Fact-checked by Grok 2 weeks ago

Flow measurement

Flow measurement is the quantification of the rate at which a fluid—such as a liquid, gas, or vapor—passes through a conduit, pipe, or channel, typically expressed as either volumetric flow rate (volume per unit time, e.g., m³/s) or mass flow rate (mass per unit time, e.g., kg/s), based on principles like the continuity equation for incompressible or compressible fluids.^[1] This process relies on devices known as flowmeters, which detect fluid movement through various physical phenomena, including pressure differentials, velocity changes, displacement, or direct mass effects, with accuracy influenced by factors like fluid properties (density, viscosity), temperature, pressure, and flow regime (e.g., Reynolds number).^[1]^[2] Flow measurement is essential across industries for process control, resource allocation, custody transfer (e.g., billing in oil and gas), environmental monitoring, and regulatory compliance, such as assessing water resources or pollution levels, where precise quantification ensures operational efficiency and prevents errors that could lead to significant economic or safety issues.^[3]^[1] In liquid systems, it supports applications like irrigation and chemical dosing, while for gases, it is critical in HVAC, combustion processes, and natural gas distribution; calibration against primary standards, such as gravimetric or pressure-volume-temperature-time (PVTt) methods, achieves uncertainties as low as 0.1–0.3% for high-precision needs.^[2] Key methods encompass several categories, each suited to specific conditions: For gases, additional considerations include compressibility and species effects, often calibrated using critical flow venturis (discharge uncertainty ~0.09–0.3%) or laminar elements for low flows (<1 L/min).^[2] Overall, selection depends on fluid type, pipe size, flow range, and installation constraints, with standards from organizations like NIST ensuring traceability and reliability.^[1]

Basic Concepts

Units and Principles

Flow measurement refers to the process of quantifying the rate at which a fluid—such as a liquid or gas—moves through a conduit or system, enabling precise monitoring and control of fluid dynamics in various applications.^[4] A fundamental distinction in flow measurement lies between volumetric flow rate and mass flow rate. Volumetric flow rate, denoted as Q or \dot{V}, represents the volume of fluid passing through a cross-section per unit time, typically expressed in units like cubic meters per second (m³/s) or liters per minute (L/min); it is calculated as Q = A v, where A is the cross-sectional area and v is the average fluid velocity.^[5] In contrast, mass flow rate, denoted as \dot{m}, measures the mass of fluid per unit time, in units such as kilograms per second (kg/s), and is related to volumetric flow by the equation \dot{m} = \rho Q, where \rho is the fluid density; mass flow is independent of temperature and pressure variations that affect volumetric measurements, making it more reliable for compressible fluids.^[6] The continuity equation underpins these measurements by enforcing conservation of mass in fluid flow. For steady, incompressible flow in a pipe, it simplifies to A_1 v_1 = A_2 v_2, indicating that the product of cross-sectional area and velocity remains constant along the flow path. This equation derives from the principle that, under steady-state conditions, the mass flow rate entering a control volume equals the mass flow rate exiting it, with no accumulation inside; mathematically, integrating the differential form \frac{\partial \rho}{\partial t} + \nabla \cdot (\rho \mathbf{v}) = 0 over a volume and applying the divergence theorem yields net mass flux zero for constant density.^[7]^[8] Flow measurement holds critical importance across industries, including water supply for distribution and billing, oil and gas for production allocation and custody transfer, and chemical processing for reaction control and safety. Its development traces to 19th-century innovations, such as the Venturi tube metering device, adapted by Clemens Herschel in 1888 based on Giovanni Battista Venturi's earlier 1797 observations of pressure drops in converging flows.^[9]^[10] A key dimensionless parameter in flow measurement is the Reynolds number, Re = \frac{\rho v d}{\mu}, where v is velocity, d is a characteristic length like pipe diameter, and \mu is dynamic viscosity; it represents the ratio of inertial to viscous forces. Flow regimes are classified by Re: laminar for Re < 2300, where smooth, layered motion predominates, and turbulent for Re > 4000, characterized by chaotic mixing; transitional flow occurs between 2300 and 4000. The Reynolds number significantly influences meter accuracy, as many devices, such as differential pressure meters, require turbulent conditions (Re > 10,000) for stable, predictable performance and minimal error.^[11]^[12]^[13]

Flow Types and Regimes

Flow measurement requires classification of fluids based on their physical properties and behavior, which directly influences the accuracy and methodology of quantification. Liquids are generally incompressible with high density, allowing for straightforward volumetric flow assumptions under standard conditions. Gases, in contrast, are compressible and exhibit low density, necessitating corrections for density variations during measurement. Slurries and multiphase flows incorporate solids or particles suspended in liquids or gases, complicating measurement due to heterogeneous distributions and potential erosion effects.^[14] Steam represents a two-phase flow, combining liquid and vapor phases, where phase transitions demand specialized handling to account for latent heat and void fractions.^[15] Flow regimes further delineate measurement challenges, primarily through laminar and turbulent characteristics. Laminar flow features smooth, layered motion with a parabolic velocity profile across the pipe cross-section, occurring at low Reynolds numbers typically below 2300, and is prevalent in viscous fluids or small-diameter conduits.^[11] Turbulent flow, dominant in most industrial pipelines with Reynolds numbers exceeding 4000, exhibits chaotic eddies and a relatively flat velocity profile, enhancing mixing but introducing fluctuations that can affect measurement stability.^[11] The Reynolds number serves as a key indicator for distinguishing these regimes, balancing inertial and viscous forces.^[16] Temperature and pressure significantly impact gas flow measurements due to compressibility effects. For gases, the ideal gas law, PV = nRT, describes how volume expands with rising temperature or falling pressure at constant moles, requiring expansion factor corrections to maintain volumetric accuracy.^[17] In liquids, cavitation arises when local pressure drops below the fluid's vapor pressure, forming vapor bubbles that collapse and potentially damage equipment or distort flow profiles.^[18] This phenomenon limits maximum flow rates in high-velocity scenarios, particularly in warmer liquids with higher vapor pressures.^[19] Flows in open channels differ from those in closed conduits, affecting measurement approaches. Open-channel flows occur with a free surface exposed to atmospheric pressure, as in rivers or sewers, requiring sensing of both depth and velocity since cross-sectional area varies with level; this introduces complexities like surface waves but allows non-intrusive gravity-driven assessments.^[20] Closed-conduit flows, fully pressurized within pipes, offer consistent geometry for precise volumetric calculations but demand sealed systems to prevent leaks or air entrainment.^[20] Measurement in open channels is generally more challenging due to variable free-surface positioning compared to the fixed boundaries in closed systems.^[21] Early conceptual distinctions in flow types trace to Daniel Bernoulli's 1738 publication Hydrodynamica, where Bernoulli's principle—relating pressure, velocity, and elevation in real fluid flows—laid foundational insights into compressible and incompressible behaviors beyond ideal assumptions. This work marked the initial application of energy conservation to practical flow measurement, influencing subsequent regime classifications.^[22]

Mechanical Flowmeters

Positive Displacement Meters

Positive displacement meters operate on the principle of repeatedly trapping a fixed volume of fluid within one or more chambers and then displacing that volume through mechanical action, with the total flow determined by counting the number of displacement cycles via a mechanical or electronic linkage.^[23] This method is particularly suited to measuring viscous liquids at low flow speeds, as the meter's accuracy relies on the complete filling and emptying of chambers rather than fluid velocity.^[23] Several subtypes of positive displacement meters exist, each employing distinct mechanical configurations to achieve volume displacement. Rotary piston meters use a reciprocating or oscillating piston within a cylindrical chamber to draw in and expel fluid, offering high accuracy of approximately ±0.5% for custody transfer applications.^[23] Oval gear meters feature two intermeshing, oval-shaped lobes that rotate in opposite directions, trapping fluid between them without metal-to-metal contact to minimize wear and provide smooth operation for lubricating fluids.^[23] Helical gear meters, also known as screw-type meters, utilize multiple screw-like rotors that mesh to propel fluid continuously along the meter axis, enabling handling of higher viscosities and providing steady flow measurement.^[23] Nutating disk meters employ a disk that wobbles or nutates in a spherical chamber, dividing the space into alternating fill and discharge volumes, and are commonly used for precise billing in water and fuel applications.^[23] The volumetric flow rate Q in positive displacement meters is calculated using the equation:

Q = \frac{V_{\text{chamber}} \times N}{t}

where V_{\text{chamber}} is the known volume displaced per cycle, N is the number of cycles, and t is the time interval.^[24] This direct volumetric approach ensures reliable totalization of flow volume over time.^[24] These meters offer advantages such as exceptional accuracy for batching and dispensing operations, often achieving ±0.1% to ±0.5% depending on the subtype and conditions, and they require no straight pipe runs upstream or downstream for installation.^[23] However, they are susceptible to wear from solid particulates in the fluid, necessitating clean service conditions and filtration, and are generally limited to non-abrasive, viscous liquids due to potential slippage or mechanical degradation at high speeds.^[23] Positive displacement meters find primary applications in fuel dispensing at retail and aviation sites, chemical dosing in industrial processes, and custody transfer of petroleum products where precise volumetric measurement is critical.^[23] Historically, their adoption accelerated in the early 20th-century oil industry, with designs like the Smith Meter PD meter first produced in 1940 to meet the demands of accurate hydrocarbon measurement in pipelines and terminals.^[25] Unlike velocity-based meters suited for higher flow rates, positive displacement types excel in low-speed, high-precision scenarios.^[23] Standards such as API MPMS Chapter 5.2 provide guidelines for their use in liquid hydrocarbon metering, emphasizing calibration and performance in industrial settings.^[24]

Velocity Meters

Velocity meters are mechanical flowmeters that measure fluid flow by detecting the velocity of the fluid through the interaction with rotating or moving elements, such as blades or propellers. The core principle involves the fluid impinging on these elements, causing rotation whose speed is directly proportional to the fluid velocity; the volumetric flow rate is then derived from this velocity multiplied by the pipe's cross-sectional area, with calibration required to adjust for influences like fluid density and viscosity.^[26] These meters are particularly suited for moderate-to-high flow rates in liquids, contrasting with positive displacement meters that capture discrete volumes at lower velocities.^[10] Key subtypes include turbine meters, which feature a multi-blade rotor aligned with the flow; the flow rate Q is calculated as Q = kN, where k is a calibration factor and N is the rotor frequency, achieving typical accuracies of ±1% for clean, low-viscosity liquids.^[27] Single-jet meters direct a single water stream through a nozzle onto a radial turbine in a chamber, offering simplicity and suitability for small-diameter residential applications with moderate accuracy at low flows.^[28] Multiple-jet meters improve on this by using several ports to evenly distribute the flow around the turbine, enhancing accuracy (especially at low rates) and durability for larger water users up to 3-inch diameters.^[28] Woltman meters employ a horizontal-axis turbine for large-diameter pipes, where rotation speed balances driving and drag torques proportional to flow, with accuracies impacted by upstream disturbances like valves, requiring at least 3 pipe diameters of straight inlet for optimal performance.^[29] Pelton wheel meters, a variant of impulse turbines, use cupped blades to capture high-velocity jets, providing 1.5–3% accuracy for low-flow, high-pressure water-like liquids in compact designs.^[30] Paddle wheel meters utilize simple perpendicular vanes that rotate with the flow, offering cost-effective measurement (2.5–5% accuracy) for opaque or viscous fluids where visibility is not required.^[31] Current meters, often propeller-based, measure velocity in open channels or rivers by propeller rotation calibrated to water speed, suitable for environmental monitoring with portable, lightweight construction.^[32] Accuracy in velocity meters is influenced by factors such as bearing friction, which reduces sensitivity at low flows; cavitation, occurring at high velocities where pressure drops cause vapor bubble formation and erratic readings; and a minimum Reynolds number of approximately 10^4 to ensure turbulent flow for reliable operation.^[33] These meters generally require 10–20 pipe diameters of straight upstream piping to develop a uniform velocity profile and minimize errors from turbulence.^[29] Advantages include robustness in handling dirty or contaminated fluids without clogging, wide turndown ratios, and relatively low cost compared to more advanced technologies.^[26] Disadvantages encompass sensitivity to installation conditions, potential wear from particulates, and inability to measure very low flows accurately due to friction thresholds.^[31] Applications span irrigation systems, wastewater treatment, and large-scale water distribution, where their mechanical reliability supports continuous monitoring in rugged environments.^[34] Historically, these meters trace back to the 1790s, when Reinhard Woltman developed the first turbine-like design using a multi-bladed fan for water flow measurement, evolving from early water wheels into modern inferential devices.^[10]

Differential Pressure Flowmeters

Orifice and Venturi Devices

Orifice and Venturi devices are differential pressure flowmeters that measure fluid flow by creating a constriction in the pipe, which accelerates the fluid and produces a measurable pressure drop based on Bernoulli's principle. For an incompressible fluid in horizontal flow, Bernoulli's equation simplifies to P_1 + \frac{1}{2} \rho v_1^2 = P_2 + \frac{1}{2} \rho v_2^2, where P is pressure, \rho is fluid density, and v is velocity at upstream (1) and downstream (2) points. This velocity increase through the constriction results in a pressure differential \Delta P = P_1 - P_2, which is related to the volumetric flow rate Q by the equation:

Q = C_d A_2 \sqrt{\frac{2 \Delta P}{\rho (1 - \beta^4)}}

For compressible fluids such as gases and steam, the equation is modified by an expansion factor Y to correct for density changes: Q = Y C_d A_2 \sqrt{\frac{2 \Delta P}{\rho (1 - \beta^4)}}, where Y (typically 0.95–1.00) depends on \beta, the relative pressure drop \Delta P / P_1, and the isentropic exponent, as per ISO 5167.^[35] Here, C_d is the discharge coefficient (typically 0.6–0.8, accounting for flow contraction and friction), A_2 is the cross-sectional area at the constriction throat, and \beta is the diameter ratio (d/D, where d is throat diameter and D is pipe diameter). This formula applies to both orifice plates and Venturi meters, with device-specific values for C_d and \beta determined by empirical calibration or standards.^[36]^[35] The orifice plate is the simplest and most economical constriction device, consisting of a thin, flat plate (typically 3–6 mm thick) inserted between pipe flanges with a precisely machined circular hole, either concentric (centered) for symmetric flows or eccentric (offset) for fluids with suspended solids to prevent accumulation. It generates a significant pressure drop, up to 90% of the inlet pressure, making it suitable for high-flow applications but resulting in substantial permanent energy loss. International standards such as ISO 5167-2 specify design parameters, including \beta ratios from 0.2 to 0.75, plate thickness relative to D, and tap configurations to ensure accuracy within ±2–4% of full scale under turbulent conditions (Reynolds number > 4,000). Orifice plates are widely used due to their low cost (often under $100 for small sizes) and ease of replacement, though they require periodic inspection for edge wear.^[35] In contrast, the Venturi meter features a smooth, converging-diverging nozzle integrated into the pipe, with a throat section followed by a gradual expansion to recover velocity head and minimize permanent pressure loss, typically 10–20% of the measured \Delta P. This design yields higher accuracy (±0.5–1%) and better long-term stability, particularly for clean liquids and gases, as the smooth contours reduce turbulence and erosion compared to the sharp-edged orifice. Venturi meters are governed by ISO 5167-4, which outlines geometries for classical (long-form) and improved (short-form) variants, with \beta up to 0.75 and discharge coefficients around 0.98 for well-designed units. They are preferred in applications where energy conservation is critical, such as water supply systems or low-pressure gas lines, though their higher fabrication cost (often 5–10 times that of an orifice) limits use to larger pipes (>50 mm diameter).^[37] Installation of both devices requires careful attention to piping to ensure flow profile uniformity and measurement reliability. Pressure taps are typically located upstream (before the constriction) and downstream (in the throat for orifice, or at the vena contracta for Venturi), with common types including flange taps (1 inch from the plate faces) or D and D/2 taps (one pipe diameter upstream and half downstream from the plate). A straight pipe run of at least 10 pipe diameters (D) upstream and 5D downstream is recommended to avoid distortions from bends, valves, or expansions, as per ISO 5167 guidelines; reduced runs are possible with flow conditioners but may increase uncertainty. These devices are versatile for measuring flows of liquids, gases, and steam across a wide range of pressures and temperatures, offering turndown ratios of 4:1 to 10:1. However, orifice plates suffer from higher unrecovered pressure losses (50–80% of \Delta P), leading to greater energy consumption in pumping systems, while Venturi meters mitigate this at the expense of size and cost.^[38]^[39] Historically, the Venturi effect was first described by Italian physicist Giovanni Battista Venturi in 1797 during experiments on fluid jets and pipe contractions, laying the foundation for converging-diverging flow devices. Orifice plates emerged in the mid-19th century for flow control and measurement in steam engines, evolving from simple restrictions in boiler feed lines to standardized meters by the early 20th century.^[9]^[40]

Pitot and Averaging Tubes

The Pitot tube, a fundamental differential pressure flow measurement device, was invented by French engineer Henri Pitot in 1732 to quantify water velocities in rivers and channels.^[41] This simple instrument captures the difference between stagnation pressure (total pressure at a point where flow is brought to rest) and static pressure, enabling velocity determination without full pipe constriction.^[42] Over time, its design evolved for aviation and industrial uses, with refinements like the S-type configuration enhancing suitability for low-speed gaseous flows.^[43] The operating principle relies on Bernoulli's equation, where the velocity head, or pressure difference ΔP, represents the kinetic energy of the fluid:

\Delta P = \frac{1}{2} \rho v^2

Here, ρ is the fluid density and v is the local flow velocity; solving for v yields v = \sqrt{\frac{2 \Delta P}{\rho}}.^[42] The volumetric flow rate Q through a duct of cross-sectional area A is then Q = K A v = K A \sqrt{\frac{2 \Delta P}{\rho}}, where K is a geometry-specific discharge coefficient, often 0.98 to 1.00 for well-calibrated tubes, accounting for minor deviations from ideal flow.^[44] Standard Pitot tubes feature an impact tube aligned with the flow to sense total pressure and perpendicular static ports for ambient pressure, making them ideal for point measurements in clean gases or air streams within ducts.^[42] The S-type variant, with its offset arms and hemispherical tips, improves sensitivity at low velocities (below 10 m/s) and is standardized for applications like emission stack traversals.^[43] Averaging Pitot tubes extend this concept to provide mean velocity across the entire pipe cross-section, mitigating errors from non-uniform velocity profiles that plague single-point measurements.^[44] These devices incorporate multiple upstream impact ports and downstream static ports arranged along an annular or conical bluff body, which averages pressures to yield a representative ΔP for the bulk flow.^[44] Annular designs position ports around the pipe periphery, while cone variants enhance averaging in distorted profiles by promoting radial mixing; both reduce profile-induced uncertainties to ±2-5% accuracy under turbulent conditions (Reynolds numbers >10,000).^[44] The same flow equation applies, with K calibrated via testing to reflect the multi-port geometry, typically ranging from 0.90 to 0.99 depending on pipe size and flow regime.^[44] For compressible flows, such as high-speed gases or vapors, the basic incompressible formula requires correction using an expansion factor Y, which adjusts for density variations across the sensing plane: Y \approx 1 - (1 - \beta^2) \frac{\Delta P}{2 P_1 \gamma} (approximate form for small β, the diameter ratio), where P1 is upstream pressure and γ is the specific heat ratio; Y approaches 1 for liquids or low-Mach gases but drops below 0.99 for compressible cases.^[35] This factor ensures the computed velocity reflects isentropic expansion effects, as derived from compressible Bernoulli relations.^[35] Pitot and averaging tubes are deployed in diverse settings, including HVAC systems for verifying duct airflow rates to meet ventilation standards, aircraft for real-time airspeed computation via integrated pitot-static systems, and industrial stacks for volumetric flow assessment in emission compliance testing.^[45]^[42]^[46] Their low cost, minimal pressure loss (typically <1% of ΔP), and ease of insertion suit large ducts or pipes from 50 mm to over 2 m in diameter.^[44] Despite advantages, these devices have limitations: fouling from particulates or viscous fluids can obstruct ports, necessitating frequent cleaning or purging in dirty streams like wastewater vents or dusty process gases.^[47] They also demand uniform upstream flow, with at least 10-20 pipe diameters of straight run to avoid swirl or asymmetry errors exceeding 5%; non-uniform profiles in elbows or expansions degrade averaging efficacy.^[48] At very low velocities (<2 m/s), the small ΔP becomes hard to measure accurately without sensitive transducers.^[42]

Variable Area and Vortex Flowmeters

Variable Area Meters

Variable area meters, also known as rotameters, operate on the principle of a float suspended in a tapered tube where the position of the float indicates the flow rate. The fluid enters the bottom of the vertical tube, exerting an upward drag force on the float that balances the float's effective weight (accounting for buoyancy), causing the float to rise and increase the annular area between the float and the tube wall. This balance ensures that the volumetric flow rate Q is approximately proportional to the annular area A_{\text{annulus}} times the square root of $2gh, where h is the effective head difference across the float, providing a direct visual indication of flow through the float's equilibrium height.^[49] These meters feature a precision-tapered tube made of glass for visual observation or metal for durability in harsh environments, with floats typically shaped as balls (e.g., ceramic, glass, or stainless steel) or plugs (e.g., conical or guided types) selected based on fluid properties. The scale along the tube is calibrated for specific fluids, densities, and viscosities to ensure accurate readings, and spring-loaded variants incorporate a counteracting spring to enable horizontal installation by compensating for gravity.^[50]^[51]^[52] Advantages of variable area meters include their simple mechanical design requiring no external power, ease of installation with minimal straight pipe runs, and a typical turndown ratio of 10:1 for versatile flow ranges. However, they are limited to visual or local indication without remote transmission capabilities and are sensitive to changes in fluid density and viscosity, which can alter the float's position and require recalibration. Accuracy is generally ±2-5% of full scale, though higher precision models achieve ±1-2%, and they necessitate vertical installation with upward flow to maintain gravitational balance, except for spring-loaded designs.^[53]^[50]^[54] Historically, variable area concepts trace back to 19th-century sight glasses and early patents, such as Edmund A. Chameroy's 1868 invention of a conical tube with a floating element for flow indication, which evolved into modern rotameters with the 1908 patent by Karl Küppers introducing a rotating float for improved stability and accuracy, leading to widespread commercialization in the 1930s. They are commonly applied in laboratory settings for purge gas monitoring, chemical feed systems, and process analyzers where low-flow, clean liquids or gases require simple, cost-effective visual confirmation.^[55]^[53]^[52]

Vortex Shedding Meters

Vortex shedding meters, commonly referred to as vortex flowmeters, measure fluid flow by detecting the periodic formation and shedding of vortices downstream of a stationary bluff body placed in the flow path. This phenomenon, known as the von Kármán vortex street, occurs when a fluid passes over the bluff body, generating alternating low-pressure vortices on either side at a frequency directly proportional to the flow velocity. The principle was first theoretically described by Theodore von Kármán in 1912 based on earlier observations of vortex formation.^[56] The shedding frequency f is related to the flow velocity v and the width d of the bluff body through the Strouhal number S, given by the equation:

f = \frac{S v}{d}

where S is approximately 0.2 for typical bluff body geometries over a wide range of Reynolds numbers. The volumetric flow rate Q is then derived as:

Q = \frac{f d}{S} \cdot \frac{\pi D^2}{4}

assuming a circular pipe cross-section of internal diameter D; this allows electronic processing of the frequency signal to compute flow rate without mechanical components.^[57]^[58] In design, the bluff body is often a non-streamlined element such as a triangular prism or T-shaped bar inserted perpendicular to the flow, spanning part or all of the pipe diameter to ensure stable vortex formation. Vortices are detected using piezoelectric sensors that capture pressure fluctuations or, in some models, ultrasonic transducers that measure velocity changes between shed vortices. These meters typically offer a turndown ratio of 10:1 and reliable operation at Reynolds numbers ranging from $10^4 to $10^7, beyond which the Strouhal number may vary.^[59]^[60] Key advantages of vortex shedding meters include the absence of moving parts, which enhances durability and reduces maintenance in harsh environments, and their versatility for measuring liquids, gases, and steam with minimal pressure drop. They excel in applications involving high temperatures or corrosive fluids due to robust construction. However, disadvantages encompass sensitivity to pipeline vibrations, which can mimic or disrupt vortex signals, and limitations at low Reynolds numbers where vortex shedding becomes irregular or ceases.^[61]^[62] Common applications span the petrochemical sector for monitoring hydrocarbon and chemical flows, HVAC systems for air and chilled water distribution, and power generation for superheated steam lines. Unlike variable area meters that rely on visual float balancing, vortex shedding meters process dynamic frequency signals electronically for precise, automated readout. Historically, while the underlying vortex street theory dates to the early 20th century, practical research for flow measurement advanced in the mid-20th century, leading to commercialization in the late 1960s and 1970s, with Yokogawa introducing the first model in 1969.^[63]^[64] These meters achieve typical accuracy of ±1% of reading across their range, with repeatability often better than 0.5%. Advanced multivariable versions integrate differential pressure and temperature sensors to directly output mass flow rates, compensating for density variations in gases and steam.^[60]^[63]

Mass and Thermal Flowmeters

Thermal Mass Flowmeters

Thermal mass flowmeters measure the mass flow rate of gases by exploiting the principle of convective heat transfer from a heated element to the flowing fluid. The core relationship is given by the heat transfer equation Q = \dot{m} C_p \Delta T, where Q is the heat transfer rate, \dot{m} is the mass flow rate, C_p is the specific heat capacity of the fluid, and \Delta T is the temperature difference between the heater and the fluid.^[65] This direct measurement of mass flow eliminates the need for density, pressure, or temperature compensation, making these devices particularly suitable for gas applications where volumetric flow variations due to process conditions are common.^[66] In operation, thermal mass flowmeters typically employ two resistance temperature detectors (RTDs): one serves as an active heater maintained at a constant temperature above the fluid, while the other acts as a downstream sensor to detect the temperature rise due to heat convection. The power required to sustain this temperature differential correlates with the mass flow rate through King's law, expressed as Nu = a + b Re^m Pr^n, where Nu is the Nusselt number representing dimensionless heat transfer, Re is the Reynolds number indicating flow regime, Pr is the Prandtl number for fluid properties, and a, b, m, and n are empirically determined constants specific to the sensor geometry and fluid.^[67] This law, originally derived for hot-wire anemometry, quantifies the balance between forced convection (flow-dependent) and natural conduction (flow-independent) heat loss from the sensor.^[68] Thermal mass flowmeters are categorized into several subtypes based on design and flow range. Immersible or capillary types are used for low-flow applications, where the entire gas stream passes through a small heated tube or sensor element for precise measurement. Insertion probes, suitable for larger ducts or pipes, extend into the flow path to sample velocity at a point, averaging across the cross-section for total flow estimation. Bypass configurations divert a representative fraction of the main flow through a capillary sensor, enabling measurement of higher overall flow rates while maintaining accuracy in the sensing element.^[69] These designs originated in the 1970s from adaptations of hot-wire anemometry techniques developed for aerodynamic research, with early commercial units focusing on clean gas flows in laboratory settings.^[68] Key advantages include direct mass flow output without additional corrections for gas density changes, high turndown ratios up to 100:1 for versatile range coverage, and suitability for low-pressure-drop installations in gas lines. However, they are limited to clean, dry gases, as contamination from particulates, moisture, or corrosive components can foul the sensors, altering calibration and reducing accuracy to beyond the typical ±1-2% of reading.^[70] Common applications encompass semiconductor manufacturing for process gas control, combustion air monitoring in boilers and furnaces to optimize efficiency, and flare gas measurement in oil and gas operations.^[71] In contrast to methods like Coriolis flowmeters, which handle liquids via inertial effects, thermal mass flowmeters excel in gaseous convective heat dispersion but require periodic recalibration in variable composition environments.^[72]

Coriolis Flowmeters

Coriolis flowmeters measure mass flow rate directly by detecting the Coriolis force acting on a fluid passing through vibrating tubes. The principle relies on the Coriolis acceleration, given by \mathbf{a}_c = 2 \boldsymbol{\omega} \times \mathbf{v}, where \boldsymbol{\omega} is the angular velocity of the tube vibration and \mathbf{v} is the fluid velocity. As the fluid flows through the oscillating tube, it experiences this force, causing a phase shift or time delay (\Delta t) between the vibrations at the tube's inlet and outlet, which is proportional to the mass flow rate (\dot{m}). The mass flow rate is calculated as Q_m = K \frac{\Delta t}{T_{vib}}, where K is a calibration factor and T_{vib} is the vibration period.^[73]^[74] These flowmeters typically feature U-shaped or S-shaped tubes driven into oscillation by an electromagnetic coil at their resonant frequency, with sensors (often electromagnetic pickoffs) detecting the phase difference. Straight-tube designs are also used to minimize pressure drop, particularly in applications requiring low resistance to flow, while maintaining the vibrating structure for measurement. The tubes are housed in a sensor body that isolates external vibrations, ensuring stable operation.^[73]^[70] Coriolis flowmeters offer high accuracy, typically ±0.1% of rate or better, and can simultaneously measure fluid density by analyzing shifts in the tube's resonant frequency, providing additional process insights without extra instrumentation. They are versatile, applicable to a wide range of fluids including liquids, gases, slurries, and multiphase mixtures, and are unaffected by changes in temperature, pressure, density, or viscosity. Common applications include custody transfer in oil and gas, chemical processing, and food and beverage production where precise mass measurement is critical.^[73]^[74]^[75] Despite their precision, Coriolis flowmeters are relatively expensive due to complex manufacturing and materials, and they require vibration isolation to prevent external disturbances from affecting measurements. They may also exhibit poor zero stability for very low flows, potentially impacting accuracy in such scenarios.^[73]^[75] The theoretical foundation dates to the 1950s, with early patents exploring Coriolis effects for flow measurement, but commercial viability emerged in the 1970s. Micro Motion introduced the first practical industrial Coriolis flowmeter in 1977 via a key patent, leading to widespread adoption in the 1980s with dual-tube designs that improved reliability and range.^[76]^[77]

Electromagnetic and Ultrasonic Flowmeters

Magnetic Flowmeters

Magnetic flowmeters, also known as electromagnetic flowmeters, operate on the principle of Faraday's law of electromagnetic induction to measure the volumetric flow rate of conductive liquids. A uniform magnetic field is generated perpendicular to the flow direction within a non-conductive pipe section, and as the conductive fluid moves through this field, a voltage is induced across electrodes positioned diametrically opposite each other. The induced voltage E is given by E = B l v, where B is the magnetic field strength, l is the distance between the electrodes (typically the pipe diameter), and v is the average fluid velocity. The volumetric flow rate Q can then be calculated as Q = \frac{E A}{B l}, with A representing the cross-sectional area of the pipe.^[78]^[79]^[80] The design of a magnetic flowmeter features a full-bore flow tube lined with insulating materials such as polytetrafluoroethylene (PTFE) or rubber to prevent short-circuiting of the induced voltage and to provide corrosion resistance. Excitation coils mounted on the exterior generate the uniform magnetic field, while electrodes embedded in the liner detect the voltage without contacting moving parts, ensuring no obstruction to flow and minimal maintenance. This non-intrusive configuration allows for bidirectional measurement and is particularly suited for pipes ranging from small diameters to large industrial sizes.^[81]^[82]^[83] Key advantages include zero pressure drop due to the absence of internal obstructions, high corrosion resistance from the liner and limited wetted electrode surfaces, and insensitivity to fluid density, viscosity, temperature, or pressure variations, making them ideal for challenging fluids like slurries. However, they require the fluid to have a minimum conductivity, typically greater than 5 μS/cm (though lower values like 1–3 μS/cm may suffice for larger pipe diameters depending on the model), and cannot measure non-conductive media such as gases or pure hydrocarbons. The first commercial magnetic flowmeter was introduced by KROHNE in 1952, revolutionizing flow measurement for conductive liquids in industrial applications.^[84]^[85]^[86] These devices achieve typical accuracies of ±0.2% to ±0.5% of the reading over a wide turndown ratio and support bidirectional flow detection, which is essential for processes involving reverse flows. Common applications encompass water and wastewater treatment, chemical processing, mining slurries, and pulp and paper industries, where their robustness and hygiene compatibility (with appropriate liners) ensure reliable performance. Unlike ultrasonic flowmeters, which apply to a broader range of fluids including non-conductives via sound wave propagation, magnetic flowmeters are specialized for conductive liquids through electromagnetic induction.^[87]^[88]^[79]

Ultrasonic Flowmeters

Ultrasonic flowmeters measure fluid velocity by analyzing the propagation of ultrasonic waves through the fluid in a pipe, offering a non-invasive or minimally invasive approach to flow quantification. These devices operate primarily in two modes: transit-time and Doppler. In the transit-time mode, suitable for clean, low-viscosity fluids, the meter sends ultrasonic pulses in both upstream and downstream directions along a known path length, measuring the difference in travel times caused by the fluid's motion. The time difference Δt is given by the approximation Δt = (2 L cos θ / c) × (v / c), where L is the path length, θ is the angle of the beam relative to the flow direction, c is the speed of sound in the fluid, and v is the fluid velocity; this simplifies to Δt ≈ 2 L v cos θ / c² for v << c. The volumetric flow rate Q is then determined by integrating the average velocity across the pipe's cross-section, often using multiple acoustic paths to account for velocity profile variations and improve accuracy.^[89]^[90] In the Doppler mode, applicable to fluids containing suspended particles, bubbles, or interfaces that reflect ultrasonic waves, the meter emits a continuous or pulsed signal and detects the frequency shift of the reflected waves due to the motion of reflectors in the flow. The Doppler frequency shift f_d is expressed as f_d = 2 f_0 (v cos θ / c), where f_0 is the transmitted frequency, v is the velocity component of the reflectors, θ is the incidence angle, and c is the speed of sound. This shift is proportional to the flow velocity, allowing calculation of Q after averaging over the measurement volume, though it requires sufficient reflectors for reliable signals and is less precise than transit-time for homogeneous flows.^[89]^[91] Designs of ultrasonic flowmeters include wetted types, where transducers are inserted into the pipe for direct contact with the fluid to achieve higher accuracy, and clamp-on types, which attach externally to the pipe surface for non-intrusive measurements without process interruption. Both typically employ contrapropagating beams—pairs of transducers alternating as transmitter and receiver—to enable bidirectional flow detection and enhance signal strength. Clamp-on designs, developed in the 1980s following initial ultrasonic prototypes in the 1960s, expanded applicability to retrofitting existing pipelines. Advantages encompass no pressure drop, compatibility with wide pipe diameters (from millimeters to meters), and suitability for corrosive or high-temperature fluids in clamp-on configurations; however, disadvantages include sensitivity to air bubbles, foam, or solids that attenuate signals, particularly in transit-time mode, and reduced performance in highly turbulent or multiphase flows.^[92]^[93] Applications of ultrasonic flowmeters span custody transfer in oil and gas pipelines, where precise billing requires high reliability, and leak detection in water distribution systems by monitoring flow discrepancies. Historical development traces to the 1960s, with early industrial models building on 1950s medical Doppler applications by researchers like Shigeo Satomura, evolving into practical pipe flow meters by the 1970s and clamp-on variants in the 1980s for broader industrial use. Transit-time models typically achieve accuracy of ±1% of reading under ideal conditions, such as fully filled pipes and stable temperatures, outperforming Doppler's ±2-5% in clean fluids.^[94]^[95]^[96]

Optical and Laser-Based Flowmeters

Laser Doppler Methods

Laser Doppler methods, particularly laser Doppler velocimetry (LDV), enable precise, point-wise measurement of fluid velocity by exploiting the Doppler shift in laser light scattered from tracer particles in the flow. Developed in the 1960s, this technique has become a cornerstone for non-intrusive flow diagnostics in controlled environments. The core principle of LDV relies on the frequency shift of light scattered by particles moving through an interference pattern formed by intersecting laser beams. When two coherent laser beams cross at an angle $2\theta, they create a fringe pattern with spacing \delta = \frac{\lambda}{2 \sin \theta}, where \lambda is the laser wavelength. As a particle traverses these fringes, the scattered light undergoes a Doppler shift \Delta f = \frac{2 v \sin \theta}{\lambda}, where v is the velocity component perpendicular to the bisector of the beams; this frequency is detected to compute velocity.^[97] The setup typically involves a continuous-wave laser (e.g., He-Ne at 632.8 nm), beam splitters to create the intersecting beams, a focusing lens to define a small measurement volume (on the order of micrometers), and a photodetector such as a photomultiplier tube to capture the scattered light off-axis. For multi-component measurements, additional beam pairs or color-separated lasers are used to resolve 2D or 3D velocity vectors. Frequency shifting via Bragg cells aids in direction discrimination and signal processing.^[97] LDV offers key advantages including non-intrusiveness, high spatial resolution (down to 10-100 \mum), and velocity resolution as fine as 0.1 mm/s across a wide dynamic range from mm/s to hundreds of m/s, making it ideal for transient and turbulent flows without calibration drift. However, it requires seeding the flow with micron-sized particles (e.g., smoke or polystyrene spheres) to ensure sufficient scattering, which can be challenging in clean or low-density fluids, and the method is generally confined to laboratory settings due to optical alignment sensitivities and sensitivity to environmental noise. To derive mean flow velocities or turbulence statistics, such as Reynolds stresses, data are collected over an integration period (typically seconds to minutes) by ensemble averaging multiple particle realizations passing through the probe volume.^[97]^[98] Applications of LDV span research domains, including aerodynamic studies in wind tunnels for boundary layer profiling and vortex dynamics, as well as biomedical assessments of microvascular blood flow via laser Doppler flowmetry adaptations. Historically, the technique originated from work by Yeh and Cummins in 1964, who first demonstrated velocity measurements in water using a He-Ne laser spectrometer. Recent developments include photonic Doppler velocimetry (PDV) for high-speed applications and multiplexed systems for multi-channel measurements, enhancing capabilities in dynamic flow diagnostics as of 2025.^[97]^[99]^[100]

Optical Flow Techniques

Optical flow techniques encompass imaging methods for visualizing and quantifying fluid flows, providing full-field velocity data without direct intrusion into the flow. These approaches rely on optical phenomena such as particle tracking, tracer diffusion, and refractive index variations to capture spatial flow patterns. Unlike point-wise measurements, they enable simultaneous analysis over extended regions, making them valuable for complex flow studies.^[101] Particle image velocimetry (PIV) is a prominent optical technique where a thin laser sheet illuminates seeded tracer particles in the flow field, and a high-resolution camera captures double-frame or double-exposure images separated by a short time interval. The particle displacements between frames are determined through cross-correlation analysis of small interrogation windows, yielding velocity vectors as v = \frac{\Delta x}{\Delta t}, where \Delta x is the displacement and \Delta t is the time separation. Developed in the late 1980s with the advent of digital cameras, PIV evolved from analog photographic methods to enable real-time processing and higher resolution. It achieves sub-pixel accuracy, typically with a standard deviation of approximately ±0.05 pixels for displacement estimation under optimal conditions.^[101]^[102]^[101] Dye tracing involves injecting a visible dye, such as rhodamine WT, into the flow to observe tracer paths for qualitative velocity assessment or quantitative discharge calculation. In slug injection, a concentrated dye pulse is released, and the time of travel over a known distance provides mean velocity; for discharge, continuous injection allows measurement of dilution at downstream points using fluorometry. This method is particularly effective in open channels or pipes where visual tracking is feasible.^[103]^[103] Shadowgraphy and schlieren imaging detect density gradients in gaseous flows by exploiting light refraction. Shadowgraphy projects shadows of refractive index variations onto a screen, while schlieren uses a knife-edge to block deflected rays, enhancing sensitivity to first derivatives of density changes. These techniques visualize shock waves and compressible flows without seeding, as seen in wind tunnel experiments.^[104]^[104] Optical flow techniques offer advantages like non-intrusive full-field measurements, capturing instantaneous velocity maps that reveal turbulence structures and flow instabilities. However, they require clear optical access to the measurement volume and involve intensive post-processing for data extraction, limiting applicability in opaque or confined environments. PIV and schlieren are widely applied in wind tunnels for aerodynamic testing and in microfluidics for analyzing low-Reynolds-number flows in lab-on-a-chip devices. Dye tracing complements these in environmental and hydraulic studies, such as stream discharge validation. Recent advances include the integration of deep learning and neural optical flow methods for enhanced particle tracking and velocity estimation in PIV, improving accuracy and enabling real-time analysis as of 2025.^[105]^[106]^[107]

Open-Channel and Environmental Flow Measurement

Level-to-Flow Methods

Level-to-flow methods estimate the volumetric flow rate (discharge, Q) in open channels by measuring the water level or stage (H) and applying established hydraulic relationships between stage and flow. These techniques rely on the geometry of the channel or structure to infer flow without direct velocity measurement, making them suitable for natural or engineered waterways where stage data is readily observable. The core principle involves rating curves that correlate stage to discharge, often derived from empirical or theoretical formulas accounting for channel cross-section, roughness, and slope. In uniform open-channel flow, discharge is commonly calculated using Manning's equation, which expresses Q as Q = (1/n) A R^{2/3} S^{1/2}, where n is the Manning roughness coefficient, A is the cross-sectional area of flow, R is the hydraulic radius (A divided by the wetted perimeter), and S is the channel slope. This semi-empirical formula, developed by Robert Manning in 1890, assumes steady, uniform flow and is widely applied to natural rivers and artificial channels by adjusting n based on surface materials like vegetation or concrete (typically 0.03–0.05 for clean channels). For non-uniform flow in structures like weirs or flumes, rating equations are used instead; for example, a rectangular sharp-crested weir follows Q = 1.705 H^{3/2} L, where L is the weir length and H is the head over the crest, based on dimensional analysis and calibration data. Stage measurement devices are essential for implementing these methods, with staff gauges providing visual manual readings along a fixed scale on a channel bank, accurate to within 1–2 mm under ideal conditions. Automated systems employ pressure transducers submerged or mounted above the water surface to detect hydrostatic pressure proportional to stage, offering continuous data logging with resolutions as fine as 0.1 mm and minimal maintenance in remote sites. For critical flow conditions that ensure accurate head-discharge relationships, engineered structures like the Parshall flume (developed in 1922) or Cippoletti weir are installed; the Parshall flume, a trapezoidal channel with a throat constriction, measures head upstream and downstream to compute Q via a predefined rating curve that accounts for subcritical to supercritical transitions, achieving accuracies of ±2–5% without calibration in many cases. These methods offer significant advantages, including simplicity, low installation and operational costs (often under $1,000 for basic setups), and non-intrusive operation that avoids flow disruption, making them ideal for long-term monitoring. However, they require site-specific calibration to develop accurate rating curves, as natural channel variations like scour or deposition can shift the relationship, and sediment buildup may reduce precision by 10–20% in silty environments. Additionally, extrapolation beyond the calibrated stage range introduces errors exceeding 15% during floods. Historically, level-to-flow techniques trace back to 19th-century hydraulic engineering, with James B. Francis introducing a foundational weir formula in 1877 for rectangular weirs, Q = 3.33 L H^{3/2} (in English units), derived from experiments on mill dams and later refined for metric use. Modern applications dominate river gauging and irrigation systems worldwide; for instance, the U.S. Geological Survey uses these methods at over 11,000 streamgages as of 2025 to monitor discharge for water resource management, while in agriculture, they control canal flows to optimize crop irrigation with minimal infrastructure. Rating curves, plotting discharge Q against stage H, are typically constructed from periodic direct measurements and fitted empirically, often logarithmically for natural channels where Q ∝ H^b with b ≈ 1.5–3.0 reflecting varying wetted area with depth. In straight, prismatic channels, the curve is more linear, but meandering rivers exhibit hysteresis during rising and falling stages due to transient storage effects, necessitating dynamic adjustments for real-time estimates. These curves enable continuous discharge computation from stage records, supporting flood forecasting and environmental assessments with uncertainties generally below 10% within calibrated ranges.

Velocity and Acoustic Methods

Velocity-based methods for flow measurement in open channels directly assess water speed through mechanical or acoustic sensors, enabling the computation of discharge by integrating velocities across the cross-section. These techniques are particularly suited for dynamic environments like rivers and coastal areas, where profiling at multiple depths provides a detailed vertical velocity distribution. Traditional mechanical current meters and advanced acoustic Doppler systems represent key approaches, offering real-time data for hydrological analysis. Current meters, often employing propeller or impeller mechanisms, measure local water velocity by detecting the rotation rate of a helix or turbine exposed to the flow. These devices are typically deployed at multiple depths along verticals in the channel cross-section to capture the velocity profile, with discharge calculated as Q = \sum (A_i v_i), where A_i is the partial area of each segment and v_i is the average velocity in that segment. A common approximation for the vertical velocity distribution in uniform open-channel flow is the 0.6H method, which estimates the depth-averaged velocity as approximately equal to the velocity measured at 0.6 times the water depth (H) from the surface, simplifying single-point measurements while maintaining reasonable accuracy for many natural streams.^[108] Acoustic Doppler velocimetry (ADV) advances velocity profiling by using sonar-like acoustic pulses to determine three-dimensional flow velocities through the Doppler shift in backscattered signals from particles in the water. Operating at sampling rates from 1 to 100 Hz, ADV focuses on a small measurement volume (typically <1 cm³) near the sensor, providing high-resolution data for turbulent flows without mechanical contact. This non-intrusive approach excels in laboratory and field settings for capturing instantaneous 3D velocity components.^[109]^[110] For broader profiling, acoustic Doppler current profilers (ADCPs) emit acoustic beams across multiple angles to map velocity profiles vertically or horizontally, extending measurements up to 300 m in low-frequency configurations suitable for deep waters. Discharge is derived by integrating the profiled velocities over the channel cross-section, often using bottom-tracking or GPS for positioning in moving-boat surveys. Developed commercially in the 1980s by RD Instruments, ADCPs revolutionized oceanographic and riverine monitoring by enabling remote, profile-based assessments.^[111] These methods offer significant advantages, including real-time velocity profiles that support dynamic flow analysis in varying conditions. However, they are susceptible to biofouling on transducers, which can degrade signal quality over time, and interference from air bubbles, which scatter acoustic signals and introduce noise in aerated flows. Current meters, with their moving parts, face additional mechanical wear and fouling risks compared to acoustic systems.^[112]^[113] In applications, velocity and acoustic methods are widely used in oceanography for current mapping and in flood monitoring to assess rapid discharge changes in rivers. ADCPs, in particular, provide accuracies of ±1-5% for discharge measurements when calibrated against reference methods, making them reliable for environmental management.^[114]^[115]

Calibration and Validation Techniques

Primary Calibration Methods

Primary calibration methods for flow measurement establish the accuracy of flowmeters by comparing their output to reference standards derived from fundamental physical principles, such as mass or volume, ensuring traceability to national metrology institutes like the National Institute of Standards and Technology (NIST). These techniques are essential for achieving high precision in applications requiring custody transfer or regulatory compliance, with uncertainties often below 0.2%.^[116]^[117] Gravimetric calibration, a primary method for liquid flowmeters, involves collecting the fluid output over a precise time interval and measuring its mass using a high-resolution balance, from which the volumetric flow rate Q is calculated as Q = \frac{m}{\rho t}, where m is the mass, \rho is the fluid density, and t is the time. This approach is particularly effective for water and other Newtonian liquids, achieving uncertainties as low as ±0.1% in controlled laboratory settings.^[116]^[118]^[119] Volumetric tank calibration employs calibrated tanks or vessels to measure the volume of fluid filled or drained over time, providing a direct reference for flow rate determination. For custody transfer applications, prover loops—closed systems with known volumes—are used to verify positive displacement (PD) meters by displacing fluid through the loop and timing the transit. Pipe prover spheres, typically spherical displacers that form a seal within the pipe, are launched through these loops in PD meter calibration to measure the effective volume swept, ensuring repeatability within 0.02%.^[120]^[121]^[122] The master meter method calibrates a flowmeter against a reference meter previously verified against a primary standard, often through ratio testing where the flow rates are compared at multiple points across the operating range. This technique is efficient for field or secondary calibrations, maintaining traceability to NIST standards while minimizing setup complexity.^[116]^[123] Primary calibrations are categorized as static or dynamic: static methods, like gravimetric weighing, involve stopping flow to measure accumulated mass or volume, ideal for high accuracy but limited to lower flow rates; dynamic methods, such as continuous collection in flying start-and-stop systems or master meter comparisons, simulate operational conditions for broader range coverage.^[116]^[124]^[119] International standards govern these methods, including ISO 4185 for liquid flow in closed conduits using weighing techniques, and ASME MFC series (e.g., MFC-3M for differential pressure devices and MFC-7 for critical flow venturis in gases), ensuring consistent procedures and uncertainties. Traceability to NIST is achieved through calibrated artifacts and reference facilities, such as their dynamic gravimetric liquid flow standards.^[117]^[125]^[126]^[127] Historically, early bell provers emerged in the early 20th century for gas flow calibration, using a rising inverted bell over a liquid bath to measure displaced volume against meter output, laying the foundation for modern volumetric standards.^[128]^[129]

Tracer and Optical Validation

Tracer and optical validation methods provide in-situ techniques for verifying flow measurements in real-world settings, particularly where direct access or disruption is impractical, such as in large rivers, pipes, or environmental flows. These approaches leverage injected tracers or optical detection to estimate flow rates independently of installed meters, enabling calibration and uncertainty assessment without halting operations.^[130] The tracer dilution method involves injecting a tracer solution of known concentration C_{in} at a constant rate Q_{in} into the flow stream, then measuring the diluted concentration C_{out} at a downstream sampling point after complete mixing. The total flow rate Q is calculated as Q = \frac{Q_{in} C_{in}}{C_{out}} - Q_{in}, accounting for the injection volume itself. This technique is particularly suited for rivers, open channels, and pipes where uniform mixing can be achieved, often using salts like sodium chloride or fluorescent dyes as tracers. Historically, salt dilution methods emerged in the early 20th century, with practical applications documented from the 1920s for gauging river discharges.^[130]^[131]^[132] In the transit-time tracer method, a pulse of tracer—such as dye, salt, or radioactive material—is injected into the flow, and the time \Delta t for it to travel a known distance L between upstream and downstream sensors is measured to determine velocity v = \frac{L}{\Delta t}. The flow rate is then Q = v A, where A is the cross-sectional area. This approach is effective for steady flows in conduits or channels, with sensors detecting the tracer arrival via conductivity, fluorescence, or radiation. It is standardized in ISO 2975-7 for radioactive tracers and ISO 2975-6 for non-radioactive ones, offering traceability for in-situ validation.^[133] Optical validation enhances tracer methods by employing laser-based or video techniques to detect and track tracer movement non-invasively, especially for low flows or surface velocities. Laser transit methods illuminate the tracer pulse and time its passage across a light sheet, while video tracking analyzes particle or dye motion using optical flow algorithms to estimate velocities. Fluorescent tracers, excited by lasers and detected via emitted light, improve sensitivity in turbid waters, as in laser-induced fluorescence (LIF) systems where concentration profiles yield dilution-based flows. These optical integrations allow for two-dimensional velocity mapping in open channels or pipes.^[134]^[135]^[136] Advantages of tracer and optical validation include minimal disruption to large-scale systems like rivers or wastewater conduits, enabling field measurements where lab calibration is infeasible. However, challenges arise from tracer dispersion, which can introduce errors if mixing is incomplete, and potential environmental impacts from chemical tracers requiring regulatory compliance. Applications span hydraulics for river gauging, wastewater treatment for effluent monitoring, and industrial pipes for multiphase flows. Typical uncertainties range from ±2-5% under optimal conditions, as specified in ISO 2975, depending on mixing quality and detection precision.^[130]^[137]

References

[1]
[PDF] Introduction to liquid flow metering and calibration of liquid flowmeters
References to more complete sources of properties of liquids, theo- retical relations and instructions for metering and calibrating have been included. Separate ...
[2]
Understanding Flow Meters | NIST
Mar 10, 2014 · We study the operating principles of a wide range of flow meters. We concentrate on those meters that we use as 1) working standards.
[3]
[PDF] A guide to methods and standards for the measurement of water flow
standards of physical measurement, fundamental con- stants, and properties of matter. Issued six times a year. Annual subscription: Domestic, $17.00 ...
[4]
https://www.blue-white.com/article/flow-meter-types-their-functions/
[5]
Mass Flow Rate vs Volumetric Flow Rate
Mar 8, 2024 · Volumetric flow rate is mathematically defined as the cross-sectional area of a tube multiplied by the velocity of the fluid. It simply measures ...
[6]
Mass Flow vs Volumetric Flow - Alicat Scientific
Mass flow measures the number of molecules, while volumetric flow measures the volume of fluid, which is affected by temperature and pressure.
[7]
Continuity Equation - Fluid Flow - Engineering Library
The continuity equation expresses the relationship between mass flow rates at different points in a fluid system under steady-state flow conditions.Missing: derivation | Show results with:derivation
[8]
[PDF] Derivation of the Continuity Equation (Section 9-2, Çengel and ...
The mass flow rate through each face is equal to ρ times the normal component of velocity through the face times the area of the face. We show the mass flow ...
[9]
Industrial Flow Meters: Comparing the Features, Benefits, and ...
Jun 3, 2024 · Accurate flow measurement is critical across a wide range of industries, including water and wastewater treatment, oil and gas, chemical ...
[10]
[PDF] history of water measurement and water meters | aplmf
Oct 18, 2019 · HISTORY. Venturi Tube. In 1790 Giovanni Venturi published a paper on a metering device and the meter was invented by Clemens Herschel (1842 - ...
[11]
What is Reynolds Number (Re)? (Complete Guide) | SimScale
Jul 31, 2024 · Reynolds number, referred to as Re, is used to determine if a fluid flow is laminar or turbulent. It is the ratio of inertial to viscous ...Derivation · Fluid, Flow, and Reynolds... · Internal Flow · External Flow
[12]
Laminar and Turbulent Flow | Engineering Library
The flow regime (either laminar or turbulent) is determined by evaluating the Reynolds number of the flow (refer to figure 5). The Reynolds number, based on ...
[13]
The Impact of Reynolds Number on Differential Pressure Flow ...
There are 3 types of flow regimes; Laminar, transitional and turbulent. Laminar flow occurs when the Reynolds number fall below 2000. Above 4000, the flow ...
[14]
(PDF) Introduction to Multiphase Flows Part #1 Classification of ...
Jan 6, 2017 · Classification of Multiphase Flows: Gas-Liquid or Liquid-Liquid Flows ... Slurry flow: This flow is the transport of particles in liquids.
[15]
Multiphase Flow - Thermopedia
Sep 7, 2010 · The most common class of multiphase flows are the Two-Phase Flows, and these include Gas-Liquid Flow, Gas-Solid Flow, Liquid-Liquid Flow and ...Solids · Liquids · Gases<|separator|>
[16]
Laminar vs. Turbulent Flow - Reynolds Number Explained with ...
Reynolds Number for Flow in Pipe or Duct. For a pipe or duct the characteristic length is the hydraulic diameter. L = dh. where. dh = hydraulic diameter (m, ft).
[17]
Gas Laws and their influence on Natural Gas Flow Measurement
May 7, 2013 · Gay Lussac's Law (ideal gas law) states that a gas's pressure is proportional to the absolute temperature. In other words, if we double the ...
[18]
Cavitation | The Lee Company
Liquid flowing through any orifice will cavitate whenever its velocity causes the pressure in the throat of the orifice to drop below the vapor pressure.
[19]
Detecting and Preventing Pump Cavitation - KNF
Oct 1, 2025 · A high vapor pressure, as is the case with ethanol, for example, increases cavitation compared to fluids with a lower vapor pressure, such as ...
[20]
Fluid Flowmeters - Comparing Types - The Engineering ToolBox
Flow is classified into open channel flow and closed conduit flow. Open channel flow occur when the flowing stream has a free or unconstrained surface open ...Missing: pros cons
[21]
CLOSED CONDUIT vs OPEN CHANNEL FLOW - Swapan Basu
Oct 7, 2018 · It is comparatively easier to measure flow in closed conduit than that in open channel mainly because position of free surface which frequently ...Missing: pros cons
[22]
Flowmeter Development History - News
Jul 29, 2020 · As early as 1738, the Swiss Daniel First Bernoulli used the differential pressure method to measure water flow based on the Bernoulli equation.
[23]
Positive Displacement Meter - an overview | ScienceDirect Topics
Positive displacement meters are widely used on applications where high accuracy and good repeatability are required. Accuracy is not affected by pulsating flow ...Missing: subtypes | Show results with:subtypes
[24]
API MPMS 5.2 - Manual of Petroleum Measurement Standards ...
This section of Chapter 5 covers the characteristics of displacement meters and discusses appropriate considerations regarding the liquids to be measured, the ...
[25]
Smith Meter® PD Meter reaches its 80th anniversary ... - TechnipFMC
Jul 9, 2020 · The Smith Meter® PD Meter – PD stands for Positive Displacement – was first built in 1940 in Erie, Pennsylvania.
[26]
Velocity - Visual Encyclopedia of Chemical Engineering Equipment
Apr 1, 2022 · Advantages · Accurate regardless of temperature, pressure, density and viscosity when flow is turbulent. · Suitable for measuring liquids, gases ...
[27]
A Guide to Turbine Flow Meters - KOBOLD USA
Paddle wheel flow meters offer a general accuracy of 2.5% to 5% and Pelton wheel flow meters offer an accuracy of 1.5% to 3%. To see a full explanation of flow ...Missing: Woltman principle
[28]
Difference between Single-Jet and Multi-Jet Water Meters
Oct 2, 2019 · Unlike single-jet meters, which have one port, multi-jet meters have multiple ports that surround an internal chamber to create a flow of water ...
[29]
Numerical Analysis of Woltman Meter Accuracy under Flow ... - MDPI
Quantifying Water Quality Improvements through Use of Precision Herbicide Application Technologies in a Dry-Tropical, Furrow-Irrigated Cropping System ...
[30]
Compact Pelton Type Paddle Wheel Flow Meter - DPM
The DPM flow sensor uses the pelton wheel principle to measure the flow of water and water-based, low-viscosity liquids that are optically transparent.
[31]
Paddle Wheel Flow Meters Explained - KOBOLD USA
Pelton wheel flow meters offer higher accuracy at 1.5% to 3%. For a simple mechanical flow meter based on a rotational principle of operation, the best accuracy ...Missing: Woltman current
[32]
Mechanical current meter with propeller - Royal Eijkelkamp
Small, lightweight mechanical current velocity meter, suitable for measurements in rivers, channels, sewage systems, pipes, and more.
[33]
[PDF] Reynolds Number, the Correct Calibration, Characterization and ...
Reynolds number is the ratio of inertia forces to viscous forces in a fluid. It affects flow meter performance, and all meters are beholden to it.
[34]
Woltman Irrigation Water Meter WI-N - ZENNER International
The WI-N water meter is designed fur use with heavily contaminated water, eg in agriculture, in sewage treatment plants or wastewater systems.
[35]
Orifice, Nozzle, Venturi Flow Meters & Bernoulli Equation
The orifice, nozzle and venturi flow rate meters makes the use of the Bernoulli Equation to calculate fluid flow rate using pressure difference through ...
[36]
[PDF] The Engineer's Guide to DP Flow Measurement | Emerson
Chapter 1 – The DP Flow Meter provides an overview of the history of DP flow and the basic principles that govern DP flow measurement. It introduces the ...
[37]
The History and Advantages of the Classical Venturi Flow Meter
Jul 9, 2019 · Introduced in the early 1900s, it is still widely specified worldwide particularly on applications that require ASME or ISO code compliance.Missing: 1884 | Show results with:1884
[38]
https://www.sino-inst.com/orifice-plate-installation-guidelines/
[39]
Advantages and Disadvantages of Orifice and Venturi meter
Nov 15, 2018 · The Orifice is small plates and easy to install/remove. · Offer very little pressure drop from which 60% to 65% is recovered. · The orifice meter ...Missing: loss | Show results with:loss
[40]
The Venturi Effect: Discovered by Giovanni Battista ... - EXAIR Blog
Jan 31, 2022 · The original purpose of the venturi tube was to measure the amount of water used in individual water mills and is still used to this day as a ...Missing: 1884 | Show results with:1884
[41]
The History of Flow Measurement
**Summary of History of Orifice Plate and Venturi Flow Measurement:**
[42]
[PDF] A history of fire testing - NIST Technical Series Publications
Following Bernoulli's lead, in 1732 a Frenchman named Henri Pitot developed a device useful in measuring fluid flows. This device carries the inventor's ...
[43]
Pitot Tube
The transducer measures the difference in pressure in the two groups of tubes by measuring the strain in a thin element using an electronic strain gauge. The ...
[44]
[PDF] method 2.1 determination of stack gas velocity and volumetric flow ...
This method measures the average velocity of a gas stream from which gas flow is quantified.<|control11|><|separator|>
[45]
[PDF] ASGMT / Averaging Pitot Tube Flow Measurement
These published flow coefficients are used for flowmeters in nearly all untested conditions and vary by design of the averaging pitot tube, which includes bar.
[46]
Measuring Mechanical Ventilation Airflow
Jul 9, 2022 · A pitot tube can be used to measure velocity pressure in a duct; at least twelve measurements are taken across the duct and velocity pressure is ...
[47]
[PDF] Method 2—Determination of Stack Gas Velocity and Volumetric Flow ...
Aug 2, 2017 · After verifying the face opening alignment, measure and record the following dimensions of the pitot tube: (a) the external tubing diameter ( ...Missing: HVAC | Show results with:HVAC
[48]
[PDF] TECHNICAL REPORT Guidelines on Flare and Vent Measurement
Sep 18, 2008 · Dirty gas or liquid flows can cause problems with the sensing ports on the Pitot tubes. Purging systems can be used to reduce or eliminate ...Missing: uniform | Show results with:uniform
[49]
[PDF] Improving Fan System Performance - A Sourcebook for Industry
Another inlet condition that can interfere with fan performance is highly non-uniform flow. As shown in Figure 2-17, placing a bend too close to a fan inlet ...
[50]
[PDF] Instrumentation Note: The Surprisingly Confusing World of Rotameters
A rotameter consists of a vertical, variable-area tube, small at the bottom and large at the top. Flow enters at the bottom, moves upward through the tube, and ...
[51]
Variable Area Flow Meters (Rotameters) - Brooks Instrument
A rotameter, or variable area flow meter, measures the volumetric flow of liquids and gases. It uses a float to measure flow rate.
[52]
Float types for variable area flowmeters (II) - Tecfluid
Nov 22, 2017 · The float types include ball floats (ceramic, glass, stainless steel) and conical floats (AC type, guided, for glass/plastic or metal tubes).
[53]
Variable Area (Float Style) Flowmeters for Clean Gas
Variable area flowmeters are commonly used to provide cost-effective local indication of small liquid or gas flows, such as for purging in the mining, mineral ...
[54]
Rotameters (Variable Area Flow Meters) Explained - KOBOLD USA
Rotameters are known for being highly repeatable. There are other flow meter technology types that will offer higher accuracy, like magnetic and ultrasonic flow ...
[55]
[PDF] User's Guide for Industrial Rotameters - DwyerOmega
Standard construction has brass end fittings for mounting. The meters feature ±2% full scale accuracy, ±1/2% full scale repeatability, and are shielded for use ...
[56]
Variable Area Flowmeter - History and development
The first mention of the measurement of flow in a conical pipe with a float was made by the American Edmund A. Chameroy, who applied for a patent for his ...
[57]
(PDF) Karman Vortex Shedding And The Strouhal Number
This report is concerned with Karman vortex shedding. The specific purpose is to discuss the Strouhal number which relates the frequency of Karman vortex ...
[58]
[PDF] karman vortex shedding and the strouhal number - Vibrationdata
Apr 7, 2009 · The fs value shall be called the "Strouhal frequency" rather than the "vortex shedding frequency" in this report because periodic vortex ...Missing: principle | Show results with:principle
[59]
https://tek-trol.com/measurement-basics/vortex-flow-meter/
[60]
How vortex flow meter works - Tek-Trol
The Strouhal number is a function of the Reynold's number. Reynold's number is also a dimensionless parameter which is used to determine how the flow pattern of ...
[61]
Vortex Flow Meter Technical Guide | Sino-Inst
Dec 11, 2019 · Vortex flow meter has irreplaceable advantages, extremely high sensitivity, and the lower limit of gas flow rate can be as low as 2m/s. It is ...
[62]
Benefits and Shortcomings of Vortex Flowmeters - ISA Interchange
Vortex flowmeters are a good choice for measuring the flow rate of any reasonably clean fluid where measurement at very low flows is not required.Missing: history accuracy
[63]
https://www.asme.org/topics-resources/content/an-example-of-a-vortex-shedding-flowmeter
[64]
Vortex Shedding Flowmeters - ASME
Mar 29, 2019 · Because vortex shedding flowmeters are ruggedly built they are often used in harsh or challenging conditions, such as measuring cooling water, ...Missing: disadvantages history
[65]
The Evolution of Flow Measurement Technology: A History of ...
Apr 10, 2025 · The history of Venturi flow meters dates back to 1797, when Italian physicist Giovanni Battista Venturi discovered the pressure change ...
[66]
[PDF] Recommended Practice for Flow Control and Measurement in ...
mass flow rate. The power required to maintain a constant temper- ature is then related to the mass flow rate using King's law: Pheater. Poffset. C _mn. (7).
[67]
Direct Mass Flow or Volumetric: The Thermal Flow Meter ...
Nov 18, 2016 · Volumetric flow measurements are less reliable than mass flow measurements because changes in gas temperature and pressure effect measurement ...Missing: disadvantages | Show results with:disadvantages
[68]
[PDF] Micromachined Thermal Flow Sensors—A Review
Jul 23, 2012 · King's Law describes heat transfer from a cylinder of infinite length in terms of the resulting voltage difference and is useful for hot-wire ...
[69]
[PDF] The History & Evolution of Thermal Flowmeters - Sierra Instruments
Aug 20, 2013 · These instru- ments are based on thermal dispersion technology and have sensors consisting of heated tungsten wires or a thin plati- num film ...
[70]
[PDF] A Tale of Two Thermals: Capillary & Immersible - Sierra Instruments
Aug 7, 2008 · As a result, immersible thermal mass flow meters measure much higher gas mass flow rates in harsher environments than capillary thermal mass ...
[71]
Mass Flow - Visual Encyclopedia of Chemical Engineering Equipment
Apr 1, 2022 · Disadvantages · Extremely sensitive to solid particles, the gas must be very clean · Point measurements only so provide no information on the flow ...
[72]
Thermal mass flow meter - OMEGA Engineering
Some common gas-flow applications for thermal mass flowmeters include combustion air measurement in large boilers, semiconductor process gas measurement, air ...
[73]
Thermal Mass Flow Meters | Sierra Instruments
Wide Turndown Ratio: Sierra's thermal mass flow meters feature turndown of up to 1000:1, allowing you to measure both very low and very high flows with a ...
[74]
Coriolis Flow Meter Principles | Emerson US
The basic operation of Coriolis flow meters is based on the principles of motion mechanics. As fluid moves through a vibrating tube it is forced to accelerate ...
[75]
Understanding Coriolis flowmeters: Features and benefits | Endress+Hauser
**Summary of Coriolis Flow Measuring Principle (Endress+Hauser)**
[76]
Coriolis Flowmeter Advantages and Limitations - InstrumentationTools
Oct 31, 2023 · Coriolis mass flowmeters are very accurate and dependable. They are also completely immune to swirl and other fluid disturbances.<|separator|>
[77]
Micro Motion™: A History of Innovation | Emerson US
Micro Motion founded by Jim Smith ; First Dual Tube Coriolis Meter. 1983 — Micro Motion ...
[78]
Coriolis flowmeters, Part 3: Flowmeter design - EE World Online
Mar 4, 2020 · In 1977, Micro Motion Inc introduced the first standard industrial flow meter based on the effect.<|control11|><|separator|>
[79]
Theory of Magnetic Flow Meters | Emerson US
... E=k*B*D*V. The induced voltage (E) is directly proportional to the velocity (V) of the fluid moving through the magnetic field (B). The induced voltage is ...
[80]
Electromagnetic Flowmeter - an overview | ScienceDirect Topics
When a conductor of length l moves at right angles to a magnetic field of density B at a velocityof v, an induced e.m.f. e is generated, given by e =Blv (see ...
[81]
[PDF] NACA RESEARCH MEMORANDUM
The principle of the electromagnetic flowmeter is similar to that of a ... is given by Faraday's law,. E B 2 v X 10-8 where. E induced voltage. B magnetic ...
[82]
Magnetic Flow Meters & Switches | KOBOLD USA
A magnetic flow meter consists of the flow meter body, a non-conductive flow tube liner embedded into the body, two electrodes, a magnetic coil, seals, and a ...
[83]
Electromagnetic (Mag) Flow Meters - FTI Flow Technology
Line Sizes: 1″ to 12″ · Electrode Material: Hastelloy C · Liner Material: Ebonite or PTFE · Min Conductivity: 5 µS/cm, 20 µS/cm for DI water · Rating: IP68 to a ...
[84]
Electromagnetic flow measuring principle - Endress+Hauser
Dec 3, 2024 · Given a magnetic field of constant strength (B), the equation Ue = B ⋅ L ⋅ v shows that the induced measuring voltage (Ue) is directly ...Missing: formula | Show results with:formula
[85]
Krohne Profile - May 2014 - SA Instrumentation & Control
These acclaims go back to 1953 when Krohne produced the first commercial magnetic flowmeter. 1973 saw Krohne launch the first pulsed DC electromagnetic ...<|control11|><|separator|>
[86]
Recommended Practice for the Use of Electromagnetic Flowmeters ...
The operation of electromagnetic flowmeters is based on the Faraday law of electromagnetic induction. If flow of a conductive fluid in a pipe is normal to a ...
[87]
What is the minimum required conductivity for a liquid ... - Yokogawa
What is the minimum required conductivity for a liquid when using an AXF Magnetic Flow Meter? Sizes 2.5 to 10 mm (0.1 to 0.4 in): 5 µS/ ...
[88]
Electromagnetic Flow Meters Achieve High Accuracy in Industrial ...
They can achieve relatively high system accuracies (0.2%) at low and high volume flow rates with a minimum diameter of about 0.125 inches and a maximum volume ...
[89]
https://www.omega.co.uk/technical-learning/dif-between-doppler-transit-time-ultrasonic-flow-meters.html
[90]
Differentiating Between Doppler & Transit Time Ultrasonic Flow Meters
T2 = Transit time of waves from downstream transmitter to upstream transmitter t = Transit time of waves through pipe wall and lining. The above equation ...
[91]
Ultrasonic flow measuring principle - Endress+Hauser
Dec 3, 2024 · Transit time differential method: Measures flow by comparing the time it takes for ultrasonic pulses to travel with and against the fluid flow.
[92]
Ultrasonic Doppler and Time of Flight Velocity and Volume Flow ...
The resulting frequency shift is named the Doppler Effect. Dopler ultrasonic flow meter. Fluid velocity can be calculated as. v = c (fr - ft) / (2 ft cos(Φ) ...
[93]
Ultrasonic Flowmeter Market Exceeds $600 Million - Automation.com
The use of ultrasonic meters for gas flow measurement has evolved substantially from the late 1970s and early 1980's, when this was first attempted. The use of ...<|separator|>
[94]
All About Ultrasonic Flow Meters - KOBOLD USA
Shigeo Satomura was a Japanese physicist who developed the first ultrasonic flow meter, based on the Doppler principle, for the analysis of the flow of blood.
[95]
Ultrasonic Flow Meters | Emerson US
Applications: Custody transfer; System balancing; Allocation measurement; Check metering; Inventory control; Power plants; Leak detection; Underground storage ...
[96]
[PDF] Fundamentals of Multipath Ultrasonic Flow Meters for Gas ... - ASGMT
The net result for the Doppler ultrasonic flowmeter is a frequency shift between the Doppler signal transmitted and the signal received. This difference in ...
[97]
Industrial experiences show clamp-on ultrasonic transit time flow ...
The manufacturers claim accuracy is about 1% (Table 1). These are some of the reasons that UTTFM are the most popular ultrasonic flow meter in the market.
[98]
None
Summary of each segment:
[99]
[PDF] Description of the Laser Doppler Velocimetry Method For Flow ...
• First HeNe laser developed at Bell Labs. 1962. • Originated in 1964 by Yeh and Professor Cummins. • Measurements made non-intrusively and in situ. • Velocity ...
[100]
Review of methodological developments in laser Doppler flowmetry
Jan 31, 2008 · The major advantage of the laser Doppler techniques in general is their non-invasiveness and their ability to measure the microcirculatory flux ...
[101]
Particle Image Velocimetry - an overview | ScienceDirect Topics
The general principle of PIV is to illuminate the tracer particles in a flow field using a laser sheet, and then acquire two images of the diffracted light ...
[102]
Particle image velocimetry - Classical operating rules from today's ...
In the case of well performed experiments and evaluations the particle image displacement can be determined with a standard deviation around σΔx ≈ 0.05 pixel ...
[103]
[PDF] measurement of time of travel in streams by dye tracing
The measurement or simulation of time of travel using dye tracers involves the slug injection of a dye at some location along the stream and the rneasurement of ...
[104]
Schlieren Flow Visualization
Schlieren systems are used to visualize the flow away from the surface of an object. The schlieren system shown in this figure uses two concave mirrors on ...<|separator|>
[105]
Aerodynamic Testing: PIV in Wind Tunnels - LaVision
Multidimensional and often time-resolved Particle Image Velocimetry (PIV) measurements are applied in wind tunnels to balance aerodynamic shape with automotive ...
[106]
Progress towards a Miniaturised PIV System - MDPI
Nov 13, 2022 · A miniaturised PIV system has been developed that can be situated within a wind tunnel model. This system utilises a combination of off-the- ...
[107]
Contrast Analysis of Flow-Discharge Measurement Methods in a ...
To represent the vertical-average velocity, the new method selects the point velocity at 0.2H, 0.5H, and 0.8H. “Liquid-flow measurement in open channels—Flow ...
[108]
[PDF] ACOUSTIC-DOPPLER VELOCIMETER (ADV) FOR LABORATORY ...
Doppler principle and measures the 3D velocity at a rate of 25 Hz in a sampling volume of less than 1 cm³. The sensor is mechanically rugged, can be used in.Missing: sonar | Show results with:sonar
[109]
Evaluation of the Acoustic Doppler Velocimeter (ADV) for ...
The analysis showed that the ADV sensor can measure mean velocity and Reynolds stress within 1% of the estimated true value.
[110]
[PDF] Best Practices for Measuring Discharge with Acoustic Doppler ...
Various methods for testing ADCP accuracy include tow-tank tests, flume tests, and comparing ADCP discharge measurements with discharges from some other source, ...
[111]
Acoustic Doppler Current Profiler - an overview | ScienceDirect Topics
An Acoustic Doppler Current Profiler (ADCP) uses ultrasonic sound waves and the Doppler effect to measure water velocity and discharge in streams.Fluvial-Tidal Sedimentology · 2.2. 1.2 Adcp Methods · 11.8 Towed Adps
[112]
(PDF) Bubble Effects on the Acoustic Doppler Velocimeter (ADV ...
Although measuring velocity with ADV has advantages over other velocity measurement methods, this technique is sensitive to operating conditions: in addition ...Missing: ADCP biofouling
[113]
[PDF] Discharge-Measurement System Using an Acoustic Doppler Current ...
ADCP-measured discharges differed less than 5 percent from simultaneous conventional dis- charge measurements, which was encouraging.
[114]
Acoustic Doppler Current Profiler - NOAA Ocean Exploration
Jun 22, 2020 · An acoustic Doppler current profiler, or ADCP, is a device that uses sound waves to measure the speed and direction of currents throughout ...
[115]
[PDF] NIST Calibration Services for Water Flowmeters
A normal flow calibration performed by the NIST Fluid Metrology Group is intended to quantify meter performance and its stability or precision. This is done by ...
[116]
ISO 4185:1980(en), Measurement of liquid flow in closed conduits
International Standard ISO 4185 was developed by Technical Committee ISO/TC 30, Measurement of fluid flow In dosed conduits, and was circulated to the member ...
[117]
[PDF] SOP 14 Gravimetric Calibration of Volumetric Standards Using an ...
The procedure uses an electronic balance and is suitable for all sizes of gravimetric calibrations only limited by the capacity and resolution of the balance.Missing: ISO 4185 ASME MFC
[118]
[PDF] 1 NIST's Fully Dynamic Gravimetric Liquid Flowmeter Standard ...
During a primary flow calibration the bypass remains closed and the flow is continuously either filling or being drained from the collection tank. The tank ...Missing: ISO 4185 ASME MFC<|control11|><|separator|>
[119]
[PDF] Fundamentals of Meter Provers and Proving Methods - ASGMT
The bidirectional pipe prover design sphere velocity must be between 0.5 feet per second and 10 feet per second, but in either design the prover must allow for ...
[120]
Volumetric Tank Provers - Meter Engineers
The Meter Engineers volumetric tank prover is used in the calibration of oil flow meters for fiscal, allocation or custody transfer measurements.
[121]
[PDF] conventional liquid meter provers – design and construction
C) Launch Chambers: The pipe section prior to the pre-run and calibrated section is used to launch and receive the sphere. Launch chambers are normally two pipe ...
[122]
Petroleum Flow Meter Calibration & Recalibration | LM&C Inc.
Dec 10, 2019 · A master meter is a flow meter which has been set according to the NIST standard. It is then taken to the site of the test meter and tested ...Master Meter Recalibration · Gravimetric Recalibration · Volumetric Prover...<|separator|>
[123]
[PDF] Flow calibration | NFOGM
Hybrid dynamic start-and-stop, static reading weight and volume systems generally provide more accurate liquid calibrations than purely static or dynamic ...
[124]
[PDF] ISO-4185-1980.pdf - iTeh Standards
This International Standard specifies a method of liquid flow- rate measurement in closed conduits by measuring the mass of liquid delivered into a weighing ...
[125]
Measurement of Gas Flow by Means of Critical Flow Venturis and ...
21-day returnsMFC-7 standard specifies the geometry and method of use for critical flow venturi nozzles to determine gas flow rate, when flow is critical.
[126]
ASME MFC-7–2016: Measurement of Gas Flow by Means of Critical ...
Sep 1, 2016 · This standard applies only to the steady flow of single-phase gases through critical flow venturis, CFVs, of shapes specified herein.
[127]
Natural Gas Meter Evolution - Linc Energy Systems
May 10, 2013 · The prover has been used since the early 1900s with the bell prover being commonly used as an industry reference standard.
[128]
Bell prover for testing gas meters - Powerhouse Collection
The bell prover was used to test that each meter accurately measured gas volume prior to installation. It was also used to check meters where there were ...
[129]
USBR Water Measurement Manual - Chapter 12
The tracer-dilution method consists of adding a known, strong concentration of tracer solution, C1 (equation 12-2) at a constant rate, to the flow (Schuster, ...
[130]
[PDF] Using the tracer-dilution discharge method to develop streamflow ...
At the Brandon Ditch gage, the tracer-dilution discharge measurements overestimated stream- flow by an average of 14 percent (fig. 3 and table 2). However, the ...Missing: validation | Show results with:validation
[131]
Flow Measurement of Water Turbine by Means of Salt Dilution Method
About ten years ago, the authors devised the method to measure the flow rate of the water turbine by seeking the rate of dilution of the water discharged ...
[132]
Flow-rate measurement using radioactive tracers and transit time ...
The transit time method is a flow measurement method based on tracer techniques. Measurement is done by injecting to the flow a pulse of tracer and ...
[133]
Fluorescent particle tracers for surface flow measurements: A proof ...
Jun 23, 2012 · Fluorescent microspheres can be used as particle tracers in natural streams Flow velocity and travel time can be estimated using fluorescent ...Missing: optical | Show results with:optical
[134]
Tracer gauge: An automated dye dilution gauging system for ice ...
Dec 30, 2008 · In this study, an automated dye dilution gauging system, a tracer gauge, was developed for measuring discharge in ice-affected streams.<|control11|><|separator|>
[135]
Tracer-based laser-induced fluorescence measurement technique ...
Here the laser-based optical measurement technique TLIF is described for using a different tracer system that allows us to gain quantitative two-dimensional ...Missing: validation | Show results with:validation
[136]
[PDF] Uncertainty estimates of tracer gas dilution flow measurements in ...
This study demonstrates the application of the tracer gas dilution method to measure the volume flow in a large-scale exhaust duct used for flue gas venting.