1] It is widely applied in high-speed serial links like SerDes, clock-and-data recovery circuits, voltage-controlled oscillators (VCOs), and multi-gigabit interfaces such as XAUI.^[2] ^[4]

Introduction

Definition and Overview

Current-mode logic (CML), also known as source-coupled logic (SCL), is a differential digital logic style that encodes binary states (logic 0 or 1) by steering a constant current supplied by a tail current source between two complementary paths in a differential transistor pair.^[5]^[1] This current-steering mechanism allows the logic to operate with small differential voltage swings, typically on the order of hundreds of millivolts, while maintaining a constant total current flow.^[2] The core operational paradigm relies on the differential pair to direct nearly all of the tail current to one branch or the other based on the input differential voltage, thereby representing logic levels without large voltage transitions.^[5] Key components of a basic CML gate include the differential transistor pair (implemented using field-effect transistors (FETs) or bipolar junction transistors (BJTs)), load resistors (or active loads) connected to the outputs, and the tail current source that provides a bias-independent constant current.^[1]^[5] The load elements convert the steered current differences into small voltage variations across the differential outputs, which can then drive subsequent stages.^[1] This architecture ensures balanced operation and inherent common-mode rejection, contributing to its noise resilience.^[5] In contrast to voltage-mode logic families like complementary metal-oxide-semiconductor (CMOS), where binary states are represented by switching full voltage levels (e.g., from ground to supply rail) and power is primarily dynamic, CML emphasizes current directionality with minimal voltage swing, leading to constant static power dissipation but reduced switching noise and supply bouncing.^[2]^[5] CML's design is particularly suitable for high-speed digital gates in integrated circuits and board-level signaling interfaces, such as those in multi-gigabit serial data links, where its low-impedance outputs and tolerance to interconnect variations enable reliable operation at data rates exceeding 10 Gbps.^[2]^[1]

Historical Development

Current-mode logic traces its origins to emitter-coupled logic (ECL), a bipolar transistor-based family developed in the 1950s for high-speed computing applications. ECL was invented in 1956 by Hannon S. Yourke at IBM, initially known as current-steering logic, and first deployed in systems like the IBM 7090 and 7094 computers in the early 1960s.^[6] This logic family achieved speeds up to tens of megahertz by avoiding transistor saturation and using small voltage swings, but its bipolar foundation limited integration density compared to emerging MOS technologies.^[7] The evolution toward MOS-compatible current-mode logic (CML) began in the early 1980s, with initial publications on MOS current-mode circuits, including DC analyses and layout systems for LSI chips, to address the need for high-speed circuits in CMOS VLSI processes.^[8]^[9] The foundational work on MOS current-mode logic (MCML) was presented in Z. Tang's 1988 PhD thesis at Tsinghua University, which explored MCML circuits as a differential, low-swing alternative to static CMOS for reducing power and noise in integrated systems.^[10] A seminal publication advancing MCML for gigahertz applications appeared in 1996, introducing an adaptive pipeline technique using MCML gates that compensated for process variations while achieving 1 GHz operation in 0.5 μm CMOS.^[11] During the 1990s, CML gained traction in deep submicron CMOS processes, where bipolar ECL faced scaling challenges like increased parasitics and integration costs; for instance, B. Razavi's 1995 design of a 2.4 GHz frequency divider in 0.1 μm CMOS highlighted CML's suitability for low-voltage, high-speed phase-locked loops.^[12] By the early 2000s, adaptations like subthreshold MCML emerged to enable ultra-low-power operation, with a 2008 study demonstrating robust MCML gates using novel load devices that maintained functionality at supply voltages below 0.5 V and bias currents under 1 μA, targeting wireless sensor networks.^[13] This period marked CML's shift from niche high-speed roles to broader VLSI integration, driven by CMOS scaling benefits. As of 2025, developments have integrated CML into advanced nodes like 5 nm FinFET for AI accelerators and 100+ Gbps SerDes, exemplified by a 2024 inductorless CML divider operating from 2.9 to 45.9 GHz in 65 nm CMOS for high-speed applications, enabling low-jitter performance in data-center interconnects.^[14]^[15]

Principles of Operation

Basic Circuit Structure

The basic circuit structure of a current-mode logic (CML) gate, exemplified by a buffer or inverter, features a differential pair of transistors, typically NMOS devices M1 and M2, with their sources tied together and connected to a tail current source I_{SS} provided by a bias transistor operating in saturation. The drains of M1 and M2 connect to load resistors R_D, which are coupled to the positive supply voltage V_{DD}. Differential inputs are applied to the gates of M1 and M2, while differential outputs are extracted from the drains, enabling current steering rather than voltage switching for logic operation.^[1] The tail current source ensures a constant I_{SS}, typically ranging from 0.5 to 5 mA depending on the technology and performance requirements, with the tail transistor biased to maintain saturation for stable current delivery independent of input variations. Differential inputs steer I_{SS} between the branches: a positive differential voltage favors current flow through one transistor (e.g., M1), increasing the voltage drop across its load resistor and producing complementary outputs, while the common-mode input level is set to keep the pair in the active region. This biasing configuration minimizes supply dependence and supports high-speed operation by avoiding full rail-to-rail voltage transitions.^[1] The differential output voltage swing \Delta V_{out} is determined by \Delta V_{out} = I_{SS} \times R_D. To derive this, consider a large positive differential input that fully steers I_{SS} through M1, with negligible current through M2; the drain voltage of M1 then drops to V_{DD} - I_{SS} R_D, while the drain of M2 stays near V_{DD}, yielding a peak-to-peak differential swing of I_{SS} R_D. For smaller inputs, the swing scales with the degree of current steering, but the maximum remains supply-independent as long as the output common-mode voltage stays within the dynamic range. CML designs often align the output common-mode level (around V_{DD} - 1.3 V) for compatibility with Positive Emitter-Coupled Logic (PECL), enabling straightforward single-ended interfacing via resistors or AC coupling without complex level shifters. In general, the common-mode voltage is V_{DD} - (I_{SS} R_D / 2).^[1]^[16] Parasitic capacitances at the output nodes, including drain-to-bulk (C_{DB}) and gate-to-source (C_{GS}) components, contribute to the total load and limit bandwidth by increasing the time constant with R_D. Gate-drain capacitance (C_{GD}) exacerbates this through the Miller effect, often countered by adding neutralization capacitors across the differential pair to cancel feedforward coupling. These parasitics necessitate careful sizing of R_D and transistor widths to balance speed and power.^[1]

Logic Implementation and Signal Characteristics

In current-mode logic (CML), basic logic functions such as AND and OR are realized through current summing in the differential pull-down network. Multiple input differential pairs are connected in parallel, where the tail currents from each pair are steered based on their respective inputs, and the summed currents flow through shared load resistors to produce the output voltage differential. This approach allows for multi-input gates without stacking transistors, maintaining the constant tail current and enabling high-speed operation. For example, a two-input AND gate sums the currents from two differential pairs, with the output logic level determined by the minimum input condition due to the steering mechanism. XOR gates in CML are implemented using additional differential pairs to achieve the required cross-coupling. Typically, this involves two pairs: one pair controlled by inputs A and its complement, and another by B and its complement, with outputs taken from the differential nodes to produce the XOR function. The steering of the tail current I_SS in each pair ensures that the output current reflects the exclusive-or condition, converting to voltage via the load resistors R_D. This configuration provides both true and complementary outputs, facilitating further logic chaining. CML employs fully differential signaling, generating both true (Q) and complementary (Q̅) outputs from differential inputs. This balanced architecture ensures that the common-mode voltage remains stable, as any common-mode variations affect both output branches equally and are rejected by subsequent differential stages. The stability of the common-mode voltage is maintained by the constant tail current source and symmetric load resistors, yielding a common-mode voltage of V_{DD} - (I_{SS} R_D / 2). High common-mode rejection arises from the differential nature, providing rejection ratios often exceeding 40 dB, which suppresses noise and interference effectively. Signal characteristics in CML include a low differential voltage swing, typically ranging from 100 mV to 500 mV, which reduces power dissipation and electromagnetic interference while allowing operation at high frequencies. The output voltage differential is given by ΔV_out = I_SS · R_D, where the small swing minimizes capacitive loading effects. This low swing, combined with the differential structure, enables high common-mode rejection, making CML suitable for noise-sensitive environments.^[17] The propagation delay τ_pd in CML gates is approximated by the time constant of the output RC network, τ_pd ≈ R_D · C_L, where R_D is the load resistance and C_L is the total load capacitance at the output node. To derive this, consider a step input that fully steers the tail current I_SS to one branch, causing an exponential change in the output voltage: V_out(t) = V_CM + (ΔV_out / 2) · (1 - e^{-t / (R_D C_L)}), where V_CM is the common-mode voltage and ΔV_out = I_SS · R_D. The delay is defined as the time for the output to reach 50% of its final swing, yielding τ_pd = ln(2) · R_D · C_L ≈ 0.69 · R_D · C_L; however, for small-signal analysis and simplified modeling, the approximation τ_pd ≈ R_D · C_L captures the dominant pole and provides accurate estimates with errors below 9% in 65-nm CMOS processes. This model averages small-signal parameters between logic high and low states for precision across gate types.^[18] Waveforms in CML operation feature a differential input voltage that modulates the gate-source voltages of the input transistors, steering the tail current I_SS between the two branches of the differential pair. When the input differential is positive, I_SS flows primarily through one branch, producing a voltage drop across the corresponding load resistor and generating a negative-going output on that side, while the complementary output rises. The output waveform is then a current-to-voltage conversion via the loads, resulting in small-swing differential pulses with fast rise/fall times determined by the RC time constant. CML gates exhibit unity voltage gain due to their differential transconductance and load configuration, allowing direct chaining without amplification but requiring consideration of fan-out. To drive multiple loads or maintain signal integrity over longer paths, unity-gain buffers—essentially source-follower or simple differential amplifiers—are inserted, preserving the low swing and common-mode level while isolating capacitive loads. This buffering prevents delay degradation from excessive fan-out, typically limited to 4-8 loads in high-speed designs.

Variants and Implementations

MOS Current-Mode Logic

MOS Current-Mode Logic (MCML) implements current-mode logic using standard CMOS transistors, featuring an NMOS differential pair whose sources are tied to a tail current source for steering the bias current based on differential inputs. The drains of this pair connect to PMOS active loads biased to operate in the triode region, functioning as tunable resistors that replace passive loads in earlier designs for enhanced swing control and process compatibility. This configuration ensures constant current flow, with the differential output voltage determined by the current split between the branches, providing low-noise, high-speed operation in CMOS environments.^[5]^[19] Transistor sizing in MCML emphasizes matching to optimize current steering and minimize offsets, with the NMOS differential pair transistors designed to have identical W/L ratios—such as 720 nm/180 nm in a 180 nm process—for symmetric transconductance and balanced operation. The PMOS loads are scaled with larger widths relative to lengths to achieve the desired effective resistance R_D, while the tail NMOS transistor, often with a longer channel like 720 nm/720 nm, sets the total bias current I_{SS} through its gate bias voltage V_{\text{bias}}, ensuring high output impedance and stable current independent of input swings. These ratios allow trade-offs between speed, power, and area, with non-minimum lengths reducing short-channel effects and improving matching.^[17]^[19] The logic threshold V_{\text{th}} in an MCML differential pair represents the input condition for balanced current steering, expressed as

V_{\text{th}} = \frac{V_{\text{GS1}} + V_{\text{GS2}}}{2},

where V_{\text{GS1}} and V_{\text{GS2}} are the gate-source voltages of the NMOS pair at equilibrium, ideally equal for zero differential input. Mismatch effects, including threshold voltage variations \Delta V_{\text{th}} and differences in mobility or oxide thickness, introduce an input-referred offset approximately \Delta V_{\text{th}} / \sqrt{2}, shifting the transfer curve and causing partial current steering even at nominal inputs. This offset amplifies in cascaded gates, degrading noise margins; mitigation involves larger transistor areas to reduce mismatch variance per Pelgrom's model, where standard deviation scales as $1 / \sqrt{WL}.^[20]^[19] MCML benefits from full compatibility with standard CMOS fabrication processes, utilizing only enhancement-mode MOS transistors without the specialized bipolar junctions required for emitter-coupled logic (ECL), enabling seamless integration in digital fabs. This process alignment reduces manufacturing costs and supports mixed-signal designs. Compared to bipolar CML variants, MCML achieves smaller die area due to the compact MOS structure—lacking base-emitter junctions—and efficient layout, with gates occupying up to 9% less space than equivalent static CMOS blocks in near-threshold regimes while maintaining high density.^[21]^[17] Variability in MCML arises primarily from process-induced fluctuations in threshold voltage V_{\text{th}}, which disrupt precise current steering by altering the NMOS pair's conduction balance and leading to uneven I_{SS} distribution. In PVT analysis using 180 nm CMOS corners (e.g., slow-slow, fast-fast), V_{\text{th}} shifts of ±50 mV can increase bias current by up to 30% and reduce output swing by 28%, exacerbating power variations and timing skews in high-speed chains. These effects are unique to MOS implementations, as short-channel variations amplify V_{\text{th}} sensitivity; countermeasures include oversized channels for lower mismatch density and layout symmetries like common-centroid placement to equalize gradients.^[19]^[20]

Subthreshold and Low-Power Variants

Subthreshold current-mode logic (STSCL), also known as subthreshold source-coupled logic, adapts conventional current-mode logic circuits for ultra-low-power operation by biasing transistors in the weak inversion regime, where the gate-source voltage V_{GS} is below the threshold voltage V_{th}. This enables gate currents as low as 10-100 pA, significantly reducing static power dissipation while maintaining differential signaling.^[22]^[23] In subthreshold operation, the drain-source current I_{DS} of a MOSFET follows an exponential relationship derived from the EKV charge-based model:

I_{DS} = I_0 \exp\left(\frac{V_{GS} - V_{th}}{n V_T}\right) \left(1 - \exp\left(-\frac{V_{DS}}{V_T}\right)\right),

where I_0 is the specific current (technology-dependent, typically ~1 μA for minimum channel length), n is the subthreshold slope factor (1.3-2), and V_T = kT/[q](/page/Q) \approx 26 mV at room temperature is the thermal voltage. For V_{DS} \gg V_T (saturation), the equation simplifies to I_{DS} \approx I_0 \exp\left((V_{GS} - V_{th})/(n V_T)\right). In an STSCL differential pair, a tail bias current I_{SS} (picoamperes range) is steered between the two branches based on the differential input voltage \Delta V = V_{GS1} - V_{GS2}. The branch currents are:

I_1 = \frac{I_{SS}}{1 + \exp\left(-\frac{\Delta V}{n V_T}\right)}, \quad I_2 = \frac{I_{SS} \exp\left(-\frac{\Delta V}{n V_T}\right)}{1 + \exp\left(-\frac{\Delta V}{n V_T}\right)}.

This exponential splitting ensures high steering efficiency, where for |\Delta V| > 4 n V_T, over 99% of I_{SS} is directed to one branch, enabling reliable logic switching with minimal input swing (~100-200 mV). The output differential voltage swing V_{sw} = I_{SS} R_L (with load resistance R_L) must exceed $4 n V_T (~200-300 mV) to propagate signals effectively to the next stage.^[24]^[13] Power reduction in STSCL leverages the low I_{SS} for static savings, augmented by techniques like dynamic biasing, where I_{SS} is adjusted via a variable current source to match workload demands, linearly scaling power and frequency. Duty cycling intermittently activates circuits during computation phases, minimizing average power by exploiting the low standby leakage (subthreshold current dominates but remains in picoamperes). Power gating at the gate level, as in PG-STSCL, inserts sleep transistors to cut I_{SS} entirely during idle periods, addressing residual CMOS leakage without performance overhead upon wakeup. These methods yield energy efficiencies orders of magnitude better than standard CMOS in standby, ideal for always-on sensors.^[25]^[26]^[27] Despite these benefits, STSCL trades speed for power: operating frequencies drop from GHz in nominal CML to MHz (e.g., 1-10 MHz at 0.5-0.8 V), limited by the low transconductance g_m = I_{SS}/(n V_T). It also exhibits heightened sensitivity to noise, process mismatch, and temperature variations, as the exponential current dependence amplifies small perturbations (e.g., 1 mV input noise can cause ~10% current error), necessitating careful sizing and calibration.^[28]^[29] STSCL was proposed in the mid-2000s for ultra-low-power digital systems, with seminal work introducing novel PMOS loads for enhanced low-current performance. It has since evolved for Internet-of-Things (IoT) and wearable applications, incorporating power-gated variants and integration in mixed-signal designs, though specific 28 nm implementations remain focused on broader subthreshold optimizations rather than STSCL-exclusive advances.^[13]^[30]^[25]

Performance Characteristics

Advantages in Speed and Noise

Current-mode logic (CML) achieves high-speed operation primarily through its small differential voltage swing, typically around 800 mV, which is determined by the product of the tail current I_{SS} and load resistance R_D (\Delta V = I_{SS} R_D). This reduced swing minimizes the RC time constant associated with charging parasitic capacitances, enabling bandwidths exceeding 10 GHz in applications such as frequency dividers and serial I/O interfaces. For instance, CML-based circuits have demonstrated operation at 10 Gb/s with low propagation delays.^[1]^[31] The propagation delay of a CML stage is given by t_d = 0.69 R_D (C_{par}), where C_{par} represents the total parasitic capacitance at the output node, making the delay largely independent of the supply voltage V_{DD} as long as the bias current remains constant. This characteristic allows CML to maintain consistent high-speed performance across varying supply conditions, unlike voltage-mode logics where delay scales with V_{DD}. The maximum operating frequency is fundamentally limited by the bandwidth of the differential pair, approximately f_{max} \approx 1/(2\pi R_D C_{par}), further emphasizing the role of optimized load and parasitics in achieving multi-GHz speeds.^[1]^[32] In terms of noise resilience, CML's fully differential architecture inherently rejects common-mode noise, including crosstalk and supply-induced variations, providing robust signal integrity in noisy environments. This differential operation yields a high power supply rejection ratio (PSRR), typically greater than 35 dB, which suppresses power/ground bounce effects far better than single-ended alternatives.^[1]^[33] Compared to static CMOS logic, CML circumvents the speed limitations of rail-to-rail switching, where transistors approach triode regions near the supply rails, leading to reduced drive strength and increased delay; instead, CML transistors remain in saturation, enabling significantly higher bandwidth in optimized designs. Relative to bipolar emitter-coupled logic (ECL), MOS-based CML delivers comparable high-speed performance with significantly lower static power dissipation while leveraging CMOS process scalability for easier integration.^[32]^[17]^[2] CML also supports precise on-chip impedance matching via parallel termination with resistors tied to V_{DD}, which maintains constant input/output impedance (e.g., 50 Ω) and minimizes reflections in high-speed interconnects. Eye diagrams of CML transceivers exhibit low deterministic jitter, underscoring the clean signaling and minimal timing uncertainty.^[34]^[33]

Limitations and Power Considerations

One of the primary limitations of current-mode logic (CML) is its static power consumption, which arises from the constant bias current I_{SS} required for operation, resulting in power dissipation given by P = I_{SS} \times V_{DD}.^[35] This always-on current leads to significantly higher static power compared to complementary metal-oxide-semiconductor (CMOS) logic, where power is predominantly dynamic and scales with switching activity. For high-speed applications, typical CML gates consume 1-10 mW, such as several mW per equivalent NOR gate in a divide-by-4 frequency divider operating at multi-GHz frequencies.^[35]^[36] In contrast, CMOS gates exhibit negligible static power under similar conditions, making CML less suitable for battery-constrained or ultra-low-power systems without modifications.^[1] CML circuits also exhibit supply sensitivity, where variations in V_{DD} cause common-mode voltage shifts that can degrade signal integrity and performance.^[37] These shifts arise because the differential output common-mode level tracks V_{DD} changes, potentially leading to improper biasing or increased noise susceptibility in cascaded stages. To mitigate this, precise voltage regulation or on-chip supply decoupling is often necessary, adding design complexity.^[2] Additionally, CML's differential architecture increases silicon area and manufacturing costs compared to single-ended CMOS equivalents. Termination resistors, typically 50 Ω per differential line to V_{CC}, further contribute to area overhead and parasitic effects in integrated implementations.^[38] Mitigation strategies for these limitations include adaptive biasing techniques to dynamically adjust I_{SS} based on operating conditions, reducing static power without sacrificing speed.^[39] Hybrid designs combining CMOS for low-activity logic blocks with CML for high-speed paths balance power and performance, minimizing overall dissipation.^[40] Power-delay product (PDP) analysis, defined as PDP = P \times \tau_{pd}, provides a key metric for optimization, where \tau_{pd} is propagation delay; studies show CML PDP can be competitive with CMOS at GHz speeds when bias currents are tuned for minimum energy per operation.^[39] Power-gating schemes, such as inserting sleep transistors to cut off I_{SS} during idle periods, further address static power in MOS current-mode logic variants.^[36] In dense integrated circuits, the constant current in CML contributes to self-heating effects, exacerbating thermal gradients and reliability issues due to elevated junction temperatures.^[41] This thermal runaway risk is pronounced in high-density layouts, where localized heat from multiple gates accumulates, potentially increasing leakage and variability.^[42] Effective thermal management, such as substrate engineering or heat-spreading interconnects, is essential to maintain performance in such environments.^[43]

Applications

High-Speed Interconnects and Interfaces

Current-mode logic (CML) serves as a fundamental signaling scheme in high-speed serial links, offering a current-steering differential approach akin to low-voltage differential signaling (LVDS) but with enhanced performance for multi-gigabit transmission over printed circuit boards and cables. Unlike voltage-based methods, CML maintains constant current flow while switching the differential pair, enabling low-voltage swings (typically 200-800 mV) that reduce electromagnetic interference and support data rates ranging from 312 Mbps to over 28 Gbps per lane. This makes CML ideal for point-to-point, unidirectional interconnects in environments requiring robust signal integrity, such as backplanes and external interfaces.^[4]^[44]^[45] In various communication standards, CML underpins transmitters and receivers for reliable data transfer. For instance, the transition-minimized differential signaling (TMDS) protocol in DVI and HDMI interfaces employs CML drivers to achieve video data rates up to 1.65 Gbps per channel across twisted-pair cables, with DC-coupled outputs terminated to 3.3 V. Similarly, FPD-Link III, a high-speed interface for automotive and industrial camera systems from Texas Instruments, utilizes CML for its 4 Gbps serial output over a single differential pair, enabling compact, low-EMI links for megapixel video. In PCIe Gen4 (16 GT/s) and Gen5 (32 GT/s) ecosystems, CML forms the electrical interface in retimers and switches, such as Broadcom's PEX series, where it facilitates signal conditioning and protocol compliance across multi-lane configurations to extend reach in server and storage interconnects.^[46]^[47] CML interconnects typically incorporate on-chip or external termination networks consisting of 50 Ω resistors to the supply on each leg of the differential pair (yielding a 100 Ω differential impedance) or a single 100 Ω resistor across the receiver inputs, ensuring matched transmission lines and minimizing reflections in high-frequency paths. This termination scheme is critical for maintaining eye diagram quality at gigabit speeds, as seen in applications like optical transceivers for 100G Ethernet, where QSFP28 modules from vendors like 10Gtek use CML-compatible electrical inputs to drive laser modulators over multimode or single-mode fiber, supporting aggregate throughputs up to 100 Gbps via four 25 Gbps lanes.^[16]^[48] The adoption of CML in high-speed interconnects traces back to the 1990s, when it gained traction as a low-power alternative to emitter-coupled logic (ECL) for PCB signaling in early telecommunication gear, such as gigabit Ethernet prototypes. By the 2000s, advancements in CMOS integration propelled CML into multi-gigabit SerDes, and into the 2020s, it supports multi-lane architectures in standards like 400G Ethernet and PCIe 6.0, with aggregate bandwidths exceeding 100 Gbps through parallel lanes and equalization techniques.^[2]^[49]

Integrated Circuits and Mixed-Signal Systems

Current-mode logic (CML) is extensively employed in on-chip applications within integrated circuits, particularly for high-speed components such as frequency dividers and phase detectors in phase-locked loops (PLLs). In PLLs, CML-based frequency dividers operate at multi-gigahertz frequencies, enabling efficient division of the voltage-controlled oscillator (VCO) output to match the reference clock for phase detection, which is essential for clock generation in RF and data communication systems.^[50] For instance, a CML divide-by-2 stage in a 60 GHz PLL synthesizer achieves operation up to 45 GHz while maintaining low phase noise.^[51] Phase detectors in these PLLs often incorporate CML elements, such as current sources gated by flip-flops, to provide precise charge-pump currents with a linear range of ±2π radians, minimizing jitter in feedback loops.^[52] Additionally, CML serializers and deserializers (SerDes) facilitate on-chip data multiplexing, converting parallel data streams to serial formats at rates exceeding 10 Gb/s, which reduces interconnect complexity in system-on-chip (SoC) designs.^[53] In mixed-signal systems, CML integrates seamlessly with analog-to-digital converters (ADCs) and digital-to-analog converters (DACs), particularly in current-to-voltage conversion stages that enhance linearity and reduce distortion. By processing signals in the current domain, CML avoids voltage swings that introduce nonlinearities, allowing direct digitization of current inputs without intermediate voltage conversion, which conserves power and area compared to traditional voltage-mode approaches.^[54] In current-steering DACs, CML buffers at the output stage maintain constant current sources, suppressing glitch energy and harmonic distortion by up to 10 dB in high-resolution conversions.^[55] This makes CML ideal for precision data conversion in mixed-signal ICs, where it interfaces digital logic with analog sections to achieve effective number of bits (ENOB) greater than 10 in pipelined ADCs operating at sampling rates over 1 GS/s.^[56] Practical examples of CML integration include RF synthesizers and 5G mmWave transceivers, where it supports wideband operation in frequency-agile systems. In RF synthesizers, CML dividers provide octet-phase outputs with locking ranges exceeding 20 GHz, enabling low-phase-noise local oscillator generation for wireless standards.^[57] For 5G mmWave transceivers, CML-based PLLs and dividers handle signals up to 40 GHz in the 28-39 GHz bands, optimizing power efficiency in beamforming arrays.^[58] Hybrid implementations combine CML with CMOS logic for digital control, leveraging CML's speed for analog interfaces while using CMOS for low-power computation, often in SiGe BiCMOS processes that enhance gain and frequency response.^[59] These hybrids operate with low supply headroom of 1-2 V, accommodating stacked transistors without exceeding breakdown voltages in scaled nodes.^[60] CML's compatibility with SiGe and BiCMOS technologies further enables integration of high-speed HBTs with CMOS, achieving high transimpedance gains at mmWave frequencies.^[61] As of 2025, CML has emerged in quantum computing control logic, particularly for cryogenic environments where it maintains performance at temperatures below 4 K. In cryogenic control ICs, CML clock distribution paths deliver precise timing signals for qubit manipulation, supporting data rates up to 40 Gb/s in readout chains without cryogenic degradation.^[62] This application addresses the wiring bottleneck in quantum processors by enabling in situ logic at millikelvin temperatures, with CML gates exhibiting speed improvements of 20-30% over room-temperature CMOS equivalents due to reduced thermal noise.^[63] Such advancements facilitate scalable control electronics for superconducting qubits, integrating CML with cryo-CMOS for hybrid classical-quantum interfaces.^[64]

References

[1]
[PDF] Design and Analysis of Low-Voltage Current-Mode Logic Buffers
A current-mode logic (CML) buffer is based on the differential architecture. Fig. 1. (a) shows a basic differential architecture. The tail current, ISS, ...
[2]
[PDF] LVDS, CML, ECL-differential interfaces with odd voltages
CML - Current Mode Logic - The origins of CML are more difficult to track. CML tends to be mainly a vendor implementation with less official standardization.
[3]
Nanosecond NMOS VLSI Current Mode Logic
**Summary of Content from https://ieeexplore.ieee.org/document/1051750**
[4]
[PDF] Current-Mode vs Voltage-Mode Summary
Current-Mode Logic (CML) Driver. 7. • Used in most high performance serial links. • Low voltage operation relative to push-pull driver. • High output common ...Missing: definition | Show results with:definition
[5]
[PDF] Design of MOS Current-Mode Logic Standard Cells
MOS Current-Mode Logic (MCML) is an alternative logic designing style that provides true differential operation, low noise level generation and noise ...
[6]
https://semiconductormuseum.com/Transistors/IBM/OralHistories/Yourke/Yourke_Index.htm
[7]
http://semiconductormuseum.com/Transistors/IBM/OralHistories/Yourke/Yourke_Page2.htm
[8]
https://www.semanticscholar.org/paper/DC-analysis-of-current-mode-logic-Treadway/486d172e1f6f2589a7ecabb366f2b7ae5879d94a
[9]
https://dl.acm.org/doi/10.1109/TC.1981.1675842
[10]
https://ieeexplore.ieee.org/document/122653
[11]
[PDF] Interfacing Between LVPECL, VML, CML and LVDS Levels
The main logic levels discussed in this application report are low-voltage positive/pseudo emitter-coupled logic (LVPECL), current-mode logic (CML), voltage- ...
[12]
[PDF] Architecting a MOS Current Mode Logic (MCML) Processor for Fast ...
MOS current-mode logic (MCML), a differential logic family, maintains a low voltage swing and a constant current, making it inherently fast and low- noise.
[13]
https://ieeexplore.ieee.org/document/4430304
[14]
"Analysis of MOS Current Mode Logic (MCML) and Implementation ...
MOS current mode logic (MCML) offers low noise digital circuits that reduce noise that can cripple analog components in mixed-signal integrated circuits, ...Missing: introduction history
[15]
https://ieeexplore.ieee.org/document/9599863
[16]
MOS Current Mode Logic Near Threshold Circuits - MDPI
MOS current mode logic operates at frequencies significantly higher than standard CMOS. These frequencies are achieved due to the low delay of MCML. This ...
[17]
Ultra Low Power Subthreshold MOS Current Mode Logic Circuits ...
Subthreshold operation enables CMOS circuits to operate using very low supply voltages and to dissipate extremely low power with moderate performance. The ...
[18]
[PDF] Subthreshold SCL for Ultra-Low-Power SRAM DIPLOMA THESIS ...
On the other hand , the lower limit for SCL-based circuit power consumption is the stand-by current ISS that can be as low as a few pico-Amperes[3]-[8]-[30].<|control11|><|separator|>
[19]
[PDF] Ultra Low-Power Subthreshold MOS Current Mode Logic Circuits ...
Abstract— This article presents a novel and robust approach for implementing ultra-low power MOS current mode logic. (MCML) circuits.
[20]
Power-Gating Sub-Threshold Source-Coupled Logic (PG-STSCL ...
This paper presents Power-Gating Sub-Threshold Source-Coupled Logic (PG-STSCL), which employs the fine-grain power gating at the gate level. It introduces ...
[21]
[PDF] A SUB THRESHOLD SOURCE COUPLED LOGIC BASED DESIGN ...
The bias current of the SCL gates is varied to scale down linearly the power consumption and the operating frequency. The multiplexer design employs CMOS ...
[22]
[PDF] Leakage Current Reduction Using Subthreshold Source-Coupled ...
Abstract—The performance of subthreshold source-coupled logic (STSCL) circuits for ultra-low power applications is ex- plored. It is shown that the power ...
[23]
Power-Gating Sub-Threshold Source-Coupled Logic (PG-STSCL ...
Aug 6, 2025 · It is a technique used in integrated circuit design to decrease power depletion by closing off the current blocks of the circuit that can be ...Missing: biasing | Show results with:biasing
[24]
https://infoscience.epfl.ch/server/api/core/bitstreams/23c0751b-013b-40d3-b201-041da91b7ca5/content
[25]
[PDF] Ultra low power subthreshold MOS current mode logic circuits ...
... subthreshold SCL (STSCL) can be used effectively for reducing the power consumption. ... Nano-power subthreshold current-mode logic in sub-100 nm technologies.
[26]
A Very-Low-Voltage Frequency Divider in Folded MOS Current ...
Feb 25, 2021 · Abstract: In this article, a static frequency divider based on folded MOS current mode logic (FMCML) is presented. ... 10 GHz with 53-μW power ...
[27]
[PDF] Design of Ultra High-Speed CMOS CML buffers and Latches
A current-mode logic (CML) latch consists of an input tracking stage, MN1 and MN2, utilized to sense and track the data variation and a cross-coupled ...
[28]
[PDF] 3.3V/5V 3.2Gbps CML LOW-POWER LIMITING POST AMPLIFIER W ...
PSRR. Power Supply Rejection Ratio. 35. dB tr,tf. Output Rise/Fall Time. Note 7. 60. 120 ps. (20% to 80%). tJITTER. Deterministic. Note 8. 15. psPP. Random. 5.
[29]
[PDF] Lecture 8: Termination & TX Driver Circuits
• Large variance in FET threshold voltage requires adjustable ... • Used in Low-Voltage Differential Signals (LVDS) standard. • Driver current ...
[30]
A high-speed, low-power divide-by-4 frequency divider implemented ...
Aug 31, 1989 · ... current-mode logic (CML) gate with a fan-out of 2, and a total power consumption of 67 mW (about 4.5 mW per equivalent NOR gate). These ...<|control11|><|separator|>
[31]
Power-gated MOS current mode logic (PG-MCML)
MOS Current Mode Logic (MCML) is one of the most promising logic style to counteract power analysis attacks. Unfortunately, the static power consumption of ...
[32]
[PDF] CCO and VCO implemented by CMOS current mode logic stages
MOS current-mode logic (MCML) style was first introduced with the adaptive pipeline technique (APL) that allowed to compensate for deviations in the ...
[33]
Design of MCML Based Logic for Low Power Digital Communication ...
The major disadvantage of conventional CMOS logic is slower operation and higher energy consumption. Current steering logic is utilized by MOS Current Mode ...
[34]
Self-timed MOS current mode logic for digital applications
ST-MCML is compared to conventional MCML, static CMOS and domino logic in terms of power, delay, Power-Delay-Product (PDP) and Energy-Delay-Product (EDP). ST- ...
[35]
A High Speed Dynamic MCML Style - Wiley Online Library
Jan 27, 2016 · The MOS current mode logic (MCML) is a promising alternative to CMOS logic, in both reducing power consumption at high frequencies and providing ...
[36]
https://dl.acm.org/doi/10.1145/2024724.2024947
[37]
(PDF) Impact of self-heating and thermal coupling on analog circuits ...
Aug 9, 2025 · PDF | This paper examines the influence of the static and dynamic electrothermal behavior of silicon-on-insulator (SOI) CMOS transistors on ...
[38]
Accurate Thermal Analysis, Including Thermal Coupling Of On-Chip ...
Oct 15, 2015 · This blog describes an innovative method for efficiently and accurately calculating the temperature increase on millions of wires due to self-heat.
[39]
[PDF] High-Speed Digital Logic (HSDL) Interfacing HSDL Current-Mode ...
Oct 16, 2014 · Current-Mode Logic (CML) I/O logic interfacing standard. CML is the best choice for multi-gigabit high-speed digital signals. Here are some ...Missing: seminal paper interconnects 1990s
[40]
[PDF] Design Techniques for High-Speed Wireline Transmitters
Sep 29, 2021 · For multiplexing to higher data rates, we can resort to current-mode logic (CML). For example, suppose 128 inputs at 312 Mb/s must be ...
[41]
[PDF] How to Design a FPD-Link III System Using DS90UB953
For synchronous mode where the reference oscillator is provided by the deserializer, the serial data rate is 4 Gbps presented as a differential CML output on ...
[42]
[PDF] PEX 8604 - Support Documents and Downloads
Sep 3, 2010 · The transmit path typically contains a serializer, Phase Lock Loop (PLL), and Current Mode Logic (CML) driver. The receive path consists of a ...
[43]
[PDF] TSMC 16/12: CML - Aragio Solutions
The CML library provides a differential current mode logic clock driver for REFCLK signaling in PCIe applications, with low jitter and a voltage reference cell.Missing: gen4 gen5 retimers
[44]
[PDF] PolarFire Family PCI Express User Guide - Microchip Technology
• PCI Express 2.0 electrical compliance. • 2.5 and 5.0 Gbps common-mode logic (CML) electrical interface. • Signal integrity programmability including ...
[45]
[PDF] Integrated High Speed Current-Mode Frequency Divider with ...
Abstract—In this paper, a high performance current mode logic (CML) frequency divider is introduced in an integrated. CMOS phase-locked loop (PLL).
[46]
A PLL Frequency Synthesizer In 65 nm CMOS for 60 GHz Sliding-IF ...
The PLL is composed of a voltage-controlled oscillator, a current-mode logic divide-by-2, a programmable frequency divider, a phase /frequency detector, a ...
[47]
Phase-Locked Loop (PLL) Fundamentals - Analog Devices
It uses two D-type flip flops with a delay element. One Q output enables a positive current source, and the other Q output enables a negative current source.
[48]
https://www.aragio.com/assets/PDFfile/resources/TSMC/16nm/rgo_tsmc16_18v18_cml_product_brief_rev_1a.pdf
[49]
[PDF] A Current-Mode Multi-Channel Integrating Analog-to-Digital Converter
The ability to digitize current signals without converting currents to voltages saves power, area, and the design time required to implement I-to-V converters.
[50]
Current Steering Digital-to-Analog Converters
Jan 21, 2021 · The R-2R architecture can be used as a voltage-or current-mode DAC. Most R-2R current-mode architectures are based on the circuit shown in ...
[51]
[PDF] Current mode ADC design in a 0.5-µm CMOS process
In current mode circuits, signals are represented by currents, which are insensitive to the voltage variation. Furthermore, no linear ca- pacitance is needed; ...
[52]
(PDF) A current-mode-logic-based frequency divider with ultra ...
Aug 9, 2025 · This paper presents a comprehensive analysis of a current-mode-logic frequency divider (CML FD) and the theoretical locking range of CML FD.
[53]
Behavioral Analysis and Optimization of CMOS CML Dividers for ...
Sep 25, 2025 · Current-mode logic (CML) dividers are widely used in radio-frequency and millimeter-wave transceivers and frequency synthesizers for its ...
[54]
[PDF] A 2.5-V 45-Gb/s Decision Circuit Using SiGe BiCMOS Logic
These topologies limit the available voltage headroom and result in supply voltages of 3.3 V for emitter-coupled logic. (ECL) [2] and 5 V or higher in. [1].
[55]
SiGe and CMOS Technology for State-of-the-Art Millimeter-Wave ...
This article details the major Si processes, namely Complementary Metal Oxide Semiconductor (CMOS) and SiGe. Bipolar CMOS (BiCMOS), and their foray into the ...
[56]
[PDF] SiGe BiCMOS RF ICs and Components for High Speed Wireless ...
Apr 7, 2005 · These circuits can be implemented with current mode logic (CML) topologies (or variants, such as emitter-coupled logic for bipolars, or ...
[57]
[PDF] Cryogenic Optical Link: Device, Circuit, and System
May 1, 2025 · On the electronic side, the clock path consists of a current mode logic (CML) clock ... computing but also for the control interface in quantum ...
[58]
Cryogenic in situ fabrication of reversible direct write logic circuits ...
Sep 29, 2025 · In situ fabrication of cryogenic, high-performance logic circuits and devices presents a promising solution to address this “wiring bottleneck”.
[59]
A Cryo-CMOS DAC-Based 40-Gb/s PAM4 Wireline Transmitter for ...
Feb 21, 2024 · This article presents the first four-level pulse amplitude modulation (PAM4) wireline transmitter (TX) operating at cryogenic temperatures (CTs).