Fact-checked by Grok 2 weeks ago

Overpressure

Overpressure is the transient increase in pressure above the ambient atmospheric level, typically generated by a shock wave from an explosion or other rapid energy release, which can cause significant damage to structures, equipment, and human tissues.^[1] This phenomenon, often referred to as blast overpressure, arises from the sudden expansion of gases in explosions such as detonations or deflagrations, propagating as a pressure wave—supersonic in detonations—that decays with distance and time.^[2]^[3] In engineering and safety contexts, overpressure is a critical parameter for assessing explosion risks, with peak values measured in units such as psi (pounds per square inch) or kPa, and its effects modeled using empirical equations like those in the Unified Facilities Criteria (UFC) for predicting structural vulnerabilities.^[4] The blast wave associated with overpressure consists of a positive phase of compression followed by a negative phase of rarefaction, with the positive phase delivering the primary destructive force through peak incident and reflected pressures.^[2] Effects on humans vary by exposure level: at 1.0 psi, typical glass failure can cause lacerations; 3.5 psi leads to serious injuries like eardrum rupture; and levels above 14.5 psi result in high fatality rates from lung damage and whole-body trauma.^[1] For structures, overpressures of 0.15–0.22 psi shatter windows, while 5.0–7.0 psi cause near-total destruction of residential buildings, informing blast-resistant design in military and industrial applications.^[2] In addition to explosive contexts, overpressure appears in geophysics as excess pore fluid pressure in subsurface formations exceeding hydrostatic equilibrium, which influences seismic wave propagation, rock stability, and drilling hazards in oil and gas exploration.^[5] This geological overpressure, often caused by rapid sedimentation or hydrocarbon generation, can be predicted using well logs and seismic data to mitigate risks like blowouts.^[6] Overall, understanding and mitigating overpressure is essential across physics, engineering, and earth sciences for safety and risk management.^[4]

Definition and Fundamentals

Definition

Overpressure, denoted as ΔP, refers to the difference between the absolute pressure in a system and the ambient atmospheric pressure.^[7] This excess pressure arises when a localized region experiences a transient or sustained elevation beyond normal conditions, often manifesting as a dynamic wave or static buildup.^[4] In physical terms, it quantifies the deviation from equilibrium, where ΔP > 0 indicates compression relative to the surroundings.^[8] The phenomenon occurs in various contexts, such as the propagation of shock waves from explosive detonations, where rapid energy release compresses surrounding air, or in confined vessels where chemical reactions or thermal expansion lead to pressure accumulation. In geophysics, overpressure describes excess pore fluid pressure in geological formations that exceeds hydrostatic equilibrium, influencing seismic activity and drilling operations.^[5] In blast scenarios, overpressure forms the leading edge of a shock front, while in industrial processes, it signals potential hazards from uncontrolled volume changes.^[9] These occurrences highlight overpressure's role as a key indicator of energetic disturbances in both open and enclosed environments.^[1] Overpressure aligns closely with gauge pressure, which measures pressure relative to atmospheric conditions (P_gauge = P_absolute - P_atmospheric), distinguishing it from absolute pressure that includes the full atmospheric contribution from a perfect vacuum reference.^[10] While the terms are often used interchangeably in non-vacuum contexts, overpressure specifically emphasizes transient excesses, such as those in blast waves, whereas absolute pressure provides a total value independent of ambient variations.^[11] Overpressure levels above certain thresholds can lead to physiological and structural damage, as explored in dedicated sections on physical effects.

Units and Measurement

Overpressure, defined as the pressure differential ΔP above ambient atmospheric pressure, is quantified using standardized units to facilitate consistent measurement and comparison across applications. The primary unit in the International System of Units (SI) is the pascal (Pa), equivalent to one newton per square meter (N/m²), which allows precise expression of pressure changes in scientific and engineering contexts.^[12] Other widely adopted units include the pound per square inch (psi) in imperial systems, the bar (1 bar = 100,000 Pa), and the atmosphere (atm; 1 atm ≈ 101,325 Pa), particularly in blast engineering where psi is common for its historical use in military and industrial assessments.^[4] Standard conversions between these units are essential for interoperability; for instance, 1 psi ≈ 6.895 kilopascals (kPa), 1 bar = 100 kPa, and 1 atm ≈ 14.696 psi.^[13] Detection of overpressure relies on specialized instrumentation capable of capturing rapid, dynamic pressure waves. Piezoelectric sensors, which generate an electrical charge in response to mechanical stress, are frequently used for high-speed blast measurements due to their sensitivity to transient events.^[14] Pressure transducers, including piezoresistive variants that measure strain via resistance changes, provide robust data in field tests, while dedicated blast gauges—such as wearable systems with multiple sensors—enable real-time monitoring during explosive simulations.^[15]^[16] Threshold values serve to classify overpressure magnitudes for risk assessment and design purposes, with examples including 1 psi (≈6.9 kPa) as a benchmark for initial structural vulnerability and 100 kPa (≈14.5 psi) for higher severity classifications.^[1] To maintain measurement reliability, these devices undergo calibration per international standards, such as ISO/IEC 17025, which accredits laboratories to achieve accuracies typically within ±0.05% of reading or better, ensuring traceability to national metrology institutes.^[17] ASTM E74 further outlines verification procedures for transducer performance under load, supporting precise quantification in dynamic environments.^[18]

Causes of Overpressure

Explosive Events

Overpressure in explosive events primarily results from the rapid chemical or nuclear reaction that releases a large amount of energy, rapidly expanding gases and compressing the surrounding air to form a supersonic shock front known as a blast wave. This shock front propagates outward in all directions, creating a transient pressure increase above ambient atmospheric levels, typically described by a sharp rise to peak overpressure followed by an exponential decay in the positive phase and a subsequent negative phase of sub-ambient pressure.^[19]^[20] Explosives generating such overpressure are categorized into high and low types based on their reaction velocity. High explosives, like trinitrotoluene (TNT), undergo detonation—a supersonic reaction that produces intense shock waves and substantial overpressure through abrupt gas expansion, commonly employed in conventional bombs and munitions. In contrast, low explosives deflagrate subsonically, yielding comparatively weaker pressure waves due to slower combustion. Nuclear detonations exemplify extreme high-energy events, where fission or fusion reactions liberate immense thermal and mechanical energy, driving blast waves with overpressures orders of magnitude greater than chemical explosives.^[21]^[22] The magnitude of blast overpressure varies with several key factors, including the explosive charge size (which determines total energy release), standoff distance from the detonation (with overpressure decaying rapidly as distance increases), and atmospheric conditions such as temperature and humidity that influence wave propagation and dissipation. Higher temperatures can accelerate wave speed, while elevated humidity may attenuate low-pressure components through moisture absorption.^[19]^[23] To account for charge size variations and enable consistent prediction of blast effects, engineers employ the scaled distance concept, defined as Z = \frac{R}{W^{1/3}}, where R is the standoff distance in meters and W is the explosive yield in kilograms of TNT equivalent. This cube-root scaling, derived from the Hopkinson-Cranz law, normalizes overpressure values, allowing effects from different-sized detonations to be compared at equivalent scaled distances.^[24]

Confined or Enclosed Environments

In confined or enclosed environments, overpressure arises primarily from the rapid gas expansion generated by chemical reactions, such as combustion, within a restricted volume where the expanding gases cannot readily dissipate. This process begins with the ignition of a fuel-air mixture, leading to a deflagration that accelerates due to confinement, causing a buildup of heat and pressure until the enclosure ruptures or vents. Unlike unconfined explosive events, the enclosed setting amplifies the pressure through repeated reflections of shock waves and limited escape paths for combustion products.^[25]^[26]^[27] Common examples include boiler explosions, where overheating or fuel malfunctions cause steam and gas expansion in sealed vessels, resulting in catastrophic pressure surges. Dust explosions in silos occur when combustible particulates, such as grain dust, suspend in air and ignite, producing intense pressure rises in the confined structure. Similarly, gas leaks in buildings can form explosive mixtures that, upon ignition, generate overpressure through combustion in rooms or enclosures.^[28]^[29]^[30]^[31]^[32] The development of overpressure in these scenarios depends on several key parameters, including the volume of the enclosure, which limits gas expansion and intensifies pressure buildup. The fuel-air mixture ratio critically influences the reaction intensity, with optimal concentrations yielding maximum overpressure. Ignition source strength determines the initial energy input, while venting efficiency affects how effectively pressure is relieved before rupture.^[33]^[34]^[35] A primary mitigation approach involves venting systems, such as blowout panels, which are designed to activate at predetermined pressures to release expanding gases and reduce the risk of enclosure failure. These panels enhance safety by directing combustion products away from the confined space, though their effectiveness relies on proper sizing relative to the enclosure volume and reaction potential.^[36]^[37]

Physical Effects

On Human Physiology

Overpressure from explosive events primarily affects the human body through direct mechanical forces on gas-filled organs, leading to barotrauma. The ear is particularly vulnerable, with tympanic membrane perforation occurring at overpressures as low as 5 psi (34 kPa), affecting approximately 1% of exposed individuals, and reaching nearly 100% incidence at 15-45 psi (103-310 kPa).^[38] Blast lung, or pulmonary barotrauma, results from rapid pressure differentials causing alveolar rupture, hemorrhage, and potential pneumothorax; the injury threshold is approximately 15 psi (103 kPa), though milder damage such as contusions may begin around 80-100 kPa (12-15 psi) depending on exposure duration and individual factors.^[38] Traumatic brain injury (TBI) can also arise as a primary effect, where the blast wave induces shear stresses and cavitation in brain tissue, leading to diffuse axonal injury even at lower overpressures of about 100 kPa in animal models, with human thresholds likely similar for mild cases.^[39] Secondary effects of overpressure involve acceleration forces from the blast wind, which can displace organs relative to the body, exacerbating internal injuries such as contusions or lacerations in the lungs and abdomen. These forces, occurring post-peak overpressure, contribute to organ shearing at thresholds around 40 kPa for initial lung displacement damage, highlighting the role of impulse (pressure integrated over time) in severity. Tertiary effects manifest as blunt trauma when individuals are thrown by the blast, resulting in fractures, concussions, or internal bleeding; while primarily due to displacement, the initiating overpressure must exceed 5-10 psi to generate sufficient wind speeds for such projection.^[2] Vulnerability to overpressure injuries varies with body orientation relative to the blast wave, as frontal exposure maximizes pressure transmission to the torso and head, increasing risk of pulmonary and cerebral damage compared to side or prone positions. Protective gear mitigates these effects; for instance, helmets can reduce head acceleration and TBI incidence by 20-50% through wave deflection, while body armor attenuates chest overpressure by factors up to 14, lowering pulmonary barotrauma risk.^[40]

On Structures and Materials

Overpressure from blast waves exerts significant mechanical loads on structures and materials, leading to failure through deformation, fracture, or collapse depending on the peak pressure, impulse duration, and material properties. Structures such as buildings and vehicles experience these loads as external pressures that can cause localized or global damage, with thresholds varying by construction type. For instance, unreinforced masonry and wood-framed buildings are particularly vulnerable to low-level overpressures, while steel and reinforced concrete offer greater resistance but can still fail under higher intensities.^[1]^[2] Damage levels to structures are well-characterized by overpressure thresholds in pounds per square inch (psi). Window breakage, a common initial failure mode, occurs at 0.5-1.0 psi, where glass shatters and frames may sustain minor damage, potentially generating hazardous fragments. Wall collapse typically begins at 5-10 psi, with partial failure of concrete block or unreinforced walls and serious deformation in steel-framed elements; for example, 4-7 psi causes buckling in steel frames, while 6-9 psi leads to severe cracking in reinforced concrete. Total destruction of most buildings, including collapse of multi-story structures, is probable above 10-12 psi, though complete devastation exceeding 20 psi can pulverize heavily reinforced facilities. These thresholds establish critical scales for assessing blast vulnerability, with lower values affecting lightweight components and higher ones targeting load-bearing elements. Injury severity and structural response also depend on blast impulse (pressure integrated over time), which incorporates duration effects.^[1]^[2] Materials respond differently to overpressure due to their inherent properties, influencing failure mechanisms. Glass, a brittle material, undergoes sudden tensile failure under blast loading, fracturing into shards at low strains without significant energy absorption, as its dynamic strength under blast is governed by maximum principal stress around 11,600-16,000 psi (80-110 MPa). In contrast, steel exhibits ductile deformation, allowing plastic yielding and energy dissipation through large strains before rupture, which enhances overall structural robustness under impulsive loads. Repeated overpressure exposures can induce fatigue in steel components, where cyclic loading from multiple blasts accumulates micro-damage, reducing ductility and increasing crack propagation risk over time.^[41]^[42] The nature of overpressure loading on structures is classified by duration relative to the element's natural period of vibration (T), affecting response regimes. Quasi-static loading occurs when the positive phase duration (t_d) greatly exceeds T (t_d/T > 40), treating the blast as a slowly varying pressure similar to static wind, leading to uniform deformation without inertial amplification. Dynamic loading prevails in intermediate cases (0.4 < t_d/T < 40), where the blast impulse excites resonant vibrations, combining pressure peak and duration to cause amplified oscillations and potential fatigue. These distinctions guide engineering analysis, with blasts often falling into dynamic or impulsive categories for urban scenarios.^[41] Historical events illustrate these effects vividly. The 1995 Oklahoma City bombing, involving a 4,800-pound ammonium nitrate-fuel oil device, generated overpressures exceeding 10 psi near the Alfred P. Murrah Federal Building, causing partial collapse of its reinforced concrete facade and total destruction of adjacent wood-framed structures within 100 feet, while shattering windows up to 3 miles away. Similarly, the 1917 Halifax Explosion, equivalent to 2.9 kilotons of TNT, produced overpressures that demolished 1,600 buildings across 2 square kilometers, collapsing brick walls and steel-framed warehouses in the North End district due to peak pressures estimated in the hundreds of psi at the epicenter. These incidents highlight overpressure's role in progressive failure, where initial envelope breaches exacerbate internal damage.^[2]^[43]

Calculation and Prediction

General Principles

Overpressure, denoted as \Delta P, is defined as the difference between the absolute pressure P in a system or wave and the ambient atmospheric pressure P_\text{atm}, such that \Delta P = P - P_\text{atm}. This quantity represents the excess pressure that can lead to mechanical effects in various scenarios, such as blast waves or confined gas expansions. In contexts involving pressure buildup, such as in vessels or enclosures, the ideal gas law PV = nRT provides a foundational relation, where an increase in temperature T or number of moles n at constant volume V results in elevated pressure P, thereby generating overpressure \Delta P relative to the initial atmospheric conditions. For instance, in overpressurized vessels, calculations of pressure rise often apply the isothermal form P_1 V_1 = P_2 V_2 derived from the ideal gas law to estimate \Delta P based on volume changes or gas accumulation. A key metric associated with overpressure is the impulse I, which quantifies the momentum transfer imparted by the pressure wave over its duration and is given by the time integral I = \int \Delta P \, dt. This integral captures the cumulative effect of the overpressure profile, where higher peak \Delta P or longer positive-phase duration increases I, influencing structural loading and injury potential in blast scenarios. Impulse is particularly useful for assessing the dynamic response of targets, as it relates directly to the velocity change induced in objects exposed to the wave. Overpressure waves propagate through air as compressional disturbances, traveling at the speed of sound, approximately 343 m/s under standard conditions of 20°C and 1 atm. For spherical waves in free space, the overpressure amplitude decays inversely with distance r from the source according to the geometric spreading law \Delta P \propto 1/r, reflecting the expansion of the wavefront over an increasing surface area. This decay assumes unobstructed propagation and holds well for acoustic or weak shock waves before additional nonlinear or atmospheric absorption effects dominate at greater ranges. Mathematical models of overpressure propagation often rely on assumptions of isentropic flow, where entropy remains constant along streamlines, allowing the use of relations like P / \rho^\gamma = \text{constant} (with \gamma as the specific heat ratio) to describe adiabatic expansions and compressions without heat transfer or irreversibilities. For low overpressures, typically below 10% of ambient, linearity is assumed, treating the wave as a small perturbation where acoustic approximations apply, and the wave equation simplifies to the linear form \nabla^2 p - \frac{1}{c^2} \frac{\partial^2 p}{\partial t^2} = 0 (with p as pressure perturbation and c as sound speed). These assumptions enable simplified derivations but require validation against nonlinear effects in high-intensity cases.

Specific Models for Explosions

The Kingery-Bulmash model is an empirical framework widely used to predict peak incident overpressure from high explosive detonations in open, free-air environments, particularly for hemispherical surface bursts. Developed from extensive experimental data on TNT charges ranging from less than 1 kg to over 400,000 kg, the model expresses peak side-on overpressure P_s as a function of the scaled distance Z = \frac{R}{W^{1/3}}, where R is the standoff distance in meters and W is the explosive yield in kilograms of TNT equivalent. The relationship is captured through polynomial curve fits, typically of the form \log(P_s) = K_0 + K_1 \log(Z) + \sum_{i=0}^{n} C_i Z^i, with coefficients varying by range of Z (e.g., 0.05 to 40 m/kg^{1/3}). For instance, at Z = 1 m/kg^{1/3}, the model predicts P_s \approx [1900](/page/1900) kPa, illustrating the rapid decay of pressure with distance in the near field.^[44]^[45] To describe the temporal profile of the blast wave, the Friedlander waveform provides a simplified analytical representation of the positive-phase overpressure history in ideal free-air conditions. The equation is given by

\Delta P(t) = P_s \left(1 - \frac{t}{t_+}\right) e^{-t/t_+},

where \Delta P(t) is the overpressure at time t, P_s is the peak overpressure, and t_+ is the positive-phase duration, often empirically related to Z via Kingery-Bulmash parameters. This form captures the initial sharp rise to P_s followed by an exponential decay, approximating the self-similar structure of strong shock waves from high explosives. The model assumes an ideal blast without significant drag or dissipation effects dominant in the far field.^[46]^[47] Standardization across different explosives relies on TNT equivalence, which converts the energy release of a given explosive to an equivalent mass of TNT based on relative detonation performance and blast output. This factor, typically 0.5–1.5 for common high explosives like C-4 or Composition B, allows non-TNT yields to be input into models like Kingery-Bulmash for consistent predictions of overpressure and impulse. Equivalence is determined experimentally, accounting for differences in detonation velocity, density, and heat of explosion, ensuring scalability via Hopkinson-Cranz scaling laws.^[48]^[49] Despite their utility, these models have limitations inherent to their empirical basis on TNT surface bursts. They are optimized for high explosives in unobstructed open air and may overestimate or underestimate pressures for low explosives with slower deflagration rates. In the close-in region (Z < 0.4 m/kg^{1/3}), predictions can deviate due to non-ideal effects like high temperatures and incomplete scaling. Additionally, the models assume free-field propagation and do not inherently include enhancements from surface reflections or urban geometries, necessitating multiplicative adjustments (e.g., up to 2–8 times higher pressures) for such scenarios.^[44]^[50]^[45]

Models for Enclosed Spaces

In enclosed spaces, overpressure from combustion events can be estimated using the ideal gas law applied to the production of gaseous products. The pressure rise \Delta P is given by \Delta P = \frac{\Delta n R T}{V}, where \Delta n represents the change in moles of gas due to combustion, [R](/page/R) is the gas constant, [T](/page/Temperature) is the temperature, and [V](/page/Volume) is the enclosure volume.^[51] This equation assumes a constant-volume process and provides a foundational calculation for the maximum overpressure in deflagrations, where the increase in gas moles from fuel oxidation drives the pressure buildup.^[51] For dust explosions in confined environments, the deflagration index K_g quantifies the rate of pressure rise associated with flame propagation through dust clouds. This index, measured in bar·m/s, characterizes the violence of the deflagration and is integral to hazard assessment in guidelines such as VDI 2263, which outlines testing protocols for dust explosibility in enclosed volumes.^[52] Higher K_g values indicate faster flame speeds and more rapid overpressure development, influencing the design of protective measures in industrial settings like silos or vessels.^[52] Venting models mitigate overpressure by allowing explosive combustion products to escape through relief areas, with calculations focused on determining the required vent area A_v to keep \Delta P below the enclosure's structural strength. Under EN 14491, the effective vent area A is computed using empirical equations incorporating volume V, maximum explosion pressure p_{max}, reduced explosion pressure p_{red,max}, static activation pressure p_{stat}, and K_{St} (a dust-specific deflagration index analogous to K_g), such as A = B \times (1 + \log(L/D)) where B is a function of these parameters.^[53] Nomograms derived from these models graphically aid in selecting A_v, accounting for venting efficiency E_f via A_v = A / E_f, and are particularly useful for preliminary sizing in dust-handling equipment to prevent rupture.^[53] These approaches extend general principles by emphasizing confinement effects, differing from unconfined explosion models that prioritize blast wave decay.^[54] A representative example is a dust explosion in a 100 m³ silo without venting, where combustible dust ignition can generate a maximum overpressure of approximately 8 bar, exceeding typical structural limits and risking catastrophic failure.^[55]

Applications and Mitigation

In Military and Safety Engineering

In military applications, overpressure calculations are integral to weapon design, particularly for determining blast radii and ensuring controlled effects of munitions. For instance, engineers at the U.S. Army DEVCOM Armaments Center optimize muzzle brake designs on howitzers to reduce blast overpressure exposure to personnel, using numerical simulations to balance recoil reduction with safety thresholds.^[56] Similarly, tools like the Department of Defense Explosives Safety Board's Blast Effects Computer aid in predicting peak overpressure from explosions, supporting munitions development and range safety by modeling shock wave propagation.^[57] Post-World War II advancements in bunker hardening focused on enhancing resistance to blast overpressure through earth-covered magazines (ECMs) and reinforced concrete structures. The ESKIMO test series (1963–1985) evaluated steel-arch ECMs under simulated explosions up to 350,000 pounds of tritonal equivalent, confirming designs that withstand impulses of 1,100 psi-ms with minimal damage and reduced quantity-distance separations, such as side-to-side spacings of 1.25W^(1/3) feet.^[58] These efforts built on earlier post-World War II tests at sites like the Arco Naval Proving Ground in Idaho, shifting from vulnerable aboveground storage to ECMs capable of 3–7 psi overpressure resistance, as seen in high-performance magazines storing up to 240,000 pounds of net explosive weight.^[58] Safety standards in industrial settings incorporate overpressure mitigation to prevent deflagration hazards in explosive atmospheres. In the United States, NFPA 68 provides guidelines for explosion protection by deflagration venting, specifying the design and installation of vents to release combustion gases and limit reduced overpressure to safe levels, thereby minimizing structural damage in enclosures like dust collectors.^[59] In Europe, the ATEX Directive 2014/34/EU mandates pressure-relief systems in protective equipment for explosive atmospheres, requiring devices that channel explosion flames and pressures away from personnel while ensuring structural integrity against internal bursts.^[60] Risk assessment in safety engineering employs probabilistic models like fault tree analysis (FTA) to quantify overpressure event probabilities. FTA constructs logical diagrams linking top events, such as overpressurization in high-pressure systems, to basic failures like valve malfunctions or operator errors, enabling the calculation of occurrence frequencies for preventive measures in facilities like fertilizer plants.^[61] This approach, as outlined in nuclear regulatory handbooks, supports quantitative risk evaluations by assigning probabilities to failure paths, prioritizing high-impact contributors.^[62] The 1988 Piper Alpha disaster exemplifies confined explosion failures due to inadequate overpressure management. An initial gas release in a module led to an explosion, generating overpressure that overwhelmed firewalls designed only for fire, not blast, resulting in progressive ruptures of high-pressure pipelines and the platform's collapse, with 167 fatalities.^[63] The Cullen Inquiry highlighted how poor permit-to-work systems and compartmentalization flaws amplified the confined blast effects, prompting global offshore safety reforms.^[64]

Measurement Techniques and Standards

Field instrumentation for quantifying overpressure in blast scenarios relies on high-speed pressure gauges capable of capturing transient pulses with sub-microsecond rise times and frequencies exceeding 500 kHz. Kulite transducers, such as those in the HKS series, are widely used in military and commercial applications due to their high linear dynamic range, burst pressure ratings up to 100,000 psi, and negligible phase-shift errors, enabling accurate measurement of static overpressure, reflected overpressure, dynamic pressure, and total pressure in extreme close-in blast environments.^[65]^[66] To map spatial variations in blast fields, sensor arrays employing quartz or MEMS-based transducers are deployed, often flush-mounted on ground plates or arranged in radial configurations to capture peak overpressure and impulse distributions. For instance, arrays of Hopkinson pressure bars have been utilized to reconstruct blast load maps on structures, providing two-dimensional pressure profiles with resonant frequencies up to 1 MHz for precise shock wave analysis. PCB Piezotronics blast transducers, with ICP® circuitry delivering 5V outputs, further support these arrays by isolating thermal and strain effects through materials like Teflon®, ensuring data fidelity in high-shock conditions.^[67]^[68] Simulation software facilitates predictive modeling of overpressure propagation through computational fluid dynamics (CFD). ANSYS AUTODYN employs explicit solvers to simulate nonlinear dynamic events like explosions, accurately replicating air blast waves and material responses under high strain rates. Similarly, LS-DYNA's multi-material arbitrary Lagrangian-Eulerian (MMALE) formulation models blast wave clearing and urban propagation, validated against experimental data for overpressure peaks and impulses in confined geometries.^[69]^[70] Testing standards ensure consistent measurement protocols across applications. For flow-induced overpressures, ISO 5167-1 specifies methods using differential pressure devices like orifice plates and Venturi tubes in circular conduits, defining requirements for subsonic, single-phase fluid flow calibration with uncertainties below 1%. In military contexts, MIL-STD-1474E establishes limits for impulsive noise exposure, including blast overpressure, using the Auditory Hazard Assessment Algorithm for Humans (AHAAH) to predict peak levels and impulses safe for human auditory health, with thresholds such as 140 dB peak for unprotected ears. For explosive muzzle blasts, military protocols require transducers with resonant frequencies ≥75 kHz, nonlinearity ≤3%, and sampling rates ≥160 kHz, as outlined in standardization guidelines.^[71]^[72]^[73]^[74] Data validation involves calibrating instruments and models against empirical results from controlled tests and historical incidents to confirm accuracy within 5-10% for peak overpressures. High-impact simulations in AUTODYN and LS-DYNA are routinely benchmarked using datasets from arena tests and events like the 1983 Beirut barracks bombing, where equivalent TNT yields informed overpressure reconstructions of high levels at close range, enhancing predictive reliability for safety assessments.^[69]^[70]^[75]

References

[1]
Overpressure Levels of Concern | response.restoration.noaa.gov
Overpressure, also called a blast wave, refers to the sudden onset of a pressure wave after an explosion. This pressure wave is caused by the energy released in ...Missing: physics engineering
[2]
[PDF] Explosive blast 4 | FEMA
Explosive detonations create an incident blast wave, characterized by an almost instantaneous rise from atmospheric pressure to a peak overpressure. As the ...
[3]
Blast Overpressure - an overview | ScienceDirect Topics
Blast overpressure refers to the pressure generated by an explosion, characterized by maximum reflected pressure and decay over time and space, ...Missing: physics | Show results with:physics
[4]
Pore Pressure - an overview | ScienceDirect Topics
The magnitude of the pore pressure above the hydrostatic pressure is referred to as overpressure (POP), or excess pressure, and is defined as: (9) P OP = P ...
[5]
Pore pressure from geophysical well logs - SEG Library
Formation fluid pressure in excess of hydrostatic (overpressure, geopressure, abnormal pore pressure) has been recognized to cause severe drilling problems ...
[6]
11.6: Gauge Pressure, Absolute Pressure, and Pressure Measurement
Feb 20, 2022 · Gauge pressure is the pressure relative to atmospheric pressure. Absolute pressure is the sum of gauge pressure and atmospheric pressure.
[7]
Overpressure - Atomic Archive
Blast effects are usually measured by the amount of overpressure, the pressure in excess of the normal atmospheric value, in pounds per square inch (psi).
[8]
OVERPRESSURE Definition & Meaning - Dictionary.com
noun. pressure in excess of normal atmospheric pressure, as that caused by an explosion's shock wave or created in an accelerating airplane.Missing: engineering | Show results with:engineering
[9]
Overpressure - (Intro to Chemical Engineering) - Fiveable
Overpressure refers to the pressure in a system that exceeds the normal or atmospheric pressure, often caused by rapid changes in volume or energy input.
[10]
[PDF] Airblast Measurements and Equivalency for Spherical ... - DTIC
Characterization of blast waves from high explosive detonations in free air by experimental methods has a long history dating back to World War II, as reported ...
[11]
Blast Injuries: Preparing for the Inevitable - EB Medicine
Apr 1, 2006 · Mechanism of Primary Blast Injury. In World War II, blast overpressures were thought to gain access to internal organs through natural ...
[12]
Gauge Pressure, Absolute Pressure, and Pressure Measurement
Section Summary · Gauge pressure is the pressure relative to atmospheric pressure. · Absolute pressure is the sum of gauge pressure and atmospheric pressure.
[13]
Pressure Types and What They Mean
Sep 7, 2021 · With relative pressure, which is also known as overpressure, the process pressure to be determined is measured with reference to atmospheric ...
[14]
Pressure units and pressure unit conversion - Beamex blog
Feb 8, 2017 · Pascal (Pa) is the standard unit of pressure used to measure the amount of force exerted per unit area. It is named after Blaise Pascal, a ...
[15]
Pressure Converter
Complete list of pressure units for conversion · pascal [Pa] · 1 kilopascal [kPa] = 1000 pascal [Pa] · 1 bar = 100000 pascal [Pa] · 1 psi [psi] = 6894.7572931783 ...Convert bar to psi · Convert psi to bar · Convert kpa to psi · Convert psi to kpa
[16]
Pressure Sensors for Blast Testing | PCB Piezotronics
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing.
[17]
https://www.tek.com/en/blog/pressure-calibration
[18]
The Blast Gauge® System
The Blast Gauge System is a 3-sensor set worn on the head, shoulder, and chest. Unit medics and leadership are alerted wirelessly or via button push on gauge.
[19]
Pressure Calibration: Ensuring Accuracy, Safety, and Compliance
Sep 18, 2025 · Key Standards and Traceability (ISO 17025 & SI) This guarantees that the measurement is tied to an authoritative source. ISO/IEC 17025 ...
[20]
ASTM E74 Calibration Procedure Simplified
Feb 21, 2016 · The ASTM E74 calibration involves stabilization, warm-up, selecting test points, applying forces in multiple runs, and rotating the UUT. If ...
[21]
[PDF] Chapter THE PHYSICS AND MECHANISMS OF PRIMARY BLAST ...
The pressure-time history of the ideal blast wave is characteristic of many blast waves, especially those far from the explosion. However, if the chemical ...
[22]
The Science of Blast - Blast Injury Research Coordinating Office
Sep 12, 2024 · This overpressure wave propagates outward from the explosion in a radial fashion at supersonic speed, creating a wake of negative pressure (" ...
[23]
[PDF] Module 1 - Explosives
“High explosives” detonate, whereas “low explosives” deflagrate or burn. A high-explosives detonation provides both shock, which fractures (or breaks) the rock, ...Missing: overpressure nuclear
[24]
Nuclear Detonation: Weapons, Improvised Nuclear Devices
Bombs dropped on Hiroshima and Nagasaki, Japan at the end of World War II are examples of nuclear explosions. The explosive energy from a nuclear detonation is ...
[25]
Chapter III—Air Blast Phenomena in Air and Surface Bursts
3.39 The presence of large amounts of moisture in the atmosphere may affect the properties of a blast wave in the low overpressure region. But the ...
[26]
Scaled Distance - an overview | ScienceDirect Topics
2 Blast scaling. It is convenient to scale airblast parameters according to the dimensional, 'cube-root' scaling law. [1.13] ...
[27]
[PDF] Mechanisms of Confined Explosions and The Effects of Afterburn
This occurs through the temperature and pressure increase in a sealed environment having limited ways to escape to the surrounding environment and the ways it ...
[28]
[PDF] Modelling Confined Hydrocarbon Gas Explosions Part I - IOSR Journal
Jan 18, 2018 · This mechanism of flame acceleration due to repeated obstacles may result in a very high overpressures. (over 1 bar) within relatively short ...
[29]
Explosion properties - Gexcon's Knowledge Base
The rapid release of energy per unit of volume generates overpressure or shock waves, contributing to the destructive force of the explosion. Chemical ...<|control11|><|separator|>
[30]
A Boiler: The Explosive Potential of a Bomb
A common cause of explosion is the runaway firing condition that takes place when the boiler's burner does not shut off. In this case, when the hot-water heater ...
[31]
Exploring the Mysteries of Boiler Explosions : Uncovering Causes ...
Feb 18, 2025 · A malfunctioning pressure relief valve, failure to release steam properly, or improper operation can result in a dangerous buildup of pressure.
[32]
[PDF] Numerical Simulation and Analysis of Wood Dust Explosions in ...
In a closed vessel with no venting device, dust explosion pressures can reach 7–10 bar (700–1000 kPa), placing silos at risk of severe damage or even complete ...
[33]
Understanding and Preventing Dust Explosions - Causes Risks and ...
A dust explosion occurs when fine particles in the air ignite, causing rapid gas expansion and pressure waves. It requires fuel, oxygen, confinement, ...
[34]
Research on Natural Gas Leakage and Explosion Mechanisms in a ...
In this paper, a natural gas explosion test was carried out in an ordinary container house, and a numerical simulation was carried out according to the test ...
[35]
Study on Gasoline–Air Mixture Explosion Overpressure ... - MDPI
Oct 4, 2023 · The explosion overpressure and pressurization speed also increase first and then decrease with the gasoline–air mixture concentration increasing ...
[36]
Gasoline Vapor Explosion Modes in Confined Space under Weak ...
It also studies the overpressure variation of gasoline vapor explosion, the mechanism of flame shapes with time, and the coupling relationship between them ...
[37]
Research progress on multi-overpressure peak structures of vented ...
The peak structures in pressure curves are primarily generated by the pressure balancing process that occurs during vented gas explosions in confined spaces.
[38]
Explosion Venting and Vent Design Solutions | Fike
Explosion vent panels relieve a deflagration's pressure and flames from the vessel in order to keep its total pressure below its design pressure.
[39]
Under pressure: the benefits of explosion venting panels - HazardEx
Sep 14, 2021 · Explosion and pressure-relief venting is an effective standalone measure for relieving overpressure and mitigating the severity of deflagration.
[40]
[PDF] Glass Breakage – Failure Mode and Stress Estimation
Glass, like many brittle materials, breaks or fails when tension stresses approach or exceed the materials ultimate strength. There are two primary modes of ...
[41]
[PDF] Blast and Progressive Collapse
Blast loads are most often thought of as emanating from exothermic reactions resulting in “detonations”, however, shock waves in air can result from pressure ...
[42]
[PDF] Blast Loading and Blast Effects on Structures – An Overview
A bomb explosion within or immediately nearby a building can cause catastro- phic damage on the building's external and internal structural frames, collapsing ...
[43]
Halifax explosion of 1917 | Significance & Facts - Britannica
Oct 7, 2025 · Nearly 2,000 people died and some 9,000 were injured in the disaster, which flattened more than 1 square mile (2.5 square km) of the city of ...
[44]
[PDF] SIMPLIFIED KINGERY AIRBLAST CALCULATIONS - DTIC
Aug 16, 1994 · 7. Kingery, C. N. and Pannill, B. F., Peak Overpressure vs. Scaled Distance For TNT. Surface Bursts (Hemispherical Charges), BRL Memorandum ...
[45]
[PDF] Analysis of blast parameters in the near-field for spherical free-air ...
This means that the proposed blast parameters at scaled distance values Z<0.4m/kg1/3 should be treated with caution as they might not be conservative. Moreover, ...
[46]
[PDF] Air Blast Calculations - DTIC
Jul 18, 2013 · A Friedlander waveform is often used to describe the blast overpressure once the blast wave has fully developed (i.e., at some distance away ...<|control11|><|separator|>
[47]
Blast Wave - an overview | ScienceDirect Topics
The simplest form of a blast wave is described as the Friedlander waveform (Friedlander, 1946). ... The following equation describes the pressure as a function of ...
[48]
[PDF] An Empirical Non-TNT Approach to Launch Vehicle Explosion ...
The use of a TNT equivalent blast wave beyond this range may not always be a very good representation of the wave from a liquid propellant explosion, but at the ...
[49]
[PDF] Chemical Blast Standard (1 kg) - OSTI.GOV
Feb 21, 2023 · Applying scaling laws of blast waves. (Needham, et al., 1975), Needham and Crepeau published an overpressure model for nuclear explosions based ...
[50]
[PDF] SIMPLIFIED EULERIAN SIMULATION OF BLAST WAVE ... - WIT Press
Figure 3: Incident peak-overpressure of Eulerian model and Kingery–Bulmash data. Figure 4: Time of arrival of Eulerian model compared to Kingery–Bulmash data.
[51]
[PDF] PRESSURE RISE IN CONFINED GAS EXPLOSIONS
Dec 30, 2005 · The main reason to model pressure rise in confined explosions has been the need to calculate the flame speed of a mixture from measured pressure ...Missing: enclosed | Show results with:enclosed
[52]
VDI 2263 - Dust fires and dust explosions - Hazards - assessment
This standard is valid for the evaluation of hazards and measures to prevent dust fires and dust explosions as well as their dangerous impacts.Missing: deflagration index K_g
[53]
https://standards.iteh.ai/catalog/standards/cen/73e55b45-f118-4aac-9678-c02d8374c1bf/en-14491-2012
[54]
[PDF] New Revised European Norm on Dust Explosion Venting Protection ...
EN 14491 specifies design requirements for dust explosion venting. The revised standard adds requirements for pneumatic conveying, free fall filling, vent duct ...Missing: models nomograms relief
[55]
Dust explosions in vented silos: Simulations and comparisons with ...
In a closed vessel with no venting device, dust explosion pressures can reach 7–10 bar (700–1000 kPa), placing silos at risk of severe damage or even complete ...
[56]
DEVCOM Armaments Center engineers seek to increase Soldier ...
Jul 17, 2025 · Over the past years, blast overpressure from howitzers has been reduced through optimization of the muzzle brake design through numerical ...
[57]
[PDF] DDESB Blast Effects Computer – Open (BEC-O) Version 1 User's ...
Jun 11, 2018 · The Department of Defense Explosives Safety Board (DDESB) has had an active role in producing various explosion effects computation aids for ...Missing: military radius<|separator|>
[58]
[PDF] APPROVED PROTECTIVE CONSTRUCTION - DOD DENIX
Jul 26, 2020 · clearly shows that the exposed security alert facility has been hardened against blast overpressure ... U.S. Army Engineering and Support Center, ...
[59]
https://www.nfpa.org/codes-and-standards/all-codes-and-standards/list-of-codes-and-standards/detail?code=68
[60]
Directive - 2014/34 - EN - ATEX directive - EUR-Lex
Summary of each segment:
[61]
[PDF] Fault Tree Analysis for over pressurization in high pressure section ...
Fault tree analysis is a technique used to find all the reasons for any undesired top event. In this paper, over pressurization in HP section is taken as a top ...
[62]
[PDF] NUREG-0492, "Fault Tree Handbook".
Fault Tree Analysis addresses itself to the identification and assessment of just such catastrophic occurrences and complete failures. 3. The Undesired ...
[63]
Remembering Piper Alpha: The catastrophic 1988 offshore disaster
When the initial gas exploded, the firewalls that were designed to withstand burning oil failed under the overpressure. As there was no design for blast ...The Event · Emergency Response And... · Human And Organisational...Missing: confined | Show results with:confined<|control11|><|separator|>
[64]
The Public Inquiry into the Piper Alpha Disaster - HSE
Jul 8, 2025 · The Public Inquiry into the Piper Alpha Disaster.Missing: overpressure | Show results with:overpressure
[65]
Product Advisor | Kulite | The Leader in Pressure Transducer ...
Designed for high pressure, high shock environments, this transducer is widely used in both military and commercial blast measurement applications.
[66]
[PDF] Section 7 - Measurement of Transient Pressure Pulses - Kulite
To determine the effects from explosive detonations, pressure measurements are taken of the airblasts. Four important pressure measurements are associated with ...
[67]
Reconstruction of surface pressures on flat plates impacted by blast ...
Here, the authors used arrays of Hopkinson pressure bars that allowed them to map the resulting blast load distributions. ... Pressure field maps for half-blocked ...
[68]
[PDF] Measuring Static Overpressures in Air Blast Environments
Sep 26, 2006 · This assessment requires measurement of: (1) the peak static overpressure and (2) the total impulse per unit area of the blast wave. The total ...
[69]
Ansys Autodyn - Rand SIM
Ansys Autodyn simulates the response of materials to short duration severe loadings from impact, high pressure or explosions.
[70]
[PDF] Validation of LS-DYNA MMALE with Blast Experiments - DYNAmore
This paper presents a validation study of the LS-DYNA MMALE approach with existing experimental studies of blast wave clearing and blast in an urban ...
[71]
ISO 5167-3:2020 - Measurement of fluid flow by means of pressure ...
This standard specifies the geometry and use of nozzles and Venturi nozzles for measuring fluid flow in full conduits, including three standard nozzle types.
[72]
ISO 5167-1:2003 - Measurement of fluid flow by means of pressure ...
ISO 5167-1:2003 defines principles for measuring fluid flow using pressure devices, specifies requirements, and applies to subsonic, single-phase flow.
[73]
[PDF] DEPARTMENT OF DEFENSE DESIGN CRITERIA STANDARD ...
Apr 15, 2015 · This standard specifies the maximum permissible noise levels produced by military systems and the test requirements for measuring these ...
[74]
[PDF] Standardization of Muzzle Blast Overpressure Measurements - DTIC
1. All transducers will be calibrated in a manner consistant with the transducer's time constant, i.e., sinusodual pressure generator, pulse calibrator, dead ...
[75]
5 Harrowing Facts About the 1983 Beirut Barracks Bombing
Sep 16, 2022 · 5 Harrowing Facts About the 1983 Beirut Barracks Bombing · 1. The bomb was the largest non-nuclear explosion since World War II. · 2. It was the ...<|control11|><|separator|>