Fact-checked by Grok 2 weeks ago

Digital AMPS

Digital AMPS (D-AMPS), formally known as Interim Standard-136 (IS-136), is a second-generation (2G) digital cellular telecommunications standard that evolved from the analog Advanced Mobile Phone System (AMPS) to enhance capacity and introduce digital features in North American mobile networks.^[1] It utilizes Time Division Multiple Access (TDMA) with π/4 differentially encoded quadrature phase-shift keying (DQPSK) modulation to support up to three full-rate voice channels per 30 kHz carrier in the 800 MHz band, enabling backward compatibility with AMPS for seamless dual-mode operation.^[2] Adopted by the Telecommunications Industry Association (TIA) in 1994, with revisions in 1996, D-AMPS was widely deployed in the United States, Canada, and parts of Latin America until the early 2000s, when it was largely supplanted by GSM and CDMA technologies.^[3] The standard originated as IS-54 in the late 1980s to address the capacity limitations of AMPS (EIA-553), which used frequency division multiple access (FDMA) and analog frequency modulation in 30 kHz channels across the 824–849 MHz uplink and 869–894 MHz downlink bands.^[4] IS-54 introduced digital voice encoding via Vector Sum Excited Linear Prediction (VSELP) at 7.95 kbit/s, compressed to 16.2 kbit/s over the air with error correction, and structured traffic into 40 ms frames divided into six 6.67 ms slots, though initially supporting only three for full-rate speech.^[4] IS-136 advanced this by replacing analog control channels with a fully digital control channel (DCCH), adding features like mobile-assisted handoff, short message service (SMS), and over-the-air activation, while extending to the 1.85–1.91 GHz uplink and 1.93–1.99 GHz downlink PCS bands with 80 MHz duplex separation.^[3] Transmission occurs at 48.6 kbit/s with a symbol rate of 24.3 ksym/s and a roll-off factor of 0.35, supporting circuit-switched data up to 9.6 kbit/s (or 38.4 kbit/s with compression) and enhanced full-rate codecs like ACELP at 13 kbit/s.^[2]^[3] Key innovations in D-AMPS included hierarchical cell structures for microcells, authentication via unique identifiers (IMSI, TMSI, ESN), and privacy enhancements like the Digital Verification Color Code (DVCC), which improved security over AMPS's analog vulnerabilities.^[4] It supported half-rate channels for up to six users per carrier using 4 kbit/s coding, boosting spectral efficiency, and enabled international roaming through IS-41 signaling protocols compatible with other TDMA and CDMA systems.^[2] Commercial deployment began in 1990 with IS-54 trials, accelerating in 1996 via carriers like AT&T Wireless, and by 1998, it served over 36 countries with annual subscriber growth exceeding 60%, leveraging existing AMPS infrastructure for cost-effective 2G rollout.^[3] Despite its success in tripling capacity over 1G systems, D-AMPS faced challenges from competing standards and was phased out by the mid-2000s in favor of 3G technologies.^[1]

Overview

Definition and Standards

Digital AMPS (D-AMPS), also known as North American TDMA, represents the digital evolution of the original analog Advanced Mobile Phone System (AMPS), employing time-division multiple access (TDMA) to enable multiple voice calls and basic data services within shared frequency channels.^[1] As a second-generation (2G) cellular technology, D-AMPS was designed to enhance capacity and efficiency over its analog predecessor while maintaining compatibility for a smooth transition in existing networks.^[5] The foundational standard for D-AMPS is Interim Standard-54 (IS-54), introduced in 1990 by the Telecommunications Industry Association (TIA), which established dual-mode operation allowing seamless switching between digital TDMA and analog AMPS modes to ensure backward compatibility with legacy devices.^[5] IS-54 focused on digitizing voice transmission using TDMA within the existing AMPS framework, tripling channel capacity by supporting three users per 30 kHz channel without requiring new spectrum allocation.^[6] IS-136, approved in 1996 as an enhancement to IS-54, expanded D-AMPS capabilities by introducing digital control channels, short message service (SMS), and improved signaling for better network management and user features, all standardized under TIA oversight.^[7] This standard fully transitioned away from analog control channels, enabling standalone digital handsets while preserving interoperability with earlier IS-54 equipment.^[8] Key characteristics of D-AMPS include its classification as a 2G TDMA system operating primarily in the 800 MHz cellular band, with later adaptation to the 1900 MHz Personal Communications Service (PCS) band, and its efficient multiplexing of up to three simultaneous users per 30 kHz channel to address growing demand in North American markets.^[8]^[9]

Relation to Analog AMPS

Digital AMPS (D-AMPS), standardized under IS-54, was engineered to reuse the same 30 kHz RF channels and 800 MHz spectrum allocated to the original analog Advanced Mobile Phone System (AMPS), facilitating the deployment of dual-mode handsets that could operate seamlessly in both analog and digital modes within overlaid networks.^[9]^[10] This compatibility was achieved through specific mechanisms, such as retaining AMPS signaling on the forward and reverse control channels (FOCC and RECC) for initial access and call setup, where the network identifies a handset's digital capability during login before assigning a digital traffic channel for voice transmission.^[10]^[11] Additionally, D-AMPS supported inter-system handovers between analog AMPS and digital channels in mixed networks, using a slow associated control channel (SACCH) within each time slot to exchange handover information and maintain connectivity.^[10] The close relation to analog AMPS enabled a gradual upgrade path from first-generation (1G) to second-generation (2G) cellular service without requiring spectrum reallocation, while tripling the capacity per channel—from one analog user to three digital users—through time-division multiple access (TDMA) on existing infrastructure.^[9]^[12] Key differences include D-AMPS's use of digital voice encoding, which provided superior audio quality and inherent resistance to eavesdropping compared to AMPS's unencrypted analog transmission, with IS-54 introducing voice privacy through encryption keys and mask generation for securing voice and signaling messages.^[13]

History

Development

The development of Digital AMPS (D-AMPS), standardized as IS-54, was driven by the rapid growth in mobile telephony demand during the 1980s in the United States, where the analog Advanced Mobile Phone System (AMPS) was limited to one user per 30 kHz channel, leading to capacity shortages in urban areas amid fixed spectrum allocations by the Federal Communications Commission (FCC).^[14] This spectrum constraint, with only 666 duplex channels available nationwide under FCC rules established in the early 1980s, necessitated a digital upgrade to support more subscribers without additional bandwidth.^[15] The Cellular Telecommunications Industry Association (CTIA) highlighted the need for at least a tenfold capacity increase over analog systems in its 1988 Users’ Performance Requirements document, prompting industry-wide efforts to transition to digital technology.^[15] Standardization efforts were led by the Telecommunications Industry Association (TIA), with significant contributions from Bell Labs (part of AT&T) and other major carriers, beginning in 1987 under the TIA's TR45 subcommittee as part of broader Joint Technical Committee initiatives.^[16] Bell Labs, having pioneered the original AMPS system, provided key technical expertise in adapting digital methods to the existing infrastructure.^[17] The process involved collaboration among equipment manufacturers, network operators, and regulatory bodies to ensure interoperability while addressing the FCC's emphasis on efficient spectrum use.^[15] By January 1989, the TIA selected Time Division Multiple Access (TDMA) as the primary access method for the digital upgrade, favoring it over Frequency Division Multiple Access (FDMA) variants or emerging Code Division Multiple Access (CDMA) proposals due to its balance of efficiency and implementation feasibility within the constrained timeline.^[17] The IS-54 standard was finalized and published in March 1990, incorporating dual-mode capability to allow seamless operation with analog AMPS handsets, thereby tripling capacity in the same spectrum by supporting three users per channel.^[14] Notably, IS-54 introduced authentication and voice encryption features, marking the first implementation of such security measures in a commercial mobile system to combat fraud and eavesdropping.^[14] Early challenges centered on maintaining backward compatibility with the widespread analog AMPS infrastructure to avoid stranding existing investments, while achieving substantial capacity gains without disrupting service.^[14] Developers conducted validation trials, including those led by Bell Labs, to test TDMA performance in real-world conditions, navigating debates over modulation schemes and handover procedures.^[15] Regulatory delays from the FCC, which encouraged but did not mandate the transition, further complicated the process, yet the focus remained on a pragmatic, evolutionary approach to digitalization.^[17]

Initial Deployment and Adoption

The initial commercial deployments of Digital AMPS (D-AMPS), based on the IS-54 standard approved in 1990, began in 1992 with installations by AT&T in select U.S. cities.^[5]^[15] These early networks represented the first widespread implementation of TDMA technology in North America, allowing coexistence with existing analog AMPS infrastructure. AT&T expanded D-AMPS coverage nationwide by the mid-1990s, achieving broad population reach as digital services gained traction.^[18] AT&T Mobility served as the primary operator and major adopter of D-AMPS, leveraging the IS-54 standard for its core network.^[5] Other U.S. carriers, including U.S. Cellular, followed suit, while PCS providers began adopting D-AMPS in the 1900 MHz band from 1995 onward to support emerging personal communications services.^[19] By the mid-1990s, D-AMPS networks provided coverage to a significant portion of the U.S. population, exceeding 80% in populated areas. Internationally, adoption occurred in Canada through Rogers Wireless starting in 1993 and in select Latin American markets, though global expansion remained limited due to the rapid rise of GSM as the dominant 2G standard.^[5]^[18] The rollout of D-AMPS enabled the introduction of the first digital handsets, which delivered superior call quality and extended battery life relative to analog AMPS devices, driving user preference toward digital services.^[10] This transition contributed to robust subscriber growth, with U.S. cellular subscribers—largely on D-AMPS and compatible networks—rising from approximately 11 million in 1992 to 55 million by 1997.^[20]

Technical Specifications

Frequency Bands and Channel Structure

Digital AMPS (D-AMPS), standardized under IS-54 and later IS-136, utilizes the same frequency allocations as its analog predecessor AMPS to ensure backward compatibility, primarily operating in the 800 MHz cellular band with uplink frequencies ranging from 824 to 849 MHz and downlink frequencies from 869 to 894 MHz.^[5] This 25 MHz bandwidth per direction supports a total of 832 radio channels across the band, divided equally between two carriers: the A-side (channels 1–416) and B-side (channels 417–832), reflecting the U.S. licensing structure where A-side operators hold rights to the lower frequency block and B-side to the higher.^[21] Each carrier allocates 21 channels for control functions, such as signaling and channel assignment, leaving 395 channels for voice traffic.^[21] In 1995, D-AMPS was extended to the 1900 MHz Personal Communications Services (PCS) band to accommodate growing demand, employing uplink frequencies from 1850 to 1910 MHz and downlink from 1930 to 1990 MHz, with an 80 MHz duplex separation.^[2] This 60 MHz total bandwidth, also divided into 30 kHz channels, provides up to approximately 2000 channels overall, allocated through FCC auctions in blocks (A through F) varying from 5 to 30 MHz per licensee, enabling flexible spectrum usage similar to the cellular band but without the fixed A/B-side division.^[2] The PCS extension significantly boosted network capacity in urban areas, supporting the same channel structure while operating independently of the 800 MHz infrastructure. The channel bandwidth remains 30 kHz throughout both bands, preserving compatibility with analog AMPS equipment and allowing dual-mode operation in shared spectrum.^[1] Unlike GSM, D-AMPS does not employ frequency hopping, relying instead on fixed channel assignments to simplify implementation in existing AMPS networks.^[5] For frequency planning, operators typically adopt a 7-cell reuse pattern to balance coverage and interference, though advanced deployments utilize tighter 4-cell patterns with sectoring to enhance capacity.^[22] Capacity implications stem from the time-division multiple access (TDMA) overlay on these frequency-division multiple access (FDMA) channels, where each 30 kHz carrier is subdivided into 6 time slots, accommodating 3 full-rate voice users (or up to 6 half-rate users) per channel—tripling the efficiency over analog AMPS's single user per carrier.^[1] This structure, combined with the available channels, enables D-AMPS networks to support substantially higher user densities, particularly when integrating control channels for digital signaling across the allocated spectrum.^[1]

TDMA Frame and Modulation

Digital AMPS (D-AMPS), standardized under IS-54, utilizes time-division multiple access (TDMA) to enable multiple users to share the same 30 kHz radio frequency channel by dividing time into discrete slots. The fundamental TDMA frame structure consists of a 40 ms superframe composed of six time slots, each with a duration of 6.67 ms.^[23] This design triples the capacity of the original analog AMPS system by accommodating up to three full-rate voice users per channel, with each user assigned two consecutive slots per frame.^[23] Each time slot contains 324 bits of data, structured as follows: 260 bits for user information (such as digitized voice or data), 12 bits for the slow associated control channel (SACCH) used for power control and handoff measurements, 28 bits for synchronization (SYNC), 12 bits for the digital verification color code (DVCC) to detect co-channel interference, and the remaining bits allocated for guard time, ramp-up, and reserved purposes.^[23] The frame structure differs slightly between the forward link (base station to mobile) and reverse link (mobile to base station) in terms of bit partitioning for user data—130 bits per sub-burst in the forward direction versus 122 bits in the reverse—to accommodate varying overhead needs.^[23] Synchronization and color code bits ensure reliable slot alignment and interference rejection across the 30 kHz channels inherited from analog AMPS.^[23] The modulation scheme employed in D-AMPS is π/4-differential quadrature phase-shift keying (π/4-DQPSK), a differentially encoded variant of quadrature phase-shift keying that rotates the constellation by π/4 radians (45 degrees) between symbols to avoid transitions through the origin, thereby simplifying carrier recovery and enhancing resilience to phase errors in multipath environments.^[24] This modulation encodes two bits per symbol at a rate of 24.3 ksymbols per second, yielding a gross bit rate of 48.6 kb/s per carrier before error correction and other overheads.^[23] Pulse shaping with a raised cosine filter (roll-off factor of 0.35) is applied to limit bandwidth to the 30 kHz channel while minimizing intersymbol interference.^[23] The constant envelope property of π/4-DQPSK allows efficient power amplification with minimal distortion, making it suitable for battery-powered mobile devices.^[24] Slot allocation in D-AMPS supports both traffic and control functions, with the forward and reverse links using synchronized but offset frames to manage timing advances for mobiles at varying distances. In the IS-54 standard, control information is primarily carried over analog channels or embedded in traffic slots via the SACCH, but the IS-136 enhancement introduces a dedicated digital control channel (DCCH) that reuses one time slot per 40 ms frame for broadcasting system information, paging, and access grants.^[9] This DCCH operates continuously on designated carriers, allowing mobiles to monitor every sixth slot in a superframe cycle for efficient power saving.^[7] The IS-136 revision maintains the core 40 ms TDMA frame and six-slot structure of IS-54 without major alterations, preserving backward compatibility while adding the DCCH to enable standalone digital handsets.^[1] A key enhancement is the digital forward control channel (DFCC) within the DCCH framework, which supports faster paging cycles by interleaving short message alerts and system parameters into the broadcast slots, reducing mobile wake-up times compared to the analog control channels of earlier implementations.^[1] These updates facilitate improved call setup efficiency and the introduction of services like short message service (SMS) without disrupting the underlying temporal multiplexing or modulation scheme.^[1]

Voice Coding and Data Services

In the IS-54 standard for Digital AMPS, voice coding utilized Vector Sum Excited Linear Prediction (VSELP), a code-excited linear prediction variant designed for low-bit-rate speech compression. This full-rate coder operated at 7.95 kb/s, encoding 20 ms frames of input speech (sampled at 8 kHz) into 159 bits, while the optional half-rate mode achieved 3.975 kb/s by further optimizing the excitation codebook. VSELP emphasized perceptual quality by prioritizing bits for formant and pitch parameters, enabling three users per 30 kHz channel compared to analog AMPS. Error correction in IS-54 enhanced robustness against fading and interference through a combination of techniques. Class 1 bits (77 perceptually important bits) underwent rate-1/2 convolutional coding with a constraint length of 6, generating 154 parity bits, while a 7-bit cyclic redundancy check (CRC) protected 12 critical bits using the polynomial g_{CRC}(X) = 1 + X + X^2 + X^4 + X^5 + X^7. Data was interleaved across two consecutive 20 ms frames (40 ms total) to provide time diversity, spreading burst errors over multiple transmission slots. The gross bit rate after channel coding reached 13 kb/s per traffic channel, fitting within the TDMA slot structure. The IS-136 revision introduced significant improvements to voice coding for better subjective quality and efficiency. It adopted Algebraic Code Excited Linear Prediction (ACELP) via the IS-641 Enhanced Full Rate (EFR) codec, which maintained a net speech rate of 7.4 kb/s but delivered toll-quality performance closer to wireline standards, thanks to algebraic codebook structures for fixed-pulse excitation patterns. With 5.6 kb/s channel coding overhead, the total gross rate was 13 kb/s, processed in 20 ms frames similar to IS-54. IS-136 also supported a half-rate ACELP option at approximately 4 kb/s net for capacity gains.^[25] Data services in core Digital AMPS (IS-54) were limited, lacking dedicated packet support, but IS-136 expanded capabilities with circuit-switched data (CSD) at up to 9.6 kb/s using a single traffic channel and rate-5/6 convolutional coding with π/4-DQPSK modulation; later implementations extended this to 14.4 kb/s via reduced error protection. Short Message Service (SMS) enabled point-to-point text messaging up to 140 bytes (7-bit encoded), transmitted over the Digital Control Channel (DCCH) in the forward and reverse links for efficient paging and mobile-originated delivery without dedicating full traffic channels. IS-136 further facilitated over-the-air programming (OTA) for handset configuration, leveraging the DCCH for secure parameter updates like authentication keys.^[26]^[27]

Operation

Call Processing

In Digital AMPS (D-AMPS) networks, call origination begins when the mobile station (MS) scans available frequencies to identify the strongest Digital Control Channel (DCCH), which broadcasts system information and paging messages. The MS then transmits an access burst—a short, unique preamble sequence—on a randomly selected slot of the reverse DCCH to request service and avoid collisions with other mobiles. This burst includes the MS's unique identifiers, such as the Mobile Identification Number (MIN) and Electronic Serial Number (ESN), to initiate the process.^[28]^[29] Upon receiving the access burst, the base station (BS) authenticates the MS using the Cellular Authentication and Voice Encryption (CAVE) algorithm, a one-way challenge-response mechanism that generates an authentication triplet from inputs including a random variable (RAND), the shared secret data key (A-key or SSD), MIN, ESN, and electronic serial number. The BS sends a challenge to the MS via the forward DCCH or Slow Associated Control Channel (SACCH), and the MS computes the signed response (AUTHR) using CAVE for verification. If authentication succeeds, the BS assigns a digital traffic channel (DTC), preferring it over analog for efficiency, and notifies the MS via the Fast Associated Control Channel (FACCH) or SACCH; the assigned channel carries voice encoded with Vector Sum Excited Linear Prediction (VSELP) at 7.95 kbit/s. For incoming calls, the network pages the MS on the forward DCCH using its MIN for routing, prompting a similar response and setup sequence.^[30]^[28] During the active call, maintenance procedures ensure signal quality and efficiency. Power control operates in a closed-loop mode, where the BS measures received signal strength and issues commands to the MS via the SACCH to adjust transmit power, typically in discrete steps to balance coverage, interference, and battery life. These commands are sent periodically via the SACCH, aligned with the 40 ms frame structure. Discontinuous transmission (DTX) complements this by detecting speech pauses via voice activity detection (VAD) and silencing the transmitter during silence periods, reducing average power consumption by up to 50% while inserting comfort noise to avoid abrupt muting. These mechanisms apply primarily to digital channels but can interwork with analog AMPS for dual-mode operation.^[28] Call release involves signaling on the FACCH for rapid teardown, supporting both ordered (coordinated) and unordered (emergency) procedures to handle normal termination or failures like radio link loss. In an ordered release, the MS or BS sends a release message, acknowledged by the other party, followed by channel deactivation and return to idle mode on the DCCH. For interworking with analog AMPS, dual-mode MSs may switch to an analog voice channel if digital capacity is unavailable, using AMPS signaling for setup and release while preserving backward compatibility in mixed networks. Unordered release occurs if no acknowledgment is received within a timeout, triggering automatic teardown.^[28]^[31]

Mobility and Handover

In Digital AMPS (D-AMPS), also known as IS-136, mobility management relies on location tracking to enable efficient call routing and resource allocation as mobile stations move across the network. Location areas are defined as groups of cells, allowing the network to page mobiles within a defined region without tracking their exact cell position, which reduces signaling overhead. Mobiles perform autonomous registration every 6 hours to periodically update their location with the Mobile Switching Center (MSC), or immediately upon crossing a location area boundary, powering on, or entering a new system; this process uses the Random Access Channel (RACH) or Digital Control Channel (DCCH) to send registration messages to the Home Location Register (HLR) and Visitor Location Register (VLR) via the IS-41 protocol. Authentication may occur during registration to verify the mobile's identity, ensuring secure location updates.^[32] Handover in D-AMPS is exclusively hard handover, where the connection to the serving base station is broken before establishing a link to the target base station, resulting in a brief interruption of no more than 40 ms per frame. The system employs mobile-assisted handover (MAHO), in which the mobile station continuously monitors the signal quality of neighboring cells and reports measurements to the serving base station to facilitate timely decisions. During an active call, the mobile measures received signal strength indicator (RSSI) and carrier-to-interference ratio (C/I) for up to twelve neighboring channels, transmitting these via the Slow Associated Control Channel (SACCH) every second. The base station analyzes these reports along with its own measurements and, if a handover is deemed necessary due to deteriorating signal quality or load balancing, the MSC coordinates the switch by commanding the mobile to tune to the new channel using the Fast Associated Control Channel (FACCH) for rapid signaling. This procedure ensures seamless mobility support within the TDMA framework, maintaining voice quality during cell transitions.^[32] In idle mode, cell reselection allows the mobile to camp on the strongest available cell to optimize battery life and connection readiness, prioritizing the serving cell unless its RSSI or C/I falls below thresholds, at which point it evaluates neighbors based on the same metrics reported periodically. Reselection criteria emphasize the best overall signal quality to minimize unnecessary scans, with the mobile scanning broadcast channels to assess potential candidates. For inter-system mobility between D-AMPS and analog AMPS, dual-mode mobiles support reselection and handover using shared spectrum and IS-41 signaling, where the D-AMPS mobile may switch to an AMPS channel if digital coverage weakens, invoking inter-MSC coordination via SS7 messages to preserve the session. This backward compatibility enhances coverage in mixed environments without soft handover capabilities.^[32]

Deployment

Network Examples

AT&T's implementation of Digital AMPS exemplifies a large-scale overlay strategy on its legacy AMPS network, initiated in 1991 with early trials and achieving commercial availability in select markets by 1993. By 1995, the network had expanded to over 1,000 cell sites supporting D-AMPS operations, leveraging a 7-cell reuse pattern in the 800 MHz band to triple capacity per channel compared to analog while minimizing interference. This configuration allowed seamless dual-mode operation, enabling subscribers to switch between digital and analog modes for broader compatibility.^[5]^[21] U.S. Cellular's deployment highlights D-AMPS application in rural and tier-2 markets, where it was integrated with existing AMPS infrastructure to extend coverage in low-density areas. Operators like U.S. Cellular employed a 4-cell reuse pattern in these regions to improve spectrum efficiency without requiring dense site placement, supporting reliable service in challenging terrains such as the Midwest and rural South. This approach prioritized wide-area coverage over high-capacity urban designs, with base transceiver stations (BTS) configured for fewer simultaneous users but extended range.^[33] Following the 1995 FCC spectrum auctions for the PCS band, operators including AT&T extended D-AMPS to the 1900 MHz frequencies for urban capacity enhancement, deploying microcells to handle dense traffic in metropolitan areas like New York and Los Angeles. These microcell setups, with smaller cell radii of 1-2 km, allowed for higher reuse factors and supported the TDMA structure's multi-user channels, enabling up to three times more voice paths per 30 kHz carrier than AMPS.^[34] At its peak around 2000, major D-AMPS operators like AT&T provided coverage to over 70% of the U.S. population, contributing to the overall cellular coverage that reached approximately 90% across the United States, facilitated by approximately 104,000 total cell sites industry-wide. Typical BTS configurations supported 20-50 carriers per site, allowing scalability for varying traffic loads while the TDMA frame structure enabled efficient sharing among multiple users per channel.^[35]^[36]^[37]^[38]

Regional Variations

In the United States, Digital AMPS (D-AMPS) implementation was shaped by Federal Communications Commission (FCC) regulations, which mandated a dual-licensing structure dividing the 800 MHz cellular band into A-side (non-wireline carriers) and B-side (wireline carriers) blocks to foster competition.^[21] Each side was allocated 416 channels (395 voice and 21 control), with the A-side receiving channels 1–333 and the B-side 334–666, enabling independent network builds while sharing the spectrum for interoperability.^[21] This split influenced D-AMPS channel allocations during the transition from analog AMPS, as operators re-farmed spectrum starting in 1995 to deploy digital TDMA overlays without disrupting service.^[39] Additionally, the 1900 MHz Personal Communications Services (PCS) band, auctioned by the FCC from 1995 onward, was reserved exclusively for digital operations, excluding analog AMPS and accelerating D-AMPS adoption in urban areas for higher-capacity services.^[39] In Canada, D-AMPS deployment closely mirrored the U.S. model due to shared North American spectrum harmonization, with major operator Rogers Wireless launching TDMA networks in the 800 MHz and 1900 MHz bands during the mid-1990s to upgrade from analog AMPS.^[40] Unlike the U.S., where FCC rules required AMPS support until 1994–2008 depending on the market, Canadian regulations under Industry Canada imposed no such post-2000 mandate for analog compatibility, allowing faster transitions.^[41] Rogers integrated D-AMPS with emerging GSM networks in select regions starting in 2001, enabling dual-mode handsets and smoother handovers between TDMA and GSM for nationwide coverage, before fully decommissioning D-AMPS in 2007.^[40] Deployment in Latin America was more limited and varied, primarily as an upgrade path from analog AMPS in the 800 MHz band, driven by growing demand in major markets like Mexico and Brazil. In Mexico, D-AMPS/TDMA systems emerged in the mid-1990s under operators like Telcel, enhancing capacity on existing 800 MHz infrastructure amid regulatory reforms by COFETEL that ended the early duopoly and encouraged digital migration.^[42] Brazil saw D-AMPS/TDMA rollout from 1996, post-AMPS launch in 1992, with carriers like MAXITEL using the A and B band splits in the 800 MHz spectrum; privatization auctions in 1997–1998 spurred competition and upgrades.^[42] Handover mechanisms to GSM varied by operator, with some networks maintaining dual TDMA-GSM cores for interoperability during the early 2000s transition, particularly in Brazil where GSM gained traction alongside TDMA.^[43] Outside the Americas, D-AMPS adoption was rare, largely confined to isolated trials or legacy extensions, such as limited 800 MHz deployments in the Philippines influenced by U.S. ties but overshadowed by GSM's global standardization.^[42] The 1900 MHz band remained unavailable internationally, as it was a North American-specific allocation for PCS services.^[39] Regulatory preferences for GSM as the international 2G standard further diminished D-AMPS prospects elsewhere, prioritizing spectrum efficiency and roaming compatibility over regional TDMA variants.^[44]

Evolution and Successors

IS-136 Enhancements

IS-136 represented a significant upgrade to the original IS-54 standard for Digital AMPS (D-AMPS), introducing fully digital control channels and enhanced services to improve efficiency and user experience while maintaining compatibility with existing infrastructure.^[45] The standard, first introduced in 1994, enabled stand-alone TDMA handsets without reliance on analog signaling, building on the vector sum excited linear prediction (VSELP) vocoder of IS-54 as a baseline for voice encoding.^[26] Key advancements focused on control signaling, voice quality, and data capabilities, allowing networks to support more users and new applications.^[5] A major enhancement was the introduction of Short Message Service (SMS) in 1995, delivered via the Digital Control Channel (DCCH), which facilitated point-to-point and broadcast messaging up to limited character lengths.^[46] The DCCH, comprising forward (DFCC) and reverse (DRCC) components, replaced the analog control channels of IS-54 with digital time-division multiple access (TDMA) signaling at 48.6 kbit/s, enabling two-way SMS through the R-DATA transport mechanism for short alphanumeric messages.^[47] This upgrade supported faster call setup and paging by assigning mobiles to specific slots in DCCH superframes, reducing monitoring intervals compared to the 4.8-second cycles of prior analog systems and allowing devices to enter low-power sleep modes more effectively.^[48] Voice quality saw substantial improvements with the adoption of the enhanced full-rate (EFR) vocoder based on algebraic code-excited linear prediction (ACELP), standardized as IS-641, operating at 7.4 kbit/s to deliver near-wireline speech clarity in error-free conditions and greater robustness against transmission errors and interference than the IS-54 VSELP codec.^[49] The ACELP method provided enhanced perceptual quality, particularly in noisy environments, while maintaining compatibility with existing TDMA frames.^[25] Additionally, the DCCH supported short data bursts for services like over-the-air (OTA) parameter updates, allowing SIM-like provisioning of handsets without physical smart cards by transmitting configuration data directly over the air interface.^[50] Data services expanded with circuit-switched data (CSD) support at rates up to 9.6 kbit/s, utilizing the full TDMA channel bandwidth for asynchronous or synchronous connections suitable for early mobile computing and fax applications.^[5] These enhancements, including half-rate voice coding options at 4 kbit/s, enabled network operators to double channel capacity in high-traffic areas. Deployment of IS-136 features accelerated between 1996 and 1998, with major U.S. carriers like AT&T and others upgrading infrastructure to achieve up to threefold overall capacity gains over analog AMPS, and further increases via half-rate vocoders in select networks.^[46] This rollout facilitated broader adoption of digital-only handsets and paved the way for integrated PCS operations in the 1.9 GHz band.^[7]

Transition to Later Technologies

The transition from Digital AMPS (D-AMPS), based on IS-136 TDMA standards, to third-generation (3G) technologies primarily involved operators refarming spectrum and overlaying new systems rather than direct evolutionary upgrades within the D-AMPS framework. A 2.5G evolution path was provided by EDGE (Enhanced Data Rates for GSM and TDMA/136 Evolution), which standardized higher packet data rates up to 384 kbit/s while compatible with IS-136 infrastructure, though adoption remained limited.^[51] Major U.S. carriers like AT&T Wireless initiated this shift by overlaying GSM/GPRS networks on existing TDMA infrastructure starting in the late 1990s, enabling a bridge to 3G UMTS while improving data capabilities.^[52] Similarly, U.S. Cellular migrated from D-AMPS to CDMA2000, leveraging the compatibility of TDMA spectrum in the 800 MHz band for the new code-division multiple access (CDMA) overlay.^[53] Over time, this spectrum was further refarmed for 4G LTE deployments, with operators reallocating 850 MHz and 1900 MHz channels previously used for D-AMPS to support higher-capacity broadband services.^[54] Interworking between D-AMPS and emerging 3G networks relied on dual-mode handsets capable of operating across TDMA, GSM, and CDMA standards, allowing seamless handovers during the migration phase. These devices supported interoperability in overlapping coverage areas, such as handovers from D-AMPS to CDMA in cellular bands.^[55] This approach minimized service disruptions for users as operators phased out D-AMPS sites in favor of 3G base stations. Several factors drove the rapid adoption of GSM and CDMA over D-AMPS for 3G transitions. GSM's widespread global deployment facilitated international roaming and superior packet data services via GPRS, attracting operators seeking interoperability beyond North America.^[56] In contrast, CDMA offered higher spectral efficiency and voice capacity under heavy loads, providing a compelling path for U.S. carriers like U.S. Cellular to evolve to CDMA2000.^[57] Regulatory pressures from the Federal Communications Commission (FCC) in the early 2000s accelerated this shift, including mandates to identify and reallocate spectrum for 3G services, which encouraged refarming of cellular bands from legacy 2G technologies.^[58] D-AMPS's deployment was largely confined to the Americas, which simplified its replacement with regionally aligned 3G standards such as W-CDMA (UMTS) for GSM operators and CDMA2000 for others, without the complexities of global harmonization faced by European systems.^[59] This geographic limitation allowed for a more straightforward spectrum refarming process toward LTE, as North American regulators prioritized compatibility with existing infrastructure.^[60]

Phase-Out

Sunset in North America

The decommissioning of Digital AMPS (D-AMPS) networks in North America marked the end of a significant era in mobile communications, driven primarily by the need to repurpose spectrum for advanced 3G and 4G technologies. In the United States, major operators initiated shutdowns in the late 2000s. AT&T Mobility completed the phase-out of its remaining 850 MHz TDMA networks on February 18, 2008, coinciding with the FCC's analog AMPS sunset date, while its 1900 MHz markets had been discontinued earlier in 2007.^[5]^[61] Dobson Communications, acquired by AT&T, shut down its TDMA network on March 1, 2008.^[5] U.S. Cellular, the last major carrier to operate D-AMPS, terminated service on February 10, 2009, primarily in rural markets.^[5] In Canada, the transition occurred slightly earlier to align with U.S. timelines and facilitate cross-border roaming. Rogers Wireless, the primary D-AMPS operator, decommissioned its networks on May 31, 2007, migrating remaining users to GSM.^[5]^[62] Other carriers like Bell Mobility and Telus primarily used CDMA for digital services rather than TDMA, having shifted to CDMA2000 and later HSPA by the mid-2000s. Key reasons for these shutdowns included spectrum reallocation to support GSM/UMTS and CDMA2000 deployments, a sharply declining subscriber base that fell below 1% of total U.S. mobile users by 2007 due to migrations to newer standards, widespread handset obsolescence, and the expiration of FCC waivers mandating AMPS compatibility in digital networks.^[5]^[63] These factors rendered D-AMPS economically unsustainable, prompting operators to replace it with GSM or CDMA technologies.^[61] The impacts were felt most acutely by legacy users, who faced mandatory handset upgrades to compatible 3G/4G devices, and in remote rural areas where brief service disruptions occurred during transitions. By 2010, all D-AMPS networks in North America had been fully decommissioned, with no active operations remaining as of 2025.^[5] In Latin America, where D-AMPS had been deployed in countries such as Mexico and Brazil, networks were gradually phased out during the 2000s as operators migrated to GSM and CDMA2000 standards, with most shutdowns completed by the early 2010s.^[64]

Legacy Impact

Digital AMPS (D-AMPS), standardized as IS-54 and later IS-136, pioneered time-division multiple access (TDMA) technology in North America, marking the continent's initial shift to digital cellular systems in the early 1990s. Adopted by the Telecommunications Industry Association (TIA) in 1989, D-AMPS divided each 30 kHz analog AMPS channel into three time slots, effectively tripling capacity while maintaining backward compatibility with existing 1G infrastructure. This innovation influenced subsequent standards, including IS-95 CDMA, by fostering competition and shaping the dual-mode designs that allowed seamless operation in North American bands, such as the 800/900 MHz cellular and 1900 MHz PCS allocations.^[5]^[65] D-AMPS introduced mobile authentication via unique identifiers (IMSI, TMSI, ESN) and voice privacy measures using the Cellular Message Encryption Algorithm (CMEA), enhancing security over analog AMPS's vulnerabilities. These features set precedents for privacy in digital communications. Additionally, enhancements in IS-136 enabled early text messaging capabilities, serving as a precursor to short message service (SMS) and circuit-switched data at rates up to 9.6 kbit/s, which supported basic mobile data applications.^[5]^[1] In terms of industry impact, D-AMPS played a pivotal role in the U.S. analog-to-digital transition by overlaying digital channels on AMPS spectrum, allowing operators to phase out 1G service gradually without disrupting coverage. This facilitated the training and deployment of engineers familiar with TDMA principles, which informed the development of 3G technologies like cdma2000 through shared North American standardization efforts. The system's use of 850 MHz and 1900 MHz bands established a spectrum legacy that persists today, with these frequencies re-farmed for 4G LTE and 5G networks by major carriers, enabling efficient spectrum reuse via dynamic sharing techniques.^[5]^[66]^[67] By 2025, no active D-AMPS networks remain operational, with the last major shutdowns occurring in North America by 2009, rendering the technology obsolete in favor of GSM derivatives and CDMA evolutions. However, its early data services indirectly influenced later mobile ecosystems, including the Internet of Things (IoT), by demonstrating packet-like data transmission in constrained environments, which informed foundational concepts for low-bandwidth device connectivity in subsequent generations. Historical D-AMPS handsets, emblematic of early 2G design, hold collectible value among enthusiasts for their role in pioneering portable digital telephony.^[5]^[68] Globally, D-AMPS bridged the 1G-to-2G gap primarily in the Americas, where it supported regional operators from 1993 onward amid limited international adoption. In contrast to GSM's worldwide dominance—capturing over 90% market share by the mid-2010s—D-AMPS exemplified standards fragmentation, confining its footprint to North and South America and underscoring the challenges of regional silos in early mobile evolution.^[5]

References

[1]
IS-136 Technology - Rohde & Schwarz
IS-136 is an evolution of the IS-54 standard. Both are known as Digital AMPS (D-AMPS), a 2G technology used particularly in the United States and Canada.
[2]
None
Summary of each segment:
[3]
None
Below is a merged summary of the IS-136 TDMA Technology segments, combining all provided information into a concise yet comprehensive response. To handle the dense technical and historical details efficiently, I’ve incorporated tables in CSV format where appropriate (e.g., for technical specifications and deployment history). The response retains all key points from the individual summaries while eliminating redundancy and organizing the content for clarity.
[4]
[PDF] A Comparative Study of Three TDMA Digital Cellular Mobile ...
D- AMPS (IS-54 and IS-136) VSELP specifies an encoding of each 20 ms of speech into 159-bit frames, thus achieving a raw data rate of 7.95 kbit/s. In an actual ...
[5]
The First Digital Cellular Systems – TDMA, GSM and iDEN (2G)
IS-54 and IS-136 are second-generation (2G) mobile phone systems, known as Digital AMPS (D-AMPS), and a further development of the North American 1G mobile ...
[6]
IS-54 and IS-136 (Digital AMPS)
IS-54 and IS-136 (Digital AMPS). IS-54 is the standard for the digital version of the US AMPS system. Recently IS-54 has been replaced by the IS-136 standard.
[7]
[PDF] IS-136 TDMA Technology, Economics, and Services
The IS-136 TDMA standard combines digital TDMA and AMPS technolo- gies. In 1990, the first TDMA digital systems were introduced in North. America. Today ...
[8]
Definition of IS-136 | PCMag
(Interim Standard-136) The second generation of the TDMA digital cellular system. TDMA operates in North America in the 800 MHz band and 1.9 GHz PCS band.
[9]
IS-54 D-AMPS - Signal Identification Wiki
Sep 2, 2025 · D-AMPS, also known as IS-54 and IS-136, is a second generation (2G) mobile phone system standard which develops on analog AMPS, a 1G standard.
[10]
IS-54 Digital AMPS - Cellular History
IS-54 was not a completely new standard like GSM. It was based 100% on analog AMPS. It was a standard that allowed analog AMPS and the new digital AMPS to ...Missing: D- | Show results with:D-
[11]
[PDF] Wireless Cellular Networks: 1G and 2G
IS-54 has analog control channel for compatibility with AMPS. Did not succeed. Page 20. 7-20. ©2006 Raj Jain.Missing: backward | Show results with:backward
[12]
[PDF] NADC IS/54-136 TDMA Digital Cellular - Manuals.plus
Jan 31, 1996 · By using TDMA instead of FDMA, IS-54/-136 increases the number of users from 1 to 3 per channel (up to 10 with enhanced. TDMA). The IS-54 ...
[13]
TR45-3 Appendix A to IS-54 Rev. B Dual-Mode Cellular System ...
Authentication, Message Encryption, Voice Privacy Mask Generation, Shared Secret Data Generation, A-Key Verification, and Test Data. February 1992.
[14]
[PDF] Recent Advances in Cellular Wireless Communications
During the development of IS-54, the major constraints were to provide a substantial increase in system capacity while sustaining backward compatibility with ...
[15]
NEW TECHNOLOGIES, STANDARDS, CUSTOMERS, AND ...
In January 1992 the CTIA's board of directors adopted a resolution that reaffirmed the role of D- AMPS (TDMA) as the industry standard but also opened the door ...
[16]
[PDF] Mobile telephone history
The TIA next wrote a standard for this new digital system, soon to be called. IS-54. It was unofficially called D-AMPS or Digital. AMPS. After publishing the ...
[17]
The history of UMTS and 3G development
October 13 1983 First commercial operation of AMPS (AT&T's Illinois Bell, Chicago) ... 1994 Commercial operation of D-AMPS (IS-54) in US started; 1994 ...
[18]
AT&T ROLLS `PCS' INTO CELL LAUNCH - RCR Wireless News
Oct 7, 1996 · Monthly service rates for the new AT&T PCS digital cellular service start at $25, and national roaming rates anywhere in the United States will ...
[19]
U.S. Cell Phone Subscriptions - Stable Isotope Foundation
Industry data for U.S. cell phone subscriptions 1983-2013 ; 1992. 11,032,753 ; 1993. 16,009,461 ; 1994. 24,134,421 ; 1995. 33,785,661 ; 1996. 44,042,992.
[20]
[PDF] The Cellular Concept— System Design Fundamentals
Dec 4, 2001 · Out of the 416 channels used by each operator, 395 are voice channels and the remaining 21 are control channels. Channels 1 through 312 (voice.
[21]
[PDF] Fundamentals of Cellular Networks - University of Pittsburgh
Sectored Frequency Planning. • Example: Allocate frequencies for a AMPS operator in cellular. B-block who uses a 7 cell frequency reuse pattern with 3 sectors.
[22]
[PDF] Comparisons Between USDC (IS-54) and GSM - ThaiScience
Since each channel bandwidth is divided into time slots, many users can be supported by one channel bandwidth; thus, the capacity of the system is increased.
[23]
[PDF] Modulation, Transmitters and Receivers - UCSB ECE
The π/4-DQPSK modulation scheme is a differentially encoded form of π/4-. QPSK. The π/4-DQPSK scheme incorporates the π/4-QPSK modulator and an encoding ...
[24]
Enhanced full rate speech codec for IS-136 digital cellular system
Aug 6, 2025 · An AMR speech codec utilises the Algebraic Code Excitation Linear Prediction (ACELP) algorithm that has also been employed in GSM EFR [9] ...
[25]
What Is IS-136? - Technical Support Knowledge Center Open
IS-136 is a mobile communications interim standard which extends the functions of the dual-mode system standard IS-54B. IS-54B is also known as NADC/TDMA ...
[26]
https://docs.keysight.com/kkbopen/what-is-is-136-589737757.html
[27]
https://ieeexplore.ieee.org/document/778435
[28]
[PDF] APPLICANT: Lucent Technologies EXHIBIT 3 FCC ID
To access a digital cellular network, an IS-136 mobile must first access a DCCH. The "Access Threshold"of a cell site is a parameter that is used to determine.
[29]
GLOSSARY | McGraw-Hill Education - Access Engineering
The CAVE algorithms make use of the MIN, ESN, A-key, and SSD values to generate authentication results that determine the legitimacy of a mobile station.
[30]
D-AMPS | ANSI-136 | IS-136 - Telecom ABC
IS-136 provides voice and data services with a maximum bit rate of 8 kbit/s and a short messaging service.
[31]
[PDF] Mobile Wireless Communications
This book provides a tutorial introduction to digital mobile wireless networks, illustrating theoretical underpinnings with a wide range of real-world examples.
[32]
U.S. Cellular Corporation - Company-Histories.com
This team was responsible for the selection of cell sites, construction of towers, installation of operating systems, establishment of business offices, and ...
[33]
[PDF] migration to imt-2000 systems - ITU
From TDMA/D-AMPS systems ... in the personal communications services (PCS) bands (1800 MHz and 1900 MHz).
[34]
[XLS] Cellular Telecommunications Industry - Census.gov
Cell sites \1, Number, 5,616, 7,847, 10,307, 12,805, 17,920, 22,663, 30,045, 51,600 ... When a wireless PCS or cellular phone moves from one cell toward another ...
[35]
[PDF] Federal Communications Commission FCC 04-22
Section 22.901(d) specifically requires that carriers make mobile services available to subscribers whose mobile equipment conforms to the AMPS compatibility ...
[36]
[PDF] FCC Broadband PCS Band Plan
Note: Some of the original C Block licenses (Originally 30 MHz each) were split into multiplelicenses (C-1 and C-2, 15 MHz; C-3, C-4, and C-5 10 MHz).
[37]
Remaining TDMA and Analogue Subscribers Already Moved to GSM
May 3, 2007 · On January 10, 2007, Rogers announced that it would be turning down its older TDMA and analogue networks effective May 31, 2007 and move the ...
[38]
CPC-3-24-01 — Administrative Monetary Penalties (AMPs) Under ...
Jun 10, 2024 · The intent of this document is to inform Canadians of how administrative monetary penalties (AMPs) are determined by Innovation, Science and ...
[39]
[PDF] Cellular: An Economic and Business History of the International ...
AMPS standard operated in frequency bands between 800 MHz and 900. MHz ... Finally, we study two countries in Latin America, Mexico and Brazil, where ...
[40]
[PDF] Managing a TDMA-GSM Dual Network - 3GSM Americas 2002
D-AMPS. GSM *. Moving to GSM. Entel (Bolivia) ... Form Latin America: 3 Million people (~30% GSM) ... Mexico and Central America: ~13,500. Colombia/Peru ...
[41]
https://ised-isde.canada.ca/site/spectrum-management-telecommunications/en/learn-more/key-documents/procedures/client-procedures-circulars-cpc/cpc-3-24-01-administrative-monetary-penalties-amps-under-radiocommunication-act-guidance
[42]
IS-136 Technology - Rohde & Schwarz
IS-136, also known as TDMA, is a 2G D-AMPS technology, an evolution of IS-54, that uses 30 kHz bands and triples voice capacity.Missing: enhancements | Show results with:enhancements
[43]
(PDF) A Comparative Study of Three TDMA Digital Cellular Mobile ...
Aug 6, 2025 · The second phase standard is IS-136 which implements digital call set-up channels to enable stand-alone TDMA handsets. IS-136 has ...
[44]
[PDF] Impact of Mobile-Originated Short Message Service on the Digital ...
This paper evaluates the capacity of the ANSI-136 digital control channel (DCCH) uplink to carry high volumes of mobile-originated short message service (MO ...
[45]
[PDF] Personal Communications Service (PCS)
The DCCH forms the core of the IS–136 specification and is the primary enhancement to TDMA digital-wireless technology. It is a new control-channel.
[46]
https://www.researchgate.net/publication/275605420_A_Comparative_Study_of_Three_TDMA_Digital_Cellular_Mobile_Systems_GSM_IS-136_NA-TDMA_and_PDC_Based_On_Radio_Aspect
[47]
https://www.cin.ufpe.br/~nomadic/vtc2000/A88672.PDF
[48]
[PDF] Migration to 3G Technology Standards: A Comparison of Selected ...
AT&T Wireless is overlaying GSM/GPRS on its TDMA network to improve its wireless data capabilities and enhance its migration to 3G technology.
[49]
cdma2000-1x EV-DO Wireless Networks: Technology Overview
This technical brief will introduce the reader to cdma2000 1xEV-DO wireless network concepts and will provide understanding and insight into the air interface.
[50]
[PDF] Evolution of Cellular Technologies
Aug 4, 2010 · AMPS was developed by AT&T Bell Labs in the late 1970s ... – Ability to deploy in existing spectrum and reuse cell sites and transmission.
[51]
[PDF] M.1073-1 - Digital cellular land mobile telecommunication systems
System specifications are summarized in Table 1. Since the standard is compatible with existing AMPS systems, only the digital features are highlighted here.<|control11|><|separator|>
[52]
GSM vs. CDMA: Understanding the 10 Key Differences - Spiceworks
Jun 24, 2022 · CDMA, when compared to the GSM, lacks international roaming capabilities. 2. SIM usage. With GSM, you can swap SIM cards if your phone is ...
[53]
GSM and CDMA - How Cell Phones Work | HowStuffWorks
GSM operates in the 900-MHz and 1800-MHz bands in Europe and Asia and in the 850-MHz and 1900-MHz (sometimes referred to as 1.9-GHz) band in the United States.
[54]
Plan to Select Spectrum for Third Generation (3G) Wireless Systems
Oct 20, 2000 · D. Final Report. The FCC and NTIA will release their final reports on March 30, 2001, describing all identified bands for 3G wireless use. ...Missing: AMPS | Show results with:AMPS
[55]
[PDF] The Evolution of Mobile Technologies: 1G 2G 3G 4G LTE
Jun 1, 2014 · D-AMPS, GSM/GPRS,. cdmaOne. Mobile 3G. CDMA2000/EV-DO,. WCDMA/HSPA+, TD ... WCDMA (UMTS). Uses 5 MHz carrier; leverages GSM core network.Missing: transition | Show results with:transition
[56]
Spectrum Refarming – Radio Frequency Optimization Notes
Dec 12, 2022 · The allocation of spectrum that was once used by one technology to allocate bandwidth for another technology is called spectrum refarming.
[57]
AT&T begins shutdown of AMPS and TDMA networks - Engadget
Jun 21, 2007 · So far, AT&T has announced TDMA / AMPS network shutdowns in 18 markets by the end of 2007 and every other market in 2008. A good explanation ...Missing: Digital D- Dobson Canada Rogers
[58]
Rogers issues wireless reminder: It's shutting off its old network on ...
May 3, 2007 · On January 10, 2007, Rogers announced that it would be "turning down" its older TDMA and analog networks effective May 31, 2007 and move the ...
[59]
Analog Cellular (AMPS) (1G) - Telephone World
Jan 17, 2021 · The first system was successfully deployed in Chicago, Illinois, in 1979. ... AMPS and D-AMPS were phased out in favor of either CDMA2000 ...Missing: cities | Show results with:cities
[60]
Gadgets affected by analog shutdown - Denver - 9News
Dec 22, 2007 · DENVER - Carriers will start shutting down the country's oldest cellular network, for analog devices, in February.Missing: 2010 emergency
[61]
[PDF] IS-95 CDMA - University of Pittsburgh
carrier band edge and an AMPS or TDMA carrier is 270. KHz => 9 AMPS channels ... • Security: CDMA signal + CAVE encryption. • Air Interface Standard Only.Missing: legacy contributions North precursor
[62]
[PDF] America's 5G Era - RAND
*Carrier Spectrum Holdings: AT&T: 700 MHz (FirstNet), 850 MHz (CLR, n5), 1700/2100 MHz (AWS), 1900 MHz (PCS), 2300 MHz (WCS), 24 GHz (n258), 39GHz. (n260); ...<|control11|><|separator|>
[63]
[PDF] 3G Wireless Networks - Access Engineering
This stage in the evolution was known as IS-54 B. (also known as Digital AMPS or D-AMPS) and it obviously gives a signifi- cant capacity boost compared to ...
[64]
A Timeline from 1G to 5G: The Evolution of Mobile Communication
Aug 11, 2023 · These early mobile networks that we would now refer to as 1G, used analogue technology and examples included AMPS (Advanced Mobile Phone System) ...